PROVN OF SEWAGE LINE , MANHOLES AND CONNECTED ALLIED SERVICES AT GURUBACHAN SINGH ENCLAVE, CEMETERY AREA -II ,OR MD ACCN AT ISHWAR NAGAR ,PROVN OF 12 X GEYSERS OF 25 LTR CAP IN COOK HOUSE AND SINGLE OFFRS ACCN OF 18 MED REGT, PROVN OF TOILET BLOCK

Amount

Surface excavation n.exc 30cm deep and averging 15 Cm and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches for foundation n.exc 1.5 meter wide and n exc. 1.5 meter depth and not exc. 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Removing excavated material(soils) n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Removing excavated materials for a distance exc 250 m & n exc 500 m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Returning, filling-in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

M&L for PCC 1:4:8 type D-2, (using 40mm graded stone aggregates) in foundation/filling mass concrete complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exc 6 cm mean radius built in cement mortar 1:6 all as specified.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 (using 20 mm graded aggregate) as in slabs complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection complete all as specified and directed.

M&L for TMT mild steel bar 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

-Ditto- but 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders -ditto-'

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; rough finished surfaces of conrete flat complete all as specified and directed.

Formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions rough finished surfaces of conrete flat complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of conrete flat complete all as specified and directed.

Use & waste of form work for rough finished surface to soffit of suspended slabs such as roof slabs, floor slabs, landing and similar work n.exc 200mm thick (horizontal or sloping) complete all as specified and directed.

Use & waste of form work for rough finished surface to edges of concrete flat, break in floor.cills,railings etc.& similar works, exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed.

M&L for cement plaster in two layers (10 + 5) first coat 10 mm thick in cement mortar 1:6 and second coat 5 mm in cement mortar 1:4 using WPC as nper manufacutrer instruction in 5 mm thick second layer on brick work or concrete surfaces finished even and fair. complete all as specified and directed. Note:- WPC shall me measured and paid supply only respective item of BOQ

M&L rendering 5 mm thick on ceiling in cement mortar 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound(powder) only.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of cement base primer on plastered surface of wall complete all as specifiedand directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specifed and directed.

M&L for three coats of white wash on newly plastered surface or unplastered surfaces of celling including preparation surface complete all as specifed and directed.

S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc.set and jointed in neat cement slurry @ 3 Kg per Sqm and pointed in white or coloured cement to match,over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S & F Glazed ceramic colured tiles in vertical surface 300x 450 x 7mm thick set and jointed in neat cement slurry @ 3 Kg per Sqm and pointed in white or coloured cement to match, laid over and including 10mm thick bedding layers in cement mortar 1:4 complete all as specified and directed

S&F 15 mm bore GI water tubing medium grade galvanised with all fitting complete etc fixed to walls, floors and ceiling complete all as specified and directed

Ditto as per item No 29.00 above but 20 mm dia bore complete all as specified and directed

S&F 20 mm dia stop valve ,cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed down both ends for iron pipe or for brass ferrule complete all as specified and directed

S&F Bib tap chromium plated, fancy type cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F Angle stop cock, cast copper alloy brass chromium plated with CP cup 15 mm bore complete all as specified and directed

S&F 15 mm CP brass pillar tap with capasten head screwed down high pressure with or without lettered "HOT" or "COLD" with long screwed for iron pipe complete all as specified and directed.

S&F Vitreous china wash hand basin, white flat, size 550 x400 mm incl CI brackets, CP brass waste coupling and PVC waste pipe complete all as specified and directed .

S&F soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S& F PVC connection 15 mm size with PTMT nuts and 45 cm long complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes any length and in any position complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes any length and fixed in any position(with clamps in wall) complete all as specified and directed.

S&F PVC (SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia complete all as specified and directed.

S&F PVC (SRW) vent cowl for 75 mm dia PVC pipe complete all as specified and directed.

S & F Rotational moulded polythelene, double layered, water storage tanks of capacity 1000 litres (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, including supply and fixing of 20mm bore brass float valve complete all as specified and directed.

M&L for 75 PVC (SWR) floor trap, plain with grating, jointing with solvent cement complete all as specifiied and directed.

M&L for preparation of undecorated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of apperture 1.18 mm fixed with tinned tack or galvanised wire stapples complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqmm each pan complete all as specified and directed.

M&L for 10 mm thick plaster in cement mortar 1:4 as in roof mixing with water proofing compound by 3% by weight of cement or as per manufacturers complete all as specified and directed Note :- Water proofing compound will be measured and paid seperately.

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning the surfaces complete all as specified and directed .

M&L for APP based polymeric membrane minimum weighing 3.50kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M&L for Applying two coat of btuminous aluminium paint all as specified and directed .

M&L for brick work with fly ash bricks , straight or covered on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified And directed.

Material and labour, 18-20mm thick granite ( of any type) work (table rubbed and polished ) in window cills, cooking plateform, shelves and the like, over and including 15mm thick screed bed in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

S&F in repair in fancy type brass CP hot and cold centre hole wash hand basin mixture swan neck, 15 mm bore screwed down high pressure with long screwed shanks and fly nuts screwed to iron pipe complete all as specifieed and directed. MAKE :- Pearl Cat part No ARI-013, PRAYAG-LAGUNA -9350.

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, 100 mm, ISI marked, complete all as specified.

Supply and fix 100mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

M&L for factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

M&L for factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S & F for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4, including removal of rubbish outside MoD land, complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in surface channel and drains complete all as specified and directed.

S&F interlocking stable rubber over floor (min dimension 1800x1200x20 m,tensile strength minimum 3.5+/- 0.5 MPA or 25 kgf/cm2 elongtion at break % minimun 200% density minimum 1.2g/cc as bedding of horses complete all as specified and directed.

M&L for 100 mm thick plain cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregates as in sub base of floors complete all as specified and directed.

M& L for sand filling in floors or pavings, laid in layers n exc 15 cm thyick, spreading,levelling,well ramming and watering complete all as specified and directed.

M& L for precast cement concrete, coloured, prepolished decorative interlocking paver block, Grade M-40, 80 mm thick any shape and size as approved in floor,pavement,approach,road side berms etc laid over sand cushioning,laid dry to the profile including vibrating with surface vibrator after laying including bedding and filling joints etc with grey cement and pigment complete all as specified and directed .

Earth filling under floors with excavated soil incl,spreeding levelling in layers n.exc 25 cm thick each and well ramming including water as required and removal of the excavated materials. Note :- Earth from excavation used for earth filling as per direction of Engr in Charge

M&L for damp proof course 40mm thick in PCC 1:2:4 type B0 with incl WPC @ of 3% of cement weight to horizontal or vertical surface including necessary formwork complete all as specified and directed. Note :- WPC shall be measured and paid seperately under respective item of BOQ

M&L for 15 mm thick cement plaster in cement mortar 1:4 on brick work or concrete surfaces finished even and fair. complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of exterior weather coat APEX paint over a coat of primer on plastered surface of wall and complete all as specified and directed.

M&L for three coats of oil bound distemper on newly plastered surface or unplastered surfaces of celling including preparation surface complete all as specified and directed.

S&F non skid vitrified tiles 10mm thick (square/ rectangular) area of each tile n.exc 0.36 sqm, in floors etc.set and jointed in neat cement slurry @ 3 Kg per SQM and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. Note : Colour and pattern will be as approved by GE

S&F double charged (coloured) virified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces. set and jointed in neat cement slurry @ 3 Kg per Sqm and pointed in white or coloured cement to match, laid over and including 10mm thick bedding layers in cement mortar 1:4 complete all as specified and directed Note : Colour and pattern will be as approved by GE

S&F 15 mm dia stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed down both ends for iron pipe or for brass ferrule complete all as specified and directed

S&F vitreous china table top wash hand basin, white flat, size 550 x 400x 160mm incl fixing on top surface, drilling and making hole and connected necessary wk, CP waste coupling, CP grating and CP bottle trap complete all as specified and directed by Engineer - in - Charge. (Make - CERA CAMPA Cat No S2020101 OR equivalent sample as approved by GE)

S&F looking mirror 5MM thick of size 700 mm x 500mm with double coat protection and longetivity, grounded edges for safety and silver plating on back side for better reflection and fixed to wooden plugs with chromium plated brass screws and cup screws complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F vitreous china bowl type urinal flat back size of 365X335X670mm with CP self closing angle cock 15mm for urinal with wall flange and 300mm connection pipe, CP grating and union along with discharge pipe complete all as specified and directed

S&F for powder coated aluminium sliding glazed window with three track / shutter, three shutter sliding with following specification complete all as specified and directed. (i) Window frame of cross section 101 mm x 44mm x 1.5mm thick (ii) Three way track for sliding shutter of cross section 91.8 mm x 31.75mm x 1.1mm thick (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick (iv) 4 mm thick tinded glass supeiror quality (v) IDPE rubber gasket for fixing of glass (vi) Locking cleats per shutter 1 Nos (vii) Sliding rollers per shutter - 02 Nos (viii) Aluminium wire cloth 0.30 mm nominal dia of wire and average width of aperture 1.56 for shutter 1 No (ix) Fixing of screw for frame with wall per window -08 Nos (x) Aluminium grill

S&F 10mm thick toughned glass urinal partition with S/S hinges fixing with the wall and at site as specification complete all as specified and directed

S&F 10mm thick toughned glass door partition with S/S hinges full ht of glass whith 180 degree swinging glass allows to door open inside and outside including CP handles inside and outside and fixing with the wall and at site as per specification complete all as specified and directed

S&F aluminium anodised tower bolt ,anodised ,length of bolt 150 mm complete all as specified and directed

S&F aluminium anodised tower bolt ,anodised ,length of bolt 150 mm complete all as specified and directed

M&L for cement concrete 1:3:6, type C2 using 40 mm graded stone aggregate in concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and directed

M&L for 150mm dia salt glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50kg cement, surface finsihed even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid separately.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 for manholes complete all as specified and directed.

M&L for cement concrete 1:2:4, type B0(12.5mm graded stone aggregate) as benching, coping, including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed

M&L for construction of Soakage well, excavated in ordinary soil, foundation PCC 1:3:6, walls of honey combed and solid brick in CM 1:4 , RCC cover slab in M-25 design mix, filling work with brick bats including intercepting chamber, screen chamber complete of size 2.4m dia x 4.5m deep as directed by directed by Engr-in-Charge. Drg No Ref TD HQ CEBZ Drg No TD/309 sheet 1/4, 2/4, 3/4 & 4/4.

M&L for construction of Soakage well, excavated in ordinary soil, foundation PCC 1:3:6, walls of honey combed and solid brick in CM 1:4 , RCC cover slab in M-25 design mix, filling work with brick bats including intercepting chamber, screen chamber complete of size 2.4m dia x 6.0 m deep as directed by directed by Engr-in-Charge. Drg No Ref TD HQ CEBZ Drg No TD/309 sheet 1/4, 2/4, 3/4 & 4/4.

M&L for Construction of septic tank for 50 users with sludge chamber including necessary earth work, brick work in CM 1:4 and precast RCC cover slab in M-25 Design mix complete all as specified and shown on drg No TD-217 sheet 1/7 to 7/7 and directed.

Cutting of grass, growth/vegetations, bushes or like and similar work and making the workable space for cleaning for carrying out cleaning of sewage line/manholes in any location or condition etc all as specified and directed by Egnineer - in - Charge.

M&L for DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid on 150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional for depth upto 0.70m to 1.65m incluidng returning and filling of excess soil and depositing where as directed making good complete all as specified and directed .

Demolition of Brickwork or stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:4 but except bricks complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster any description on brick or stone wall/ceiling etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed .

Dewatering of Septic tank soakage well and manhole of any depth in any position by pumping out and removing outside Military/Defence land by mechanical means (trolley mounted) and burying in pits all as directed including digging of pits in any type of soil and covering pits with earth after absorption of water and including providing and spreading required quantity of bleaching powder around the pit or dispose of waste material as per state protocol and washing the top of septic tank & soakage wells and surrounds with fresh water and sprinkling lime to make hygeinic complete all as specified and directed .

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed .

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and forming benching as required. Internal dia of pipe 150mm complete all as specified and directed .

Demolition of reinforced cement concrete complete all as specified and directed .

M&L Precast reinforced cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in manhole cover complete all as specified and as directed .

Dismantling of cast iron ,PVC or reinforced concrete drain pipes, 75/110/150/200 mm dia, jointed in cement mortar and taking out of trenches, walls if required, complete all as specified and directed.

S & F stack clamp out of 50mm by 5mm flat iron & 16mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 110mm nominal bore pipe complete all as specified and directed.

S & F stack clamp out of 50mm by 5mm flat iron & 16mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof for 75 mm nominal bore pipe complete all as specified and directed.

S & F 75mm bore PVC (SWR) junction single (Single T) equal or unequar of any radius, complete all as specified and directed

S & F 110mm bore PVC (SWR) junction single (Single T) equal or unequar of any radius, complete all as specified and directed

S & F 110mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including trap set complete all as specified and directed.

Dismantling AC sheet corrugated or semi corrugated sheet inc. ridges of any description as in roof and including removal from the site complete all as specified and directed Note: Work is in patches and directed by Engr-in-Charge and ht of bldg can be more than 10 meters.

S&F pre-painted galvalume aluminiun zinc coating GI corrugated steel sheet .50mm thick of approved colour having tensile strength of 550mpa as in roof covering cladding to wall fixed with self tapping screwes complete all as specified and directed Note: Work is in patches and directed by Engr-in-Charge and ht of bldg can be more than 10 meters

S&F pre-painted galvalume aluminium zinc coating GI based plain sheet .50mm thick of approved colour having tensile strength of 550mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed Note: Work is in patches and directed by Engr-in-Charge and ht of bldg can be more than 10 meters

S&F plain FRP sheeting 4mm thick at north light curves, roofs, windows, duct covering or at any other location by coach screw and washer, nut & bolt, staple pins or any other sutiable means all as specified and decided by engg-in-charge.Note: Work is in patches and directed by Engr-in-Charge and ht of bldg can be more than 10 meters

Dismantiling timber scantlings 40 sqm and over cum in section in any position unframed work complete all as specified and directed

S&F rolled mild steel plate girder or single stanchions built of one beam or channel section with flange plate , caps , bases, spices , angle bracket , cleats and other connection Fe-290 (Gde 165) as specified to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed Note :- ht of bldg can be more than 10 meters

S&F mild steel work in tubular pipe in railing including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

S&F mild steel Fe - 290 (Gde E- 165) for Framed work as in doors , chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, support to velley gutters, winties for roof sheets, framing for monkey proofing, welded mesh of pitch as decided by engg-in-charge, support to sign board & fencing post, etc. as specified to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

M&L for concealed point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, Fire Retardant, conforming to IS: 694-1990 PVC insulated, sheathed copper conductor cable in and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunken zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, sheathed and connected to common earth and earth dolly including cutting holes in or through the walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as directed for One light/bulb /exhaust/fan/street light point wiring controlled by one, one way switch/bell push button.

All as per Srl item No 119.00 above but one out let socket point 3pin 5 amps on independent board complete all as specified and directed.

All as per Srl No 119.00 above but on the same board with other switches complete all as specified and directed.

All as per Srl No 119.00 above but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one ,15/16 Amp socket outlet point on independent board complete all as specified and directed.

All as per Srl No 119.00 above but with 4 Sqmm nominal cross sectional area copper conductor cable and with 4 sqmm copper conductor earth wire for one 20 Amp socket outlet point on independent board complete all as specified and directed.

S&F switch piano flush type, 5/6A, AC, 240V, one way ISI marked complete all as specified and directed.

S&F switch piano flush type,15/16A, AC, 240V, one way ISI Marked complete all as specified and directed.

S&F Bell Push, Flush type, 5/6A, AC, 240V, ISI Marked complete all as specified and directed.

S&F socket piano flush type, 5/6A, 5pin, AC, 240V ISI Marked complete all as specified and directed.

S&F socket piano flush type 3 pin 5/6 Amp,3 pin , 15/16A,( two in one multipurpose ), AC, 240V ISI Marked complete all as specified and directed.

S&F lamp holder, PVC / Polycarbonate type with batten back plate, AC, 240V, Pin type, ISI marked complete all as specified and directed.

S&F Ceiling rose surface Bakelite 65x50mm, 3 terminals, AC, 240V, ISI Marked complete all as specified and directed.

S&F LED lamp 9/10 watts complete all as specified and directed.

S&F LED tube light fitting surface mounting, CRCA batten decorative box type , 4 feet, 240V, 20 Watt, including T-5 poly carbonate diffuser type 20 watt rectrofit tube rod complete all as specified and directed.

S&F LED tube light fitting surface mounting, CRCA batten decorative box type , 2 feet, 240V, 10 Watt, including T-5 poly carbonate diffuser type 10 watt rectrofit tube rod complete all as specified and directed.

S&F XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 25 sqmm 4 core complete all as specified and directed.

S&F XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 10 sqmm 2 core complete all as specified and directed.

M&L for clean fine dry river sand in trenches for cushioning of under ground cable/ cable duct complete all as specified and as directed. Note: Only punned thickness shall be measured for payment purpose.

M & L for fly ash brick protection length of brick shall be laid across the length of cable complete all as specified and directed.

S&F GI light grade tubing 40mm dia laid in trenches, road crossing , pasing through pipe or laid in wall/pole complete all as specified and directed.

S&F GI light grade tubing 25mm dia laid in trenches, road crossing , pasing through pipe or laid in wall/pole complete all as specified and directed.

S&F 25mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as directed .

S&F sheet metal enclosures double door for DB's with 200 Amps rated busbar and IP-43 protection with metal double door 8 way, SPN and flush to wall including all cutting on wall and making good to match the existing surfaces complete all as specified and directed.

S&F MCB single pole 240 volt , C series capacity 6 to 32 amps 10 KA and making connection complete all as specified and directed.

S&F isolator double pole 240 volt , B series capacity 40 amps 10 KA and making connection complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to centre both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1, for pit cover including testing on completion complete all as specified and directed.

S&F Exhaust fan made of steel body complete with louvers shutter, voltage 230V, RPM 1200, copper winding of sweep 250mm complete all as specified and directed

S&F Exhaust fan made of steel body complete with louvers shutter, voltage 230V, RPM 1200, copper winding of sweep 300mm complete all as specified and directed

Supply and fix Water heater storage type, electric and installed of capacity 25 ltr ISI marked BEE 5 star rating including providing of hold fast in wall and PVC connection 60 cm long with 15 mm dia brass union at both end heavy duty complete all as specified and derected by Engr-in-charge. Make : Recold / Venus / Havells

Supply and fixing 1x35W LED Building security light energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security light brackets of 25 mm dia GI pipe medium grade upto 1.4 mtr long bend to shape at 100-120 degree including flat iron clamps 32 x 4 mm -02 No and Suitable nuts and bolts grouted in wall including all material required for fitting complete all as specified and directed

Supply & fix BLDC Ceiling fan with blades,down rod, electronic regulator and accessories etc , Energy Saving , 1200mm sweep, minimum air delivery 210 CFM with service value 6.0 , BEE 5 star rated , AC, 230V complete all as specified and directed

S&F wall mounted fan single phase, electric driven, AC 230 volts of size 300 MM sweep complete with all accessories all as specified and directed.

S&F sheet metal enclosure factory fabricated with single pole & neutral with a two pin and earth plug top and socket complete with one single pole MCB 20 amps 240 volts complete all as specified and directed.

S&F sheet metal enclosure double door, VTPN DB, IP-43 protection, incomer MCCB type, 415 V, 4 way with 250 amps rated bus bar and flush to wall including all cutting on wall and making good complete all as specified and as directed.

S&F MCCB 4 pole 125 Amp 36 KA, 415 volts, 50 Hz, type DPX, frame size 125 with adjustable thermal & magnetic release complete all as specified and directed.

High Tech Metal India

A.V. ASSOCIATES