PROVN OF HARDSTANDING AND DRAIN AT LOWER CAR PARKING FOOTPATH FROM BLDG NO P74 TO P105 REAR ENTRANCE GATE ANI TERMITE TREAMENT IN A MESS TOILET NEAR BLDG NO P 57 AGS BRANCH AT HQ NC ADDN ALTN TO BAR COUNTER AT A OFFRS MESS AT HQ NC ADDN ALTN OF

Amount

Surface dressing not exceeding 15 cm deep in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation or manholes etc and area not exceeding 10 sqm on plan and getting out in any type soil complete all as specified and directed.

PCC 1:4:8 type C-2 (using 40 mm graded aggregate) in foundation filling and mass concrete complete all as specified and directed.

Brick work with sub class 'B' brick, straight or curved on plan exceeding 6 m Mean radius built in type CM 1:6 complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Damp proofing course to horizantal or vertical surface including form work in PCC 1:2:4 type B-1 25 mm thick complete all as specified and directed.

Hardcore of guage not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

75 mm thick PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base floor complete all as specified and directed.

75 mm thick for PCC 1:3:6 (using 20 mm graded aggregate) as in plinth protection using extra cement complete all as specified and directed.

Non skid ceramic coloured tiles 400 x 400 x 7 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Glazed ceramic tiles in vertical surface but 600 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:6 on brick work and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:4 on brick work and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 5 mm thick in cement mortar 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and directed.

Preparation of new plaster surfaces wall surface applying three coats of white wash complete all as specified and directed.

Preparation of new plaster surfaces applying two coats of cement base paint and over one coat of primers complete all as specified and directed.

Preparation of new plaster surfaces applying three coats of white wash on ceiling complete all as specified and directed.

Form wotk to edges of concrete flat slats sides of RCC/PCC bands etc in walls horizental or slopping exceeding 10 cm but not exceeding 20 cm wide rough finished surfaces complete all as specified and directed.

Form work to soffits of suspended slabs and similar work not exceeding 200 mm thick complete all as specified and directed.

Form work to sides and soffit of floor or roof beams lintels, beam haunching, girders lintal cantiliver including supports overhung etc complete all as specified and directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded aggregate) for slabs supported on walls beams and columns in floors, roof, landing, balconies, canopies slabs and in shelves and the like complete all as specified and directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded aggregate) for for lintals bends and roof bends complete all as specified and directed.

TMT bars 10 mm dia and over and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9 mm dia or securing with clips quality confirming complete all as specified and directed.

Mild steel bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binder TMT bars cut to length bent to shape required including cranking, bending spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour sheet reinforced with MS square tube all as per specififcation and drawing and complete all as specified and directed by Engr-in-Charge.

Factory made solid PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be coverred with heat moulding plain colour PVC C channels having a PVC sheets strips of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, laock rail & bottom rail on either side &as gap insert for top rail & bottom rail panelling of plain colour PVC sheets to Be fitted in the MS frame welded/sealed to the stiles & rails with suitable complete all as specified and directed.

100 mm size butt hinges extruded aluminium alloy with galvanised with galvanised mild steel hinges pin anodised type B-2 complete all as specified and directed.

200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Aluminium handles cast type of 150 mm size complete all as specified and directed.

Steel Ventilators with top hung shutters including hinges steel peg stay complete all as specified and directed .

Sheet glass 3 mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in Each pane complete all as specified and directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and directed.

110 mm PVC (SWR) bends any redius with access door complete all as specified and directed.

110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and directed.

110 mm PVC (SWR) vent cowl complete all as specified and directed.

100 mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement in repair complete all as specified and directed.

100 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and directed.

100 mm PVC (SWR) bends any radius with access door complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and directed.

Vitreous china ware wash down water closet pan, (pedestal pattern) coloured including connection to drain and to flushing pipe, anti syphonage pipe etc. complete all as specified and directed.

10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and directed.

Vitreous china white wash hand basin (flat back or angle back type) size 550 x 400 mm white including brackets, pedestal, wast fittings brass chromium plated, CP waste coupling, 32 mm dia, waste pipe, PVC connection 15 mm bore with PTMT nuts of length including 15 mm dia CP piller tap fancy type complete all as specified and directed.

Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe in repair complete all as specified and directed. Make : CERA Cat Part No F8030103 or equvalent in Prayag/ESSCO

Chromium plated toilet paper holder complete all as specified and directed. Make : Jaquar Cat Part No ACN 1153N and equvalent in Prayag/ESSCO.

Glass shelf with chromium plated guard rails complete all as specified and directed. Make : Jaquar, Cat Part No ACN-1171N and equvalent in CERA/Prayag/ESSCO.

600 mm long brass chromium plated towel rail fancy type complete all as specified and directed. Make : Jaquar Cat Part No ACN-1111NM and equvalent in CERA/Prayag.

Soap dish complete all as specified and directed. Make : Jaquar Cat Part No : ACN 1131N and equvalent in CERA/Prayag.

Taking out any type of cables, pipes or any type of utilities found above or benith the ground level and laying/reconnecting the same away from working area/site, including material and labour utilised in the same complete all as specified and directed.

Providing and injecting chemical emulsion for Post constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 ltr per sqm of the vertical surface of the sub structure to a depth of 300 mm including excavated channel along the wall and rodding etc complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Providing and injecting Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Providing and injecting of voids in masonry using chemical emulsion one litre per hole, at 300 mm intervals including drilling holes complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment and drilling holes at 45 degree and plugging the same with cement mortar 1:2 to match with existing surface.

Providing at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Half stall urinal flat back (large) 635 x 395 x 420 white colour complete all as specified and directed. Make : CERA Cat Part No : 5001 or equivalent Prayag/ESSCO.

CP waste coupling 32 mm dia PTMT (half or full threaded) minimum weight 450 gms complete all as specified and directed.

PVC waste pipe 32 mm bore with cup and washers complete all as specified and directed.

15 mm bore centre hole basin mixer with round spout with 450 mm long copper pipes and brass nuts with out Pop up complete all as specified and directed. Make : Jaquar, Cat Part No CON 167KNB or equivalent Prayag/ESSCO.

Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and directed. Make : Jaquar Cat Part No : PRS 077 or equivalent Prayag/ESSCO.

PVC connection 15 mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer (Suitable for Basin Mixers) complete all as specified and directed. Make: Jaquar Cat Part No-ALD-803AB or equivalent Prayag/ESSCO.

PVC connection 15 mm bore 450 mm long Braided Hose with two 15 mm Nut & Rubber washer without nipple complete all as specified and directed. Make: Jaquar Cat Part No - ALD-805B or equivalent Prayag/ESSCO.

CP Bib taps cast copper alloy with crutch or butterfly handle two bay, screwed for iron pipe of dia 15 mm, fancy type fixed complete all as specified and directed.

CP angle valves cast copper alloy, fancy type, with iong shank and cup, bore 15 mm fixed complete all as specified and directed.

125 mm dia brass chromium plated shower rose with swivel joints complete all as specified and directed.

600 mm long tubular tower rail brass chromium plated 20 mm dia, D type 60 cm long fixed with two plugs (Gutties) of 2nd class hard woodembeded in cement mortar 1:3 with MS screws complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 ltrs (cylindlerical verrtical with closed top) hoisted and fixed in position all as specified in SSR part I including dismantaling of existing damaged water tanks complete all as specified and directed.

20 mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed for iron pipes complete all as specified and directed.

Roughing surfaces of old conc surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20 mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separatley) complete all as specified and directed. Note : No extra cost shall be paid to contractor in without any removal of existing roof treatment.

3 mm thick plain polymeric water proofing membranse of weight not less than 3.5 Kg per Sqm and bonded completely to the surfaces with overlap of 10 cm (overlap to be thermo fused by flame) to be laid by company complete all as specified and directed by Engr-in-Charge.

Supply only (LW+) water proofing liquid solution complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete type D-2 (1:4:8) for 150 mm dia pipe complete all as specified and directed.

SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM (1:4) as in manholes, septic tank, filter bed, walls, drains etc complete all as specified and directed.

Cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as in foundation filling and mass concerete complete all as specified and directed.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and directed. Note :- reinforcement will be measured and paid seperately.

100 mm PCC 1:4:8 type D-2 (40 mm graded aggregate) as in sub base to floor complete all as specified and directed.

15 mm thick screed bed or bedding layer of mortar for laying floor finishes in CM 1:4 complete all as specified and directed.

Cement concrete colored chequered tiles machine pressed with imported pigment finish (gloosy finish) of size 300 mm x 300 mm x (30 to 40 mm) tcick set and jointed with neat cement slurry complete all as specified and directed.

Kerb stone of size 300 mm x 300 mm x 100 mm thick made of precast cement concrete 1:2:4 type B-0 (using 12.5 mm grated crushed stone aggregates) including earth work for laying kerb stone, complete all as specified and directed by Engr-in-Charge.

Applying two coat of rubber chlorinated high build coating synthetic enamel paint on concrete surfaces over a coat of primer including necessary preparation complete all as specified and directed Engr-in-Charge.

Dismantling timber scantlings 40 sqcm and over in section, in any position and in un framed work complete all as specified and directed.

First class hard wood wrought in scantling, decorative design work approved and complete all as specified and directed by Engr-in-Charge such as decorative balustar.

Dismantling of wall wooden panelling in any any position complete all as specified and directed.

18/19 mm thick block board, grade 2 quality, interior grade, commercial type fixed with screws to timber frame work/iron frame work (Termite treated/water proof) complete all as specified and directed.

Plywood 12 mm, grade BWR, type BB, fixed with screws to timber frame work on wall/ ceiling and similar work and complete all as specified as per direction of Engr-in-Charge.

0.9 mm thick decorative choice of lamination type-1 of surface finish, colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and directed.

French polishing on wooden surface of any description, width or girth including cleaning and preparing the surface incl a coat of wood filler on old decorative surface complete all as specified and directed.

10-12 mm thick gypsum boards seemess decorative false ceiling as in ceiling plain (Designe approved by GE), moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rowel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface, complete all as specified and directed by Engr-in-Charge. Note : (a) Design of ceiling board as approved by Engr-in-Charge. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surface in CM 1:4 on vertical surfaces/backing coat complete all as specified and directed.

20 mm thick granite (of any type) machine cut as in dado etc laid over cement backing coat and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grainding and polishing complete all as specified and directed by Engr-in-Charge.

Brass railing, foot rest bar and similar work confirming to superior Gde complete all as specified and directed by Engr-in-Charge.

Rolled Mild steel sections as in frame work for structure, main and cross beams hip and jack rafters, purlines fixed independently and similar work including welding complete all as specified and directed by Engr-in-Charge.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Preparation of old surfaces of any description over 10 cm in width of grith and applying two coat of varnishing complete all as specified and directed.

Preparation of surface and applying textured painting (granular or impression type), any colour and any position complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete in ground floor and paving not exceeding 15 cm thickness below and above ground level complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded aggregate) as in level course on floor etc complete all as specified and directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and directed.

Vitrified ceramic tiles (Double charge), polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, 10 mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the dark shade/any shed of tiles complete all as specified and directed.

Sand cushioning under floors including watering and consolidation complete all as specified and directed.

80 mm thick factory made reflective type, heavy duty, smooth finish cement concrete inter locking paver block of M-40 grade made by block making machine with strong vibrating compaction casted in rubber/Pu mould on a vibrating table of approved size and design/shape laid in required vibrating machinne complete all as specified and directed by Engr-in-Charge.

PCC 1:3:6 type C-2 (using 20 mm graded aggregate) as in foundation/sub base, filling and mass concrete complete all as specified and directed.

Factory made precast cemet concrete kerb stone of PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) of approved shape and size and design/shape laid in required colour and patter over and including 50 mm thick compacted bed of coarse sand filling the joints with coarse sand etc including vibrating the surface with vibrating machine complete all as specified and directed by Engr-in-Charge.

Stone walling of random rubble uncoursed, well bonded, bedded and solidly hearted built in CM (1:6) complete all as specified and directed.

Flush pointing to random rubble masonry, uncoursed or brought upto courses in 1:4 complete all as specified and directed.

PCC type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in surface channels and drain beds complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and ageraging 15 cm deep and getting out in hard and dense soil complete all as specified and directed.

Sand cushion 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and directed.

Machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engr-in-Charge.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1 (20 mm graded crushed stone aggregate), kerb stone & the like of size 300 mm x 300 mm x 100 mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc. embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance not exceeding 50 m from the starting point complete all as specified and directed.

Ceramic coloured tiles of size 600 x 300 x 7-8 mm/450 x 300 x 7-8 mm (stone finish/rough finished surface) wall tiles set and jointed in neat cement and in white/coloured cement to match with the colour of tile etc. complete all as specified and directed.

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar complete all as specified and directed.

Preparation of new plaster surface of walls and applying two coats of oil bound distempers over one coat of primer and two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Framed work such as doors, gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding eith and including either hooks and hinges or steel hanging door fittings including ornament and intricate design, including pintle hings, stops hand made sliding bolts etc confirming to Fe 290 Gde-E-165 complete all as specified and directed.

Stainless steel (Grade 304) formation sign, comd insignia and similar ornamentel work including fixing with nut and bolt, rivetted, welded or soldered at joints complete all as specified and directed by Engr-in-Charge.

Complete removal of existing treatment from external surfaces of walls by wire brushing and washing, rubbing down and stopping of surfaces and leveling/edging the disturbed planes/edges using necessary filling compound of Altek putty to obtain smooth regular/even finish using sand paper and applying two coats of exterior emulsion paint 1st quality paint complete all as specified and directed by Engineer-in-Charge. The tint/shade of the paint shall be as approved by the GE.

Complete removal of existing treatment and applying two coats of oil bound distemper with using roller over a coat primers with two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Dismantling Asbestos cement (corrugated or semi corrugated) sheets as in roof covering complete all as specified and directed.

Pre-painted galvatume aluminum zinc coating GI vased corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

MS flat iron as in wind ties etc confirming to Fe 410-0 or Fe 310-0 including clamps complete all as specified and directed.

Rolled section as in main and cross beams, purlins, rafters, posts where connected to common rafter and running rails, eves board framing work, tank staging work etc confirming to Fe-410-W complete all as specified and directed.

1.25 mm thick plain black mild steel sheeting in ridges hip, valley gutters drip and gutters and straight flashings (Length and girth as fixed) in repair complete all as specified and directed.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members, frame etc complete all as specified and directed.

Providing false ceiling GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flages of 20 to 30 mm and web of 27 mm fixed to surrounding wall using screws at 452 mm C/C channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm C/c with GI cleat and steel expansion or sutable hanging from soffits\trusses\bracking supporting hanger compressing of GI wire complete all as specified and directed by Engr-in-Charge.

4 mm thick 600 x 600 mm size asbestos cement plain E-boards designer ceiling complete all as specified and directed. Make : Everest of equvalent, fixed to GI grid work with screws and applying new surfaces two coat of distempers and one coat of primers.

Dismantling of cast iron or reinforced concrete drain pipe 100 mm dia and below jointed in cement mortar and taking out of floor/walls etc complete all as specified and directed.

Demolition of reinforced cement work as in roof slabs (other than ground floors) beams staircases, landing chajjas and similar suspended work complete all as specified and directed.

Reinforced cement concrete M-25 (20 mm graded aggregate) as in slab supported on walls, beam and columns in floors,roofs landings, balconies etc. complete all as specified and directed.

Non skid ceramic joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the slurry complete all as specified and directed.

10 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:3 as in backing coat to recieve tiles as in vertical surfaces and finished even and fair complete all as specified and directed.

Dismantling boarding any description any description fixed in any position with nails complete all as specified and directed.

IInd class soft wood as in plian solid straight chowkhats wrought framed rebated on the solid put together on with glue pinned at joints complete all as specified and directed.

Stain less steel catcher of superior quality complete all as specified and directed by Engr- in-Charge.

50 mm stain less steel pivoted type hinges of superior quality and complete all as specified and directed by Engr-in-Charge.

Aluminium 65 mm mortice lock four levers complete all as specified and directed. (ISI Marked)

Aluminium anodised barrel tower bolts of extruded section with 75 mm long bolt complete all as specified and directed. (ISI Marked)

Drawer side channel of std size and including of rooler for moving drawer, mild steel bright finish or electrogalavanised width of flap 30 mm & Length 60 mm in repair complete all as specified and directed.

Stainless steel fancy type, bright finish handles fixed with screw, of 125 mm size in repair complete all as specified and directed.

Stainless steel multipurpose basket in wooden drawer/partitions for storing rations of various types made of 4 mm dia stainless steel rods, fixed in side partitions etc fixed in repair complete all as specified and directed for modular kitchen.

Stainless steel luddle-craddle hanging stand for cutlery in repair complete all as specified and directed by Engineer-in-Charge for modular kitchen.

Stainless steel zero crank hinges (auto) fancy type (with Euro concealed hinges) fixed to shutters in cupboards of standard size and shape for modular kitchen in repair complete all as specified and directed by Engr-in-Charge.

1.00 mm thick stainless steel single bowl Sinks with plugs, washers and wastes; including fixing contilever brackets and connecting union to pipe (size of bowl 410 mm x 330 mm x 160 mm) in repair complete all as specified and directed.

Recessed type stain less steel handle for cup boards size 75 mm long complete all as specified and directed.

Taking up or down GI tubing of 15 mm bore and connectios, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down GI tubing of 20 mm bore and connectios, including cleaning for refixing or removal to store complete all as specified and directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 15 mm bore including taking down old pipe complete all as specified and directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 20 mm bore including taking down old pipe complete all as specified and directed.

15 mm bore long body Bib tap in repair complete all as specified and directed. Make : Jaquar, Cat Part No CON-037KN or equivalent in Prayag/ESSCO

15 mm dia brass chromium plated sink mixer, hot and cold water fancty type fixed with iron pipe complete all as specified and directed.

15 mm bore Bib tap in repair complete all as specified and directed. Make : Jaquar Cat Part No CON 107KN or equivalent Prayag/Kohler.

15 mm bore angular stop cock with wall flange in repair complete all as specified and directed. Make : Jaquar Cat Part No CON-059KN or equivalent Prayag/Kohler.

75 mm bore cast iron floor trap with grating including jointing to waster pipe fixed in cement concrete type B-1 1:2:4 in repair complete all as specified and directed.

Hand rails, half round or other steel section or core for wooedn hand rail straight portion, drain cover with framed work, wind ties for roof and flat iron for drain cover including securing bolts, drilling holes, notching for wire, all necessary drilling, bolting or riveting, welding etc confirming and similar work to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work up to G+2 height bldg including cutting of brick/concrete wall and fixing of hold fast and making good, confirming to Fe.290.Gde-E-165 complete all as specified and directed.

PCC 1:2:4 type B-0 (using 12.50 graded aggregate) for coping, hold fast, corner of roof and similar work complete all as specified and directed.

Complete removal of existing treatment applying two coat of cement base paint over a coat of primer paint on walls complete all as specified and directed by Engr-in-Charge.

Vitrified ceramic tiles, area of each tile not exceeding 0.36 sqm, 10 mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

15 mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic colored tiles as in vertical surfaces 350 x 250 x 7 mm/450 x 350 x 7 mm/ 300 mm x 600 mm thick set and jointed in neat cement slurry and pointed with white or colored cement to match complete all as specified and directed.

Vitrified coloured heavy duty (Dura stone) 300 x 300 x 10 mm thick tiles as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

PVC wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per site requirement complete all as specified and directed by Engr-in-Charge.

10 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing to wall to make pvc frame as per site requirement. complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered or un-plastered surfaces and walls including cornices, pilasters etc and applying two coats of weather coat paint over a coat of primer complete all as specified and directed.

Disconnecting existing tanks of exceeding 500 but not exceeding 1000 ltr capacity setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position with cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc. complete all as specified and directed.

Demolition and beaking up drain AC pipes/PVC pipe set in cement mortar 150 mm and below complete all as specified and directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and directed.

110 mm PVC (SWR) bends any redius without access door complete all as specified and directed.

110 mm PVC (SWR) couplers for PVC pipe and similar work complete all as specified and directed.

Vitreous china EWC Super Constellation including cistern of size 83 x 37 x 66 cm 'S' trap as per Cat Part No. 20032 (S-10/P-19) for EWC & Cat Part No. 21050 for cistern of in repair complete all as specified and directed. Make : Hindware or equivalent in Parryware.

Vitreous china Wash Hand Basin Constellation starwhite including pedestal of size 570 x 480 mm fixed with bracket including CP waste coupling, PVC waste pipe 32 mm dia chain & plug porcelene stopper and other necessary fittings in repair complete all as specified and directed. Cat Part No : 10032 for wash basin & Cat Part No : 11010 for pedestal of Make : Hindware or equivalent in Parryware/CERA.

Vitreous china ware Urinal starwhite flat back as approved including fitting and fixtures including PVC waste pipe and one CP stop cock 15 mm dia and other necessary fittings in repair complete all as specified and directed. Make : Hindware or equivalent in Parryware/CERA.

PCC type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and directed.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power/LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed. Keeping the LED lights in safe custody.

Point wiring for one light/fan/bell point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes thickness (1.25 mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed.

All as per ser item No 186 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 186 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 186 but for 3 Pin 15 Amps socket outlet independent with cable 4.0 Sqmm including copper PVC insulated PVC unsheathed 2.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed.

Socket 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and directed.

Socket 2-in-1, 3 Pin 6 & 16 Amps (Modular Type) with outer strip complete all as specified and directed.

Electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as specified and directed.

Ceiling rose surface bakelite 3 terminals complete all as specified and directed. Make : Cona Cat Part No 2126/SSK Cat Part No 572 or equivalent of make in Havells/Anchor/Kolors/Legrand.

Single pole and neutral enclosure surface mounted 240 volts with 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of make wipro/equivallent in Havells/ Bajaj complete all as specified and directed.

12 W LED 300K Recess mounting AI die-casted swivel fixture with separate dimmable driver with bigger collar size. Make - Havells Cat Part No LHEBJTPBUH1W012 or equivalent to Polycab/ HPL/Bajaj complete all as specified and directed by Engineer-in-Charge.

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W Make - Havells Cat Part No LHEXBXPNIN1W020 or equivalent to Polycab/HPL/Bajaj complete all as specified and directed by Engineer-in-Charge.

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 8 way 240 volts with 200 amps rated bus bar and neutral link in cluding chases wall for dixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make - INDOASIAN Cat Part No-KSLS0012 or equivalent LEGRAND/ABB/ STRENDED

Replacement MCB Single Pole, 230 Volt, Raiting 6 to 32 Amps complete all as specified and directed. Make : Indoasian Cat Part No : 811015 or equivalent Legrand/Stanard

Replacement MCB Single Pole and Neutral , 230 Volt, Raiting 35 to 63 Amps complete all as specified and directed. Make : Indoasian Cat Part No : 811037 or equivalent Legrand/ Stanard

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 4 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 6 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire.

Earthing complete with galvanised steel earth plate electode 600 mm x 600 mm x 6.00 mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20 mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board as specified and testing completion complete all as specified and directed.

Point wiring for one light/fan/bell point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes thickness (1.25 mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed.

All as per ser item No 205 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 205 but for 1 Pin 15 Amps socket outlet independent with cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Exhaust fan Ventil Air-DB 300 mm including louver & making hole for Exhaust fan works complete all as specified and directed. Make - Havells/Polycab/Bajaj.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately.

Replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) Cat Part No. LHEOAOP7UZ6W010 230 Volts wall/surface mounted complete with with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge.

Garnet Batten 5W LED Mirror light Product complete all as specified and directed. Make: Wipro/Havells/Philips

36 W LED edge-lit luminaire suitable for armstrong/rigit ceiling complete with separate electronic driver complete all as specified and directed. Make : Havells Cat Part No - LHECDIL6PP1W036 or equivalent in Wipro/Philips

LED Street light 30W including angle arms (Bracket) with 25 mm dia GI pipe. complete all as specified and directed by Engineer-in-Charge. Make- Wipro Product Code- D923065 or equivalent to Havells /HPL/Bajaj

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2 x 6 Sqmm FRLS in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 1 x 4 Sqmm FRLS as earth lead complete all as specified and directed. Including taking down old sub main wire.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.30 mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead 4 mm dia by means of bolts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and indicated and testing on completion including excavation earth work drilling holes for electrode PCC pit & cover, funnel, water pipe lugs GI pipe medium grade protection pipe for earth lead up to DBs. complete all as specified and directed.

35 W LED gate light new generation, post-top, energy saving, environmental friendly, long life aesthetically designed with food indirect symmetrical light distribution, die-cast aluminium landscape IP65 luminaire with high power COB LED as light source suitable for pole dia 76 mm complete all as specified and directed. Make :- Havells or equivalent to Philips/Bajaj/ C&S,

Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 2.00 mm thick 20 mm dia and over Non metallic Rigid PVC surface /Concealed Conduit (ISI marked) with and all accessories 1.5 mm thick mild steel terminal boxes concealed on walls, painting the same inside and out side with one coat of black bitumen paint with 3 mm thick hylam brand bakelite sheet cover for fixing of piano switches/ sockets/regulator etc along with PVC insulated and unsheathed FRLS 1.00 sqmm multi stranded copper conductor cable (green color) as earth lead & connected to common earth and earthdolly, making good the disturbed surface to match with the existing specification complete all as specified and directed by Engr-in-Charge. Make - KEI or equivalent make in polycab/finolex

All as per ser item No 217 but for one 3 pin 5 Amp socket outlet point controlled by one push button on same board complete all as specified and directed.

All as per ser item No 217 but for one 3 pin 5 Amp socket outlet point controlled by one push button on independent board, cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

All as per ser item No 217 but for one 3 Pin 15 Amps socket outlet independent with cable 4.0 Sqmm including copper PVC insulated PVC unsheathed 2.5 sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch piano flush button single pole one way 5 amps 240 volt in repair complete all as specified and directed.

Socket outlet 2 in 1, 3 pin, 5A, 240 Volt in repair complete all as specified and directed.

Switch socket combination 5 Amps 2-in-1, 5 Pin flush type, 230 volts in repair complete all as specified and directed.

Switch socket combination 5 pin 16 amp, flush type in repair complete all as specified and directed.

Fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically in repair complete all as specified and directed.

Replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 5 W Make- Havells Cat Part No LHEXBXPNIN1W005 or equivalent to Polycab/HPL/Bajaj complete all as specified and directed by Engineer-in-Charge.

Replacement of Maple 40 W gate light post top for 360 degree indirect light with IP 65 protection resistant to impact and corrosion. glare-free and better uniformity complete all as specified and directed by Engineer-in-Charge. Make - Crompton Cat Part No LPTO-40-CDL or equivalent to Polycab/HPL/ Bajaj

Replacement of wall mounting, SS finish fixture with opal PC diffuser suitable for 40W incandescent including 7W LED candle lamp complete all as specified and directed by Engineer-in-Charge. Make - Havells Cat Part No LHJE01104499 or equivalent to Polycab/HPL/Bajaj

Re-fixing only Ceiling fan/Exhaust fan/Energy Meter and cable of existing fans complete all as specified and directed Engr-in-Charge.

Trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 10 Sqmm x 2 core size complete all as specified and directed. Make - KEI, Finolex & Polycab. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and directed.

GI tubing light grade 40 mm dia along the wall/ in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and directed.

VARDHMAN INTERNATIONAL

s l sharma and sons

AKBAR FURNITURE HOUSE AND TIMBER MERCHANT