SPL REPAIR OF OTM ACCN BLDG NO ASC 31 AND 32, PROVN OF FOOTHPATH AND RAIN SHED AT UMROI MIL STN UNDER GE UMROI

Amount

Taking down cement plaster, of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.00 kg of cement per sqm complete all as specified and directed.

Material and labour for coloured non skid ceramics tiles 7 to 8mm thick (square/ rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors over and including 15mm thick screed bed/bedding layer in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor make as a specified.

Material and labour for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00 sqm with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frame), complete all as specified and directed.

Taking down shutter of any description exc 1.00 sqm but not exc 2.00 sqm each, complete all as specified and directed.

Refixing shutter in same opening after repairing complete area exc 1.00 Sqm but not exc 2.00 Sqm, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube fixed as per manufacturer instructions complete all as specified and directed.

Supply and fixing 35 mm thick Flush door shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F Factory made solid PVC moulded door shutter 28 to 30mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm PVC sheet on back face, fixing in frame at site as per specification & drawing, complete all as specified and directed.

M & L 35mm thick glazed and skelton shutters, open rebated and prepared to receive glass , gauge, etc (without sash bars) , edges of framing plain, chamfered of rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as spd in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkhats, complete all as specified and directed.

S&F stainless steel wire cloth , 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

M & L for Anodised powder coated (minium thickness 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

M & L for Anodised aluminium sliding window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.), complete all as specified and directed.

M & L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and peration of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed.

Supply & Fixing 4mm thick sheet glass ordinary quality, glazing in square/ rectangle n,exc 0.50 sqm each pan with oil putty or aluminium beads fixed to steel etc complete complete all as specified and as directed.

Material & Labour 4mm thick figured glass, n.exc 0.50 sqm each pan, pin headed type and glazing with oil putty or aluminium beads fixed to steel etc complete all as specified and as directed

Material & labour preparation of new wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

S & F aluminium alloy handles size 150mm fabricated type anodised complete all as specified and as directed

S & F aluminium anodised barrel tower bolt 200mm size of extruded section and fixed complete all as specified and as directed

S & F 300 mm long aliminium alloy ,anodised sliding door bolt with hasp and staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast alunimium alloy and fixed, complete all as specified and as directed

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed, complete all as specified and as directed

Material & labour flat iron mild steel for hold fast size conforming to Fe-410-0 or Fe-310-0, complete all as specified and as directed

M&L for cement concrete (1:2:4) type B0 (using 12.50mm graded stone aggregate) as in cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, Copings, etc, complete all as specified and as directed

S&F helical door spring 300mm long including roller and roller plate, complete all as specified and as directed

S&F Stainless Steel tubular 20mm dia decorative curtain rod, complete all as specified and as directed

S&F Stainless Steel decorative brackets for curtain rod in any size, complete all as specified and as directed

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removal to store, complete all as specified and as directed

S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 and fittings as in walls, ceiling, floor, etc, complete all as specified and as directed (upto 04 storey High of building)

S&F 1000 ltrs capacity rotational moulded polyethylene water storage tanks (Cylindrical verticle with closed top) noisfed and fixed in position including taking down old one, complete all as specified and as directed

S&F in repair PVC valve less syphonic action flushing cistern type 9 to 10 ltrs capacity with inlet, ball valve, float and handle including bracket, white colour of approved make, complete all as specified and as directed

Supply and fix in repairs of vitreous china squatting pan of Orissa pattern size 580 mmx440mm white with P or S tap front or back inlet and integral foot rest ( Excluding flushing cistern and flush pipe), complete all as specified and as directed

S&F in repair vitreous china wash down water closet (pedestal pattern) white with 'P' or 'S' trap front or back inlet, complete all as specified and as directed

S&F in repair wash hand basin, white flat back of size 550 x 400mm excluding piller taps but including waste cupling, waste pipe and bracket etc, complete all as specified and as directed

M&L for Green Marble 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble over and including 15mm thick screed bed/bedding layer in CM 1:4 complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick surfaces finished even and smooth without using extra cement, complete all as specified and as directed

Material and labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, chajja, fins, facia etc upto 3 storey height mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and as directed Note :- (a) Supply only water proofing compound shall be measured and paid separately under relevant items. (b) Cost of scafolding upto 3 storied height of building for rendering is included in this item. (c) Rendering will be done in two layers. 1st layer will be 10 mm thick and 2nd layer will be 5 mm thick. water proofing shall be use in top layer only (5mm thick) .

Supply only Liquid water proofing compound.

Material and labour for 5 mm thick rendering in cement mortar (1:3) on concrete surface as in ceiling/chajja finished even and smooth without using extra cement, complete all as specified and as directed

Material and labour for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and as directed

S&F in repair PVC ball valve 20mm high pressure of PTM with epoxy coated aluminium rod and high density plastic ball serewed for iron pipe, complete all as specified and as directed

Taking down soil pipe/ rainwater pipes (any size or pattern ) including all fitings heads shoes bends swan -necks etc including cleaning or refixing or removal to store (measured over all fixed along the centre line over fitting and ( accessories), complete all as specified and as directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including scafolding upto 03 story building etc, complete all as specified and as directed

S&F for 110mm dia pvc bend etc with access door fixed with rubbr ring fixed to wall including scafolding upto 03 story building etc, complete all as specified and as directed

S&F for 110mm dia PVC (SWR) branch piece,single (single Y) equal or unequal with access door including scafolding upto 03 story building etc, complete all as specified and as directed

S&F for 110mm dia PVC (SWR) junction single, (Single T) equal or unequal with access door including scafolding upto 03 story building etc, complete all as specified and as directed

M&L for 75MM PVC (SWR) floor trap, plain with grating including jointing with solvent cement, including making good distrubd area/surfaces with cement concrete/cement mortar 1:2:4 etc including taking down old unserviceable Nahani/Floor trap, complete all as specified and as directed

S&F in repairs 15 dia fancy type chromium plated Bib tap cast copper alloy etc complete all as specified and as directed.

S&F in repairs of stop valve 15 mm dia CP fancy type, with long shank and cup (concealed type) cast copper alloy, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of stop valve 15 mm dia CP fancy type, with long shank and cup cast copper alloy, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in repairs 15 mm dia fancy type pillar tap cast copper alloy, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe & fixed, complete all as specified and directed.

S&F in repairs Shower Rose 125mm size Chromium plated with swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.

S & F in repairs Brass chromium plated tubelar towel rail, 20mm dia, D type, 60,cm long between flanges, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth in brick walls etc, complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1.5mm thick internal wall care putty and primer using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

Material and labour for Scrapping and preparation of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 1.5mm thick internal wall care putty and primer using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.

M&L for prepration of new plastered surfaces and applying two coats of weather proof exterior emulsion paint (Apex Ultima or equivalent) (any colour/tint) with approved colour and pattern over a coat of 1 mm thick external wall care putty and a coat of approved alkali primer as on walls of bldgs of any height including necessary scaffolding and safety measures and procedure complete all as specified and directed.

M&L for scrapping and prepration of old plastered surfaces and applying two coats of weather proof exterior emulsion paint (Apex Ultima or equivalent) (any colour/tint) with approved colour and pattern over a coat of 1 mm thick external wall care putty and a coat of approved alkali primer as on walls of bldgs of any height including necessary scaffolding and safety measures and procedure complete all as specified and directed.

M&L for preparation of old plastered ceiling surfaces and applying two coat of white wash (any colour/tint) on ceiling surfaces, complete all as specified and directed.

Material and labour for preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Material & labour 2nd class hard wood, plain, solid straight chowkats and frames worught, framed, rebated on the solid rounded of chamferred, put together with glue, pinned at joints supplied and fitted, complete all as specified and directed.

Demolition of brick work built in CM including all quoins,arches,pillars etc, complete all as specified and directed.

Material and labour for Pre-cast cement concrete block masonry, type C1 (1:3:6), (using 20mm graded stone aggregate), in cement mortar 1:6 with solid blocks, exc. 10 cm in width and setting in mortar, complete, complete all as specified and directed.

Demolition of cement concrete of any dsecription and in any position not otherwise specifically provided for etc, complete all as specified and directed.

M&L for PCC 1:5:10 Type E2 (using 40mm graded crushed stone aggregate) as in filling sunken floor complete all as specified and as directed by Engineer-in-charge., complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 Type B-0 ( using 12.5mm graded crushed stone aggregate) as in sub base of floor, complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C1 using 20 mm graded aggregate as in plinth protection finished fair and even with using extra cement, complete all as specified and as directed

Taking down of existing roof treatment from roof and terrance, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specification :- (a) Apply cement slurry over concrete surface @ 3Kg/Sqm. (b) Rendering 15mm thick in cement mortar (1:4) mixed with water proffing compound as per manufactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). (c) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25 litres per Sqm conforming to IS: 3384-1986. (d) Applying evenly one coat of blown hot bitument of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (e) A layer of APP based polymeric membrane, 3mm thick (minimum), weighing 3.5 kg/m2 reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (f) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane

Dismantling AC/CGI/PPGI corrugated or semi corrugated sheets in wall cladding or roof coverings and hanger doors including ridges and make good for aluminium earthing strips after fixing of sheets, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating PPGL based corrugated/Trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating PPGL based plain steel sheet 0.60mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, eave board, fixed with self tapping screws, complete all as specified and directed.

Material and labour for complete/Partial removal of loose/ cracked concrete including cutting of reinforcement at Single/Double/Tripal storey if required from RCC roof projection, chajja, fins, facia etc and applying bonding agent as per manufacture instruction as per and making good with RCC (1:1.5:3) type A0 using 12.5 mm graded aggregate) in any slab and in any position finsihed the surface even and smooth with out using extra cement including necesary formwork and welding/binding of reinforcement if required, complete as directed by Engineer in charge. Note:- (1) reinforcement will be measured and paid seperately under respective items, (2) Rate shall be inclusive of bondig agent fosroc nitobond EP ,Sika hibond, Pidilite 301 pidicrete URP. 2) The rate shall be inclusive of Scaffolding if required.

M&L for Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) etc complete all as specified and as directed.

S&F in repairs PVC connection pipe 15mm size with PTMT nuts of length 450mm long, complete all as specified and as directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed

M&L for Providing and fixing false ceiling of designer tile ivory painted (high pressure steam cured ) of 4mm thick (as per IS: 14862) of size 595x595mm and any one of the design (cascade or electra) in true horizontal level. Suspended on inter locking metal grid of hot dipped galvanized steel section (galvanized @120gms both side inclusive and black painted groove on all T webs)consisting of main T runner with suitably spaced joints to get required length and 15x32mm made of 0.3mm thick sheet spaced at 1200mm c/c and cross T of size 15x32mm made of 0.3mm sheet 1200mm long spaecd between main T at 600mm c/c to form a grid of 1200x600mm and secondary cross T of length 600mm and size 15x32mm made of 0.3mm thick sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including required cutting/making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.Main T runners to be suspended from trusses/ceilings using suitable suspension arrangement as per manufacturers instructions/literature. GI adjustable wire of 4mm dia with galvanized butterfly level clips spaced at 1200mm c/c along main T bottom exposed width of 15mm of all T section of 4mm dia GI wire shall be pre-painted with with polyster paint and black painted groove at centre of size 4mm depth and 4.5mm width, complete at all heights as per direction.

Surface dressing not exceeding 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil, complete all as specified and directed.

Material and labour for plain Cement Concrete (1:4:8) type D2 using 40 mm graded aggregate as in foundation, filling and mass concrete all as specified and directed.

Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm, complete all as specified and as directed

Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point, complete all as specified and as directed

Material and labour for hardcore of broken stone of gauge not exc. 63 mm deposited, spread and leveled in layers not exc. 15cm thick, watered and rammed to a true surface, complete all as specified and as directed

M&L for 75mm thick PCC(1:4:8) type 'D-2' (using 40mm graded crushed stone aggregate) as in path/Hardstanding, complete all as specified and as directed

Material and labour for 15 mm thick rendering in cement mortar (1:4) on fair face of brick or concrete surface finished even and fair, complete all as specified and as directed

Material and labour for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick surfaces finished even and smooth without using extra cement, complete all as specified and as directed

Material and labour for applying two coats of cement base paint over one coat of alkali resistant primer on plastered surfaces of walls including preparation of new or previously untreated surfaces, complete all as specified and as directed

M& L Sand Spreading and levelling under inter locking paver block complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking rubber moulded paver block with grey cement and colour pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and as directed.

Excavation in post holes (or similar holes) each not exceeding 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surfaces in soft/loose soil, complete all as specified and as directed

M&L for 100mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in path/Hardstanding, complete all as specified and as directed

M&L for Virified Ceramic tiles Light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. over and including 15mm thick screed bed/bedding layer in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and as directed.

Material and labour for Cement Concrete (1:3:6) type C2 using 40mm graded aggregate as in Pillars, boundary pillars, posts etc. filling and mass concrete all as specified and directed.

Supply and fix steel work in tubular trusses,vertical post and purlin including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161 – 1979 grade St – 240 etc, complete all as specified and directed.

M&L rolled mild steel plate Fe-290(Gde E-165) (plain or chequred) with reveted,bolted or welded attechment etc complete all as specified and directed.

S&F MS screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but n exc10cm long and dia of neck 16 to 20mm etc complete all as specified and directed.

Material and labour for preparation of new and previously un-treated steel surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for 20mm thick cement mortar 1:6 screed bed on concrete floor for laying tiles etc complete all as specified and directed.

M&L for Chequered cement concrete tiles with grey cement and pigment of size 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulators, sockets, etc. to be measured separately) and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as directed by the Engr-in-Charge.

Taking down carefully MCB DBs SP/TPby unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed.

Material and labour for concealed point wiring with 1.5 Sqmm PVC insulated and sheathed multi stranded (FRLSH) flexible copper conductor cable in and incl rigid PVC conduit concealed /PVC surface conduit with sunk cast iron/pressed steel terminal boxes of adequate size with suitable thickness hylum laminated sheet, cover of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm (FRLSH) PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire(green colour) to common earth dolly complete all as specified and directed. Note: a) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc (b) On RCC roof ceiling PVC conduit shall be provided on surfaces for fan etc with proper fixing clips all as directed

All as per serial item No 105 here in before but for one 3 pin 5 Amp socket outlet on independent board.

All as per serial item No 105 here in before but for one 3 pin 5 Amp socket outlet on same board.

All as per item No 105 here-in-before but using 2.5 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board.

Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, one way with white colour complete all as specifed & directed.

Supply and fixing of switch socket outlet combination 3 Pin, 5 Amps, 240 volts flush type (non shuttered) with white colour complete all as specified & directed.

Supply & fixing of socket 3 pin 5 Amps 240 Volts flush type (non shuttered) with white colour complete all as specified and directed.

Supply and fixing switch socket out let combination multipurpose 3 pin, 5/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) with white colour complete all as specified & directed.

Supply and fixing ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals, complete all as specified & directed.

Supply and fixing ceiling fan regulator electronic, Deluxe, rotary, step type, 120/280 V, complete all as specified & directed.

Supply and installation of new metering board powder coated single door fabricated with 1.6 mm thick CRCA sheet suitable for mounting 01No of TPN MCB and 06 No 6 to 32 Amps MCB with IP 43 protection, Glazed door, isolated neutral bar, insulated bus bar assemblyus bar for neutral and earth continuity arrangement of size not less than 50cm x 50cm x 15cm including taking down of old Unserviceable TPN or meter box and making good of previous surfaces i.e plaster work, painting of surfaces as in previous surfaces)

Supply and fix in repairs of MCB SPN DB 8 way double door,IP 43 protection,Glazed door, isolated neutral bar,insulated bus bar assembly,mechanical strength of IK09, complete all as specified and directed

Supply and fix in repairs of MCB SPN 32 Amps 'C' Series 10 KA,240 volts complete all as specified and directed.

Supply and fix in repairs of MCB SP 6 to 32 Amps 'C' Series 10 KA, 240 volts, complete all as specified and directed.

Supply and fixing in repair of MCB Distribution board SPN 4 way double door for mounting SPN/SP MCBs as incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet, fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43-IK 09 with metal door complete all as specified and directed by Engr-in-Charge.

Supply and fixing Bulb holder angular PVC/Polycarbonate suitable for batten fittings, complete all as specified and directed.

Supply and fixing LED Inverter Batten fitting 1x18 watts including Tube rod, 230 Volts, bipin holders connector block etc.complete with all accessories internally pre-wired and including provision of PVC round block 7.5cm dia and 2 cm in depth (2 Nos) for mounting the fittings and electrically connecting with three single core 23.0.0076 PVC insulated multistranded copper conductor flexible cable from ceiling rose to light fitting, complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to earth lead wire 4 mm dia by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and earth works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material, complete all as specified and directed.

Taking down aluminium submain wire along with damaged casing caping / PVC conduite pipe from the wall roof or floor and making good distrubed surface, complet all as specified and directed.

S&F sub main wiring concealed with three run of single core (FRLSH) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit of adequate size with proper colour coding and making electric connections, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as specified and directed. Note :- (i) Rates are deemed to be included chases of conduit and sinking for boxes cutting and making holes in wall/floor for passing in or through conduit (ii) Three run of 6.00 sqmm single core (FRLSH) PVC insulated copper conductor cable and one run of PVC conduit of suitable size will be measured as a one unit.

Supply only LED Inverter bulb of 9 Watt (Warm white), complete all as specified and directed. Make- Havells B 22 CDL or equivalent to Philips/ CG/Havells

Supply and fixing of 35W LED building security light fittings in aluminium PDC housing, toughened glass cover,individual LEDs with secondary optics, covered with IP66 protection with in built surge protection of minimum 5 kV and repair/replacement warranty of minimum 3 years. Make: Surya SLE UL 45W IP66 LXN or its equivalent in Philips/GE

Supply and fixing of 45W LED building security light fittings in aluminium PDC housing, toughened glass cover,individual LEDs with secondary optics, covered with IP66 protection with in built surge protection of minimum 5 kV and repair/replacement warranty of minimum 3 years. Make: Surya SLE UL 45W IP66 LXN or its equivalent in Philips/GE

S&F for 32 mm dia GI tubing light grade bracket over all 1.2 mtr length with cutting as required and bend to shape with flat iron clamp of size 32 mm 2 Nos, suitable size of nut bolts and washers complete for fixing street light fittings on electric poles including taking down old unsv / fully rusted existing unsv one complete all as specified and directed.

Supply and fixing of elecric geyser of size 25 Ltrs vertical type, BEE 5 star rated, AC single phase 230 volts finishing, including PVC connection pipes, nuts and bolts, complete all as specified and directed.

Supply and fixing of elecric geyser of size 50 Ltrs vertical type, BEE 5 star rated, AC single phase 230 volts finishing, including PVC connection pipes, nuts and bolts, complete all as specified and directed.

M&L for cutting of circular hole at any type of wall suitable size for fixing of exhaust fan of size 250mm sweep, grouting 04 Nos 100mm long 12mm dia stud bolt including,making good to disturbed surfaces of wall to match as per the existing colour, complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 250 mm sweep fiber body with louver, complete all as specified and directed.

S&F sub main wiring concealed with three run of single core (FRLSH) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 1.5 Sqmm drawing into and including PVC non metallic rigid conduit of adequate size with proper colour coding and making electric connections, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as specified and directed. Note :- (i) Rates are deemed to be included chases of conduit and sinking for boxes cutting and making holes in wall/floor for passing in or through conduit (ii) Three run of 1.5 sqmm single core (FRLSH) PVC insulated copper conductor cable and one run of PVC conduit of suitable size will be measured as a one unit.

Supply and spread sand in trenches as sand cushioning to underground cable for protection with fine river sand and provide required cover after punning down complete all as specified and directed. Note : For the purpose of payment only punned thickness will be measured. (Note: Thickness of sand cushion after punning down will be measured and paid.)

M&L for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of size 230x115x75 mm to cover LT underground cables, laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed.

S&F in repair 40mm bore GI tubing “light grade” in trenches/ on pole for protection of cables, complete all as specified & directed.

Supply, laying connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty), aluminium stranded conductor 1100 volts grade size 16 sqmm 4 core, laid through duct/ pipe / in trench etc. including cable glands & lugs complete all as specified and directed.

Supply, laying connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty), aluminium stranded conductor 1100 volts grade size 10 sqmm 2 core, laid through duct/ pipe / in trench etc. including cable glands & lugs complete all as specified and directed.

Taking down and refixing, old existing servicable MCB SPN DB's of any type and refixed with concealed wall including make good wall surface by plastering, painting and civil work, included complete all as specified and directed.

Taking down and refixing, old existing servicable MCB's SPN, SP, TPN, DPN any other size/ type and refixed including make good plastering, painting and civil work deemed to be quoted rate complete all as specified and directed.

Supply and Fix mirror light of 9 Watt (Warm white), complete all as specified and directed. Make- Havells LHLDESAARANB020 or equivalent to Philips/ CG/Havells

Supply& fixing ceiling fan of 1200mm working on BLDC Technology without remnote with all its accessories including taking down unserviceable ceiling fan with all accesories & submitting back to MES Store yard, complete all as specified and directed.

Supply, installation, testing and commissioning of size not less than 1.0m x 0.9m x 0.80 m , outdoor cubical type factory made (CPRI approved), single hinged type door for individual MCCBs rubberised gasket, front & back side openable type with locking arrangement (screw type), fabricated of CRCA sheet 3.15 mm thick supported on 50 x 50 x 6 mm angle iron and Tee section frame dust and vermin proof complete with aluminium bus bar 4 Nos, 400 Amps rated capacity mounted on porcelain insulators totally enclosed chamber for protection 3 phase 415 volt with suitable capacity aluminium bus bar and interconnection between MCCB and bus bar will be done by aluminium strip only duly mounted on PCC floor and with suitable size of bolts, nuts & wahsers. Panel board shall be powder coated and angle iron frame painted with black synthetic enamel paint over a coat of red oxide primer complete, connecting existing cables with suitable size glands and aluminium lugs to accommodate and including the following :- Incoming :- (a) MCCB, 4 Pole, 200A, 415 V, 35 kA.- 01 No. (b) LCD multifunction meter - 01 No (c) CTs 320/5 A - set of 3 (d) Phase indicator lamps (RYB) -set of 3 (e) Aluminium bus bar 4 strip of 600 Amps (f) Internal connection by aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etc Outgoing :- (a) MCCB, 4 Pole, 63 A, 415 V, 35 kA - 03 Nos (b) MCB, TPN, 40 A, 415 V, 16 kA - 01 Nos.

Schedule of Credit

M/S SUBHASH BHATTACHARJEE

M/S D.R enterprise

M/s UB Enterprise

Lyngdohs Construction Company And Associates