WBPWD/SEWEC /BRED /NIQ-44/2019-20

Amount

SUB-HEAD 1-FIXING OF LIGHT FITTINGS Fixing only single/twin LED tube light fitting complete with all accessories directly on wall/ceiling by screws etc.

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with sutable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length with canopy. [17/ C-2 ]

Extra for suspension exceeding 25 cm with S&F additional 2 no. 20 mm dia EI conduit (14 SWG) supports & necy. PVC insulated wire and painting etc. as required by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length. [16/ C-2 ]

Fixing only lamp [11/ C-2 ]

SUB-HEAD 2- SUPPLY OF LIGHT FITTINGS Supply of 4ft LED T-8 box type single batten with end cap complete with all accessories [ PHILIPS make cat no TMC501P1xT LED22WP3241/Crompton/Bajaj/Wipro)

Supply of Twin 4ft LED T-8 box type batten complete with all accessories [PHILIPS make cat no TMC501P 2xT LED22WP3242/Crompton/Bajaj/Wipro)

S&F 18W LED T-8 lamp [ PHILIPS make cat no MAS LEDtube 1200mm18W865 /Crompton/Bajaj/Wipro) ] on fittings.

Supply & Fixing 15W Recessed mounted LED flat panel [Philips make DN296B LED 15S-6500 PSU /Crompton/Bajaj/Wipro)] with all accessories directly on ceiling.

Supply & Fixing 6W Recessed mounted LED flat panel [Philips make DN295B LED 6S-3000 PSU /Crompton/Bajaj/Wipro)] with all accessories directly on ceiling.

Supply & Fixing 36W Recessed mount 2'x2' LED flat panel [PHILIPS make RC 380B LED30S 6500G4 L60 W60 PSU OD OC/Crompton/Bajaj/Wipro] with all accessories directly on ceiling.

Supply 12W LED lamp to the lamp point. [Make: PHILIPS /Crompton/Bajaj/Wipro)]

Supply & Fixing LED Strip Light 5 Mtr Length with 24 Watt driver 3000K [PHILIPS make Sky cove 5 M WW /crompton /Bajaj/Wipro] with all accessories directly on ceiling.

S&F 170 LED out door Flood Lighting. [Make:- Crompton -LSFO-170-CDL/60 /Phillips BVP410LED170CW / Bajaj/Wipro)As per Coice of EIC ]

SUB-HEAD 3 -- FIXING OF FANS Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991) [29/D-14]

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc as per GS [ 21 (a) / C-3 ]

Engraving the deptt. number with 10 mm lettering on the body of fan upto 10 letters incl. hifen, stroke or stop [ 24 (a) / C-3 ]

Extra for additional one letter incl. hifen, stroke and stop as per GS

Painting upto 10 letters of the engraved number with approved black /red paint as required as per GS [ 26 (a) / C-3 ]

Extra painting for additional one letter of the engraved number as per GS [ 26 (b) / C-3 ]

Fixing only exhaust fan after making holes in wall as per GS

Supply & Fixing louver shutter ( Aluminum)on wall with necy. bolts & nuts (6 mm dia x 62 mm long) as per GS

SUB-HEAD 4 -- SUPPLY OF FANS Supply of ceiling fans complete with all accessories having the following Model / Cat No. ( Make -USHA striker/Crompton/Oroient )

1400 mm Sweep with safty wire & P2 capacitor ( Strick ) [ NS ]

Supply of Exhaust fans complete with all accessories having the following Model / Cat No. ( Make -EPC/USHA Turbo heavy Duty )

9" ( 230mm ) Speed 1370 RPM [ NS ]

12" ( 300mm ) Speed 1370 RPM [ NS ]

Supply & Fixing 450 mm sweep wall mounting fan and make necessary connection as required of Wall fans complete with all accessories having the following All Metal Body. Model / Cat No. ( Make -USHA/Orient Tornodo/ Crompton ) As per choice of EIC

Supply & Fixing 400 mm sweep wall mounting fan and make necessary connection as required of Wall fans complete with all accessories having the following All Metal Body. Model / Cat No. ( Make -USHA/Orient /Crompton or As per choice of EIC )

SUB-HEAD 5 -- AC machines SITC of 2T wall mounted type room Air Conditiner (cooling only) having the following specification & features.: a) Cooling capacity nominal (BTU /HR): 26000; Cooling Cap(min) Guaranteed (BTU/HR):25248 b) Star Rating -3/5 star c) Rated Voltage-230 V + / -5%, Frequency -50 Hz d) Compressor type- Rotary e) Mini. Room Discharge Air Flow Rate-1350CMH f) Refrigrant: R- 410A g) Cordless Remote Arrangement with all modernized provision of temperature setting , Fan speed option ( Low. Medium /High ) Auto Swing (Make :- MITSUBISHI HEAVY, model: Indoor SRK24CS-S6/A, Out door SRK24CS-S6/A)/O General/ Mitsubishi Electric As per direction of EIC With 15A plug top, 2mt long input cord , & all other installation kit except indoor to out door unit connecting pipes & cables, out door unit will be fixed on wall with heavy type wall base.Incl supply of wall base./on floor with necessary iron chair (300mm hight). fixed on roof floor.

S&F 15.88mm&6.35mm copper pipe with keno foam insulation & 6core 2.5Sqmm copper un aurmored cable. [ for connection of indoor unit to out door unit]

S&F 15mm PVC flexible drain pipe.

S&F timer DB for intermittent operation of AC machines. Consisting of following accessories. i) ( L&T, LTSD08N/Siemens/ABB) 8 way SPN DB ii) 240V, 32A DP MCB ( L&T/Siemens/ABB ) iii) 22A TP Power Contactor with 220V coil voltage, ( L&T, Cat No. MNX22-2P, CS90238 )/Siemens/ABB iv) Digital Time Switch ( L&T, Cat No. Crono 67DDT0 )Siemens/ABB v) Wiring with 4 sq mm FR PVC insulated wire, including connector, indicating lamp, and panel locking arrangement with labour

SUB HEAD-6 compound light S&F 300mmX300mmX100mm sheet metal (2mm thick) box with hinge type glass window door & locking arrangement fixed on wall. Consisting of DIN Rail, 1nos 2A sliding fuse & 1 nos 12 way 10A bakelite connector & necessary connection by suitable size copper wire. The box will be painted as per GS.

S&F digital time switch on din rail on existing box incl. necessary connection. L&T make crono time switch [cat no 67DDT0/Siemens/ABB

S&F25A 3pole power contactor on din rail on existing box incl. necessary connection. L&T make MNX 25-2P [cat no CS 90240/Siemens/ABB

Supplying and fixing 240V 10A SP MCB of Breaking capacity 10kA & C characteristics on din rail of existing box and necessary connection Make : L&T Siemens/ABB

S/F 80mm dia 1.5Mt long mini GI pole [TATA-M] including painting and S/F 1no GI flange as base plate including necessary holes as required including providing cement concrete(6:2:1) muffing around pole of dimension 2’-6 X2’-6”X2’-0” above roof level with cement mortar plastering and neat cement finish. Including S/F 8”X6”X4” GI loop box with 4pole Bakelite stud &40mm dia alkathane pipe for cable entry and 1.5Mt long arm bracket incl. painting as per GS.

Wiring with 2X 1.5 Sqmm PVC copper wire in 13mm dia polythene pipe from loop box to HPSV fitting. (average run 4mt)

Supply of 3core 10 Sqmm PVC insulated & sheathed aurmored cable (Make : Polycab/KEI/Havells)

Laying of 3core 10sqmm cable after cutting floor/pavement/wall as per GS for the following Sizes. 5(i)/F-3

Laying of cable following size of cable in underground trench as per GS for the following numbers of Cables. up to 35 sqmm [ 1(a)/ F- 2 ]

S&F 150W LED out door luminaire on arm bracket. [ PHILIPS make BRP 322 LED 142 CWMR FG54 XTFCL/Crompton/Bajaj/Wipro)

Supplying & Erection of 9 mtr long (410 SP - 32) Single Steel tubular pole of size Bottom- 5mtr, Middle-2mtr, Top 2 mtr, Outside Dia & Thickness of Section of Bottom- 165.1x4.85 mm , Middle- 139.7x4.50mm & Top- 114.3x3.65 mm with/without sole plate & Cap, with singale header assembly etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly.[NS] incl. S & F 25cmx25cmx10cm GI Loop box, 16SWG & incl. drilled hole in pole with providing muffing dimension 0.60 x 0.60 x 0.76 mt above ground level as per GS and S & F 1.5 mt 40 mm dia single arm bracket for fixing of light fitting as per direction of EIC

Painting of Steel Tubular Pole of lengths and no. of coats of paint, as given below with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint. Upto 9.0 mtr. long pole as follows- [ 4(a)/H-2 ]

1st coat of aluminium paint over 1 coat of RO priming

2nd coat of aluminium paint over 1st coat

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI-Medium GI pipe [ 2(b)/G-1 ]

Supplying and fixing compression type gland and finishing those for 2core 10SqmmXLPE / PVC armoured cable (2/4 / 3.5)Core as per GS. [7(a)/F4 & 8(b) /F5]

Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required.[40 mm dia] [F-6/11.E]

Sub head- 8 LED Sign Board. Supply, installation, testing and commissioning of LED illuminated 18’ x 4’ x 3” size sign board made of 1” x1” Iron hollow square bar with sufficient support bar in between the structure and fitted in wall with L channel and angle iron at the front side of the building. Thickness of the board in four side including 3’’ back side of the board should be covered with same ACP sheet and back portion of the board should be covered with 20 swg aluminum sheet to resist unwanted water seepage. 3 mm ACP of blue colour in the front of the structure and milky white 2.0” projected laser cut male and female acrylic letter will be fixed at the top of the ACP sheet with dark colour of acrylic sheet in side of male part to resist unwanted illumination from side of the letter. Female letter will consist of 1.5 watt sufficient Nos of water resist outdoor type LED module (make Bajaj / GE/Samsong) including supply and fixing controller in MS box outside of the structure.LED should cool milky white in colour, minimum 10000 burning hours, should have similar intensity at every point on the board, and should operate satisfactory up to 50 degree centigrade. Acrylic letter will be fixed on ACP base with such space so that all letters may read clearly from sufficient distance the four edges of the Boards should be fixed 40mmx40mm angle sheet channel with necessary steel screw .The cost including carrying (from companies work shop to Jangipur) and scaffolding charges(for 4 storied building) and painting with 2 coat of RO primer and one coat of synthetic enamel paint. The letter of following inscription below as per direction of EIC:- Tentative matter & final matter willbe approved by authority.

Supplying, fabrication & installation of 12"x12" Hollow MS bar structure by welding 4 nos 50x50x5 mm thick angle iron pillar(2 nos) for resting 16ftx4ft Glow Sign Board to a height of 6 .5mtr clearence between dround level to bottom of sign board, consisting of 1"x1" hollow bar interconnecting each other of 4 Nos. angle iron to the requisite height to be install on 14"x14"x10mm base plate heighted by 4ft 25mm dia. foundation build up to 4ft from ground level and cement concreting at a proportion of 0.6x0.6x.45m each made by CC(4:2:1) including plasting and net cement finish asso mending good the damages and top of the pillar welded by 12"x12"x10mm base plate to rest the sign board at a gape of 4mtr of 2 pillar.(390kg iron for 2 nos pillar)

Supply , delivery at site on foundation , commissioning of 62.5 -KVA, 415V, 50Hz, 3Ø silent new DG Set, comprising of Engine, alternator, separate AMF panel, Base frame, Fuel tank, Battery, CPCB-II approved Engin & Acoustic Enclosure having following specifications :-

ENGINE

Make : Cummins(Jakson)/Greaves/Kirloskar/Ashok Leyland

Engine Type : 4 Stroke Diesel Engine

Rated Output : 80 BHP or Higher

Duty : PRIME

Cooling : Water cooled with radiator

Cylinder : 4

Aspiration : Turbo Charged

Type of Governer : Electronic

Fuel Tank Capacity : Minimum capacity 150 Ltrs.

Fuel Consumption at 75% rated Load with Radiator or Fan : 12 Ltr./ Hr. or Less

Fuel Consumption at 100% rated Load with Radiator or Fan : 16 Ltr./ Hr. or Less

Overload Capacity : 10% overload for one hour for every 12 hours continious running at full load or better

Engine instrument Panel : Consisting of starting switch with Key, Lube Oil Indicator, water temperature Indicator, RPM indicator and hour meter.

Safety Controls : Emergency Stop, Low Lube Oil Pressure warning/ Shutdown, High Engine Water Temp. warning/ Shutdown, Sensor failure Indicator, Engine overspeed indicator, Battery charging and low battery indicator

Exhaust Silencer : Residential Type

Starting system : 12V. starting system complete with starter motor, charging alternator with rectifier and Cutout as per manufacturer standard.

Battery : Lead Acid, Low Maintenance or SMF and conforming to relevant IS Specification with Low/High Battery Voltage and Weak Battery warning

ALTERNATOR

Make: Stamford/Crompton Greaves /Kirloskar/ Ashok Ley Power

Rating : 415 V., 3Ph. 50 Hz., 62.5 KVA, 1500 rpm

Type : Brushless, self excited and self regulated

Insulation : Class H

Protection : screen-protected drip proof with Min.IP-23 degree of protection

Voltage Regulation (max) : ±1%

Winding connection : Star with Neutral

Total Distortion factor : Less than 3%

Total Harmonic distortion in output waveform : < 5%

AMF PANEL

Cubical type floor mounted AMF panel made from 16 SWG Sheet Steel, duly pretreated, powder coated painted and aesthetically finished, suitable for controlling of 62.5 KVA DG set having following specification/features.

i) 125A 36KA MCCB with O/L, S/C, E/F protection and microprocessor based protection release , U/V release etc. - 2Sets

ii) In Built By-Pass switch for rated capacity

iii) On -delay timer for load change over

iv) On-delay timer for engine shut off

v) Engine On-Off switch (Push button type)

vii) Minimum five number indicating lamps to indicate 'mains ON', 'load on mains', Set running', 'load on set' and 'battery charger on'.

viii) Audio visual alarm for 'Low lubricating oil pressure', 'High water temperature, Start failure', and DG over load'.

x) Microprocessor based relay with composite meter for digital display of following.

Generator voltage/AC Mains voltage.

Generator Current in all phases

Frequency

Power Factor

Energy

Indication for alternator supply

Running time indications number of hours of operation and service intervals, service due indications

The AMF panel must be designed to ensure trouble free performance and ensure switching over Electrical Load to DG within 15 (fifteen) second from the instant of mains failure.

ACOUSTIC ENCLOSURE

The DG set should have integrated acoustic enclosure at the manufacturing state itself. High quality acoustict enclosure must be certified as per CPCB-II norms.

BASE FRAME

Common iron channel fabricated base frame containing the engine and alternator, mounted on AVM pads and having provision for lifting Hook.

TERMS & CONDITIONS

(i) All materials, equipments & accessories must conform to relavent IS /IEC specifications. The DG Set to be supplied must be from the authorized OEM of the respective Engine Manufacturer.

(ii) Nacessary manufacturer's test certificate for Desiel Engin, Alternator etc. Will have to submit in triplicate copy during delivery of the equipment.

(iii) Copy of "Type Approval Certificate" and Certificate of "COP" must be produced at the time of delivery issued from competant Authority (As per CPCB-II).

(iv) Circuit Diagram for AMF Panel must be submited from the Manufacturer/OEM.

(v) The entire set must be warranted atleast 15 months from the date of Delivery/12 months/ 5000 Hrs from the date of Commissioning whichever is earlier. However Engine & Alternator should be warranted of 2 years/5000 Hrs, whichever is earlier.

Making CC & Brick foundation (10inch brick work) bellow 3ft from GL & 3 ft above GL. Of size. 8ft x 12ft incl. 3mm thick neat cement finish on all four sides & top. And also provide 3nos step at one side. Construction will be as per direction of EIC

Supply & Installation of exhaust pipe line connection with MS black pipe 100mm (4”) dia ISI approved, necessary nuts, bolts, washer, gasket incl. electrical welding where necessary.

Wrapping the Exhaust pipe line with Al. sheet high quality with necessary wire mesh & asbestos rope, cloth etc.as per direction of EIC.

Painting the MS black pipe, (3”) dia Aluminum paint of two coat over the RO primer. Approved make.

S&F 4" dia MS heavy type bend

S&F rain protection canopy.

Hot air ducting by S&F 16SWG CR sheet structure, necessary c.c work & painting.

S&filling HSD for immediate run &testing of DG set.

Supply & laying of 4core 70 Sqmm XLPE/AL cable Through UG Tranch As to GS (make : Polycab/havells/KEI)

Supply & Fixing LED wellglass Gighlumen fitting Philips make cat no- BYP LED 78S CW PSU HE PC/Crompton /Bajaj/Wipro)

Supplying& Fixing 40 Watt LED outdoor type post top lentran complete with all accessories (Crompton LPTO-40-CDL/Philips /Bajaj/Wipro)

R.T.ELECTRICALS

M/S. PROTIVA ELECTRIC WORKS

M.G.ENTERPRISE