REPAIR/ MAINT TO CERTAIN ROAD INCLUDING ROAD FURNITURE IN GRC AREA-I UNDER GE KAMPTEE.

Amount

Repairs to pot holes any depth, not exceeding 1 sqm each including sweeping free from dust with mechanical equipment and mud or water, scoring sunken surfaces in roads, paths etc by using pressure air ,cutting around edges to at least 25mm in depth, making good by applying tack coat at 5 Kg per 10 Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 Kg per 10 Sqm blinded with 0.09 Cum of stone chippings 6.3mm size and again well rammed (including supply of premixed bituminous macadam, binder and chippings), depth of pot holes exc 30mm complete all as specified and as directed.

Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with mechanical equipments and clean the surface by using pressure air to remove all loose dirt etc., complete all as specified and as directed.

Material & Labour for applying evenly a priming/tack coat with bituminous primer using paving bitumen @ 5 kg per 10 Sqm on black top surface using mechanical sprayer complete all as specified and as directed

Material & Labour for premixed asphaltic semi dense concrete 30 mm consolidated thickness with 5.5% binder content (paving bitumen of grade VG-30) by weight of total mix, rolled and compacted to required camber and gradient using 8 to 10 tonne power roller complete all as specified and as directed. Note: The work should be executed by using hot mix plant and mechanical paver.

Material & Labour for premix bituminous macadam (consolidated thickness 75mm or less) with 4% binder content by weight of total mix (paving bitumen of grade VG-30), mixed in hot mixed plant and laid by using mechanical paver and rolled & compacted to required gradient and camber using 8 to 12 tonne power roller complete all as specified and as directed.

Material & Labour for preparation of road surface and applying thermoplastic reflective paint in marking of minimum 2.5 mm thick single coat as in center line and edge line road marking of 150/100 mm width using 'HOT MARK' thermolastic modern propelled road marking machine as directed including all ingredients such as binder, glass beads Titanium dioxide calcium carbonate inter fillers thermoplastic requirement for glass beads shall be the table No. 800.4 of MOT specification including spraying of glass beads etc., all as per manufacture instructions and as directed by Engineer-in-Charge.

Surface dressing not exceeding 15cm deep averaging up to 100 mm and getting out in soft/loose soil for road side berms to required gradient complete all as specified and as directed.

Removing excavated material/soil to a distance not exceeding 50m depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed by Engineer-in-Charge.

Material & Labour for approved moorum/red bajari, in road berms, spread thickness 100 mm, rolled and consolidated to gradient and camber required with light roller of capacity not less than 0.50 tonne complete all as specified and as directed.

S&F aluminium road studs of size 100mmx100mmx20mm with shank reflective, mocro prismatic (red/yellow/white) with MS zink coated nails of size 12 mm dia and 120 mm long having both as sides (Dual direction ) high impact ABS 3 Nos containing 7 heads each i.e 42 heads in retro reflector etc., complete aluminium coated of approved quality, as per manufacturer's instructions, complete all as specified and directed.

S&F regular delineators made out of MS pipe of 75mm dia with powder coating, 120cm long with 3 nos 100mm wide prismatic /commercial AVERY DENISON USA/3M grade reflective sheeting colour coding as approved & provided with reinforced mesh, as per manufacturer's instructions. complete with necessary earth work and PCC 1:2:4 type B1 (using 20mm graded stone aggregate) for fixing the delinator,complete all as specified and directed.

Supply and fixing of 900 mm dia convex mirror made of PC material provided with suitable MS pipe post, duty powder coated for road turning, intersections, curves T junctions, parking lots etc and also held ideal for surveillance. It should have clear and definite mirror image having 130 degree of viewing angle. It is unbreakable & stronger than glass. Note: Rate for fixing of mirror with PCC 1:2:4 type B-2 filling of size 45 x 45 x 50 cm shall be deemed included in the rate quoted.

S&F solar road studs pf size 125mm x 125mm x 20mm aluminium alloy & polycarbonate stud (Red/yellow LEDs) 3+3 LED's with shank in tough aluminium diecast body with stem as in repairs, complete as per MORTH/IRC specifications and manufacturer’s instructions, complete all as specified and directed.

Parasram Mulchandani

M/s Rahul Traders

vidhamal&sons

J.P ENTERPRISES

H.M Traders

Meet Road Lines

Bidder Name

J.P ENTERPRISES

Meet Road Lines

M/s Rahul Traders

H.M Traders

vidhamal&sons

VIJ ASSOCIATES

Parasram Mulchandani