Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹9.2 LAccepted-AOC | L1 | Accepted-AOC Being L1 bidder | |
| 2 | L2₹11.2 L+₹1.6 L (16.7%)Rejected-Finance | L2 | Rejected-Finance Other than L1 bidder |
Tender Value
₹15 L
EMD Value
₹30,000
Closing Date
16 Nov 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE AF Panagarh
GE AF PANAGARH MES AF STATION PANAGARH PO BIRUDIAH WEST BENGAL 713148
REPAIR/REPLACEMENT OF JOINERY IN MD ACCN IN DOMESTIC AREA AT AF STN ARJAN SINGH UNDER GE (AF) PANAGARH
2023_MES_621157_1
8742/E8
Open Tender
Civil Works
Item Rate
180 days
AF STATION PANAGARH
As per tender document
7 documents required · 7 mandatory
₹500
GE AF PANAGARH
₹30,000
1 Jan 2024
30 Sept 2023
18 Nov 2023
30 Sept 2023
16 Nov 2023
27 Oct 2023
Amount
Taking down chowkhats or frames (without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified and directed.
Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm and n.exc 4 Sqm each and removing to store complete all as specified and directed.
Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each complete all as specified and directed.
Taking down Shutters of any description area exc 1 sqm and n.exc 2.0 sqm for each leaf and refixing in same opening after cutting, adjusting and easing all as specified and directed
S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square complete all as specified and directed.
S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing mentioned in SSR Part-II 2010 complete all as specified and directed.
S&F for factory made 30 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (with sash bars, any numbers) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkhats complete all as specified and directed.
S&F for factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.
S&F for pressed steel door frame of size 165x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats, fixing holdfast, in bands etc. in PCC (1:3:6) type C-0, (using 12.5mm graded stone agregate) including necessary formwork complete all as specified and directed.
S&F for pressed steel door frame of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats, fixing holdfast, in bands etc. in PCC (1:3:6) type C-0, (using 12.5mm graded stone agregate) including necessary formwork complete all as specified and directed.
S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.4mm and fixed with tinned tacks, or stainless steel wire staples in steel windows/ wooden doors complete as in repair all as specified and directed.
S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.4mm and fixed with tinned tacks, or stainless steel wire staples in steel windows/ wooden doors complete all as specified and directed.
S&F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.
S&F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.
M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290, Gde E-165 complete all as specified and directed.
Hacking out broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old galzing pins/ spring clips complete all as specified and directed.
S&F for 3 mm thick sheet glass ordinary quality and glazing with oil putty/beads and pins/spring pins in squares n . exc 0.50 sqm in each pane to be fixed in any position at any hight upto to two story building complete all as specified and directed.
S&F for 3 mm thick figured glass pin headed type and glazing with oil putty/beads and pins/spring pins in squares n . exc 0.50 sqm in each pane to be fixed in any position at any hight upto to two story building complete all as specified and directed.
M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new or previously untreated wood and wood based surface over 10 cm width or girth not otherwise described including preparation complete all as specified and directed.
M&L for preparation of new or previously untreated steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
S &F for aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
S & F for 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.
S & F for 150 mm long aluminium alloy handles, cast type, anodized complete all as specified and directed.
S&F for 100 mm long Butt hinges (medium weight) stainless steel complete all as specified and directed.
S & F for 100 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.
S & F for 150 mm long aluminium anodised barrel tower bolts of extruded section complete as in repair all as specified and directed.
S & F for 150 mm long aluminium alloy handles, cast type, anodized complete as in repair all as specified and directed.
S &F for aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete as in repair all as specified and directed.
S &F for 3 ways sliding anodised aluminium (powder coated) glazed window shutter with frame with the following specification (a) Frame 50 mm x 65 mm x 1.5 mm Thick (b) 35 mm x 35 x 1.5 mm Z section in stiles, rails (c) 35 mm x 35 mm x 1.5 mm T section mullion (d) two shutter with PVC gasket with 4 mm thick tinted glass, including aluminium handles with necessary locking arrangement and one shutter with stainless steel wire cloth. 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc as directed by Engr-in-Charge.
S&F for Powder coated anodised aluminium ventilator shutters and frame (side hung type) without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing lips, rubber lips, rubber packing anodized aluminium snap beading, screws, grills anodized aluminium snap beading, screws, grills anodized aluminium fittings such as peg stays 150mm long (1 No), Hinges type B-21 100 mm long (3 Nos), suitable handle (1 No) etc. The vetilator system should be glazed with 4mm thick figured glass, pin head type of size as required in ventilator including taking out/ taking down old shutters complete all as specifed and directed.
S&F for 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete as in repair all as specified and directed.
Dismantling boarding of any description in any position with nails complete all as specified and directed.
S&F for kitchen cabinet (colour) of depth 300mm made with 18mm thick PVC celluca plywood board (pre-laminated with 5mm thick PVC sheet), one side decorative lamination and other side balancing lamination sheet (white) consisting of carcass 18mm thick PVC sheet and provision of shutter made out of 18mm thick one side decorative lamination PVC sheet all required brackets, stainless steel screw, knobs, kinges, favi quick, solvent cement etc. fixed to wall with stainless steel screw and 18mm thick PVC shelves of density not less than 600 kg/cum by drilling holes complete. The panel shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish as per make and specification all as directed by Enigneer-in-Charge. (Note: colour, quality and make approved by GE and cost of all materials and labours including in this item)
S&F for kitchen cabinet (colour) of depth 600mm made with 18mm thick PVC celluca plywood board (pre-laminated with 5mm thick PVC sheet), one side decorative lamination and other side balancing lamination sheet (white) consisting of carcass 18mm thick PVC sheet and provision of shutter made out of 18mm thick one side decorative lamination PVC sheet all required brackets, stainless steel screw, knobs, kinges, favi quick, solvent cement etc. fixed to wall with stainless steel screw and 18mm thick PVC shelves of density not less than 600 kg/cum by drilling holes complete. The panel shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish as per make and specification all as directed by Enigneer-in-Charge. (Note: colour, quality and make approved by GE and cost of all materials and labours including in this item)
M&L for 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work with external 6mm thick teak wood lipping complete all as specified and directed.
M&L for plain fillets, square rectangular or triangular in section clean sawn secured with nails or brads second class hard wood wrought exc 6 n exc 13 sq cm complete all as specified and directed.
S&F for cutain rails, mild steel, chromium plated with fixing brackets, stops, tollers etc. including side caps and brackets complete as in repair all as specified and directed.
M&L for rendering 20 mm thick in cement mortar (1:4) in two layers (12mm +8mm) on external faces of brick wall or concrete surfaces, finished even and smooth without using extra cement with using approved LWPC on second layer (8mm) as per manufacturer instruction after taking down old cement plaster complete all as specified and directed by Engineer-in-Charge. (Note:- WPC will be measured and paid separately as supply only)
Supply only liquid water proofing compound
M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work, finished even and smooth without using extra cement after taking down old cement plaster complete all as specified and directed by Engineer-in-Charge.
M&L for rendering 5 mm thick in cement mortar (1:3) on fair faces of concrete surface, as in ceiling and finished even and smooth without using extra cement after taking down old cement plaster complete all as specified and directed.
M&L for applying two coats of weather proof exterior emulsion (Anti fungal paint) over a coat of primer including preparartion of new plastered surfaces of walls complete all as specified and directed.
M&L for applying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint over a layer of smooth wall putty finish punning 2 mm thick strictly as per manufacturer instruction with smooth roller finish after preparation of new plaster surfaces of wall complete all as specified and directed by GE. (Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement)
M&L for applying three coats of white wash including preparation of newly plastered/unplastered surfaces of ceiling complete all as specified and directed.
M&L for complete removal of existing treatment of walls by washing down and smoothing old surface and applying two coats of oil bound distemper (premium quality) over one coat of alkali resistant primer paint over a layer of smooth wall putty finish punning 2 mm thick strictly as per manufacturer instruction with smooth roller finish complete all as specified and directed by GE. (Note:- After painting works, cleaning of all floors, glass and furniture by own arrangement)
M & L for PCC (1:2:4) type B0 (using 12.50 mm crushed stone aggregates) as in levelling course, roof kerbs or mud stops, rounded or chamfered on edges etc. after demolition of cement concrete of any description in any position complete all as specified and directed.
M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premisescomplete all as specified and as directed.
M&L for glazed ceramic coloured tiles of size 450x350x7mm/ 600 x 300 x 7mm (premium quality) on vertical surface such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick screed bed in cement mortar (1:4) after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and as directed.
M&L for 20mm thick granite stone slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in, laid over 15mm thick bedding in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab including rounding edges of granite slab as directed by Engineer-in-Charge as required at site complete all as specified and directed.
Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings complete all as specified and directed.
S&F for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.
S&F for pre-painted galvalume aluminium zinc coated GI based plain steel 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters, fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.
Dismantling of wrought iron or mild steel work of any type and size not otherwise provided complete all as specified and directed
S &F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 after dismantling of old mild steel work of any description not otherwise provided for complete all as specified and directed.
S&F for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle conforming to Fe-410W (Gde-E-250) quality-A after dismantling of old mild steel work of any description not otherwise provided for complete all as specified and directed.
S&F for stainless steel plate rack of size 1200mmx 900mmx1mm thick as in repair complete all as specified and directed.
ANSH CONSTRUCTION
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.PDF
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .