CERTAIN REPAIR TO ROOF, CEILING, FLOORING,JOINERY, SANITARY FITTINGS, PLUMBING AND LAGGING IN ZONE A UNDER AGE B/R-I AT BB CANTT SRINAGAR

Amount

Dismantling plain or corrugated steel sheeting, any gauge thickness including nainital or similar pattern roof coverings complete all as specified and directed.

S&F Galvanised, corrugated mild steel sheeting with two corrugation side lap fixed with coatch screws and washers in roofs, 0.63 mm thick m Gde-o quality, with 120 grms/sqm zinc coating and Gde 'B' (i.e 12.5 mm ) corrugation complete all as specified and directed.

S&F 0.80 mm thick plain, galvanised, mild steel sheeting (ISI Marked) grade 'O' with minimum 120 grms/sqm for zinc coating in ridges, hips, valley gutters, drip and straight flashings, fixed with coatch screws and washers complete all as specified and directed.

S&F pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 2 mm thcik fibre glass reinforced translucent sheeting fixed with adequate size of nut & bolt in roof/wall or in similar works complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Dismantling timber scantling 40 sqm and over in section in any position as in unframed/framed work complete all as specified and directed.

M&L 2nd class soft wood (kail) as in scantling clean sawn complete all as specified and as directed.

Dismantling of wall and ceiling boards (fiber pulp, insulation, etc..) or unsulation boards/slabs, any thickness, including cover fillets complete, all as specified and directed.

M&L for 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work, fixed in ceiling complete all as specified and directed.

M&L Khatamband pattern false ceiling, design as approved by GE with ornamental wood work made out of stainless including 12mm thick BWR plywood and necessary frame work and finally finishing with french polish (two or more coats) fixed complete all as specified and directed.

S&F Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including GI frame work for gypsum board made out of GI sheet not less than 20 gauge thickness in ceiling fixed with screws frame suspended with 4mm dia GI wire as per manufacturers instructions complete all as specified and directed.

M&L 12mm thick perforated particle board/ tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples on snap grid Anodised aluminium frame work for false ceiling all as specified Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

M&L Australian wood panelling 10mm thick including 9mm thick BWR plywood on the wall and finally finishing with french polish (two or more coats) fixed complete in repairs complete, all as specified and directed.

S&F 2nd class hard wood plain clean sawn fillets square, rectangular or triangular in section exc 6 & n.exc 13 sqm secured with nails or brads complete all as specified and directed.

S&F in repairs 20mm thick boarding clean sawn as in eaves board fixed with nails complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floor and paving n.exe 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 25 mm thick plain cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in sub base of floors finished even and fair complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sq.m but not exceeding 0.11 Sq.m, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for Non skid ceramic coloured tiles area of each tiles (Square / rectangular) exc 0.11 sqm but n. exc 0.18 sqm 7 to 8 mm thick in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Vitrified coloured ceramic tiles 10 mm thick (square/rectangular) polished area of each tile not exc 0.36 sqm in floors set and jointed in neat cement slury and pointed in white or coloured to match the tiles over 15 mm thick screed bed or bedding layer of mortar 1:6 for layig floor finish complete all as specified and directed.

M&L 40 mm thick cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in flooring finished even and smooth without using extra cement complete all as specified and directed.

Supply of 3 mm thick glass dividing strips, width 38 mm and inserted in position conforming to design complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed.

M&L for Glazed ceramic coloured/printed tiles 450X 350X 7mm thick as in vertical surfaces such as dado, skirting set jointed in neat cement slurry including pointed in white or coloured cement to match over and including 10 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors/wall etc laid bedded and pointed in any mortar complete, all as specified and directed.

M&L for Granite (of any type) work ,20 mm thick, (table rubbed and polished) in steps jambs , pillars ,window cills ,cooking platforms ,and the like in cement mortar (1:4) including pointing in white cement (1;2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thcik screed bed or bedding layer in CM 1:3 complete all as specified and directed.

M&L for 20-25mm thick machine cut Kota stone slab in flooring laid over 20mm thick cement screed bed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking out UNSV storage water tank of capacity 1000 Ltrs complete, all as specified and directed.

Taking out UNSV storage water tank of capacity 500 Ltrs complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) hoisted and fixed in position incl all accessories of capacity 1000 ltrs Make : Sintex/Star/Polycon, Fusion or equvalent

S&F rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) hoisted and fixed in position incl all accessories of capacity 500 ltrs, Make : Sintex/Star/Polycon, Fusion or equvalent

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 25 mm dia complete all as specified and directed.

M&L for removing old spun yarn lagging material from GI tubing any size including plaster of paris and removing away to a distance of 50m away from the bldgs complete all as specified and directed.

M&L for lagging to pipes of internal dia 15 mm used in internal water supply or plumbing all round with, 25 mm thick bonded mineral wool preformed 'SNAPON' pipe sections of density 144 Kg/cum conforming to IS-9842 with 0.01 mm aluminium foil complete all as specified and directed.

M&L for lagging to pipes of internal dia 20 mm used in internal water supply or plumbing all round with, 25 mm thick bonded mineral wool preformed 'SNAPON' pipe sections of density 144 Kg/cum conforming to IS-9842 with 0.01 mm aluminium foil complete all as specified and directed.

S&F in repair 15 mm dia bib taps, cast copper alloy wth crutch or butterfly handle, screwed down, screwed for iron pipe of size 15 mm dia and confirming to IS-781-1977 complete all as specified and directed.

S&F in repair CP centre hole single lever basin mixer fancy type for WHB with double action for hot/Cold water complete all as specified and as directed. Make :- Jaquar (Aria collection) Cat Part No ARIA-39051B or equivalent as approved by GE

S&F in repairs fancy type curtain rods metal polished 20/25 mm dia with end fittings and fixing brackets of required size ( two nos end brackets and two Nos wall brackets fixed with wooden gutties and screws) complete all as specified and directed.

M&L PBS roll 20 mtr long and 100 cm wide type-III weight 40 Kg per roll (As per sample) complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frames) not exc 1.5 sqm each including cutting holes for taking out hold fasts or dismantling brick work/stone work (holes cut and any other damage to jambs walls for taking out hold fast shall be finished identical to existing finish without any extra cost to the govt) complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4 sqm each including cutting holes for taking out hold fasts or dismantling brick work/stone work (holes cut and any other damage to jambs walls for taking out hold fast shall be finished identical to existing finish without any extra cost to the govt) complete all as specified and directed.

Taking down shutters of any description n.exc 1 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each complete all as specified and directed.

S&F 2nd class soft wood plain, solid chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints complete all as specified and directed.

S&F 35 mm thick 2nd class soft wood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers complete all as specified and directed.

S&F 35 mm thick 2nd class soft wood (kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze et (without sash bars), edges of framing plain,, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section -8 clause 8.24 (a) complete all as specified and directed .

S&F 30 mm thick 2nd class soft wood (kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze et (without sash bars), edges of framing plain,, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section -8 clause 8.24 (b) complete all as specified and directed .

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications and drawings complete all as specfied and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered, with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F butt hinges, medium weight cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F butt hinges, medium weight cold rolled, mild steel of size 75 mm complete, all as specified and directed.

S&F 150 mm long aluminium barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100 mm long aluminium barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100 mm aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc 0.50 sqm in each pane complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F 5 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F in repair Door closer (Aluminium extruded section body) hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed.

M&L for preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F aluminium door air tight anodized frame made of size 100 x 45 x 1.5 mm with one or more rebate jointing cleats, hinges etc for fixing anodized aluminium door shutter fully paneled,( two Nos of panel on each shutter) with 5.5mm thick tinted plain glass shutter rail made of size 80mmx45mm1.5mm (top, bottom, middle and side rail). Single/double leaf side hung type including necessary joint cleats, anodized aluminium fittings such as aluminium butt hinges 100mm long 4 Nos on each shutter, aluminium anodized tower bolt 200mm long 3 Nos for each door, aluminium anodized handle 150mm 2Nos 'D' type for each shutter, locking 6 lever of Make:-Harrison one on each shutter including hydraulic door closer. All door fittings except cleat shall be ISI marked (Size of each door shall be as per site requirement) complete all as specified and directed.

M/S Paradise Constructions

M/S MOHAMAD YOUSUF AKHOON AND SONS

MOHAMMAD YOUSUF MIR