Renovation of Estate Water Supply Sewerage System Sanitary Fixtures Wall Tiles Floor Tiles Doors Distempering Painting and other works contingent at Trauma Centre Ground and first Floor at Guru Nanak Dev Hospital Amritsar Deposit Work

Amount

Dismantling cement conglomerate floors (25mm to 50mm) thick including concrete base.

Dismantling glazed tiles (to be carefully removed).

Scraping Cement Plaster.

Disposal of Malwa from dismantling etc.

Supplying and filling cinder on roof (1st Storey)including light ramming.

Screed of 50mm thick cement concrete 1:8:16 to be laid below the topping, using mechanical mixer for mixing of material including carriage.

Providing and fixing in position H.C.I. soil waste vent or antisyphonage pipes to I.S.I. specification (IS:1729) of approved make (to the approval of Engineer-in-charge ) including cutting, jointing, wastage, but excluding cost of lead jointing.

100mm i/d H.C.I. pipe line laid complete

75mm i/d H.C.I. pipe line laid complete

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B-Class Premium make such as (Jindal Hisar) including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.

Providing, fixing and jointing ISI Marked Gun-Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete.

50mm i/d Gun Metal peet valve heavy pattern.

Providing, fixing and jointing G.I Union Couplings(of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.

50mm i/d G.I. Union

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required.

Through wall 11.43 cm thick

Through wall 22.86 cm thick

Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling, using mechanical mixer for mixing of material including carriage.

Providing & fixing factory made Solid PVC Chowkhat Door frame of the size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5mm PVC foam sheet, mitre cut at 2corners & joined with 2Nos of 150mm long brackets of 15 x 15mm M.S square tube. The two vertical doors profiles are to be rainforced with 19x19 mm MS square tube of 19 guage, the door framed shall be fixed to the wall using 65/100 mm long MS screws throguh the frame by using fasteners, the minimum of 4 Nos. of screws to be provided for each vertical member and minimum 2 Nos of Horizontal member etc. as per manufacturer's specification, confirming to test cretieria by specified in IS:4020-1998, drawing and to be entires satification of Engineer-in-charge.

Providing & fixing 30mm thick Factory Madesolid Panel PVC Door shutter (Pannel thickness 5mm) Consisting of frame made out of M.S tubes of 19 guage thickness and size of 19mm x 19mm for styles & 15mm x 15mm for top & bottom rails. M.S frame shall have a coat of steel primers of approved make & manufacture. M.S frame shall be covered with 5mm thick heat moulded PVC 'C'Channel of size 30 x 50mm forming styles, and 5mm thick, 75mm wide PVC sheets for top rail, lock rail and bottom rail on either side, and 10 mm (65mm x2mm) thick, 20 mm wide cross PVC sheet as gap insert for top rail and bottom rail panneling of 5 mm thick PVC sheet to fitted in the MS frame welded/sealed to be styles and rails with 30 mm wide into 5 mm thick PVC sheet bedding on either side and joined together with solvent cement adhesive and adittional 5 mm thick PVC stripes of 20 mm width is to be stuck on the interor side of the 'C' channel using PVC solvent cement adhesive etc. complete as per manufacturer's specification, confirming to test cretieria by specified in IS:4020-1998, drawing and to be entires satification of Engineer-in-charge.

Anti-skid floor tiles 10mm thick in flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with white cement slurry in joints including corners angles and beading including carriage.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 300 x 600 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete including carriage.

12.5 mm thick cement plaster 1:4 including carriage.

Preparation of plastered surfaces for distempering including surface, applying filling with approved quality filler consisting of plaster of Paris and chalk mitti including finishing the surface to the required finish complete.

Distempering with dry distemper of approved manufacture two coats over one priming coat to give an even shade.

Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification (IS:1729) of approved make (to the approval of Engineer-in-charge) of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc. minimum depth of water should be 150mm with a minimum seal 50mm.

With 75mm i/d outlet deep seal

With 75mm i/d outlet shallow seal

Providing lead caulked joints to H.C.I. pipes and specials conforming to I.S.I. Specification (IS:1729) of approved make (to the approval of Engineer-in-charge ) including cost of lead yarn, fuel and tools etc.

75mm i/d (1.13 kg.)

100mm i/d (1.36 kg.)

Providing & Fixing in position M.S or heavy flat iron clamps made out of M.S flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyhonage pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting.

M.S. Holder bats clamps for 100mm i/d H.C.I. pipes

Providing and fixing in position H.C.I specials for soil waste vent or anti syphonage pipes to I.S.I specifications (IS:1729) of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.

For 100mm i/d pipe

Heal Rest Bend

Bend plain

Collars

For 75mm i/d pipe

Heal Rest Bend

Bend plain

Collars

Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.

160 mm o/d pipes

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm.

100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm

Providing and fixing in position Chinaware Indian Orisa water closet size 580mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap complete in all respect.

Size 550 mm x 400 mm

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect.

C.P. brass towel Rails size 15mm dia 600mm long

C.P brass towel ring

Providing and fixing in position vitreous Chinaware white large flat back or angular lipped front urinal 610 mm high of approved make (to the approval of the Engineer-in-charge) (610 mm x 410 mm x 380mm) consisting of C.P. waste 32 mm dia and C.P. brass spreader, complete.

Providing and fixing in position vitreous Chinaware white channel of approved make (to the approval of Engineer-in-charge) of size 600 mmx100mm including laying and fixing in cement concrete 1:2:4 complete in all respect.

Providing and fixing jet spray with 2'-6" long PVC pipe.

With PTMT nut

Providing and fixing PVC waste pipe 32mm complete in all respect.

Vitreous white Chinaware Partition

Large partitions size 835mm x 355mm

Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect.

C.P.brass 15mm Concealed stop cock with flange.

C.P.brass 15mm Angle valve without flange

Providing and fixing in position C.P. brass overhead shower 1 flow without shower arm with 15mm i/d inlet of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect.

C.P. Brass khunti with 3 pegs

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers complete in all respect (as required by the Engineer-in- Charge)

Size 550mmx400mm

Providing & Fixing in position C.P. Brass flange of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25mm long to 50mm long of approved make (to the approval of Engineer-in-charge )with various fixtures complete in all respect.

Providing & Fixing in position 15mm i/d bib cock of approved make (to the approval of Engineer-in-charge) complete in all respect.

Brass Bib cock/Stop cock 15mm x 400gm

C.P. brass Bib cock long nose/ long body without flange

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect.

PVC tube connection of size 15 mm x 450 mm with C.P. Brass nut

Cost of Aluminium fittings complete for doors,windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt)

For shutter area above 0.50 sqm

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, lime concrete with 40 per cent lime mortar 2:3 in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside light duty C.I. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.

Providing and fixing in position H.C.I. soil waste vent or antisyphonage pipes to I.S.I. specification (IS:1729) of approved make (to the approval of Engineer-in-charge ) including cutting, jointing, wastage, but excluding cost of lead jointing.

Cement concrete 1:2:4 with stone ballast shingle

First Class brick work in cement sand mortar 1:5 In foundation and plinth

Cement concrete for 1:2:4 for benching excluding stone ballast or shingle

Reinforced cement concrete M-20 mechanical batch mixer, mixing batch type concrete mixer as per ISI 1791 and vibrated by needle vibrator but excluding steel reainforcement centring and shuttering in foundation and plinth

Cold twisted deformed (Ribbed/Tor steel Bar) Bars Fe 500 grade as per IS 1786-1985 for RCC works, where not including in the complete rate of RCC including bending and placing in position complete.

12.50 Thick cement plaster 1:2 and cement rendering on plaster 1 mm thick.

Providing & fixing 560 mm, 500 mm and 450 mm internal diameter circular or 450 mm x 600 mm clear inside opening rectangular RCC manhole cover and frame ISI marked as per IS: 12592-2002 including carriage from the stores of the Engineer-in-charge to site of work, loading unloading including staking and setting the same to correct lines over manholes including cement concrete topping (M-20) around the frame etc. dia of steel for lifting hook is 16mm (for EHD and HD) RCCcover including 450 mm frame midium duty.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.