Renovation Work of Upper Primary School Launa in Block Jalaun of District Jalaun under Smart School Program

TRUSS SIZE- 8.00X6.00 Mtr. Clearing Jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles

Providing and laying in position specified grade of reinforced cement concrete. Excluding the cost of centering, shuttering finishing and reinforcement- All work up to plinth level 1:1.5:3 cement, coarse sand and 20mm gauge stone grit including all complete

Centering and shuttering including strutting, propping etc. and removal of form for :Foundation, footing, bases of columns etc. cocrete shuttering.

Centering and shuttering including strutting, propping etc. and removal of form for : (c) Lintels, beams, plinth beams, girders, bressumers and cantilevers

Rainforced cement concrete work in walls, including attached pilasters butresses, plinth and string courses, fillets, columns, pillare, piers, abutments, posts and struts etc. above plinth level up to floor fice level, excluding cost of centering, shuttering finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone aggregate 20mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for :(d) Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common bumt clay FPS bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Plaster 12mm thick with cement, fine sand mortar in propostion of 1:4 in fair side of wall i/c all complete as directed by engineer in charge etc.

Steel rainforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Theme mechanically treated bars of grade Fe-500 D.

Structural steel work riveted bolted in bult up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing corrugated G.S. sheet roofing including vertical/ curved surfacd fixed withpolymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and GI limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 0.63 mm thick with zinc coating not less than 275 gm/.

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J of L hooks, bolts and nuts 8mm dia GI limpet and bitumen washers complete 0.63 mm thick with zinc coating not less than 275 gm/ sqm

Printing steel work with Deluxe Multi surface paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10sqm over an under coat of primer applied @ 0.80 ltr/ 10sqm of approved brand and manufacture.

Finishing wall with water proofing cement paint of required shade New work (Two or more coat applyied of 3.84 kg/ 10sqm)

Excavating, supplying anf filling of local earth by mechanical transport upto a lead of 5km also including ramming and eatering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc.complete

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

1:5:10 (1 Cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural soures)

Laying of 80mm thick cement concrete paver block (interloc brick) with 40mm thick stone dust including preaparation of base and joint filling all complete

Sanitory work Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 (including angle valve for WC flushing cistern, jet & kitchen sink) 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing & fixing PVC waste pipe for sink including PVC waste fittings Complete Flexible Pipe 32mm Dia

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. For Internal Toilet 15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal bore

25 mm nominal bore

Providing and fixing GI pipes complete with GI fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on Wall Terrace loop & Tank Filling Pipe 20 mm nominal bore

25 mm nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 20mm diameter pipe

25mm diameter pipe

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm dia (for rain water)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia

Providing, fixing, jointing and testing , of PVC Nahani Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge. 110mm x 75mm (Toilet)

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating (including balcony)

ELECTRICAL WORKS Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group - C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Extra for fixing the Louvers/ shutters complete with frame for exhaust fans of all sizes.

Supply of LED 4ft Batten with a nominal system lumen output of 2000 lumens and a minimum system efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of 25,000 burning hours at L70. The luminaire should have a color temperature of 4000K and CRI>80. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.9. The luminaire housing should made of extrusion Al with a PC diffuser. The total power consumption should not exceed 21W (including driver).Including connection with 1.5 sqmm FRLS PVC insulated copper conductor.

Supply of Surface mounting round 6 Watt 10 Watt , LED Down Lighter, suitable for 24Hr Continuous Operation, 660-1100 system lumens, 110lm/W, PF>0.95, THD <10% at full load, CRI>80, Avg Life Class 50000Hrs @L70, complete in all respect.

Supplying of LED mirror light luminaire with 10W watt complete with electronic ballast, lamp including connection etc. complete as required, Including connection with 1.5 sqmm FRLS PVC insulated copper conductor.

Supplying of 9 Watt 4 Star LED Wall Light Blub complete in all respect.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 1200 mm sweep ceiling fan

Supplying of following size exhaust fan complete with gravity louver and connection with 3 core flexible wire as required. 300mm EXHAUST FAN

Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required 40 amps TP MCB

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. As required. 25 amps

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal)

REQUIREMENT ITEM SITC of 4 kw off grid solar panel with battery ( 4000 watt panel , 8 nos 150 ah 12 volt battery , 4 kw invertor battery rack invertor stand , fixing frame of solar plate , 20 point wirring changeover etc complete )

Providing and installation projector Epson/ similar

Provision for smart board/ Digital Board Samsung/ similar for Teaching & Presentations Interrative Display. (Touch Pen type, Screen Size 55* / 65*). (As per Market Rate for Estimate Purpose).

Supply of wooden Table and Chair Set

Provision for podium stand wood, height 48.8 in pulpits for churches, Reception Desk, Lectem with spacious Drawer for Hotels, Seminara, weddings and classroom (Colour: D , size: 60x42x12cm) with speaker.

Supply of Kids study plastic table and chair set class room 1-2 Multi purpose (as per market rate for estimate purpose.)

Supply for school Bench and Desks class room 3-5 (Size 1250x775x595mm) (as per market rate for estimate purpose.)

Supply for Almirah

Supply & fixing of Blue star or similar Stainless Steel water cooler with inbuilt aquaguard RO Purification 50 Liter.

Supply for Nilkamal / Similar Plastic 120 Ltr Wheel Garbage Dustbin (as per market rate for estimate purpose.)

Supply of Conference Meeting for Office Tabel Luxury Modern Design and made in High-quilty Ply and solid wood with veneer and PU polish & make a great look in your office- size 10x4 Ft: L120x W48 H30 inch. (as per market rate for estimate purpose.)

Supply of Revolving Chair (As per market Rate for estimate purpose)

Supply of Visitor Chair (As per market Rate for estimate purpose)

Provision for Library Furniture Racks. (As per market Rate for estimate purpose)

Provision for HP 60.5 cm (23.8) All in one Desktop PC 24-cr0903in- intel core TM i3-1315U (up to 4.5 Ghz with intel) Turbo boost Technology, 10 MB L3 cache, 6 cores, 8 threads.

S/F Play Mild steel Doubler sheeter swing (For estimate purpuse)

S/F Play Ground wave slide (For estimate purpuse)

S/F Play Single Seesaw (For estimate purpuse)

S/f Play kids Merry Go-Round (for estimate purpuse)

S/f Play Volleyball Pole with net & Ball (for estimate purpuse)

GST Extra as per Applicable

Please Enable Macros to View BoQ information