COMPREHENSIVE REPAIR AND DOOR TO DOOR WK FOR OFFR MD ACCN AT MOTIBAGH , PENTON RD, ROBERT RD, HUNTER RD, CASSEL ROAD, NAGARWALA ROAD AND CENTRAL INSTITUTE AREA OF AGE B/R-II UNDER GE (N) AHMEDNAGAR

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding/backing and removing all rubbish/dismantled material outside MD Land.

Demolition of plain cement concrete (unreinforced) in ground floor not exceeding 15 cm thick all as directed.

M&L Excavating over areas,n exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed by Engg-in-cgarge.

Removing excavated material exc.250m but n exc. 500m and deposited where directed.

M&L for moorum filling in floors or paving laid in layers n exe 15 cm thick spread leveled and rammed including watering complete all as specified and directed by Engg-in-charge

M&L for hard core of gauge etc 63 mm but n exc 100 mm deposited spread and levelled in layer n exc 15cm thick water and rammed etc complete all as specified and directed by Engg-in-charge

M & L for Cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and directed by Engineer-in-Charge

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

M&L for Glazed colour ceramic tiles 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for joint free / rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,(400x400)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free / rectified vitrified/ ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm,(600 x600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

M&L for Virified Ceramic tiles dark shade/Double charged/ultra charged 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm (600 x 1200)mm , in floors etc. laid over and including roughning existing surface, making good the damaged surface, levelling and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

-Ditto- as per item No 12 above but on skirting and backing coat of 10 mm thick in CM 1:4

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land. all as directed.

M & L for Chequred cement concrete tiles with pigment 25 cm x 25 cm x 25 mm thick, set, jointed and pointed in neat cement slurry as in floors over and including screed bed of 15 mm thickness in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engineer-in-Charge

M&L for 20mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs, lintel etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in CM 1:4 jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as directed.

M&L for 30 mm thick Rough dressed(shahabad) lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 as in floor/plinth etc over bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed

Fixing only 30-40mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed

M&L for heavy duty vitrified paver tiles 30cm x 30cm x 10mm thick,approved by GE withnset,jointed and pointed in neat cement slurry with grey cement and pigment to match in floors,over and including screed bed or bedding a layer of 15 mm in cement mortar 1:6 complete all as specified and directed by Engg-in-charge.

Demolition of plain cement concrete solid block masonary built in cement mortar & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed

M&L for rendering, 12 mm thick on stone surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 10 mm thick on brick/concrete surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed.

M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and smooth without using extra cement all as specified and directed.

M&L for 2 mm wall care putty on walls complete all as specified and directed by Engg-in-charge.

Dismantling of single layer manglore pattern in roofing & removing all rubbish/dismantled material outside MD Land.all as directed.

-ditto- as per Sr item No 29 above but bedded in cement morter

M&L for roofing tile, manglore pattern interlocking at sides joints laid dry

-ditto- as per Sr item No 31 above but except manlore pattern tiles

M&L Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement morter 1:6

Dismantling timber scantling 40 sqcm and over in section, in any postion framed work as in scanging of main joist of roof & removing all rubbish/dismantled material outside MD Land.

-ditto- as per Sr item no.34 above but in fillets,rails, posts, rafters purlins etc under 40 sqcm in section framed work & removing all rubbish/dismantled material outside MD Land.

Dismantling battens for tiles, shingles etc of any size including tilting fillets spacing exc 15 cm &removing all rubbish/dismantled material outside MD Land.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including ridge & removing all rubbish/dismantled material outside MD Land.all as directed.

M&L for second class hard wood in scantling of roof rafters, etc wrougt framed

S&F Pre-painted Galvalume sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

Supply and fix Pre-painted 0.50 mm thick plain, galvanised sheet in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge.

S&F of steel work in post,joist,channel,angle, or tee section fixed independently,without connecting plates etc as per Fe 410-W (Grade-E-250 quality-A)

M & L for filleting in any position in repairs and to any shape in cement and sand mortar (1:4) including all mitres, stops etc exc 25 Sqcm but n.exc 50 Sqcm etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed.

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.

Supply and fix in repairs wash hand basin vitreous China, flat back of size 550 X 400 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed.

M&L for preparing new unplastered or plastered surfaces and applying two coats of oil bound distemper including chalk whitening on wall including smooth roller finish complete all as directed.

M & L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffholding etc complete all as directed.

M&L for preparing old unplastered or plastered surfaces and applying one coats of oil bound distempering on walls all as directed.

--ditto-- all as per Sr item No. 48 above but two coat of OBD on old surface

M&L for preparing old painted surfaces of wall and applying two coats of cement based paint all as directed.

Preparing old painted surfaces of wall and applying one coats of cement based paint all as directed.

M & L for preparation of old plastered treated surface of walls by brooming down and apply one coats of wheather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as directed.

M&L for preparation of old surfaces of wood of any description exc 10cm width/girth incl cleaning applying one coat of synthetic enamel all as specified directed by Engineer-in-charge.

M&L for preparation of old steel and iron surfaces, of any description, over 10 cm width or girth not other wise described and applying one coats of synthetic enamel paint over a coat of red oxide primer

Taking down chowkats or frames exc 1.5 Sq m but nexc 4.00 sqm with shutters (without taking off shutters from the frames) all as directed.

Taking down chowkats or frames n exc 1.5 Sq m with shutters (without taking off shutters from the frames) all as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each all as specified directed by Engineer-in-charge.

Taking down shutters of any description n exc 1 sqm each all as specified directed by Engineer-in-charge.

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

Supply and fixing 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

Supply and fix 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed.

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face

Supply and fix galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm

Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 300mm long.

Supply and fix aluminium anodised barrel tower bolt of extruded section 200mm long.

Supply and fix aluminium anodised handles of extruded section 150mm long.

S&F in repair 300mm mild steel ordinary rat tail rod patteren door spring including roller and roller plate complete all as specified and directed

S&F in repair aluminium extruded section body door closer for aluminium door shutter hydraulically regulated,designation No 1 universal type,suitable for door shutter upto 700 mm in width and of weight not more than 35 kg and fixed.complete all as specified and directed.

S&F in repair 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and directed.

S&F in repair Cylindrical Latch Door Lock Tubular (Dumbell lock) stainless steel finish fixed in door complete all as specified and directed by Engg-in-charge. Make:Godrej,Europhia and equivalent.

M&L for two coats of synthetic enamel paint over a coat of pink primer for new wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces and smooth finish with roller all as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer for new steel surfaces of any description exc 10 cm width or girth including preparation of surfaces all as directed.

Supply and fix mild Steel 20 mm dia decorative powder coated curtain rods with fixing brackets fixed in repairscomplete all as specified and directed.

Supply and fix in repairs 32 mm dia PVC waste pipe(outlet pipe) plain fixed to waste coupling of WHB or Sink etc all as directed.

Supply and fix in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed.

S&F in repairs stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge .

S&F in repair wall mixture, with provn for overhead shower all as specified and directed by Engg-In-Charge

Cleaning the surface with wire brush,detecting sources of lea and removing/taking down unsound treatment/surface,proving material and labour for carrying out non-destructive water proofing treatment to sunken portion of slab,floor and walls of bath,WC,WHB and floor trap (combined unit) by using construction chemical method as hydrophobic PU grouting etc with first course of injection MDI based PU foam and second course of injection PU plain all as manufacturers instruction,etc,the PU foam shall have 100% solids and solvent free,and shall expand 30-40 times its volume at liquid stage in presence of water,the PU plain injection shall have minimum 100CPS visscosity and shore hardness minimum 50 complete all as specified and directed.Make:PIDILITE or equivalent

M&L for fixing the metallic packer for hydrophobic PU foam including making holes and sealer all as per manufacturers specification,the PU foam shall have 100 % solids and solvent free,and shall expand 30-40 times its volume at liquid stage in presence of water,the PU plain injection shall have minimum 100CPS visscosity and shore hardness minimum 50 complete all as specified and directed.Make:PIDILITE or equivalent. Note:This item is catered only for Material and labour by for fixing the metallic packer

M&L for the chemical cleaning of tile joints and re-grouting carefully by washing the existing tile with heavy duty tile cleaner preferably of M/S Pidilite or equivalent cleaner,again washing with fresh jet water,scratching the joints and filling the same with (white/matching colour) epoxy tile grout of M/S Pidilite,ROOF RTM epoxy or euivalent,curing,cleaning the surface etc as per the sample done at site complete all as specified and as directed.

M&L for false ceiling with vinyle faced Arn-GYP-FB, celing 600 x 600 x 7-8 mm thick with washable metallized polyster foil backing with vinyle covered edges supporting sections shall be of sutable size from same makes embossed on section and level adjuster duly suspended by 2mm dia GI wire fixed to roof at 600mm center to center as per manufactureres instruction and including taking down all as directed Make : Armstrong or equivalent in Saint Gobin/Lafarge

Supply and fix in repair health faucet (hand shower) with 8 mm dia 1 m long flexible tube wall mounted / hooked all as per

Supply and fix in repair bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule all as directed.

Supply and fixing in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore

Supply and fix in repair 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Supply and fix in repairs, shower rose with shower arm

Supply and fix 15 mm dia pillar tap(Swine neck), cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Hacking out old broken glass (any thickness size,quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads n'exc 1.5 Sqm.

M&L for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane all as directed.

Supply and fix in repair galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples all as directed.

Supply and fix in repairs rotational moulded polyethylene water storage tanks Tripal layer (cylindrical vertical with closed top) of 500 litres capacity hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to irin pipr and connecting complete all as specified and directed.

--ditto-- all as per Sr item No 95 above but 1000 ltrs etc.

S&F in repairs PVC connections 15 mm size with Stainless steel Nuts of length 600mm

S&F in repair for stainless steel grating without waste holes 100 mm dia

S&F in repair for stainless steel grating with waste holes 100 mm dia

S&F for PVC (SWR) floor trap, plain with grating including jointing with solevent cement 75 mm bore

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- as per Sr item No 101 above but as in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

.-Ditto- as per Sr item No 103 above but as in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F PVC (SWR) vent cowl110mm bore

S&F in repairs for low density polyethelene pipes 32 mm bore (LDPE) of pressure rating 6 Kg/cm² laid in trenches/fixed to wall

Supply and fix repairs 10 Ltr PVC valveless, syphonic action type, flushing cistern,low level, all accesories all as directed. Make :- Sleek essence series Of Hindware or Cat part No E8303 Of Parryware .

Taking up or down steel tubing and connections,15 mm bore

--ditto-- all as per Sr item No 113 above but 20mm bore

S&F of CPVC pipes SDR 11 including fittings in trenches, 16mm outer dia fixed to walls /ceiling or laid in trenches incl all necessary fittings.

--ditto-- all as per Sr item No 115 but 20mm outer dia etc

Supply and fix coloured anodised aluminium three track window made out of Jindal aluminium sections Nos 20671,20672,20690 & 20668 including 5 mm thick plaint sheet glass and stainless steel wire guaze as per PS, locking arrangement all as directed.

S&F coloured anodised aluminium ventilator as per PS and make approved by GE including all fittings locking arragement, glazing, guazing and fixed with suitable size of screws all as directed

Fixing only for framed work such as guard bars/ grill /gratings etc with ends of bars shouldered and/or riveted or gorged into spikes confroming to FE-290, Gde -E- 165

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in the same opening including easing and adjusting and also refixing builders hardware as required including renewal of unservieable screws etc

S&F in repair for 19/20mm PVC shutter Colour PVC prelaminated board fixed to timber frame worka as in cup boards shutters/shelves/pelmets box and similar items etc complte all as specified and directed by Engineer-in-Charge

S&F in repairs POP suspended ceiling using appropriate size tiles ( 10 mm thick ) support members using GI section of 26 gauge suspended by GIO holder from the slab/ beam in line and level as per design as approved finishing, cleaning and filleting side with suitable moulding, cleaning the site including taking existing etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs Solid PVC Wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement anf fixing at site on PVC frame as per specification and drawing inluding taking down/ out of existing wall panneling etc complete all as specified and directed by Engineer-in-Charge

S&F for in repiars Auto closing hinges 35mm of o crank (KH-001) ir 8 crank (KH=002) openable at 110 degree for kitchen cabinet shutters fixed complete as specified and directed

Supply and fix in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets etc complete all as specified and directed by Engineer-in-Charge

Supply and fix repairs PVC (SWR) floor trap, 75 mm dia with grating including jointing with slovent cement etc all as directed.

S&F in repair Brass Chromium Plated toilet paper holder fixed with (CP) brass screws of approved quality.

S&F in repairs PVC Seat Cover with hinges complete all as specified.

S&F in repairs decorative towel ring recangular chromium plated fixed with (CP) brass screws of approved qualityas specified

S&F in repairs Soap Dish wired type including necessary fitting material screws etc complete all as specified.

S&F in repairs looking mirror of size 600 mm X 450 mm etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs corner glass shelf 200mm size

S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . /25mm-455gms/ 40mm - 690 gms) complete al as directed.

S&F in repair 25mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . /25mm-455gms/ 40mm - 690 gms) complete al as directed.

M & L for providing water proofing treatment on roofs, as per manufacturere's instructions and as specified after taking down/out as existing out at site etc complete all as specified and directed by Engineer-in-Charge (a) Cleaning the newly plasterd surfaces with wire brushes and applying a bituminous primer @ 0.30 l/sqm & surface shall be allowed to dry. (b) Applying and laying torch APP polymer modifiedbituminous membrance 3mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by therofusion process as per manufacturers specification including applying one coat of aluminium paint Make : Super Thermolay of STP or equivalent in TEXSA India Ltd / IWL Ltd / Tiki Tech

M&L for plastering 10 mm in cement and sand mortar (1:3) using 100 % course sand on roof mied with and including WPC @ 3% by weight of cement and finished the surface even and smooth without using extra cement.

Day to day complaints for the following works :-

(a) Complaint related to carpenter works like door easing, door repair, kitchen cup board repair, window/door wire mesh/glass pane repair, refixing of building hardware etc by deploying carpentor and mazdoor.

(b) Complaint related to plumbing works like repair/refixing of Bib tap, Stop cock, Angle cock Connection pipes, waste pipes, Flush tank, Flush pipe,Shower, Pvc tank, ball valves, towel rail ,WHB,EWC, waste coupling, Grating,Pillar tap etc.by deploying plumber and mazdoor.

(c) Complaint related to cement works like repair to floors/ wall plaster in patches/ filling of holes, tiles repairs etc. by deploying mason and mazdoor.

(d) Removing blockage from water closet,floor or gully or Nahani trap and bends by rodding thoroughly and pouring water under pressure and cleaning,clearing the drainage to efficient and smooth flow of sludge/waste water all as specified and directed by Engg-in-charge.

Notes for Ser item Nos 137 (a) to 141 (d) :-The quoted rate of contractor shall comprise the following :-

(a) Contractor shall provide sufficient skilled and unskilled manpower on requirnment basis as directed by engineer incharge for attending and completing the complaints as per the users satisfaction. However, the number of skilled and unskilled manpower shall be increased as directed by Engr in charge depending upon the requirement / number of complaints registered at the complaint center. In case of failure on providing suffiiciet manpower by the contractor, a penalty at the rate of Rs 1000 per skilled person per day and Rs 600 per unskilled person per day shall be levied on the contractor and recovery for the same shall be affected from contractor's dues not withstanding the fact if number of complaints of any nature is less or more. Attendance register shall be maintained by the JE for recording the absentee details and the same register will be signed by the contractor/ Supervisor daily, the AGE weekly and the GE on month end. A separate register based on atttendance register for recording recovery of contractor shall be maintained by the JE and the recovery if any will be forwarded to GE every month for necessary action at his end. Any descripancy or contest on the entries in the attendance register shall be written to GE within 48 hours of the entry in the attendance register, if not than the entries done will be binding and uncontested for. The department is not liable for the contractor signature in the register and it is the contractors prerogative to get it signed either himself or his supervisor.

(b) The complaints related to carpenter works, plumbing works, cement works and welding works against serial item Nos 137 (a) to 140 (c) shall be completed in 48 hours time after lodging/ receipt of complaints. Contractor shall ensure that all the complaints shall be attended and completed within above prescribed schedule/ time period, failing which, a penalty at the rate of double the quoted rate for that particular trade work/complaint per day till the satisfactorily completion of complaint shall be levied on the contractor and recovery for the same shall be affected from contractor's dues. A separate register shall be maintained for recording recovery for compliant not attend with in time period by the JE Remaining clauses pertaining to the register same as per para 155 (a) above

(c) For each complaint, a separate complaint slip shall be prepared by JE/ his representative and handed over to related tradesman, etc. for attending the complaint and after satisfactorily completion of complaint, compaint slip shall be submitted to concerned executive on the date as per Para 144 (b) above, which shall be got signed from the occupant and shall be produced at the time of payment to be made to the contractor. Complaints pertaining to same location and same nature consisting of replacement of maximum two fixtures in one quarter/ office/ building etc.involving movement of particular tradesman shall be measured and paid as one complaint. Replacement of more than two fixtures but multiple of three fixtures or part thereof in one quarter/ office/ building, etc. shall be measured as additional complaint.

(d) Ref Para 140(c) above any compliant of cement work below one Sqm will be given as single complaint, multiple of the same will be given as additional complaint.

(e) Complaint slip and complaint register etc. shall be provided by the contractor without any extra cost to the department and cost there of shall be deemed to be included in quoted rates by the contractor against respective items.

(f) Necessary transportations, tools, plants, ladders, including nails, screws, PVC washers, brass spindle, for bib taps/ stop cocks/ pillar cocks, cotton thread, Jumper valves, white lead, flush washers, internal fitting of low level flushing cistern, nipple, tee, elbow, plug, socket, reducer (GI/UPVC), M-seal, glass putty, hinges, handle, tower bolt, stopper, cement, white cement, sand other similar minor accessories required to complete the jobs/complaints shall be provided by the contractor without any extra cost to the department and cost there of shall deemed to be included in quoted rates by the contractor against respective item of schedule 'A'.

M/S MAHESHWARI ENTERPRISES (BID ID -3156576)

Priyadeep Construction (BID ID -3157060)

M/s AG PATHAN (BID ID -3156574)

M/S. M. F. Sharif & Co. (BID ID -3158116)

MATOSHREE CONSTRUCTION (BID ID -3157123)

Maruti Abhiyantriki (BID ID -3156871)

MS. G.A. CONSTRUCTION (BID ID -3157782)