Special repair to Bdy wall at filteration plant and other sanctioned work at fazilka mil stn.

Amount

Cutting holes not exc. half brick in brick walls built in CM or cement lime mortar & stone walls built in lime mortar for inserting holdfasts & making good dismantled portion in CM(1:3) or PCC(1:2:4) Type B-1 as required

Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc.

Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in lime or mud mortar; not previously plastered; and scrubbing down with water etc. to receive plaster

Demolition of cement concrete ( un re-inforced) of any description in roofs, floors(other than ground floors), beams, staircases, landing, chajjas and similar suspended work all as specified.

M&L PCC type B1 (1:2:4) using 20 mm agrregate in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts complete all as directed by Engineer in charge

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

M&L Washed stone grit plaster coloured/pigmented type on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 pigmented stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using alluminium channel, nailed to the under layer panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces , complete all as specified and directed.

M&L applying two coats of synthetic enamel paint including preparation of new steel preprimed surfsce or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M & L for complete removal of existing treatment with hand electric grinder and preparation of old decorated (plastered or unplastered) of walls and applying two coats of cement base paint complete all as specified.

M & L applying two coat of cement base paint on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in – Charge.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing comple

M & L RCC 1:1½:3, (nominal mix), Type A-1, using 20mm graded aggregates as in chajjas, fins, fascias,shelves , louvers, parapets and railing etc and the like including necessary formworks all as specified and directed by Engineer - in - Charge.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

Welding in repairs n. exc 2.5cm in length and thickness of welding n.exe 6mm complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

S&F concertina coil 600mm dia 10mtr openable length having 50nos round per 6mtr length over wall with existing Y shaped angle iron tied with necessary bolts, dia of wire 2.5mm, blade thk 0.5mm, blade length 12mm, width 15mm and spacing 26mm complete all specified

S & F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. (each line wire to be measured)

Takig out & Refixing Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. (each line wire to be measured)

M & L for two coats of synthetic enamel paint over & including a coat of red oxide primer over new steel & iron surfaces of any description, exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed

S & F Mild steel work swan neck, angle iron & flat iron including embedding in concrete and screwing etc, including cutting tops to shape as directed, bent to shape, drilling holes, notching for wire etc, Including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F mild steel screw bolts 16 to 20mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 15cm and n exc 22.5cm long complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed

S & F framed work such as grills, cooler stand ,grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290.Gde-E-165 all as specified .

M & L brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radious built in CM 1:6 all as specified.

M & L rendering 15mm thick on fair faces or other than fair faces of brick work in CM 1:6 finished even & smooth without using extra cement all as specified .

M L providing cement concrete 1 :2 :4 type B1 using 20mm graded stone aggregates as in lintels upto 1.5 m clear span cills , seismic and other similar bands, plinth courses, string courses lacing courses, parapets and railing up to 60 cm in height, copings, kneelers, apex stones bed plates kerbs and water troughs including weathering, slightly rounded or chamfered angles as directed.

M&L for preparation of steel surfaces of any description n. exc. 10cm in width or girth not otherwise described, and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, all as specified and directed by Engr - in - Charge.

Excavation in post holes each n. exc. 0.50Cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. Or for shafts, wells, cesspits, manholes, pier holes, etc. N exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil

M & L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft and loose soil.

Spreading and levelling in layers n exc. 25 cm thick including well ramming and watering.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation of cols, bdy pillars, posts, struts, etc. filling and mass concrete complete all as specified and shown on drawing.

M & L for 75mm thick cement concrete type D-2 (1:4:8) using 40mm graded stone aggregate as in sub floors, sub bases etc all as specified and directed by Engineer - in - Charge.

S&F machine pressed precast concrete interlocking paver block with grey cement & pigment, any shape and size confirming to IS 15658-2006 of 60 mm thick M-40 grade including and over 25mm thick sand cushion.

S&F Structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes grade St-240 complete all as specified and as shown on drawing.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L for 75mm thick cement concrete type C2 1:3:6 (40mm graded aggregate) as in plinth protection , surface finished even and smooth without using extra cement .

RUCHIKA CONSTRUCTIONS

KATARIA CONSTRUCTION

SILEWAL CONTRACTOR & SUPPLIER

BHARAT BHUSHAN CONTRACTOR

M/s Vikas Kumar Doda Contractor