SPECIAL REPAIR TO CERTAIN SMQS AT AF STATION BHISIANA UNDER GE (AF) BHISIANA (PHASE II)

Amount

Taking down cement or cement lime plaster of any description and any thickness on brick, concrete or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Material and labour for rendering 15 mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces and finishing the surface even and fair etc. complete all as specified and directed.

Material and labour for rendering 12 mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and fair etc complete all as specified and directed.

Material and labour for rendering 5 mm thick cement plaster in CM (1:3) on fair faces of concrete surfaces in ceiling complete all as specified and directed.

Material and labour for rough cast plaster on brick wall consisting under coat of cement and sand mortar (1:4) not less than 10mm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel mixed with coarse sand and cement in the ratio 1:1:1 shall be applied and finish even complete all as specified and directed.

Material and labour for complete removal of existing treatment from wall upto plaster surface by electric sand paper grinder, washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper complete all as specified and directed by Engr-in-Charge.

Material and labour for applying two or more coats of premium quality exterior emulsion paint over old/new plastered/unplastered surfaces of walls, pillars, cornices including priming coat of exterior primer complete all as specified and directed.

Material and labour for applying one coat of premium quality exterior emulsion paint over and after preparation of old decorated plastered/unplastered surfaces of walls, pillars, cornices by brooming down etc complete all as specified as directed.

Material and labour for prepration of new plastered surfaces of ceiling and applying three coats of white wash on ceiling complete all as specified and directed.

Material and labour for complete removal of existing treatment and preparation of old plastered /unplastered surfaces of ceiling and applying two coats of white wash on ceiling complete all as specified and directed.

Material and labour for prepration of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed.

Material and labour for complete removal of existing treatment and preparation of old plastered /unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper acrylic/distemper oil emulsion acrylic, white or tinted over a coat of primer of same make complete all as specified and directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coats of oil bound distemper acrylic /distemper oil emulsion acrylic, white or tinted over a priming coat of same make on wall surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying 1-2 mm thick wall care putty on walls, including making surface even and smooth using sand paper before applying priming coat complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position, cut as required to facilitate demolition complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position (other than ground floor) in beams, staircases, landing chajjas and similar work complete all as specified and directed.

Material and labour for reinforced cement concrete type-B-1, (1:2:4 ) 20mm graded aggregate as in roofs, floors, kitchen platform, beams,lintels, Columns, shelves, staircase, landing, parapets and railings and with similar suspanded works including necessary form work required at site and applying a coat of cement slurry over old surfaces of concrete to make perfect binding, complete all as specified and directed at site.

All as per srl item no 18 above but as in chajjas complete all as specified and directed.

Material and labour for formwork to chullah hoods, shelves, chajjas, troughs and similar items in flats including edges complete all as specified and directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 10 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished concrete surface complete all as specified and directed.

Material and labour for mild steel TMT bars 8 to 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for mild steel TMT bars 6 to 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply and fixing of chicken wire mesh / hard drawn wire fabric of weight not exc 4 kg per sqm, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Demolition of cement concrete unreinforced of any description in any position not exceeding 150 mm thick (below or above ground level), complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection finishing cement concrete surface even and fair without using extra cement, including making construction joint at a interval not exceeding 3.00 m and at each corner and filled with sealing compound with grade A (normal) in 25/30, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specifed and directed.

Material and labour for 25 mm thick cement concrete type B-1 (1:2:4) (20 mm graded stone aggregate), as in sub base of floor, complete all as specified and directed.

Material and labour for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. including 15mm thick screed bed in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Material and labour for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) size of each tiles 600 x 600mm, premium quality tiles, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) for laying floor finishes complete all as specified and directed.

Material and labour for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) size of each tiles 600 x 600mm, premium quality tiles, on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in CM 1:4 to receive vertical tiles complete all as specified and directed.

Material and labour for Glazed ceramic coloured tiles in vertical surface 300 x 450 x 7mm thick including 10mm thick cement plaster in CM 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar, complete all as specified and directed.

Material and labour for Granite (of any type) work table rubbed and polished 18-20 mm thick machine cut, in steps, jams, pillars, window cills, cooking platforms and like laid and bedded over 15 mm thick cement mortar in CM (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including making 01 x hole for gas pipe in each cooking platform complete all as specified and directed.

Rounding the edge of stone slabs one edge such as in steps, cooking platforms, and the other simmilar situation, complete all as specified and directed.

Material and labour Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 15mm thick screed bed of CM 1:4 including rubbing and polishing complete all as specified and directed.

Material and labour for Machine cut kota stone slab 18-20mm thick in riser of steps ,skirting, dado and pillar laid over cement screed and cement slurry including 10mm thick cement plaster in CM 1:3 to receive kota stone and jointed rubbing and polishing complete all as specified and directed.

Demolition of cement concrete (un-reinforced) exc 15 cm thickness but above ground floor, sunken floor, complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:3) as in sunken portion walls and floor, mixed with water proofing compound 3% by weight of cement, finishing surfaces even & smooth without using extra cement complete all as specified and as directed. (Note :- Water proofing compound shall be measured and paid under appropriate item of this Sch ‘A’.)

Supplying only integral water proofing compound mixed as per instruction given over it, complete all as specified and directed as per manufactures direction.

Material and labour for bitumen hot blown any grade, applied hot, in two coats to concrete surfaces at the rate of 1.5 Kg per Sqm per coat, including cleaning of surfaces complete all as specified and directed.

Material and labour for laying 50 micron polythelene film, black in floors of sunken, complete all as specified and directed.

Material and labour for PCC (1:5:10) type E-2 using 40mm graded stone aggregate as in filling of sunken floor and mass concrete complete all as specified and as directed.

Material and labour for 50 mm dia GI spought pipe fixed in sunken floors by means of cutting holes in wall/ taking down old unserviceable pipe, fixed and beded in cement mortar/ PCC (1:2:4) and making good the disturbed portion of wall, complete all as specifed and directed.

Dismantling cast iron or reinforced concrete pipes, floor/walls up to 100 mm bore jointed in cement mortar and taking out, complete all as specified and directed.

Supply and fixing of 100 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, laid in trenches complete all as specified and directed.

Supply and fixing of 75 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, laid in trenches complete all as specified and directed.

Supply and fixing of 100 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed.

Supply and fixed of 75 mm bore cast iron soil waste and vent pipes, sand cast pipe, in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed.

Supply and fixed in repair cast iron 'P' or 'S' trap 100 mm bore, complete all as specified and directed.

Supply and fixed in repair cast iron socket (double collar), 100 mm bore, complete all as specified and directed.

Supply and fixed in repair cast iron socket, 75 mm bore, complete all as specified and directed.

Supply and fixing in repair cast Iron 100 mm bore branch piece single, (equal or unequal) single with acces door, ordinary or inverted (spigot or socket type) or with parrallel branches, with oval access door, complete all as specified and directed.

Supply and fixed in repair cast iron bends, 100mm bore, (any radius), disiminishing pieces or tapper (larger bore measured) with oval asses door, comlete all as specified and directed.

Supply and fixed in repair cast iron bends, 75 mm bore, (any radius), disiminishing pieces or tapper (larger bore measured)with oval asses door, comlete all as specified and directed.

Supply and fixed in repair cast iron 75 mm bore branch piece single, (equal or unequal) single with acces door, ordinary or inverted (spigot or socket type) or with parrallel branches, with oval access doors, complete all as specified and directed.

Supply and fixed in repair for 75 mm cast iron floor trap with SS grating 100 to 125 mm dia, including jointing with solvent cement, joint to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

Supply and fixed in repair stack clamp for 75 mm bore pipe out of 50 mm by 5 mm flat iron and 16 round round iron stay including bolt and nuts and securing ends of stay to walls or roof, complete all as specified and directed.

Supply and fixed in repair stack clamp for 100 mm bore pipe out of 50 mm by 5 mm flat iron and 16 round round iron stay including bolt and nuts and securing ends of stay to walls or roof, complete all as specified and directed.

Supply and fixing of 110 mm bore PVC (SWR) pipes (Medium duty) single socketed in any length with rubber ring joints fixed to walls/floor with and including clamps, nut bolts including dismantling of old outlet pipe etc. complete all as specified and directed.

Supply and fixing of 75 mm bore PVC (SWR) pipes (Medium duty) single socketed in any length with rubber ring joints fixed to walls/floor with and including clamps, nut bolts including dismantling of old outlet pipe etc. complete all as specified and directed.

Supply and fixing of 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

Supply and fixing of 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

Material and labour for providing precast cement concrete cover slabs using cement concrete type B-1 (1:2:4), 20 mm graded aggregate, (for manholes etc) and simillar works, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Material and labour 15 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Fixing only 15 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Material and labour 20 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 20 mm dia steel tubes any grade to walls and ceilings or laying in floors, including new fittings as required, complete all as specified and directed.

Material and labour for cutting chases, pining in making good to facing where required and pointing in cement mortar 1:3 for concealed water tubing, cutting not exc 10 cm girth, complete all as specified and directed.

Dismantling PVC water tanks exc 250 Ltr and n exc 500 Ltr and removing to store complete all as specified and directed.

Material and labour for three layered white colour Rotational moulded polyethylene water storage tanks of 500 ltr Capacity (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I complete all as specified and directed.

Material and labour for 20mm Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed as in repairs, complete all as specified and directed.

Material and labour for Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed Screwed both ends for iron pipes or for union and fixed in repair to 20mm dia of pipe, complete all as specified and directed.

Material and labour for Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed screwed both ends for iron pipes or for union and fixed in repair to 15 mm dia of pipe, complete all as specified and directed.

Material and labour of Vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests complete including provision of lime concrete bedding fixed as in repairs, complete all as specified and directed.

Supply and fixing of sheet glass shelf assembly consisting of 5.5mm thick sheet glass corner shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fixing of PVC valveless, syphonic action type, flushing cistern, low level ,white, with inlet, ball valve, float and handle,complete with flush pipe of polythelene of low or high density or PVC 32 mm dia, including brackets / fastening assesories of 10 litres capacity, fixed in repair, complete all as specified and as directed.

Supply and fixing in repair for mirror cabinet of min size 430x330 mm with openable door shutter as approved by GE complete all as specified and directed.

Supply and fixing of Vitreous China wash basin, white, flat back, size 550x400 mm fixed on brackets or stands, including 32 mm waste coupling of PTMT (half or full threaded)/ CP Brass and corrugated waste pipe with adopter of 900 mm long, fixed in repair complete all as specified and as directed.

Supply and fixing in repair wash hand basin, brass CP mixture 15mm bore for mixing hot and cold water screwed down for 15 mm iron pipe and fixed, complete all as specified and directed.

Supply and fixing in repair 15 mm dia bore CP angular stop cock with wall flange cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair 15 mm dia bore CP concealed stop cock cast copper alloy chromium plated with long shank, fancy type, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of Aqua guard nozzle tea valve fixing with 15mm bore GI pipe complete all as specified and directed.

Supply and fixing in repair PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fixing in repair PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.

Supply and fixing in repair, 15 mm dia Bib taps, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

Supply and fixing in repair brass CP Wall mixer 3 in 1 with arrangement for overhead shower bend, 15 mm bore, for mixing hot and cold water, screwed down for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repair 15mm bore wall mounted goose neck sink mixer ( Hot and Cold) with provision of swivel arm, connecting legs and wall flanges, complete all as specified and directed.

Supply and fixing in repair Brass Chromium plated shower rose 125 mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

Supply and fixing in repair stainless steel soap dish of size 115 x 85mm, complete all as specified and directed.

Supply and fixing in repair Brass CP tubular towel rail of 20 mm dia, D type ,60 CM long between flange complete all as specified and directed.

Supply and fixing of stainless steel towel ring round/ square with cap, with fixing screws complete all as specified and directed.

Supply and fixing in repair sinks made of stainless steel 1mm thick kitchen or labo-ratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, including 40 mm bore dia CP waste coupling (half/ full threaded with 900 mm and PVC waste pipe min 900 mm long complete all as specified and directed.

Supply and fixing in repair Kitchen Plate rack with of size 750x600x250mm of stainless steel complete all as specified and as directed.

Suply and fixing of coat hooks of six pegs made out of stainless steel 45 cm long (as per sample), complete all as specified and directed.

Dismantling of boarding in any position and in any description fixed with nail, complete all as specified.

Supply and fixing of 18 mm thick PVC ply of Plain color fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer‐in‐Charge.

Supply and fixing of 18 mm thick PVC ply of one side Prelam/ Rigidlam and other side balancing laminate colour to make kitchen cabinet Shutter/ drawer Front shutters complete as per specifications and as directed by the Engineer‐in‐Charge.

Supply and fixing of 5 mm thick PVC ply of plain white colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet back covering and pull out drawer base complete as per specifications and as directed by the Engineer‐in‐Charge.

Supply and fixing for 20mm wide and 1mm thick PVC edge bedding of PVC pested on edges with suitable adhesive, complete all as specified and directed.

Supply and fixing of Ball bearing runners 45 mm Telescopic Channel ( 20 Inch ) full extension load capacity 50 kgs, complete all as specified and directed.

Supply and fixing of stainless steel handles 100 mm size for kitchen cabinet shutters complete all as specified and directed.

Material and labour for continous piano hinges stainless steel, bright finish width of flaps when open 40 mm complete all as specified and directed by Engr-in-Charge.

Supply and fixing Hasp and staple safety type aluminium powder coated with mild steel pin inculding bolt to hinge plate and fix with screws 150 mm size of hasps and staples complete all as specified and directed .

Supply and fixing of Magnetic catcher for cupboards complete as all specified and directed by Engineer-in-Charge.

Supply and fixing in repair MS powder coated curtain Rods 18 to20 mm bore over doors and windows, with fixing MS powder coated brackets, including screws, rawal plug and PVC powder coated fineals / fancy type end bulbs at each end of curtains rod, any colour etc complete all as specified and directed.

Taking down Chowkhats or frames/ steel windows/ ventilators, not exc 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

Taking down shutter of area exc. 1 sqm but not exc. 2 sqm each complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing complete all as specified and as directed.

Material and labour for factory made solid panel PVC door shutter 30mm thick (stile), consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drg complete all as specified and as directed.

Supply and fixing 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed.

Supply and fixing of 125 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing of 100 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of steel window/ ventilator of box section having 1.25 mm thick CRC sheet frame with double shutter inside gauged shutter and outside glazed shutter with one nos steel handle in each shutter, one nos peg stay in each shutter, complete with glazing bars and 08 Nos of 10 x 10 mm square guard bars in equal spacing, devoited or welded as per sample including one coat of red oxide primer all as specified and directed.( The rates includes 4 mm thick plain sheet glass and galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and two coat of synthetic enamel paint over a coat of zinc chrome primer) Note : The design of window to be facilitated by cooler fixing provision where ever reuired) complete all as specified and directed.

Taking down chowkats and shutters without taking off shutters from the frame, size of opening exc. 1.50 sqm but not exc 4 sqm each complete all as specified and as directed.

Supply and fixing of Pressed steel frames of size 125 X 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

Supply and fixing of Pressed steel frames of size 105 X 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

Material and labour for PCC (1:3:6) type C-1 using 20 mm graded aggregate as in back of pressed steel chowkhats etc complete all as specified and directed.

Material and labour for PCC (1:2:4) type B-2 using 20 mm graded aggregate as in hold fast of steel chowkhat/ frames etc complete all as specified and directed.

Supply and fixing for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Supply and fixing for factory made, 35mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces using 2nd class HW as in rail and style. The size of rail and style as per IS-1003 (Part – I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

Supply and fixing of 35mm thick glazed and skelton shutter 2nd class hard wood, open rebated and prepare to receive glass, gauge etc. (without sash bars) edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of member of shutters as specified in SSR part-1, section 8, clause 8.24 (a) complete alla s specified and directed.

Taking down shutter of any description exc 1.00 sqm but not exc 2.0 sqm each and refixing in same opening after easing and adjusting (Chowkhat/ frame changed) etc, complete all as specified and directed.

Supply and fixing in repair 100 mm Butt hinges medium weight, cold rolled mild steel, fixed in repair complete all as specified and directed.

Supply and fixing 150 aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply and fixing 150 aluminium anodised barrel tower bolts of extruded section and fixed in repair tower bolt complete all as specified and directed.

Supply and fixing 300 mm aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing 300 mm aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed in repair complete all as specified and directed.

Supply and fixing 150 mm extruded aluminium alloy handles, fabricated type anodised, complete all as specified and directed.

Supply and fixing 150 mm extruded aluminium alloy handles, fabricated type anodised, fixed in repair handles complete all as specified and directed.

Supply and fixing floor door stopper of size 140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring ficed in floors complete all as specified and directed.

Supply and fixing mild steel 300mm ordinary rat tail rod pattern springs, including roller and roller plate fixed in repairs complete all as specified and as directed.

Supply and fixing in repair of aluminium body door cill upto 1mtr length at bottom part of door to stop entry of insect inside the room complete all as specified and as directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tack or galvanised wire staple complete all as specified and directed.

Supply and fixing in repairs galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and directed.

Material and labour applying two coats of synthetic enamel paint over a coat of pink primer including prepration of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth complete all as specified and directed.

Material and labour for preparation of old wooden surface and applying one coat of synthetic enamel paint complete all as specified and directed.

Supply and fixing Joist, channel, angle, or tee sections, fixed independently, without connecting plates, as in cooler stand etc. (cut to ordinary lengths i.e. within 20mm of the length indicated in Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer exposed to view surfaces complete all as specified and as directed

Material and labour for preparation of old steel surfaces of any description not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint over complete all as specified and as directed.

Taking down existing cement plaster/roof treatment including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

Material and labour for brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and as directed.

Material and labour for providing cement concrete type B-0 (1:2:4) 12.5 mm graded stone aggregate for providing slope, maintain level, roof kerbs or mud stops rounded or chamfered edges all as directed by Engr-in charge

Material and labour for 10 mm thick cement screed bed or beding layer / plaster in cement (1:4) mixed with water proofing compound on concrete roof surface, complete all as specified and directed.

Material and labour APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3 mm thick reinforced with polyster Non wove fabric (weight not less than 150 gms/sqm) laid over a coat of hot bitumen 85/25 @ 1.20 kg per sqm by torch application, including a coat of aluminium paint applied on membrane, complete all as specified and directed.

Material and labour for providing precast cement concrete louvres and jallies 25mm thick type B-0 (1:2:4 using 12.5mm graded aggregate), (measured solid), including all mouldings etc complete all as specified and ditected.

Demolition of Brickwork or stone/ boulder masonary, built in cement mortar or cement lime mortar complete all as specified and directed.

Material and labour for brick work with subclass B bricks, straight or curved on plan exc 6 m mean radius, buit in cement mortar (1:6) complete all as specified and directed.

Material and labour for brick work with subclass B bricks, straight or curved on plan to any radius in half brick thick wall, buit in cement mortar (1:4), complete all as specified and directed.

Taking down carefully copper / aluminium point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls roofs etc complete all as specified and directed.

Taking down carefully unserviceable DB's including MCBs of of any size make, type and capacity and making good disturbed surfaces of wallls/roofs etc complete all as specified and directed.

Supply and fixing of concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed cable 1100 volts grade drawn through and including non metallic rigid PVC conduit, medium grade minimum 19mm dia ISI marked and conduit accessories fixed concealed in wall/ceiling/roof etc with sunken type pressed steel/welded MS terminal boxes made out of 1.6 mm MS sheet, 3mm thick laminated sheet top cover for mounting of fittings, switches, sockets outlets, regulators etc complete including provisinion of 1.0 sqmm PVC insulated unsheathed cable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly complete all as specified and directed for the followings : (a) One light/fan point controlled by one switch 6 amp one way

(b) One bell point controlled by one switch 6 amp one way on same board with other switches or indepepent board one way

(c) One 3 pin socket 5 amp on the independent board.

(d) One 3 pin socket on same board with other switches.

(e) One light point controlled by two-2 way switch.

All as per Srl Item No. 154 above but point wiring with 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheathed cable 1100 volt grade and 1.5 sqmm PVC insulated and unsheathed cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on independent board.

Supply and fixing of modular white cover plate with frame, 1 module/ 2 module complete all as specified and directed.

Supply and fixing of modular white cover plate with frame, 3 module/ 4 module complete all as specified and directed.

Supply and fixing of modular white cover plate with frame, 6 module complete all as specified and directed.

Supply and fixing of modular white cover plate with frame, 8 module complete all as specified and directed.

Supply and fixing of modular flush boxes, 1 module/ 2 module complete all as specified and directed.

Supply and fixing of modular flush boxes, 3 module/ 4 module complete all as specified and directed.

Supply and fixing of modular flush boxes, 6 module complete all as specified and directed.

Supply and fixing of modular flush boxes, 8 module complete all as specified and directed.

Material and labour for modular switch, one way 6 amp, 1 module complete all as specified and directed.

Material and labour for modular bell push switch, 6 amp, 1 module complete all as specified and directed.

Material and labour for modular switch, 16 amp, 1 module with indicator complete all as specified and directed.

Material and labour for modular socket, 6A, 2/3 pin combined, 2 module complete all as specified and directed.

Material and labour for modular socket, 16 Amp, 6 pin, 2 module complete all as specified and directed.

Supply and fixing of modular fan step regulator, 120 W, 1 module complete all as specified and directed.

Supply and fixing of bell Ding dong AC 230Volts single pole complete all as specified and directed.

Supply and fixing of ceiling rose 65x17mm of three terminals PVC/ polycarbonate, isolated body complete all as specified and directed.

Supply and fixing of 1X18 watt wall mounted, new generation LED T-8 Retro fit for multipuspose application with LED Rod, made from exturded aluminium housing, polycarbonate diffuser including all fixing accessories & connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down complete all as specified and directed by Engr-in-Charge.

Supply and fixing of 1X10 watt wall mounted, new generation LED Batten fitting for multipuspose application with exturded aluminium housing with decorative end caps including all fixing accessories & connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down complete all as specified and directed by Engr-in-Charge.

Supply and fixing of LED bulk head light fitting with high output diffuser, 10 watt, 220 V AC with driver holder PDC housing with opal diffuser equipped with 2KV in built surge protection with IP-65 ingress protection rating complete with all accessories pre-wired and connecting electrically with ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site complete all as specified and directed by Engr-in-Charge.

Disconnecting electric connection and taking down carefully ceiling fans/walls fan/exhaust fan/Air circulator fan any sweep and removing fan and fan blades to AGE E/M store yard complete all as specified and directed by Engr-in-Charge.

Material and labour for painting of ceiling fan with two coats of white synthetic enamel paint and marked MES no by black permanent marker complete all as specified and directed by Engr-in-Charge.

Material and labour for painting of exhaust fan with two coats of white synthetic enamel paint and marked MES No by black permanent marker all as directed by Engr-in-Charge.

Hanging/fixing ceiling fan of any sweep to same site after repair/servicing including flexible cable from ceiling rose to fan complete all as specified and as directed by Engineer-in-Charge.

Fixing only exfaust fan of any size to same site after repair/servicing including flexible cable from ceiling rose to fan complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of metal plug and socket single pole and neutral with a two pin and earth plug and socket alongwith one single pole MCB of 20 Amp concealed in wall complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully copper / Aluminium wiring and removing materials from site as directed and making good disturbed surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour submain wiring with two runs of copper conductor PVC insulated unsheathed cable 1100 volt grade 4 sqmm drawn through PVC conduit medium grade ISI marked 25mm dia as per IS specification fixed concealed in wall/ceiling including conduit and conduit accessories and including provision of PVC insulated 4 Sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distemper complete all as specified and as directed at site. Note : Two runs of 4 sqmm cable alongwith one run of 4 Sqmm PVC insulated unsheathed copper conductor as earth wire, conduit and conduit accessories will be measured as one length).

Material and labour submain wiring with two runs of copper conductor PVC insulated unsheathed cable 1100 volt grade 6 sqmm drawn through PVC conduit medium grade ISI marked 25mm dia as per IS specification fixed concealed in wall/ceiling including conduit and conduit accessories and incl provn of PVC insulated 6 Sqmm multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distamper complete all as specified and as directed at site. Note : Two runs of 6 sqmm cable alongwith one run of 6 Sqmm PVC insulated unsheathed copper conductor as earth wire, conduit and conduit accessories will be measured as one length).

Supply and fixing of MCB DB TPN 4 Way vertical type factory made IP 43 protection class metal double door with Shrouded Neutral Bar & Pan assembly with connecting link complete including fixing one MCCB 125A complete all as specified and as directed by Engr-in-Charge.

Supply and fixing of MCB DB SPN 8 Way factory made IP 43 protection class metal double door with 200 Amp rating bus bar 240/ 430V for fixing of MCBs/ Isolators/ RCCBs etc complete all as specified and as directed by Engr-in-Charge.

Supply and fixing of MCBs 240/415 Volts 10 KA finger proof terminal, B curve bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB complete all as specified and as directed by Engr-in-Charge for the following sizes : (a) MCB SPN 40 Amps. Note : DB will be measured and paid separately under respective items of Sch A, BOQ.

(b) MCB SP 5 to 32 Amps

Disconnecting electric and water connection connection and taking down carefully Geyser and deposited to AGE E/M store yard and refixing geyser at same location complete all as specified and directed by Engr-in-Charge.

Material and labour for Meter Box of size 0.75 MX0.60 M of 0.30 M width of MS Sheet of 3 mm thickness and a clamping or supporting sheet inside for suppoting of 4 Nos Meter and door with 1 Nos of transparent glass of 5 mm thickness suitable for visibility of 4 Nos meter fixed on door with suitable arrangemnets. There should be 8 Nos hole for entering of 25 mm dia pipe complete all as specified and directed by Engr-in-Charge. Note : (i) Drawing of meter box should be approved by GE . (ii) Meter box shall be fixed in wall and necessary chiseling and make good of wall should be included in quoted rate.

Disconnecting electric connection and taking down carefully energy meter and deposited to AGE E/M store yard and refixing energy meter in meter box with qtr no wrtitten on meter by Black permanent marker complete all as specified and directed by Engr-in-Charge.

Supply and fixing of MCCB 'C' curve, four pole, 125 Amps, 415 Volt, breaking capacity 10KA complete all as specified and directed by Engr-in-Charge.

Supply and fixing of bracket for street light fiting made out of 40mm dia GI pipe light grade 1.2 mtr long each bent to required shape and size as directed by Engineer-in-Charge and fixed to pole with and including flat iron clamps 02 Nos made out of 32 x 6mm flat iron including GI nuts, bolts & washer and painting of clamps and street light fitting bracket with one coat of red oxide primer, one under coat and one finishing coat with aluminimum paint complete all as specified and directed.

Supply and fixing of LED security light fitting 30 watt, having uniformity ratio 0.25, high pressure die cast aluminium housing, heat resistant toughened glass with frame, IP-66 protection complete with lamp & connected items and connection with suitable cable from ceiling rose to light fitting and fixing on GI pipe bracket made out of suitable dia GI pipe medium grade 1.2mtr long bent to shape and fixed on wall with flat iron clamps, nut, bolts, washer etc. complete all as specified and directed by Engr-in-Charge.

Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected to and including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES SSR Part - I and testing on completion including necessary excavation and earth work in any type of soil, PCC (1:3:6) type C-1 chamber, pre-cast RCC slab 50mm thick in cement concrete (1:2:4), type B-1, reinforced with welded steel wire fabric or XPM,(weight not less than 4 Kg per Sqm) with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe,15mm dia light grade, 7.5 mtr long for protection of earth lead upto test point etc complete all as specified and as directed by Engr-in-Charge.

M/s Kamal Builders

yogesh kumar contractor

M/s Luxmi Constructions