Providing and Supplying Modular Furniture for Newly Constructed Government School Building at Kachigam, Nani Daman.

Providing Supply and installation of CORNER SINK TABLE -Size :-1100mm L x 1100mm D x 900mm H construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation. Dimensions : W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994) •Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pre Treatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle : Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit)•Hinge: SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profill. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. PP Sink,Polypropylene Molded Sinks: Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Sink - Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet - 3-way type faucet as per approved make WorkTop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of CORNER TABLE - Size 1100mm L x 1100mm D x 900mm H construction: Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge , Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency having NABL accreditation. Dimensions: W= 900 mm, D = 900 mm, H = 875 mm Configurations: 1 Shutter - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk. Finish: Powder coating pure epoxy, thickness 40-50 microns , followed with 9 tank Pre Treatment process The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge : SS Hinge Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. Work Top : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of ISLAND TABLE - Size :-4880 mm L x1540mm D x 900mm H with Electrical trunking Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 8 Nos , Leg space - 6 Nos , Corner leg space - 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness : LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of ISLAND TABLE Size :-4880mm L x1540mm D x 900mm H with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 8 Nos , Leg space - 6 Nos , Corner leg space - 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The

Providing supply and installation of ISLAND TABLE Size :-6080mm L x1540mm D x 900mm H with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 10 Nos , Leg space - 8 Nos , Corner leg space - 2 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of WALL TABLE - Size :-1280mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 1 Nos , Corner leg space - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of WALL TABLE - Size :-2780mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 2 Nos ,leg space - 1, Corner leg space - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of WALL TABLE - Size :-3640mm L x750mm D x 900mm H with Electrical trunking Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 3 Nos , Leg space - 2 Nos , Corner leg space - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority)

Providing supply and installation of WALL TABLE - Size :-3640mm L x750mm D x 900mm H with Electrical trunking with 2 tier fixed type reagent rack having integrated electrical switch sockets Construction : Floor based Welded cabinet system having storage body should be flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. It should be relocated anywhere easily as it is an independent unit. Cabinet should of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Toe-space of 90mm X 90mm is provided at front-bottom side of cabinet. Levelers are provided for easy leveling of welded cabinet. Shelf should be eight-bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable and hinges should be easily replaceable. Knee space panel should be in 22 gauge construction. Cabinets are tested as per SEFA 8M standard from a SEFA approved Lab and also tested as per EN 14727 from a third party testing agency Dimensions: W=600 mm, D = 530mm, H = 875 mm Configurations: Storage - 600 W 1 Drawer + 2 Shutter - 3 Nos , Leg space - 2 Nos , Corner leg space - 1 Nos MOC: MSCRCA: IS – 513 (1994) Thickness: LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel is of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel is of 0.8mmthk Finish: The complete M.S. material of cabinet should be pre-treated (degrease, Zinc phosphates) and epoxy powder coated for better corrosion resistance. The thickness of powder coat should be 45-50 microns, which passes the test of Salt Spray for 1000 hours. It should have a high temperature withstanding capacity with excellent electrical insulation properties.The rear portion of above accessories which is in contact with live metal should be made from thermo set material which will not melt on heating. Handle: Anodized Aluminum Recessed-Type, CTC: 160.0mm Lock: Units have a locking facility with 180° and 10 lever cam lock mechanism (except for sink and corner unit) Hinge: SS Hinge .Screw: SS 304.Shutter : should be of twin-type construction with sound dampening effect using profile. Shutter cover should be equipped with Bump on for sound dampening. Base Moulding should be made of PVC with corner clips. Ball Slide: 500mm Length Shutter should have provision of roller catch. COVER / FILLER PANELS All side cover panels and back panels, filler panels should be made from CRCA MS panels of 1.0mm thickness with pure epoxy powder coating . SERVICE FITTINGS AND ACCESSORIES Service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Service Indexes: Fittings should be identified with service indexes in the color coding as per DIN 12920. Fixed-Type reagent shelves :It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. ELECTRICAL ACCESSORIES (6/16 A SWITCHES & SOCKETS) : These are made of High gloss virgin grade engineering thermoplastics to impart a defect free surface. they impart excellent electrical insulation properties i.e. do not melt on heating or catches fire. Owing to this all electrical switches and sockets are capable of handling higher currents and operating temperatures. Front plates can be changed at any time with ease without disturbing the wiring to quickly and economically match changes in the surroundings. Worktop : Jet Black Granite: It should be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfer and smoothed. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.(Make as Per Selection of Architect Or Selection Of Higher Authority)