AR AND SR TO RB HOUSE NO. 3436 AND OTHER HOUSES TYPE V SECTOR 24 CHANDIGARH.

Providing and fixing 60 mm thick high density rubber moulded precast cement concrete paver block grey/ colored/ polished/ designer (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M35 ISI marked including the cost of good quality color and hardening agents. The paver should be compiled with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to bear as per IS 1237-1980 (specification for cement concrete floor tiles). The paver should be laid over layer of 25 mm average thick screened coarse sand to the required slope and filling the joints with fine sand complete in all respects and to the entire satisfaction of Engineer in charge.

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Providing and fixing IRC welded mesh 30mm x 30mm in M.S. angle frame of 30x30x3mm and M.S. flat 20x5mm on the inner side including cost of cutting welding, fixing the complete frame in the exisitng brick / RCC structure with 3" long 8 nos. fasteneres including painting two coats of synthetic enamel paint over one coat of metal primer complete in all respects and to the entire satisfaction of the Engineer in charge.

Providing and laying antiskid vitrified floor tiles of size 600 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade. The tiles are to be laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand). The tiles are to be fixed with 2 mm grove using spacers. The grove are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to entire statisfaction of Engineer in Charge.

Providing and laying vitrified floor tiles of size 600 x 600 mm single charge (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade. The tiles are to be fixed with 3mm grove using spacers. The tiles are to be laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm The grove are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material. Single charge vitrified tile of size 600x600 mm

Providing and laying 1st quality ceramic glazed wall tiles of size 300x450 mm conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make, in all colours, shades as approved by Engineer-in-Charge,in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand). The tiles are to be fixed by provding 2 mm thick spacer. The area of spacer is to be filled by using cement based grout of approved shade. The grooves are to be filled with cemenitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to entire statisfaction of Engineer-in-Charge.

Dismantling of ceramic tiles or vitrified and plaster to making the surface clean for refixing the glazed tiles including removing of malba complete in all respect and to the entire satisfaction of the Engineer in charge.

Providing and fixing 1.5mm thick polycarbonate sheet to be fixed on the existing MS frame with self drilling machine screws complete in all respect to the entire satisfaction of Engineer-in-charge.

Steel work in built up frame made of / M.S. flat / M.S. pipe / M.S. angles of various sections including cutting, hoisting fixing in position and applying a priming coat of approved steel primer and two coats of snthetic enmael paint, welded and bolted including special shaped washers etc.. The work is required for making security wall jaffery/ ladder/grills/ frame work for shed or sunshade / other mis work.The steel work is to be provided at the site of the building complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing 3.0 mm thick clear polycarbonate sheet to be fixed on the existing MS / wooden frame with self drilling machine screws including remove the old polycarbonate sheet complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 35mm thick phenol bounded factory manufactured solid flush door shutter ISI marked with both side commercial face in the existing chowkhat. The rate includes the cost of iron hinges, all necessary Aluminium fittings and painting two coats over one coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing golden champ wood chowkhat (kiln seasoned) 4 1/2" x 2 1/4"including cost of corner straps, iron hold fasts, hinges, screws,nails, fevicol etc. and painting two coats of wood preserver to sides of chowkhats. Rate includes the cost of dismantling of all damaged chowkhats and making good the damage to walls plaster and floors as required including, disposal of rubbish to the dumping ground the rate further includes the cost of painting two coats synthetic enamel paint over one coat of wood primer complete in all respect and to the entire satisfaction of Engineer-in-Charge.

Providing and Fixing 35mm thick golden champ wood (kiln seasoned) wire guage door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” golden champ wood (kiln seasoned) beading, with two vertical members in each panel to hold wire mesh, with necessary 4 Nos. of hinges 4", 2 Aluminium Tower bolts 6", 2 Aluminium Handles 5” and Aluminium door stopper and single acting door spring and complete fixed in position including two coats of paint and one coat of primer after preparation of surface (special quality) Complete in all respect to the entire satisfaction of Engineer-in-Charge.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (One or more coat applied @0.90 Itr/10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing stainless steel finish tower bolts (barrel type) of size 250x 10mm with necessary s.s. screws etc. complete in all respect and to the entire satisfaction of the Engineer in charge

Providing and fixing stainless steel finish handles of size 125mm with necessary s.s. screws etc. complete in all respect and to the entire satisfaction of the Engineer in charge

Providing and fixing 150 mm stainless steel finish floor door stopper with rubber cushion, necessary s.s. screws etc. to suit shutter thickness complete in all respect and to the entire satisfaction of the Engineer in charge

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing 28mm thick wooden or stainless steel finish metallic drapery pipe including wooden brackets etc. complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 4mm thick plain glass panes with beading when required over exixting chowkhat or fixed shutter or fixed portion or glazed shutter including the cost of nails, putty etc. complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing of cupboard shutter consisting of 19mm thick commercial board with lipping all around and fixed with chowkhat frame with piano hinges and screws etc. and provide with Alum. handle (with base plate) and magnetic catcher. The board surface is to be painted with two coats of special quality synthetic enamel paint after primer coat and preparation of surface, complete frame is to be fixed with iron nails etc. complete in all respects and to the entire satisfaction ofthe Engineer in charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Please Enable Macros to View BoQ information