REPAIR/ MAINTENANCE/ SERVICING OF SEWAGE TREATMENT PLANT INCL MISC WORK OF DG SET, LAUNDARY PLANT, OHT CRANES AND ARBORICULTURE WORK UNDER AGE E/M-II OF GE (SOUTH) MEERUT CANTT

Amount

Material and labour for servicing ,overhauling, oiling , greasing and aligment vertically of Industrial type Steam Boiler of capacity 400 Kg, washer extractor, drying thumbler, flat bed press, vaccum finishing table etc. complete with testing on fully functional as per the guide line by OEM recommendation with the satisfaction of GE(S) Meerut Cantt. Note: Cost of spare parts shall be paid seperately.

Supply only steam boiler hose pipe of existing size including SS clamps with nuts and bolts make air tight and testing on full efficiency of the plant with the satisfaction of Engr-in- Charge.

Supply only steam valve for 32/25 mm bore pipe ISI marked and testing on full efficiency of the plant with the satisfaction of Engr-in- Charge.

Supply only insulation of steam pipe line 32/25 mm outer dia complete with glass wool, SS neting and covered with aliminium foil complete with work all as directed at site by Engr - in - Charge.

Supply only electronic control panel including complete wiring / electric supply connection of washer extractor of capacity 30 Kg complete and testing with the satisfaction of Engr-in- Charge.

Supply only copper steam pipe line 15mm dia including short piece and connecting , jointing ,bending , to required shape through gas welding for electric hand operating press table with testing on full pressure complete all as directed by Engr- in Charge.

Supply only flanges off sizes for copper steam / pressure pipe line complete with rubber gasket nuts and bolts all as directed at side .

Supply only copper conductor cable of size 3 core 40/0.0076 for electric hand operated press all as directed at site.

Supply only solenoid valve 15 mm dia ISI marked for steam line to electric hand operating press table complete all as specified and directed.

Supply only SS door handle with latch complete all as specified and directed.

Supply only foot valve for steam boiler as per existing all as specified and directed.

Supply only water level controller for seam boiler all as specified and directed.

Supply only plug / switch for pneumetically press as per existing complete all as specified and directed.

Supply only heater of capacity 6 KW complete all as specified and directed.

Material and labour for servicing ,overhauling, oiling , greasing and aligment vertically of Industrial type washing machine of capacity 70/35 KG. complete with testing on fully functional as per the guide line by OEM recommendation with the satisfection of GE(S) Meerut Cantt. Cost of under mentioned spare parts shall be paid under respective items .

Supply only fan belt "V' type as per existing size and make complete all as specified

Supply only main ball bearing washing machine complete all as specified and directed.

Supply only main ball bearing sleeve washing machine complete all as specified and directed.

Supply only idler ball bearing washing machine complete all as specified and directed.

Supply only idler ball bearing sleeve washing machine complete all as specified and directed.

Material and labour for servicing ,overhauling, oiling , greasing alingment of Industrial type washing machine of capacity 15 KG. complete with testing on fully functional as per the guide line by OEM recommendation with the satisfection of GE(S) Meerut Cantt. Note: Cost of spare parts shall be paid seperately.

Supply only operating computor ST-9 complete unit with connecting and testing complete all as specified.

Supply only ball bearing front of NU 2214 complete unit with connecting and testing complete all as specified of suitable size all as specified and directed.

Supply only ball bearing rear 6212Z complete unit with connecting and testing complete all as specified of suitable size all as specified and directed.

Supply only 'O' ring set complete unit with connecting and testing complete all as specified of suitable size all as specified and directed.

Supply only oil seal viton complete unit with connecting and testing complete all as specified of suitable size all as specified and directed.

Supply only oil seal - nitrile complete unit with connecting and testing complete all as specified of suitable size all as specified and directed.

Supply only circlip lock set complete unit with connecting and testing complete all as specified of suitable size all as specified and directed.

Supply only fan belt "V' type as per existing size complete all as specified and directed.

Supply only drain Valve complete all as specified and directed.

Supply only 'L' shape drain hose pipe of size 3" dia complete all as specified and directed.

Supply only drain hose pipe straight of size 3" dia complete all as specified and directed.

Supply only emergenct stop push button complete all as specified and directed.

Supply only door gasket complete all as specified and directed.

Supply only variable frequency drive complete all as specified and directed.

Material and labour for servicing ,overhauling, oiling , greasing alingment of Industrial type tumbler machine of capacity 15 KG. complete with testing on fully functional as per the guide line by OEM recommendation with the satisfection of GE(S) Meerut Cantt. Note: Cost of spare parts shall be paid seperately.

Supply only operating computor DR-9 complete unit with connecting and testing complete all as specified

Supply only "V' belt main drive complete all as specified

Supply only "V' belt idler drive complete all as specified

Supply only thermostat switch 30-110 complete all as specified

Supply only door gasket complete all as specified

Supply only door limit switch complete all as specified

Supply only lint door gasket complete all as specified

Supply only blower alluminium cast complete all as specified

Supply only contractor AC 3 phase 415 volt 18 Amps complete all as specified

Supply only heater contractor AC single phase 230 volt 25 Amps complete all as specified

Supply only teflon copper electric cable 6 Sqmm 3 core AC 1100 volt grade compete all as specified and directed

Material and labour for servicing ,overhauling, alingment of press table of any type. complete all as specified and directed . Note: Cost of spare parts shall be paid seperately.

Supply only of blower alluminium complete all as specified

Supply only silicon foam padding complete all as specified

Supply only padding cloth cover complete all as specified

Supply only thermostat switch of range 50-300 complete all as specified

Supply only electric steam iron single phase 230 volt complete all as specified

Supply only teflon shoe for iron complete all as specified

Supply only thermostat for iron complete all as specified

Supply only water level switch ( double micro switch) complete all as specified

Supply only water level controller ( WLCD1) complete all as specified

Supply only buzzer AC 230 volt complete all as specified

Supply only sensor switch AC 230 volt complete all as specified

Material and labour for servicing ,overhauling, oiling , greasing and testing including caliberation of EOT Crane of capacity 10 Ton installed at 609 EME Bn and checking all movement , load capacity , brake system and smooth functioning of the Crane with the satisfection of GE(S) Meerut Cantt.

Material and labour for servicing ,overhauling, oiling , greasing and testing including caliberation of EOT Crane of capacity 2.0 / 5.0 Ton installed at 609 EME Bn and checking all movement , load capacity , brake system and smooth functioning of the Crane with the satisfection of GE(S) Meerut Cantt.

Disconnecting and dismanteling including up / down of unserviceable air blower motor of capacity 17.5 HP 3 phase 415 volt and transportation to auth / recognised workshop for repair to slip ring motor ,removing the existing copper burnt wire from rotor as well as statar, cleaning the slots thoroughly and rewinding the statar and rotor of motor capacity 17.5 HP with supper enameled copper conductor of existing gauge and turns including insulating material like, insulating paper , sleeves and varnishing complete reset the motor with testing on full load to achieve the efficiency of crane .

Supply only carbon brush suitable for 17.5 HP motor of existing size and approved by Engr-in- Charge.

Supply only carbon brush holder suitable for 17.5 HP motor of existing size and approved by Engr-in- Charge.

Supply only ball bearing suitable for 17.5 HP motor of existing size ISI Marked all as specified and directed

Supply only bearing cover sheet suitable for 17.5 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Supply only rotor sheet suitable for 17.5 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Disconnecting and dismanteling including up / down of unserviceable air blower motor of capacity 15 HP 3 phase 415 volt and transportation to auth / recognised workshop for repair to slip ring motor ,removing the existing copper burnt wire from rotor as well as statar, cleaning the slots thoroughly and rewinding the statar and rotor of motor capacity 15 HP with supper enameled copper conductor of existing gauge and turns including insulating material like, insulating paper , sleeves and varnishing complete reset the motor with testing on full load to achieve the efficiency of crane .

Supply only carbon brush suitable for 15 HP motor of existing size and approved by Engr-in- Charge.

Supply only carbon brush holder suitable for 15 HP motor of existing size and approved by Engr-in- Charge.

Supply only ball bearing suitable for 15 HP motor of existing size ISI Marked all as specified and directed

Supply only bearing cover sheet suitable for 15 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Supply only rotor sheet suitable for 15 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Disconnecting and dismanteling including up / down of unserviceable submersible pump motor of capacity 10.0/7.50 HP 3 phase 415 volt and transportation to auth / recognised workshop for repair to slip ring motor ,removing the existing copper burnt wire from rotor as well as statar, cleaning the slots thoroughly and rewinding the statar and rotor of motor capacity 7.50 HP with supper enameled copper conductor of existing gauge and turns including insulating material like, insulating paper , sleeves and varnishing complete reset the motor with testing on full load to achieve the efficiency of crane .

Supply only carbon brush suitable for 10.0/7.50 HP motor of existing size and approved by Engr-in- Charge.

Supply only carbon brush holder suitable for 10.0/7.50 HP motor of existing size and approved by Engr-in- Charge.

Supply only ball bearing suitable for 10.0/7.50 HP motor of existing size ISI Marked all as specified and directed

Supply only bearing cover sheet suitable for 10.0/7.50 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Supply only rotor sheet suitable for 10.0/7.50 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Lowering the submersible pump carefully in sewage sump well 25 feet deep and connecting all pipe line connection with the help of chain pulley and tepoy stand upto capacity of pump 10.0/7.50 HP including testing complete all as directed at site.

Disconnecting and dismanteling including up / down of unserviceable air blower motor of capacity 5.0/4.0 HP 3 phase 415 volt and transportation to auth / recognised workshop for repair to slip ring motor ,removing the existing copper burnt wire from rotor as well as statar, cleaning the slots thoroughly and rewinding the statar and rotor of motor capacity 5.0 HP with supper enameled copper conductor of existing gauge and turns including insulating material like, insulating paper , sleeves and varnishing complete reset the motor with testing on full load to achieve the efficiency of crane .

Supply only carbon brush suitable for 5.0/4.0 HP motor of existing size and approved by Engr-in- Charge.

Supply only carbon brush holder suitable for 5.04.0 HP motor of existing size and approved by Engr-in- Charge.

Supply only ball bearing suitable for 5.0/4.0 HP motor of existing size ISI Marked all as specified and directed

Supply only bearing cover sheet suitable for 5.0/4.0 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Supply only rotor sheet suitable for 5.0/4.0 HP motor after removal of unsv sheet and cleanining complete all as specified and directed.

Material and labour to repair the unserviceable submersible pump three phase 415 Volt of capacity 4.0 HP by recognised/ auth workshop ,segregate the pump and motor separately removing old burnt winding wire cleaning the slotes and rewinding of submersible motor with PVC insulated copper conductor of existing gauge and turns including insulating material like, paper ,sleeves and varnishing complete reset the pump and motor with testing on full load to achieve the efficiency of pump for the satisfection of Engr-in-Charge.

Supply only ball bearing suitable size for 4.0 HP pump motor including fixing complete with nuts and bolt as required and all as directed .

Supply only oil sheel of existing size and approved by Engr-in- Charge.

Supply only machenical sheel holder of existing size and approved by Engr-in- Charge.

Lowering the submersible pump carefully in sewage sump well 25 feet deep and connecting all pipe line connection with the help of chain pulley and tepoy stand upto capacity of pump 4.0 HP including testing complete all as directed at site.

Material and labour to repair the unserviceable submersible pump three phase 415 Volt of capacity 2.0/1.5 HP by recognised/ auth workshop ,segregate the pump and motor separately removing old burnt winding wire cleaning the slotes and rewinding of submersible motor with PVC insulated copper conductor of existing gauge and turns including insulating material like, paper ,sleeves and varnishing complete reset the pump and motor with testing on full load to achieve the efficiency of pump for the satisfection of Engr-in-Charge.

Supply only ball bearing suitable size for 2.0/1.5 HP pump motor including fixing complete with nuts and bolt as required and all as directed .

Supply only oil sheel of existing size and approved by Engr-in- Charge.

Supply only machenical sheel holder of existing size and approved by Engr-in- Charge.

Lowering the submersible pump carefully in sewage sump well 25 feet deep and connecting all pipe line connection with the help of chain pulley and tepoy stand upto capacity of pump 2.0 HP including testing complete all as directed at site.

Replacement of cloth pin for mechanical filter press machine having 24 Nos of slots in each Machine complete all as directed by Engr-in- Charge.

Replacement of filter cloth for mechanical filter press machine having 24 Nos of slots in each Machine complete all as directed by Engr-in- Charge..

Supply and mixing dewatering polyelectrolyte ( DWP ) powder standard grade HDPE packed complete all as directed by Engr -in- Charge. (0.75ltr/day/100KLD x 335 days)-700 KLD, 500 KLD, 400 KLD, 200 KLD) complete all as specified and direcred .

Testing of raw sewage and treated water in NABL / Govt approved lab on monthly basis for following tests for each plant and submitting to the department . (i) TSS ( Total solid suspended ) . (ii) COD (Chemical oxygen demand ) . (iii) BOD ( Biochemical oxygen demand ). (iv) FCT ( Faecal cloiform test ). (v) TCT ( Total cloiform test ). (vi) Odour test (vii) PH value test. Note :- Cost of collection of sample , packing and forwarding to lab for testing is included in this item.

Supply and mixing sodium hypo chloride for chlorination all as directed by Engr-in- Charge. (5 ltr/day/100KLD x 335 days for each plant - 700 KLD, 500 KLD, 400 KLD, 200 KLD) complete all as specified and direcred .

Supply and mixing poly aluminium chloride all as directed by Engr-in- Charge (0.3 ltr/day/100KLD x 335 Days for each plant - 700 KLD, 500 KLD, 400 KLD, 200 KLD) complete all as specified and direcred .

Supply & filling/top up lubricanting oil SP-320 for air blower/submersible motor etc.

Supply & filling/top up hydrolic oil SP-320 for air blower/submersible motor etc.

Supply and mixing bleaching powder for each plants all as directed by Engr-in- Charge.

Disconnecting and dismanteling unserviceable centrifugal pump electric drive 3 phase 415 volt 25.0 HP satisfection of Engr-in-Charge.

Repairing of centrifugal pump of capacity 25.0 HP and transportation to auth / recognised workshop , opening the pump and shaft and separetely carry out the lathe work by metalling to shaft , turning,finishing and polishing complete and replacement of minor part like nuts, bolts and washer deemed to be inclusive in the rate quoted .Removing the existing copper burnt wire, cleaning the slots thoroughly and rewinding the motor of capacity 25.0 HP with supper enameled copper conductor of existing gauge and turns including insulating material like, insulating paper , sleeves and varnishing complete reset the pump and motor with testing on full load to achieve the efficiency of pump .

Supply only motor / pump ball bearing of capacity 25.0 HP pump of existing size all as directed .

Supply and fixing heavy duty iron chain 10 to 20 mm all as directed by Engr-in- Charge.

Material, labour for servicing and testing of DG set of capacity 40 KVA make - Cummins from authorised OEM, complete with replacement of unsv fuel filter, oil filter, draining out old E/ oil and Coolant including cleaning of oil sump and radiator by applying reverse water pressur inside the radiator, radiator inlet/ outlet hose pipes, fan velt complete with the satisfaction of Engr-in- Charge . All connected items such as fuel filter , oil filter , Coolant/ E/Oil , fan velt shall be supply and paid under respective items .

Supply only Fuel Filter

Supply only Lub oil filter

Supply only Radiator Fan belt.

Supply only Radiator hose pipe inlet and outlet with SS adjustable clamp.

Supply only Flexible fuel supply pipe filter to FIP.

Supply only Alternator Fan belt.

Supply only Coolant for DG set.

Supply only Engine oil grade 15w40 as recommanded by OEM.

Material and labour for servicing of DG set of capacity 62.5/82.5 KVA Make - Kirloskar. complete from authorised OEM with replacement of unsv fuel filter, oil filter, draining out old E/ oil and Coolant including cleaning of oil sump and radiator by applying reverse water pressur inside the radiator, radiator inlet/ outlet hose pipes, fan velt complete with the satisfaction of Engr-in- Charge . All connected items such as fuel filter , oil filter , Coolant/ E/Oil , fan velt shall be supply and paid under respective items .

Supply only Fuel Filter

Supply only Lub oil filter

Supply only Radiator Fan belt.

Supply only Radiator hose pipe inlet and outlet with SS adjustable clamp.

Supply only Flexible fuel supply pipe filter to FIP.

Supply only Alternator Fan belt.

Taking out fuel injector pump assembly from DG set of capacity 62.5/82.5 KVA Make- Kirloskar and carrying to the authorised Wk Sp for repair and calibration including replacement of minor part like washer , bolt, gasket as required at site and refixing the same including testing with the satisfaction of Engr-in- Charge.

Taking out self starter 12 Volt from DG set and carrying to the authorised Wk Sp for repair and rewinding including replacement of pinion and teeth ,carbon bush set with holder solenoid switch and minor part like washer , bolt as required at site and refixing the same including testing with the satisfaction of Engr-in- Charge.

Supply and fixing in replacement of copper lead 16 sqmm wire with 1.0 Mtr long wire for battery with brass clamp one end and brass O clamp at other end with nuts and bolts all as directed by Engr-in- Charge.

Supply and fixing in relpacement of battery 12 Volt 100 AH maintenance free.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI strip 32x6mm by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s/ Machinery etc including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.

Supply and fixing in replacement of pressure gauge heavy duty metallic body in sewage treatment plants of range-0 to 14Kg / Sq Cm.

Supply and fix in replcement of sluice valve butterfly type flange end both side heavy duty of size 100mm bore ISI mark complete with nuts, bolts and washer complete all as specified and directed at site.

Supply and fix in replcement of sluice valve butterfly type flange end both side heavy duty of size 80 mm bore ISI mark complete with nuts, bolts and washer complete all as specified and directed at site.

Supply and fix in replcement of butterfly valve type flange end both side heavy duty of size 100 mm bore ISI mark complete with nuts, bolts and washer complete all as specified and directed at site.

Supply and fix in replcement of butterfly valve type flange end both side heavy duty of size 80 mm bore ISI mark complete with nuts, bolts and washer complete all as specified and directed at site.

Supply and fix in replcement of butterfly valve type flange end both side heavy duty of size 65/50 mm bore ISI mark complete with nuts, bolts and washer complete all as specified and directed at site.

Supply and fix in replacement of PAC dosing pump electro magnetic drive less moving parts,Max flow rate 0-6 Ltr / Hrs with pressure 3.5 Kg/Cm2 single phase AC , 230 Volt 50 Hz, Suction lift up to 1.5 mtr water max , flow adjusment o to 100%

Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 50 Sqmm 3.5 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 25 Sqmm 3.5 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 M depth in soft / loose soil and geting out complete all as specified and directed.

Material and labour for sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed.

Material and labour for contineous brick edging with width equal to the depth of the brick of whole sub class 'B' bricks laid on edge complete all as specified and directed.

Supply / laying and fixing 50 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick in soft / loose soil complete all as specified and directed.

Removing surplus excavated materials n.exc. 50 Mtr and depositing where directed at a level n. exc. 1.5 Mtr above the starting point complete all as specified and directed.

Supply and installed in replacement of LED Sensor light fitting 1x 70 Watt luminaries colour temprature 5700 K pressure die cast aluminium housing comprising high power LEDs enclosed with lens embedded PC cover with LED driver complete IP 65 protection. :

S & F in repair,DOL starter model MK1 three phase 415 volt 50 Hz AC, relay range 11-18 (A) suitable for 5 HP electric driven motor at sewage plants.

S & F in repair,fully autometic Star Delta Starter model MU 2 SASD ( with MU relay)Starter three phase 415 volt 50 Hz AC suitable for 25 HP electric driven motor at sewage plants.

S & F in repair, OFF line change over switch with handle 4 pole 415 Volt 50 Hz 200 Amps AC supply complete with dismantling old unsv and all as directed .

S & F in repair, OFF line change over switch with handle 4 pole 415 Volt 50 Hz 100 Amps AC supply complete with dismantling old unsv and all as directed .

S&F in repair heavy duty flexible wire 4 core 4 sqmm 415 volt 50 Hz complete all as directed .

S & F in repair foot valve 100mm dia plastic heavy duty with one end threeded as per sample.

S & F in repair power contactor model MU 2 415 volt 50 Hz three wire suitable for 25 HP motor complete all as directed

S & F in repair PVC heavy duty flexible pipe 100mm dia complete all as directed .As per sample

S & F in repair PVC section heavy duty flexible pipe 80mm dia complete all as directed .As per sample

S & F in repair PVC section heavy duty flexible pipe 65mm dia complete all as directed .As per sample

Material and labour in replacement of air deffusers in STP MBBR/ Equalization / Sludge tanks of size 25mm dia PVC heavy duty tread type complete as per sample or as directed.

Material and labour in replacement of moving bed MBBR filter floating media ring type plain surface area > 80 sqm / cum.

Material and labour charges for cleaning out of sludge holding / to seadler tank after pumping out all fluids and taking out solid sludge deposited inside the tank of plant capacity 200 / 400/500/700 KLD complete all as specified and direcred .

Material and labour charges for cleaning out of equalization tank after pump out all fluids and taking out solid sludge deposited in side the tank by mechanically of plant capacity 200 / 400/500/700 KLD complete with the satisfection of Engr-in- Charge.

Material and labour charges for cleaning out of treated water tank after pump out all water and taking out all solid / sludge deposited in side the tank by mechanical of capacity 200 / 400/500/700 KLD complete with the satisfection of Engr-in- Charge.

Material and labour charges for cleaning out of oil and grease chamber after drainig out all water and taking out of solid / sludge deposited in side the tank by mechanical of capacity 200 / 400/500/700 KLD complete with the satisfection of Engr-in- Charge.

Material and labour charges for cleaning out of MBBR tank after drainig out all water and taking out of solid / sludge deposited in side the tank segregate the MBBR media tank of capacity 200 / 400/500/700 KLD complete with the satisfection of Engr-in- Charge.

Supply and fix in repair preventer single phase 240 volts complete all as specified and directed.

M/S uneversal agency (BID ID -3471071)

CHOUDHARY ELECTRICAL (BID ID -3464537)