SPECIAL REPAIR BLDG NO T-6, PROVN OF TOILET BLOCK NEAR BLDG NO P-203, ADDN/ALTN IN BLDG NO P-37 AND P-38 AT MT LINE FOR JCOS AND OR MD ACCN UNDER AGE B/R-II (WEST) AND PROVN OF LT VEH PARKING SHED FOR OFFRS IN FRONT OF BLDG NO T-15 UNDER GE (WEST) DE

Amount

M&L for Brick work with sub class 'B' old size burnt bricks straight or curved on plan exc 6 M mean radius built in cement mortar 1:6 all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of priming with alkali resistant priming paint complete all as specified and directed.

M&L for preparation of new surfaces and applying two coats of cement base paint over and including a coat of priming with alkali resistant primimg paint on external surfaces of walls complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams(lintal beam), beams haunchings, girders, bressummers, lintels, cantilever, shelves including supports, overhangs, etc also splays between floors and beams etc rough finished flat surfaces of concrete all as specified and directed by Engr-in-Charge.

M&L for RCC(nominal mix) (1:2:4) type B1 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed by Engr-in-Charge.

M&L for Mild Steel TMT bars 10 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9 mm dia complete all as specified and directed by Engr-in-Charge.

Ditto all as per item No 6 above but 5 mm dia and over upto and including 10 mm dia in stirrups ,spacers and binders complete all as specified and directed by Engr-in-Charge.

M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges(butt hinges medium weight cold rolled mild steel fixed with screw or welded) or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming Fe.290.Gde-E-165 complete all as specified and directed.

S&F 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick second class hard wood, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, sizes of members of shutters as specified in SSR part-I section 8 clause 8.24 supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge.

S&F 125mm long aluminium handles cast type anodised ISI Marked complete all as specified and directed by Engr-in-Charge.

S&F Aluminium alloy, anodised, sliding door bolt 250mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge.

S&F 75 mm Floor door stopper having overall length of cover plate of aluminium alloy body and tongue, anodized with hard drawn steel spring, double legged including vulcanised rubber piece complete all as specified and as directed complete all as specified and directed by Engr-in-Charge.

S&F 200 mm,Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new wooden surfaces and painting two coats of synthetic enamel paints over and including a coat of pink primer exc 10cm width or girth complete all as specified and directed.

M&L PCC (1:3:6), type C-1 using 20mm graded crushed stone aggregate as in filling of steel chowkhats complete all as specified and directed.

Dismantling of floor hearth and wall tiling incl mortar beding and throw rubbish out the premises as directed by the Engr-in-Charge.

M&L for glazed coloured designer ceramic tiles of size 450x350x7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over and including 10mm thick rendering as a backing coat (rough finished) in cement mortar (1:3) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-Charge.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with pigment with colour of tiles over and including screed bedding 15mm thick in CM(1:4) complete all as specified and directed by Engr-in-Charge.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with pigment with colour of tiles over and including screed bedding 15mm thick in CM(1:4) complete all as specified and directed by Engr-in-Charge.

M&L powder coated aluminium 50 micron anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5 mm thickness and of shutter size 40mm x 18mm (with 9.00 mm interlocking legs) x 1.45 mm thick section, including frame size 100mmx44mmx2mm thick, including 95mm aluminium handle with spring lock, stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4 mm and fixed with steel wire stapples 5mm thick plain glass including necessary fitting/fixture/aluminium snap beads, EPDM rubber , neoprene packing, rollers to slide track window complete all as specified. (Note : Measurement shall be taken clear opening ie out to window frame as a whole including all fittings and fixtures and no extra shall be paid separately. Cost of glass and wire cloth included herein complete all as specified and directed by Engr-in-Charge.

S&F for powder coated aluminium grill of powder coating of minimum 50 micron with aluminium mesh of size 50 mm x 50mm with square tube solid 6mm thick including aluminium channel of suitable size to the aluminum window complete all as specified and directed by Engr-in-Charge.

Taking down of cement mortar plaster of any description and preparation of surfaces for receiving new plaster including racking out of joints complete all as specified by Engr-in-Charge.

M&L for 15mm thick rendering with cement mortar (1:4) on brick work or concrete surfaces on wall, finish the surface even and smooth without using extra cement as whole etc complete all as specified and directed.

M&L for 5mm thick rendering with cement plaster (1:3) on ceiling surface finished even and smooth without using extra cement as whole etc , complete all as specified and directed.

M&L for Cutting holes in brick wall exc half bricks but not exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed by Engr-in-Charge.

M&L for Preparing new surfaces of steel of any description,not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar, removal of rubbish beyond MOD land complete all as specified and directed.

M&L for kota stone slab 20-25mm thick of size 550x550 mm as in flooring , tread and riser of steps, skirting, dado and pillars laid over 20mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shed of the slab including rubbing and polishing complete all as specified and directed.

M&L for praparing old surfaces and applying one coat of Oil Bound Distemper on wall surfaces all as specified and directed by Engr-in-Charge.

M&L for praparing old surfaces and applying one coat of cement based paint on wall surfaces including proper curing all as specified and directed by Engr-in-Charge.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

Removing mud phuska/soil material exc.250 m but n exc. 500 m and depositing where directed.

M&L for brushing neat cement slurry with 3 kg of cement per square metre complete all as specified and directed.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified and directed.

M&L 10 mm thick screed bed or bedding layer of mortar in CM(1:4) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface. Note: WPC shall be measured and paid separately

Supply only water proofing compound.

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric(wt. not less than 150 gms/sqm) land on primed surface by forced apllication complete all as specified.

Supply and fixing Heat Resistant Terrace Tiles(300mmx300mmx20mm) with SRI(solar refractive index)>78,solar reflection>0.70 and initial emittance>0.75 on waterproof and sloped surface of terrace,laid on 20mm thick cement sand mortar in the ratio of 1:4 (1 cement:4coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1,including rubbing and polishing of the surface upto 3 cuts complete,including providing skirting upto 150mm height along the parapet walls in the same manner complete all as specified and directed.

M & L Plain Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate min radius of 75mm thick as in roof and parapet wall junction, roof benching, kerbs, mud stop, coping, rounded or chamfered on edges, incl necessary sloping on roof including form work complete all as specified.

Taking down door/window/ventilator frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified.

Taking down door/window/ventilator frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified..

S&F for powder coating (minimum thickness of powder coating 50 micron) anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S & F for powder coating(thickness of powder coating not less than 50 micron) Anodised aluminum door shutters, aluminium section weighing 0.55 Kg/ metre including necessary joining cleats, glazing clips, rubber nafron packing, handles 02 Nos in each doors, hinges, anodised aluminium snap bidding screws etc complete all as specified and directed.

S&F 4.0 mm thick sheet glass tinted quality and glazing with oil putty or with aluminium snap beading in square n.exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F 4.0 mm thick sheet glass tinted quality and glazing with oil putty or with aluminium snap beading in square exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F 4 lever aluminium mortice lock, vertical type size 100 mm complete all as specified.

S&F hydraulically regulated extruded aluminium body door closer designation No 3 universal type suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 Kg etc complete all as speciified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings in any position complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (coating of sheet not less than 150 GSM) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, slightly/completly rounded or chamford or curved and curved at front side as per site requirement fixed with self tapping screws complete all as specified and directed.

Demoltion of brick work built in cement mortar of any specification and in any position complete all as specified.

M&L 15mm thick rendering with ready mix mortar of approved make on wall surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10-12mm thick rendering with ready mix mortar of approved make on brick work or concrete surfaces on wall, finish the surface even and smooth without using extra cement complete all as specified and directed.

PMM repairs (FOR PATCH REPAIRS)

25-30 mm average thickness ( in 2 layers) up to 3.5mtr height

50-60 mm average thickness ( in 3 layers ) up to 3.5mtr height

PMM repairs at 59 and 60 above shall be done as per following methodology (From sub items (i) to (vi) below)

i) Chipping of plaster and unsound/weak concrete material till reinforcement bars are exposed, which enable their rust removal vides item ii) below, from slabs, beams, and columns etc. with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-incharge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris up for all lifts and leads .

ii) ) Rust removal by Providing and applying Fosroc Reebaklens RR or equivalnet from SIKA/ BASF, a combination of acid based material, corrosion inhibitors and dispersing agents rust remover, for removal of all rust/ scales/corrosion from reinforcement bars before microconcreting or patch repair,It Shall be applied with brush for complete wetting of rusted metal surface at coverage of 2- 2.5 Sqm/ltr. & allow it to react for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal /steel for about 5-7 days. Before applying any protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth.

iii) Anticorrosive treatment by Providing and applying Nitozinc Primer an epoxy based zinc rich anti corrosive primer having adhesive bond strength ≥ 1.5 MPa as per ASTM D4541, & shall comply to per ASTM B-117 to be applied on well cleaned, fully exposed and all loose scale , rust free surface obtained by grit blasting or suitable means , to be done with coverage @4.5sqm/litres to achieve a minimum thickness of 40microns DFT or as per direction of Engineer-In charge.

iv) Epoxy bonding for Old concrete & New concrete by providing and applying bond coat on the prepared surface with two component epoxy based bonding coat Nitobond EP of Fosroc make or equivalent, having specific gravity 1.15 to 1.2 gm/cc, Compressive strength(BS 6319 Pt.2)- 50 Mpa at 7 days, Flexural strength strength(BS 6319 Pt.3)- 35 Mpa at 7 days, Tensile strength (BS 6319 Pt.7)- 20 Mpa at 7 days, Shear Strength (BS 6319 Pt.4)- 10 Mpa at 7 days, having an over lay time of 6 hrs and 30 ̊C. Bonding agent shall have coverage not less than 2.5sqm/litres Laying of reinstatement polymer modified mortar or micro concrete shall be completed within the overlay time of bonding coat. Item rate is inclusive of materials all labour, tools and tackles. complete as per specification and as directed by Engg.-in-charge.

v) PMM by providing and laying single component, polymer modified, fibre reinforced cementitious repair mortar, Rendroc SP40 or equivalent from SIKA/BASF over the tacky bond coat, that achieves Compressive strength (BS 1881 Pt.116) > 20 MPa at 1 day , > 45 Mpa at 28 days, Tensile Strength > 2.5MPa, Flexural Strength > 7Mpa at 28 days, Finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slabs, piles etc., complete in all aspect as per manufactur's methodology. Rates include cost of all labour, materials, Tools and Plants,propping, scaffolding, shuettering, safety arrangment, quality control, testing complete as per specifications and direction of engineer in charge.

vi) Item rates of PMM 25 mm and PMM 50 mm (against items (a) and (b) respectively ) are inclusive of all materials, labour, tools and plants, propping, scaffolding, safety arrangement, quality control, testing and all items of works from i) to v) above quality control etc. complete in all respect, as per specifications and as directed by Engg.-in-charge.Work shall be complete only after proper wet curing has been done by contractor and surface has been evaluated for satisfactory quality by sounding/tapping with a blunt metal instrument, and testing of PMM cubes filled up and cured by contractor during the application of PMM (75mm size cube crushing strength at the end of 28-day to be not less than 45 N/sqmm) in addition to NDT Testing as per under item of "Testing of works"

PLASTERING on ceiling and outer walls and other structural elements upto 3.5m height level over PMM/shotcrete repairs or otherwise as replaster as per details given under sub items (a), (b) below;

M&L 10 mm thick cement plaster of in the ratio of 1 cement and 4 clean sand zone III added with Polymer SBR @2% of cement weight, on ceiling over PMM repairs, shotcrete repairs or as replaster of damaged plaster including preparation of surface by demarketing of PMM repaired surface in regular shape or removal of damaged plaster, direction of engineer in charge.

Rate quoted against this item vides sub item (69) above shall include all materials, labour, Tools and Plants, Scaffolding, safety arrangement and preparation of surface as mentioned vides (a) above complete in all respects as per specifications and direction of Engineer in charge

S&F Vitrified ceramic tiles 10mm thick (Square/rectangular)polished area of each tiles not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured (Light Shade)cement to match over 20 mm thick screed bed or bedding layer of cement mortar(1:6) for laying floor finishes complete all as specified.

M&L for light shade Vitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in Skirting set and jointed in cement slurry over and including 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L Glazed ceramic coloured joint free tiles of size 450mmx300mm,6 to 7mm thick on vertical surfaces of walls such as skirting dado etc and jointed in neat cement slurry and pointed in white cement to match laid over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over & including 15mm thick screed in cement mortar (1:4) with pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

Demolition of unreinforced cement concrete in ground floor and pavings n.exc. 15 cm thick (below or above GL) complete all as specified and directed by Engineer in Charge

M&L for 75mm tk Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floors finishes complete all as specified and directed

M&L 25mm thick sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L 80mm thick,M-40 Grade Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment complete all as specified and as directed.complete all as specified and directed.

M&L 60mm thick,M-40 Grade Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment including dismantling of old paver block or stone slab laid dry complete all as specified and as directed.complete all as specified and directed.

M&L Plain cement concrete 1:2:4 type B -1 all around the interlocking tiles to fix in position as in kerbs Complete all as specified and directed by Engr-in-charge

M&L 75mm thick PCC(1:3:6) type C2(using 20mm stone aggregate) as in floors/pavings/plinth protection etc,finished even and fair without using extra cement grooves filled with bitumen mastic filling of mix(1:2) (bitumen and sand) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes(any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories)

S&F 110mm bore PVC (SWR) pipe of pressure not less than 4 Kg/Sqcm in single socketed, in any length with rubber ring joints, fixed to wall including distance pieces and stack clamp with nuts & bolts complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe of pressure not less than 4 Kg/Sqcm in single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends any radius complete all as specified.

S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

Dismantling wrought iron/mild steel work in any position complete all as specified and directed

S&F Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) Quality 'A' including fabrication, erraction and fixing complete all as specified and directed by Engr-in-Charge.

M&L for washing rubbing down and stopping of cement based painted surfaces and applying one coat of cement based paint on wall surfaces including proper curing all as specified and directed.

Surface excavation in soft /loose soil not exceeding 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed by Engr-in-Charge.

Excavating in trenches n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts wells cespits, manholes, pier holes etc n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in layers including leveling watering and well ramming in layers n.exc 25 cm thick compelte all as specified and directed.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in foundation filling, sub base for floors etc complete all as specified and directed by Engr-in-Charge.

All as per Serl Item No 7 here in before but half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Use & waste of formwork to sides of concrete foundations, footings, bases or column,raft and raft beams,sides and soffits if any of foundations and plinth beams and similar work,vertical or batter for flat rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.

Use & waste of formwork to sides of pillars,posts,struts,piers,columns and stanchions etc fair finished for square/rectangular or polygonal surfaces of concrete complete all as specified and directed by Engr-in-Charge.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed.

M&L for RCC (nominal mix) in (1:2:4) type B1 20mm graded stone aggregate as in foundations including rafts,footings,foundations beams ,bases of column etc complete all as specified and directed by Engr-in-Charge.

M&L for RCC (nominal mix) (1:2:4) type B1 20mm graded stone aggregate as in columns, pillars,piers,posts and struts etc complete all as specified and directed.

M&L for RCC(nominal mix) (1:2:4) type B1 20mm graded stone aggregate as in slabs supported on walls,beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick cement plaster in cement mortar 1:6 on brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for hard core of broken stone or boulders gauge n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and ramed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L for 100 mm thick PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate ) as in sub base for floors etc complete all as specified and directed by Engr-in-Charge.

M&L for 50mm thick PCC(1:2:4) type B-1 (using 20mm graded stone aggregate) as in flooring complete all as specified and directed by Engr-in-Charge.

S&F Solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube supplying and fixing as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail either side & as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm butt hinges medium weight cold rolled fixed to doors with SS screws complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle,and steel peg stay,complete with glazing bars,dovetailed or welded complete all as specified and directed by Engr-in-Charge.

S&F steel window with side hung shutters including projecting type hinges with steel handle,and steel peg stay,complete without glazing bars,dovetailed or welded complete all as specified and directed by Engr-in-Charge.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified by Engr-in-Charge.

S&F Vitreous china white wash down water closet (pedestal pattern) including PVC seat cover and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc, fixed as in repair, complete all as specified.

S&F in repair 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphonic handle lever PVC bend including connecting to WC and fixing on walls with bracket all as specified.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S& F Bib tap of cast copper alloy brass but fancy type, Chromium plated 15mm bore, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F 1000 litres capacity rotational moulded, triple layer polyethylene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roof including fittings complete all as specified and directed by Engineer in Charge.

S&F Gun-metal, globe or gate valves 20mm dia bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 gms) and fixed complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore stop/angle valve cast copper alloy with crutch or butterflty handle, screwed down screwed high pressure for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup complete all as specified and directed by Engr-in-Charge.

S&F PVC Connection pipe, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified.

S&F 600 mm long towel rail of PTMT fixed to wall with steel screws and PVC rawl plug complete all as specified and directed.

S&F Health Faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed by Engr-in-Charge.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and directed by Engr-in-Charge.

S&F Vitreous China bowl urinal flat back, size of 465x355x265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, and flush pipe ) including waste pipe 32mm dia bore complete all as specified and directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F 75mm bore PVC(SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 75mm bore PVC(SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) 'S' trap complete all as specified and as directed.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge.

M&L for cement concrete 1:3:6 type C2 with using 40 mm graded stone aggregate as in concrete bed to drain pipe 150 mm dia including packing under and haunching against the sides of pipe after they are laid and tested completed all as specified and directed by Engr-in-Charge.

S & F salt glazed stonewire drain pipe 150 mm internal diameter grade A laid in trenches jointed and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains 150mm dia,making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished & reforming benching as required complete all as specified and directed by Engr-in-Charge.

M&L for applying two coats of synthetic enamel paint (ordinary tint) over one coat of primer on new plastered surfaces including preparation of surfaces complete all as specified and directed.

Excavation in post holes n.exc 0.5 cum each getting out,returning filling in and ramming earth in layers n.exc 25cm watering and removing surplus soil to a distance n.exc 50m and making good surface in soft/loose soil complete all as specified and directed.

M & L for cement concrete 1:2:4 type B2 (40mm graded crushed aggregate) in Cement concrete in foundations, filling and mass concrete and posts (including caps and bases) complete all as specified and directed.

M&L for Rolled mild steel Fe 410 Gde E 250 Quality A in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated

M&L for two coat of black bituminous painton Surfaces of any description wood, steel iron, concrete, brick, stone, etc. n exc 10cm in width or girth

Taking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets,regulators light fittings) and removal from site and making good the disturbed surfaces of (wall/floors/ceiling etc) complete all as specfied & directed.

M&L for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in box of 1.6 mm thick including one coat of synthetic enmelled black paint and providing with brass screws and cup washers including single core multi stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit all as specified and directed by Engr-in-charge for the following :-

(a) One light/fan/bell point controlled by one way switch 5 amps.

(b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board.

All as per item No 142 above but with single core copper conductor cable FLRS 2.50 sqmm for one power switch socket 16 Amps concealed and including provision of 2.50 Sqmm PVC insulated single core copper conductor cable as earth continuity conductor on independent board.

M&L for One power point with PVC insulated stranded copper conductor cable 4.00 Sqmm single core 1100 Volts for one 3 pin AC Box outlet, 20 Amps concealed and including provision of 4.0 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board. (For AC Point)

S&F of switch piano flush type type 6 amps single pole one way complete all as specified and directed.

S&F of switch piano flush type 16 amps single pole one way complete all as specified and directed.

S&F of socket outlet multipurpose 2 in 1, 3 pin 6 amps flush button type complete all as specified and directed.

S&F of socket outlet multipurpose 2 in 1, 3 pin 6 and 16 Amps complete all as specified and directed.

S&F of switch modular type 6 amps single module one way 230 volts, 50 Hz complete all as specified and directed.

S&F of switch modular type 16 amps single module one way 230 volts, 50 Hz complete all as specified and directed.

S&F of socket modular type 6/16 amps 2/3 pin combined two module one way 230 volts, 50 Hz complete all as specified and directed.

S&F of ceiling fan regulator flush type on step type for 1200/1400 mm sweep ceiling fan including connections complete all as specified and directed.

Supply, laying and drawing submain wiring in and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the disturbed surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including taking down existing old wire all as specified and directed. Note :- Two runs of IC x 6.00 sqmm (Phase wire and neutral ) and one run of IC x 6.00 sqmm (as earth wire) will be measured as one unit length.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades and deposit to MES store to refixing with complete accessories all as specified and directed.

S&F of factory made epoxy polyester powder coated distribution board SP & N 4 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of factory made epoxy polyester powder coated distribution board SP & N 12 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 10 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-54 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for 100 Amps 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 including taking down old DBs all as specified. NOTE :- (a) MCBs/MCCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of MCCB 100 Amp 4 pole 16 KA at 415 V complete all as specified directed.

S&F of single pole MCB 6 to 32 Amps, 240 V, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F of SPN MCB 32 amp, 240 V, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

S&F in repair surface mounting LED aluminium Batten 10W LED light 2 Ft Fixture should have minimum efficacy at system level >=100 lumens/Watt, CCT 4000-6500K & PF≥0.90 complete all as specified and directed.

S&F in repair surface mounting LED aluminium Batten 20W LED light. Fixture should have minimum efficacy at system level >=120 lumens/Watt, life of fixture not less than 50K Hrs,CCT 4000-6500K & CRI>80, PF≥0.90. An operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed. Similar to Eveready: LEDBTA02016-02,Havells: LUMILINEPLUSPROBS20WLED865SPCSSIND,Philips: BN170CLED20S6500PSUL120

S&F of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED light fitting 1x 9/1x10 watt bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable complete all as specified and directed.

S&F of 35 watts 230 V AC outdoor type with High efficient LED Building security light fitting with high pressure die cast Aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP: 65/66 protected complete with bracket made out of 32 mm GI pipe light grade 1.2 mtr long bend to shape with clamps and fixing bolts all as specified and directed.

S&F round shape 6 watt 220 volts AC recessed type with high efficiency glare free light complete with drivers,holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F exhaust fan, steel body AC single phase. 230 V of size 300mm sweep with blades and frame and louvers complete all as specified and directed including taking down old exhaust fan and deposit MES store yard.

S&F Fresh Air fan,250mm sweep with louver shutter 1200 RPM single phase. 230 V including cutting hole in the wall for fixing of fan complete all as specified and directed.

S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

S&F in repair modular AC Box with 20A SP mini MCB, Plastic enclosure & unbreakable Heavy Duty ISI mark Plug Top complete set duly concealed in wall complete all as specified and as directed.

S&F in repair 1100 volts grade heavy duty cable with PVC insulated aluminim stranded conductor served with an inner seathing of PVC armoured , PVC sheated 6sqmm nominal cross section 2 core complete all as specified and as directed.

S&F of single pole MCB 40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

M&L far Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

The new hut furnitures (BID ID -3400333)

Kunal Construction Co. (BID ID -3398997)

M/s M M BAHL (BID ID -3399522)

UNIQUE BUILDERS (BID ID -3397259)