REPAIRS TO AREA DRAINAGE INCLUDING COVERS AND DESILTING AT DIGLIPUR

Amount

Dismantling of brickwork or stone/ boulder masonry or PCC block masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks with minimum compressive strength of 50 Kg/Sqcm, exceeding 10 cm in width and setting in cement mortar 1:6 complete.

Taking down cement plaster on brick or stone walls, concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L for rendering 10mm thick in cement and sand mortar 1:6 on fair faces of brick work or concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and facilitate to cut reinforcement and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L for RCC M-30 (design mix) (using 20mm graded crushed granite stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

M&L for RCC M-30 (design mix) (using 20mm graded crushed granite stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses.

M&L for providing steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for flat rough finished surfaces of concrete all as specified.

M&L for providing steel formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for flat fair finished surfaces of concrete all as specified.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L for 75 mm thick PCC Type D2, 1:4:8 (using 40 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. finishing surfaces of concrete even and rough complete all as specified.

M&L for chequered colour cement concrete tiles 20cm x 20cm x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry on floors/ steps, over and including screed bed or bedding layer of 15 mm thick in CM 1:6 complete.

M&L PCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) as in copings, cills, benching of manholes, kneelers, apex stones, bed plates, levelling course, kerbs water troughs and the like including use of formwork, weathering, slightly rounded or chamfered angles and throating.

M&L for PCC Type B2, 1:2:4 (using 40mm graded granite stone aggregate) as in surface channels and drains complete.

M&L precast RCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in CM 1:6, including necessary formwork complete. Note: Reinforcement shall be measured and paid separately.

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for high yield strength deformed TMT steel bars 5 mm to 10 mm dia cut to length, bent to shape required, as in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. (Inner girth only shall be measured).

Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. (Inner girth only shall be measured).

Desilting of storm water drains including dewatering and removing soil/ muck to outside the MD land and depositing where directed.

MOHAMMED SAFIQUE

kakolil trade agencies

M/s S U Enterprises

RADHA GOVIND CONSTRUCTION

LANDMARK ENGINEERS & CONSULTANTS