Provision of Digital Axle Counter in parallel with overlap Track circuit at IB over Khurda Road Division.

A-EXECUTION OF SIGNALLING WORKS: RATES ARE INCLUSIVE OF:1.All

B-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All

C-SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE

4.Transportation of released materials from one site to another site or store of concerned SSES/(In-

charge) or as advised by Sr.DSTE/KUR.

Item- 1 EXECUTION OF SIGNALLING WORKS

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply, Installation and Commissioning of Set 32.00 695020.00 22240640.00

Single Section Digital Axle Counter (SSDAC)

Phase Reversal type as per RDSO Specification

No. RDSO/SPN/177/2012 (Version-3) and latest

if any along with Installation accessories as

given below. (i) Single Section Digital Axle

Counter Phase Reversal type as per RDSO

Specification No. RDSO/SPN/177/ 2012

(Version- 3) and latest if any. Each Set consists

of following: - a) High frequency TX Coil and

RX Coil with Cables (Each Set consists of Web

Mounting type TX Coil 2 Nos., RX Coil 2 Nos.

along with 10 mtrs. Cable) = 2 Sets. One Set

will be submitted with SSDAC during

installation and one Set will be kept as Spare

with the Consignee. b) Track Side Digital Axle

Counter unit 2 nos. c) VR Box 2 Nos. Each duly

wired with 2 nos. of 24V, 6F/6B, 1000ohm Q

type relays. d) Clamp with deflector plates and

hardware etc. 4 nos. e) Reset Box 2 nos. f) All

other Equipment/Subsystem/literature as

available in Standard Set as per RDSO

Specification. (ii) Mushroom/Location Box

suitable for housing Track side equipment = 2

nos. Inspection by RDSO.

2 2 Excavation of trenches of 1.0 Meter depth and Kilometre 18.00 88821.00 1598778.00

width 0.3 Meter detailed below including

clearing of roots and trees etc. for all types of

soil. This work also includes covering of cables

laid in trench and backfilling, ramming,

consolidation of soil as well as disposal of extra

soil after cable is laid as specified in

Guidelines on Signalling Cable laying given by

RDSO and any latest circular issued by

CSTE/ECoR/BBS. Note: Before refilling of the

trenches, the cable laid are to be tested and

recorded for its insulation value and after

satisfaction of site Engineer the refilling

process should start and after monsoon the

route is to be attended for backfilling the rain

cuts, wash out of soils where ever found.

3 3 Supply & Erection of Polyolefin Cable Channel Numbers 6000.00 2120.02 12720120.00

of size width (Int/Ext) 240/340mm, Length

approx. 1 Meter, weight per mtr. Should be not

less than 8 Kg (Top & bottom). Material-

Polyolefin-Engineering plastic with fire

protection class K-1 in accordance with DIN

53438 part-II, breaking load Minimum >=12

Kilo Newton or latest at room temperature for

laying signalling/Telecom/Power Cables,

Channel attachable to each other with male

female swallow tail connectors and having

suitable detachable cove. Technical

specification and testing Parameter /Procedure

as per RDSO- Ref No. STC/Cable-laying

practices Vol-IV dated 09.05.2018. Inspection

of polyolefin cable channel by RITES.

KHURDA ROAD DIVISION-S AND T/ECOR

4 4 Excavation of trenches in all kinds of soils Metre 500.00 335.00 167500.00

including soft rocky area and clearing of track

etc. to a depth of 1.0 M and width of 0.3 M for

track crossing /pucca road/level crossing

gate/platform/station circulating area or any

other place as advised by site Engineer

including transportation and laying of

DWC/RCC/Split RCC/G.I. pipes with or without

coupler. This includes repairing of track/pucca

road/level crossing gate/ platform/station

circulating area surface to original position by

ramming and concreting wherever required

soon after the work is over. DWC/RCC/GI pipes

shall be supplied by the Railway. DWC pipes

wherever required shall be supplied in 6 Mtr.

length and shall be cut to size as per

requirement. All other materials including

cement are to be supplied by the contractor.

5 5 Excavation of trenches including clearing of Metre 1000.00 255.00 255000.00

roots of trees etc., in rocky area up to a depth

to be indicated by Railway Engineer at site as

per the site condition [Minimum 0.6 meter]

and width 0.3 Mts. at the bottom. This includes

concreting & plastering as per the instructions

of site Engineer and complete back filling by

digging earth from a lead of 30 Mtr. In case

0.8-meter depth or higher is achieved no

concreting is required, otherwise concreting

up to 100 mm thickness should be done. All

materials required for the above works shall

be supplied by the Contractor.

6 6 Cutting of masonary floor/walls at station Numbers 20.00 6108.00 122160.00

building/ signal goomty/ Gate lodge at a depth

of 0.5 mtr. to 1.0 mtr at places to be indicated

by site Engineer for entering of cables inside

the building. Only G.I pipes supplied by

Railway and all materials as clamps, bolts &

nuts as instructed by site Engineer supplied by

tenderer. This includes repairing of masonary

floors/walls after the cables are taken inside.

Cement, Sand required for the work shall be

supplied by the tenderer and also

transportation of G.I Pipe from Store by the

7 7 Transportation and fixing of perforated G.I. Metre 300.00 2653.00 795900.00

Pipes on bridges, culverts, drains or in

trenches or any other place as per instruction

of site Engineer with clamps at 1.5 mts.

interval on steel girder bridges or at places

advised by site Engineer. This includes

supplying of G.I. Pipes, 80/100/150 mm dia.

Specn. No. IS:1239/2004, or latest medium

gauge with threaded collars (Make -TATA

/JINDAL) by tenderer. This also includes 100

mm thick concreting on GI pipes as required

and instructed by site Engineer and all other

materials required for the work shall be

supplied by the tenderer. Note: The G.I. pipe

shall be perforated by drilling 7 mm dia holes

length wise in zig-zag manner staggered at a

distance of 300 mm. G.I. Pipes before and

after perforation and bridge fixtures supplied

by the tenderer will be inspected by

representative of Railway before use. The

bridge fixtures will be supplied by tenderer for

fixing of GI pipes on girder bridges only. (1) GI

pipes of 100 mm Dia

KHURDA ROAD DIVISION-S AND T/ECOR

8 8 Laying of Signalling/4 Quad/ 6 Quad/ Power Kilometre 70.00 24389.00 1707230.00

Cable/Telecom cables/ Jelly filled cables of all

sizes in excavated trench, through

GI/RCC/DWC pipes etc. wherever required.

This includes transportation of cables from the

stores to work site and transportation of empty

cable drums with left over cables from site to

the stores at. The length of cable laid includes

the length of cable coil for termination

purpose. NOTE: The cables are to be carefully

handled during loading, un-loading and

transportation to work site. Any damage found

in the cable after final testing, in view of

mishandling of cables, shall be made good by

the Tenderer. Cable should be maggered

before and after laying and recorded in a

register and submitted to the site Engineer.

9 9 Transportation, excavation of pit, casting of Numbers 40.00 19438.00 777520.00

foundation, plastering and erection of Steel

Apparatus case (full size) with fixing of E-Type

lock, wiring, cable entry, termination

clamping, filling cable pit with sand, painting

and lettering etc., as per Drg.No.

S&T/CON/SK/16. This includes earth work

and/or masonry work required for securing the

apparatus case as per site condition. Railway

will supply apparatus case with 'E' type lock

only from Railway stores at. Tenderer will

supply all wiring materials, PBT Terminals,

fuses, fuse blocks, bus bars, hylum sheet ISI

mark [6mm thickness], wood plank board of

good quality [minimum 3/4" thick, Cement and

transport all the materials to site of work at his

own cost. The wiring materials such as wire

coils, PBT terminals, fuses, fuse block, etc.

should be used from RDSO approved sources.

1) Modification of inside arrangement of

Apparatus cases if required for fixing of

relays/transformers etc. shall be done by the

contractor. Extra shelf, if any, shall be

deposited to the Railway stores by the

contractor. 2) All cables shall be terminated by

providing copper eyelet of suitable size. Note:-

(i) If location box foundation is available at site

20% of the cost is to be deducted. (ii) 40%

payment shall be released after erection of

location boxes.

10 10 Supply, Transportation and Installation of Numbers 40.00 12306.00 492240.00

earth electrode (make TATA or Jindal as per

Rly. practice) including MS flat for signalling

equipments on lever frame, apparatus cases,

signal, relay racks, cable termination rcak,

block instrument etc. (supply & installation of

earth electrode as per drawing no.

RE/S&T/DRG/Tender/SK/398/94 for apparatus

cases, signal post & other equipments as per

instruction on earthing of S&T equipment.

Laying of earth lead mild steel flat of size

35mmx6mm and fixing of lead MS flat (make

TATA/Jindal or Similar) to earth electrode and

lever frame, signal post & apparatus cases as

per Drg. No. CORE/S&T/ALD/SK/591/2008,

592/2008 and 593/2008 respectively and

instructions on earthing at S&T equipment and

providing cement enclosure for earth

electrode as per drawing no.

RE/S&T/Sig./Tender/SK/13/85 Alt. A) NOTE:

This includes testing of earth value and

indicating the same on the Earth enclosure by

paint. Inspection by representative of

KHURDA ROAD DIVISION-S AND T/ECOR

11 11 Alteration of wiring in existing apparatus cases Numbers 40.00 3583.00 143320.00

full/half. This includes supply of all materials in

connection with alteration in wiring. All the

materials shall be supplied by the contractor

at his own cost. This includes entry of cables,

sand filling and masonry work involved.

Lettering and painting to be done by the

contractor at his own cost. Railway shall

supply only relays and relay bases.

12 12 Alteration of wiring in existing Relay rack/ CT Numbers 40.00 28281.00 1131240.00

rack/composite relay rack. This includes supply

of all types of wires, eyelets, nuts & bolts,

bunching material, ferrules, ARA terminals,

fuses & fuse blockes by the contractor at his

own cost. Lettering & painting to be done by

the contractor at his own cost. Wire (RDSO

Approved Sources) to be inspected by the

representative of Railway before use.

13 13 Fixing of relay bases and wiring, bunching, Per Relay 200.00 783.00 156600.00

fixing of relays, wiring in Old relay

racks/location box and also carrying out any

alteration in existing relay rack duly wiring

and connecting New to old and Old to old

relays by standard wires (RDSO Approved

Sources) as per Circuit diagram. Fuses of

bases, condensers, ND fuses, LED indicator &

its wiring for relay rack. All materials required

for this work will be supplied by the contractor

from RDSO Approved Sources. Relays with

accessories will be supplied by the Railway.

Schedule B-SUPPLY OF SIGNALLING MATERIALS: RATES ARE INCLUSIVE OF:1.All taxes., 2.Supply of

sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of materials to site.,

4.Transportation of released materials from one site to another site or store of concerned SSES(In

charge) or as advised by Sr.DSTE/KUR

Item- 2 SUPPLY OF SIGNALLING MATERIALS.

S No. Item Description of Item Unit Qty Rate Amount

1 1 Supply of Single Section Digital Axle Counter Set 6.00 588820.00 3532920.00

(SSDAC) Phase Reversal type as per RDSO

Specification No. RDSO/SPN/177/2012

(Version-3) and latest if any along with

Installation accessories as given below. (i)

Single Section Digital Axle Counter Phase

Reversal type as per RDSO Specification No.

RDSO/SPN/177/ 2012 (Version- 3) and latest if

any. Each Set consists of following: - a) High

frequency TX Coil and RX Coil with Cables

(Each Set consists of Web Mounting type TX

Coil 2 Nos., RX Coil 2 Nos. along with 10 mtrs.

Cable) = 2 Sets. One Set will be submitted

with SSDAC during installation and one Set will

be kept as Spare with the Consignee. b) Track

Side Digital Axle Counter unit 2 nos. c) VR Box

2 Nos. Each duly wired with 2 nos. of 24V,

6F/6B, 1000 ohm Q type relays. d) Clamp with

deflector plates and hardware etc. 4 nos. e)

Reset Box 2 nos. f) All other

Equipment/Subsystem/literature as available

in Standard Set as per RDSO Specification. (ii)

Mushroom/Location Box suitable for housing

Track side equipment = 2 nos. Inspection by

RDSO. (NOTE: The material is to be used as

spare, so there is no need of installation &

commissioning.)

KHURDA ROAD DIVISION-S AND T/ECOR

2 2 Supply of Relay AC Immune, plug-in type, Numbers 200.00 6428.00 1285600.00

style 'QNA1', Neutral line, 24V DC 8F/8B

contacts, Front and back contacts metal to

carbon, complete with plug board, retaining

clip and connectors conforming to BRS : 931A,

IRS : S - 60, IRS : S - 34, IRS : S-23 (As

applicable). Interlocking code: ABDGH.

Inspection by RDSO.

3 3 Gallant Power AC to DC converter Input-230V Numbers 64.00 40120.00 2567680.00

AC, Output-(-) 48V DC/10A(500Watt) with built

in diode, digital volt/Amp meter and all

required protection circuits. (Model No-PS-

4810RV2). Inspection by RITES.

4 4 Supply of double walled corrugated pipe 6 mtr Numbers 90.00 4117.00 370530.00

in length, 120 mm outer dia and 103 mm inner

dia, with one suitable coupler conforming to

RDSO Specification No. RDSO/SPN/204/2011

Version 1.1 Amdt 1 or latest for underground

cable protection. Colour-Orange. Note: If

required, the DWC pipe shall be supplied split

in two halves. Inspection by Representative of

5 5 Supply of Steel Apparatus case 'large Size' as Numbers 13.00 42507.00 552591.00

per Drg. No - CON/SK/1/1/86 and Spec.No.

IRS:S-10/78 (adv) with latest amnd. with "E"

type lock and key of ward No-32 with handle.

Inspection by RITES.

Schedule C-SUPPLY & EXECUTION OF DRAWING WORK : RATES ARE INCLUSIVE OF:1.All taxes.,

2.Supply of sundry materials like nuts, bolts, washers, sand, stone chips., 3.Transportation of

Schedule materials to site., 4.Transportation of released materials from one site to another site or store of

concerned SSES/(In-charge) or as advised by Sr.DSTE/KUR. (Item Directory - Not Applicable) (Item

Directory - Not Applicable) (Item Directory - Not Applicable)

Item- 3 SUPPLY & EXECUTION OF DRAWING WORK

S No. Item Description of Item Unit Qty Rate Amount

1 1 Compilation, preparation, correction, updating, Per Page 400.00 25.00 10000.00

printing and supply of Final station working

rules with contractor's stationery, tools, plants

and materials. Note: Final SWR to be

submitted in 2 sets for each station. NOTE: Per

page should be treated as Page.

2 2 Alteration of Existing Location Box Drawings Sheet 100.00 451.00 45100.00

(Including Contact Analysis, Fuse Particulars

etc) and submission of Three paper copies for

approval. NOTE: Sheet should be treated as

3 3 Alteration of Existing Goomty Drawings Sheet 500.00 901.00 450500.00

(Including Relay Disposition Chart, Contact

Analysis, Fuse Particulars, CT Rack Particulars

and Floor Plan etc) and submission of Three

paper copies for approval. NOTE: Sheet should

be treated as per sheet.

4 4 Supply of Original Tracing in A-3 Size. NOTE: - Sheet 600.00 71.00 42600.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size. NOTE:

Sheet should be treated as per sheet.

5 5 Supply of Amonia Prints in A-3 Size. NOTE: - Sheet 1800.00 19.00 34200.00

For Drawings larger than A-3 Size, payment

shall be made in multiples of A-3 Size. NOTE:

Sheet should be treated as per sheet.

6 6 Alteration of Existing SWRD & submission of Station 16.00 2596.00 41536.00

Three paper copies for approval For a Four-

Line Station. NOTE: Station should be treated

as per station.

KHURDA ROAD DIVISION-S AND T/ECOR

7 7 Design of Location Box Drawings (Including Station 16.00 1763.00 28208.00

Contact Analysis, Fuse Particulars etc) and

submission of Three paper copies for approval

For a Four-Line Station. NOTE: Station should

be treated as per station.

8 8 Supply of Original Tracing of Location Box Station 16.00 2644.00 42304.00

Drawings (Including Contact Analysis, Fuse

Particulars etc) after incorporating all the

corrections. For a Four-Line Station. NOTE:

Station should be treated as per station.

9 9 Supply of Eight sets of Amonia Print of Station 16.00 2821.00 45136.00

Approved Completion Location Box Drawings

(Including Contact Analysis, Fuse Particulars

etc). For a Four-Line Station. NOTE: Station

should be treated as per station.