Special Repair in HARTRON Centre Electronic City Sector 18 Gurugram in Gurugram District

Amount

(A) CIVIL WORK Dismantling brick work, Tile Masonary or Tile liing and Tile terracing b) in cement (HSR:8.5b)

Dismantling reinforced cement concrete with cleaning and straightening and cutting of bars if required (HSR:8.6e)

Removing door and window (Wood and steel with chowkats by making recesses in walls when the wall is not to be dismantlled:- (HSR:8.17) a) Doors

Cement Concrete 1:8:16 with stone aggregate 40mm nominal size in foundation and plinth. (HSR:10.28)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects. (10.82 + 10.95a)

Providing & laying 80mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 over a bed on 30mm thick fine sand complete in all respect. (HSR 10.159)

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level.(HSR 11.7)

Corrugated G.I. sheet roofing 0.80 mm thick fixed with galvanised iron ‘J’ or ‘L’ hooks, 10 mm dia G.I. limpet and bitumen washers complete, excluding the cost of purlins, rafters and trusses. (HSR:13.18)

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR:13.64)

Providing and fixing PVC rain water pipe 6 Kg pressure of ISI mark in cement mortar during masonary work. (HSR 13.89) a) 100mm dia PVC pipe 6 Kg . Pressure. Make supreme, finolex, prince

b) 150mm dia PVC pipe 6 Kg . Pressure. Make supreme, finolex, prince

Providing and fixing PVC Bend ISI mark (HSR 13.90b) a) 100mm dia PVC Bend Make supreme, finolex, prince

b) 150mm dia PVC Bend Make supreme, finolex, prince

Providing & fixing Ceramic Tiles/ anti skid tiles of size 400 x 400mm or abovee size of approved make in floors, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like RAK, NITCO, KAJARIA, SOMANI, ORIENT & JONHONSONS. (HSR 14.91) (Tiles will be supplied by the department)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. Digital Print tiles of Size of 300 x 450 mm of reputed manufacturer shall be used as approved by the Engineer-in-charge like : - RAK, NITCO, KAJARIA, SOMANI, ORIENT & HOHNSONS [HSR 14.92(b)].

12mm cement plaster 1:6 on walls (HSR 15.7)

15mm cement plaster 1:6 on the rough side of single or half wall (HSR 15.12)

12 mm thick cement plaster 1:2 on terrace floor complete in all respect (HSR:15.48)

10mm thick cement plaster 1:4 under side of ceiling (HSR 15.52)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1)

Applying priming coat with metal primer on new steel or iron work including preparation of surface. (HSR 16.9)

Painting two coats excluding priming coat with ready-mixed paint for metallic surfaces in all shades on new steel or iron work. (HSR 16.17)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58)

Finishing walls with exterior decorative cement paint based paints, such as snowcem Robbiacem ets. On old work, one coat give even shade. (HSR:16.62)

Providing & applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./ Birla make). (HSR 16.81)

Providing & fixing aluminium fittings complete for doors and windows, such as tower bolts,handles,etc. and screws for these fittings (excluding sliding bolt) (HSR 17.72 (a)) (a) for single leaf shutter

Providing and fixing, 150 mm hasps and staples with necessary screws, etc., complete (HSR 17.78 (b) b) Aluminium

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) Duro, Green make 35mm. thick (HSR 17.93a iii- note I under 17.18))

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors open able or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR:18.12)

Fe-500 EQR TMT steel bars for RCC works, where not including in the complete rate of RCC including bending, binding and placing in position complete. (NS). Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: -(HSR 18.34) a) Door & window frame of size 89X50mm with 40mm wide single rebate

Dismantling of road including soling and wearing coat, screening and stacking of old serviceable material, complete in all respect. (HSR:24.37)

ii) DSR ITEMS Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). (DSR:16.69)

Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.(DSR:16.82)

Laying at or near ground level old kerb stones of all types in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints, except at sharp curve, shall not be more than 5 mm), including making drainage opening wherever required etc. complete as per direction of Engineer-in-charge. (Length of finished kerb edging shall be measured for payment). (Old kerb stones shall be supplied by the department free of cost) (DSR:16.85)

B) PH WORK Providing and fixing in position best quality stainless steel sink with complete fittings. HSR:30.53

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR 30.75)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin- charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. (HSR 30.41) iv Size 630mm x 450mm with one No. tap

CONSTRUCTION BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 BENCHING 12mm THICK CEMENT PLASTER 1:2 with a floating coat of 1mm thick of neat cement R.C.C.1:2:4 SLAB 100mm THICK /C.C.TOPPING 50 mm THICK WITH 455 MMx455MM/455MMx610MM INSIDE LIGHT DUTY C.I.INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design (HSR 29.84)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- VITREOUS CHINA WARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (HSR: 30.5) i) White

EXTRA FOR providing and fixing 32 MM dia. G.I./C.P.FLUSH PIPE complete with accessories instead of 32/MM dia. galvanised telescopic flush pipe with clips (as required by the Engineer-in-charge). (HSR:30.15 32 mm dia. C.P. brass flush pipe (URINAL + WASH BASIN)

PROVIDING AND FIXING POSITION BEST INDIAN MAKE FLAT BACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH CONSISTING OF : - (i) Flat back lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval of the Engineer-in-charge). (ii) 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I.AUTOMATIC FLUSHING CISTERN, PAINTED WITH non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15 mm pipe; (iii) PAIR OF R.S.PR C,I. PAINTED BRACKETS AND BRASS COUPLINGS; (iv) Standard size G.I.FLUSH PIPE WITH C.P.BRASS WALL CLIPS AND UNIONS COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in-charge). (HSR:30.19 IV) STANDERED SIZE GI FLUSH PIPE WITH CP BRASS VALVE PEETS AND UNION COMPLETE. i) White

Providing and fixing in position best Indian make C.P. brass basin mixer complete instead of one no pillar tap(HSR 30.46)(a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET. (HSR:30.66) c)C.P. brass with revoiving joint

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with raw slugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC.(HSR:30.68) (b) 20 MM DIA C.P.BRASS ADJUSTABLE 600MM

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC (HSR:30.71) (a) INDIAN MAKE (i) 600mm X 450mm

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineerin-charge) (HSR:30.76)(a) 15 MM STOP COCK (ii) Concealed stop cock with flange

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P. BRASS WALL MIXER 15 MM (HSR:30.81) (b) Without Telephonic shower

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION.(HSR:30.82) (b) C.P. Brass (i) 15 mm X 300 mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P.BRASS INLET CONNECTION 15 MM WITH 375 MM PIPE AND C.P. BRASS NUTS (HSR 30.83)

PROVIDING AND FIXINGIN POSITION M.S.OR HEAVY FLAT IRON CLAMPS made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. SOIL WASTE vent or anti pipes to walls COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS ETC., AND PAINTING.(HSR 30.88) for 100mm i/d Pipes

PROVIDING AND FIXINGIN POSITION H.C.I. FLOOR TRAPS I.S.I.MARKED OF THE SELF CLEANING DESIGN WITH C.P. BRASS HIGED GRATING WITH FRAME WITH OR WITHOUT VENT ARM AND INCLUDING CEMENT CONCRETE 1:2:4 under and around the floor trap where required upto floor level COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS, ETC., minimum depth of water should be 150 mm with a minimum seal of 50 mm (HSR:30.89) b) with 75 i/d outlet

CUTTING CHASE IN BRICK WALLS IN CEMENT OR IN FLOOR FOR EMBEDDING G.I.OR H.C.I.PIPE LINES AND MAKING GOOD THE SAME TO ITS ORIGINAL CONDITION. (HSR 30.95) a) Size 75mm x 75mm

PAINTING G.I.PIPES AND SPECIALS WITH 1ST AND 2ND QUALITY SYNTHETIC ENAMEL PAINT IN ALL SHADES ON EXISTING OR NEW WORK, TWO COATS PAINTS INCLUSING CLEANING, RUBBING SURFACE, ETC. (HSR 30.106) b) 25mm i/d of pipes and specials

Providing and fixing in position automatic brass ball valve in tanks (HSR 30.110)

PROVIDING AND FIXINGIN POSITION GULLY TRAPS FIXED IN CEMENT CONCRETE 1:4:8 complete WITH H.C.I.GRATING 150 MM X 150 MM CAST IRON COVER WEIGHING APPROXIMATELY 7.26 K.G. AND FRAME CLEAR OPENING 300 MM x 300 MM and outside size 330 MM x 330 MM AND CHAMEBR INCLUDING cost of all brick work in CEMENT MORTAR 1:5 CEMENT CONCRETE 1:8:16 IN FOUNDATIONS, AND CEMENT CONCRETE 1:2:4 IN COPING around C.I. cover and frame etc. WITH THREE COATS of black bitumastic superior PAINT of approved manufacture on all C.I. work AS PER STANDARD DESIGN, minimum depth of water should be 150mm with a minimum seal 50mm. HSR:30.114) 100 mm internal diameter S.W. gully trap

Providing and Fixing HDPE Water storge tank of sintex, Diplast, O.K. supreme make with covers/lids marked with IS: 12701 on roof top of building including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge.(Except civil work). (HSR:30.119) 5000 litres capacity

Providing and fixing 5 liter capacity cistern with ISI make.complete in all respects to the entire satisfaction of Engineer-in-charge (NS)

DSR Items Providing and fixing GI pipes with GI fittings and clamps, i/ cutting and making good the walls etc (DSR 18.10 ) (i) 15mm dia internal diameter pipeline

(ii) 20mm dia internal diameter pipeline

(iii) 25mm dia internal diameter pipeline

Providing and fixing GI Unioin in GI pipes including cutting and threading the pepe and making long screws etc. complete (DSR 18.46) (b) 20mm nominal bore

c) 25m nominal bore

Providing and fixing Gun Metal Gate Vlave with CI wheel approved quality (screwed end) screws etc. complete (DSR 18.17 (b) 20mm nominal bore

c) 25m nominal bore

RECOVERY ITEMS The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. The steel bars obtained on dismantling of existing boundary wall have been calculated taking assumption that theoretical steel bars will be retrieved. The steel bars will be issued for use in any of the item for the work after modification (bringing it to required specifications) as per approval of employer. In case it is not possible to use these steel bars on the work, the agency can take away these steel bars after approval from employer; These steel bars will be issued at the price quoted by the agency. However the reserve price is as under:- Bricks @ Rs.2.40/- Each

Brick Bats @ 450/- per cum

Steel Bars @ 20/- per KG

Doors of Wood @ 100/- Each

D K Contractor