NIT No:- TC/UAD/2026/.. Raipur, Dated:- 24.07.26

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

1 1.1 Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto 1.5 m lift and lead upto 50m (at least 5m away from the dressed area). 797.44 Cum

2 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 843.62 Cum

3 1.6 Extra for every additional lift of 1.5 m or part thereof.

1.6.1 All types of soils 421.81 Cum

4 1.17 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M. 574.62 cum

5 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete. 325.21 cum

6 3.1 Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of form work.

3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). 109.32 Cum

7 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size). 311.09 cum

8 3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 233.19 Cum

9 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.1 Thermo-Mechanically treated bars FE 415 65314.04 kg

10 3.13 Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including form work. 4.17 cum

11 3.16 Making 50mm thick plinth protection of plain cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with sand including finishing the top smooth. 96.57 sqm

12 2.1 Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

12.1 2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level. 756.44 Sqm

12.2 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 107.60 Sqm

12.3 2.1.6 Columns, beams & walls- circular or any other geometrical shape other than square and rectangular in all sizes 217.41 Sqm

12.4 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ) 668.87 Sqm

12.5 2.1.8 Beams, lintels, cantilevers & walls 616.99 Sqm

12.6 2.1.15 Stair cases of all types excluding spiral and folded plate type, including risers and landings 71.32 sqm

13 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand) 22.22 cum

14 7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 80.95 Cum

15 7.11 Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level

7.11.2 Cement Mortar 1:4 (1 cement : 4 coarse sand) 39.26 sqm

16 7.20 Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry. 39.26 sqm

17 8.4 Providing and fixing Dash fastener (for fixing door/ window frames) on C.C. / R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.

8.4.3 Dash fastener 12x100mm 45.00 each

18 8.16 Providing and fixing PVC membrane foil coated (laminated) flush door shutters, made with core of block board with frame of first class hard wood, coated with 0.30mm membrane pasted with resin using vacuam treatment process complete all but excluding hinges.

8.16.1 35 mm thick (single leaf) 14.16 sqm

19 8.15 Extra for double leaf shutter instead of single leaf. 2.88 sqm

20 8.58 Providing and fixing bright finished brass butt hinges with brass polished MS screws complete:

8.58.1 125x85x5.50 mm (Heavy Type) 45.00 each

21 8.60 Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete:

22 8.61 Providing and fixing brass door latch with brass polished MS screws complete:

23 8.62 Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:

24 8.86 Providing and fixing 100mm antique/ SS finished brass mortise latch and lock with six levers and a pair of lever handles with antique/ SS polished MS screw complete. 6.00 each

25 8.141 Providing and fixing Stainless steel "D" shape door handles made of 10mm dia rod with necessary stainless steel screws etc complete.

26 8.154 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 12.60 sqm

27 8.158 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 7.00 each

28 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer. 3919.00 kg

29 9.47 Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately:

29.1 9.47.1 For fixed portion 1422.22 kg

29.2 9.47.2 For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately). 25.65 Kg

30 9.49 Extra for polyester powder coated (minimum 50 micron) aluminium sections instead of anodized. 1447.87 Kg

31 9.51 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item):

9.51.2 With float glass panes of 5 mm thickness 3.42 sqm

32 9.58 Extra for providing and fixing tinted glass panes in aluminium door, window, ventilator shutters and partitions instead of float glass.

9.58.2 5 mm thickness 3.42 sqm

33 9.57 Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete.

9.57.2 SS Grade 304 175.88 kg

34 9.63 Providing and fixing clear float toughened glass door or partition in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignment with all labour tools and tackles etc complete. (Patch fittings and hardware to be paid for separately).

9.63.1 12 mm thick for door/partition 10.56 sqm

9.63.3 6 mm thick for glazing etc. 161.17 sqm

35 9.64 Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete.

1. Top patch with pivot SS grade 304 20.00 Nos.

2. Top/side patch glass or L-connector patch SS grade-304 40.00 Nos.

3. Bottom patch to be connected with floor machine 20.00 Nos.

4. Bottom lock patch with three key SS grade 304 20.00 Nos.

5. Corner patch fitting with pivot SS grade 304 20.00 Nos.

6. Two way action Hydraulic floor spring machine heavy duty double cylinder type Capacity 120/150 kg mounted on floor including required cutting on floor and proper grouting with rich cement mortar. 2.00 Nos.

7. H type handle 32x600mm SS 304 grade 4.00 Nos.

8. Floor/Wall to Glass Connector SS grade 304 40.00 Nos.

36 10.61 Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting. 69.23 sqm

37 10.67 Providing and fixing Acoustical Suspended Ceiling System made of tiles of size 595x595mm and specified thickness as approved by Engineer-In-Charge, in tru Horizontal Level Suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanised @120 gsm both side inclusive) consisting of main "T" Runner with suitably spaced joints to get required lenght and of size 24x38 mm made from 0.30 thick(minimum ) sheet, spaced at 1200mm center to center and cross "T" of size 24x38mm made of 0.30 thick (minimum) sheet, 1200 mm long spaced between main "T" at 600mm center to lenght 600 mm and size 24x38mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24mm and laying false ceiling tiles of approved texture in the grid, cutting/ making opening for services like diffusers, grills light fitting, fixtures, smoke detectors etc wherever required. Main "T" runner to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5mm dia and 50mm long

dash fasteners, 4mm dia GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center ot center along main "T". Bottom exposed width of 24mm of all "T" sections shall be pre-painted with polyster paint, all complete for all heights as per specification drawings or as directed by Enginner-In-Charge. The tiles should have Humidity resistance (RH) of 99%, Light Reflectance>83%, Thermal Conductivity K=0.052-0.57 w/mk, color white, fire performance UKclass0/Class1(BS476pt-6and7) in module size of 600x600x16 mm with Bio Block coating on the face of the tile, suitable for green building application, with recycled content of 38-41%. Cielinng height up 3.5 mt from adjacent floor level. Extra height to be paid serately.

10.67.2 With 20 mm thick bevelled/tegular edged mineral fibre false ceiling tile (NRC 0.7) 584.65 sqm

38 10.71 amendment Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595 mm, having NRC(Noise Reuction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85%(minimum). Non combustible as per BS:476(part-4), fire performance as per BS:476(part 6&7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, comprising of a frame made from especially fabricated galvanised mild steel steel sheet 0.50 mm thick pressed section (galvanizing @ 120 grams per sqm incluidng both sides) i.e. vertical studs of size 48 x 34 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50x32 m fixed to the floor and soffit at 600 mm centers using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 500mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer's specifiaction as per direction of Engineer-In-Charge all complete.

Wall Panaling Work 652.43 sqm

39 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand) 654.91 sqm

40 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 880.06 sqm

41 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 443.99 sqm

42 11.9 Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer. 44.40 kg

43 12.45 15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above)

12.45.3 Granite stone lakha red/ shahi red 702.90 sqm

44 12.46 15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m).

12.46.3 Granite stone lakha red/ shahi red 76.97 sqm

45 12.44 Extra for nosing in Granite stone for treads. 96.74 metre

46 12.74 Providing and fixing rectified glazed ceramic Floor tiles of 1st quality conforming to IS : 15622-2017 of approved make, in all colours, shades over 20 mm thick bed of cement Mortar 1:3 (1 cement:3 coarse sand ) and jointing with grey cement sluryy @ 3.3 kg per sqm including pointing in white cement mixed with matching pigment complete.

12.74.3 Size 600x600mm thickness 8 to 9mm 50.24 sqm

47 12.75 Providing and fixing recified glazed ceramic wall/dado tiles of 1st quality conforming to IS:15622-2017 of approved make, in all colors, shades on wall and dados over 12 mm thick bed of cement Mortar 1:3(1 cement:3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

12.75.2 Size 300x600mm thickness 7 to 8mm 209.14 sqm

48 13.6 15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish.

13.6.2 Granite stone black 82.43 sqm

49 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 880.06 Sqm

50 14.57 Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied @ 4.0 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Asian trucare, Berger Happy walls Putty Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work . (This Item to be use in heigher grade painting works Item No. 14.65) 1534.97 Sqm

51 14.65 Providing and applying Luxury plastic enmulsion paint with roller application minimum three Coats applied @ 1.25 lit / 10Sqm up to final finish as per relevant Type - 1 Class D, C, B & A (Glossy /Semi Glossy and Matt , Egg Shell or Satin finish ) of required shade (Product such as Asian Royale Shyne,Dulux Velvet Touch, Berger Silk Luxury Emulsion ,Nippon Impression Pearl, Opus Pure Elegance) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc, complete for the work. (with 4 Years Warranty ) 347.41 sqm

52 14.69 Providing and applying exterior surface with PREMIUM HEAVY DUTY Glossy or Matt Finish Exterior Emulsion paint of required shade to give protective and water proof finish minimum three coats applied @ 143 lit/ 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D,C,B & A (Glossy / matt / Egg Shell finish )having high DFT and silicon aditive for elastomaric property (Product such as Asian Ultima Dulux Weathershield Maxx , Berger Weathercoat All Guard Nerolac Excel Total , Nippon Durafresh Expert, Opus Tru Look) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. (With 4 Year Warranty) 443.99 sqm

53 14.72 Providing and applying Glossy finish Enamel paint mimimum 2 Coats in al surface applying @ 0.75 lit/ 10 Sqm up to required finish as per relevent I.S. code 2932: 2013 of (Product such as Asian Apcolite Premium Enamel Dulux Promise Premium Enamel Nerolac Synthatic Enamel, Opus Prime enamel ) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackle and labour etc. complete for the work. 156.76 sqm

54 24.23 Ele. Sor 2020 Supplying, installation, testing and commissiong of following size drinking water cooler storage type ISI marked, eco friendly non CFC refrigarant, water tank and cooler cabinet sheet material- stainless steel {grade AISI 304} with thickness>= 0.8 mm, with PUF insulation including all accessories connection etc complete as per specification.

24.23.3 150/300 Ltrs/hr 1.00 Each

55 24.24 Ele. Sor 2020 Supplying, installation, testing and commissiong of following capacity of RO purification system with UF/UV/TDS controler and UV lamp {IS 14724 Ultra voilet disinfection} and minimum three stage purification, automatic on/off, output water conferming standard IS 10500 with inbuild storage tank including all accessories connection etc complete as per specification.

24.24.2 50 Ltrs/hr output capacity 1.00 Each

Ground Floor Electrification Work

Ground Floor Plumbing Work of

Ground Floor Firefighting Work

Total (A+B+C+D)

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

GROUND FLOOR ELECTRICAL WORK

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

Sub Head 1 : Point Wiring

1 1.7 Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Liqhtpoints / Ex Fan points

1.1 1.7.1 Short Point 20 Point

1.2 1.7.2 Medium Point 50 Point

1.3 1.7.3 Long Point 35 Point

Twin control liqht point

2 1.8 Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 8 Point

3 1.9 Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 20 Point

4 1.11 Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

4.1 1.11.3 Long Point 5 Point

4.2 1.11.4 Extra Long Point I 15 Point

4.3 1.11.5 Extra Long Point II 10 Point

4.4 1.11.6 Extra Long Point III 10 Point

Sub Main in Concealed PVC Conduit

5 1.13 Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

5.1 1.13.1 3 X 1.5 sq. mm in 20mm conduit 549.87 Metre

5.2 1.13.2 3 X 2.5 sq. mm in 20mm conduit 155 Metre

5.3 1.13.3 6 X 2.5 sq. mm in 25mm conduit 200 Metre

5.4 1.13.4 9 X 2.5 sq. mm in 32mm conduit 100 Metre

5.5 1.13.6 3 X 4 sq. mm in 25mm conduit 100 Metre

5.6 1.13.7 3 X 6 sq. mm in 25mm conduit 20 Metre

6 3.12 Supplying and drawing following pair 0.5 mm FR PVC insulated copper conductor, unarmored telephone wire in the existing surface/ concealed Steel/FRLS PVC conduit as per specification

3.12.2 2 Pair 100 Metre

7 3.14 Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification 120 metre

8 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

9 4.4 Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

9.1 4.4.2 100mmX75mm (3 Module) 7 Each

9.2 4.4.4 200mmX75mm (6 Module) 5 Each

10 4.5 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

10.1 4.5.3 3 Module 2 Each

10.2 4.5.5 6 Module 2 Each

11 5.4 Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.

11.1 5.4.1 5/6 amps one way switch 30 Each

11.2 5.4.4 15/16 amp switch 15 Each

11.3 5.4.5 3 pin 5/6 amp socket outlet 15 Each

11.4 5.4.6 6 pin 15/16 amp socket outlet 15 Each

11.5 5.4.9 Fan regulator (two module size) electronic stepped type moving all rounds 30 Each

11.6 5.4.15 Telephone socket outlet 5 Each

11.7 5.4.17 Computer Outlet Jack 10 Each

11.8 5.4.20 Ceiling rose 3 pin 5 amp 10 Each

12 5.6 Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification. 10 Each

Sub Head 2 : Accessories, Luminaires and Fans

12 6.71 Supplying , installation , testing and commissioning of following recess mounted DALI/0-10volt Analogue dimmable LED/COB Downlighter with Die cast housing made of aluminum and white. Powder coated finish. Diming should be Based LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000-6000K CCT with minimum life cycle 50000 hrs burning hours at 50˚C. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%.

13 6.88 Supplying , installation , testing and commissioning for the following LED RGB / RGBW Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . Luminaire shall be capable of producing dynamic color changing light with 16 million colors by DMX / Ethernet based control . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor >0.9 . Fixture shall be suitable to operate at ambient temperature range of -10 Degree C to +50 Degree C and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required.

6.88.2 35-40 watt 10 Each

14 6.16 Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.

6.16.2 36 watt, size 600 x 600mm 65 Each

15 6.18.5 Supplying, installation, testing and commissioning of following COB LED Spot Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 10 Each

16 6.26 Supplying, installation, testing and commissioning of following LED Signage entry/exit having minimum size 300mm (L) x 200mm (H) x 45mm (W), fitting complete including built in battery backup for 2 hour with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-20,6.26.2- Double sided LED Signage 10 Each

ITC fluorescent fitting with down rods:

17 6.4 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification. 40 Each

18 6.6 Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9

6.6.1 300 mm sweep 10 Each

19 5.9 Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as per specification. 15 Each

Sub Head 3 : Switchboards

20 9.4 Supplying and fixing on surface/ recess horizontal type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator)

20.1 9.4.4 4 way Double door 1 Each

20.2 9.4.5 6 way Double door 2 Each

20.3 9.4.6 8 way Double door 2 Each

21 9.11 Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.11.2 6 amps to 32 amps 96 Each

22 9.20 Supplying and fixing following rating, 415 volts, FOUR POLES, ISOLATOR in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.20.1 40 amps 2 Each

9.20.2 63 amps 2 Each

23 9.22 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.22.2 40 amps 2 Each

9.22.3 63 amps 2 Each

Sub Head 4 : Earthing

24 12.19 Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification:

12.19.1 With 3 metre long GI Pipes and 50 kg back filling compound. 2 Each

25 12.13 Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification. 20 Metre

26 12.17 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as per specification. 250 Metre

Sub Head 5 : Cable and cable management

27 15.3 Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

28 15.5 Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as required.

15.5.13 4 x 10 sq. mm. 120 Metre

15.5.14 4 x 16 sq. mm. 85 Metre

15.5.15 4 x 25 sq. mm. 20 Metre

29 15.13 Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010).

15.13.3 6 x 1.5 sq. mm 80 Metre

30 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

1.15.2 25 mm 70 Metre

1.15.3 32 mm 70 Metre

14.1 Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.

14.1.1 63 mm outer dia 35 Metre

BRASS COMPRESSION GLAND

31 15.24 Supplying and making end termination with brass compression gland and copper lugs for following size armoured copper conductor power cable of 1.1 KV grade as per specification.

a) 15.24.1 2 X 4 sq. mm (16 mm) 5 Each

32 18.1 Supplying and installing following size powder coated, perforated M.S. cable trays with perforation not more than 17.5% rigidly suspended from the ceiling with M.S. suspenders at a distance not more than 2.5 metre and near every junction/ joint etc complete as per specification.

18.1.2 150 mm width X 50 mm depth X 1.6 mm thickness 104.8585 Metre

33 7.19 Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured)

7.19.1 Upto 300 mm deep 2 sqm

34 7.20 Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification.

7.20.3 300 amp (50x5mm) 5 Metre

35 9.1 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.

9.1.6 3 pole MCCB, 160A, Adjustable Thermal - Magnetic Release, 25KA 1 Each

36 9.16 Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.16.3 40 amps 5 Each

9.16.5 63 amps 5 Each

37 10.9 Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification.

10.9.2 160 amps 1 Each

38 10.15 Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.15.3 200/5 amps 2 Each

39 10.17 Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification. 2 Each

40 10.20 Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.20.2 Digital type 1 Each

41 10.18 Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.18.3 0-200 amps 1 Each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

GROUND FLOOR SANITATION & WATER SUPPLY WORK

1 18.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.1.3 White Orissa pattern W.C. pan of size 580x440 mm 10.00 each

2 18.4 Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.4.3 White wall hung type 10.00 each

3 18.13 Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete:

18.13.2 Flat back type urinal of size 460x380x250mm

Urinal 15.00 each

4 18.17 Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

18.17.5 White Oval or round size 550x400mm.

Wash Basin 8.00 each

5 18.25 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Kitchen sink & wash basins 8.00 each

6 18.26 Providing and fixing PVC waste coupling in wash basin/ sink.

Kitchen sink & wash basins 8.00 each

7 18.76 Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete.

18.76.2 110 mm dia pipe. 400 meter

18.76.3 150 mm dia pipe. 500 meter

8 18.77 Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

8.1 18.77.1 Tee/ Tee with door/ Bend 45°/ Bend 90°

8.4 18.77.6 Nahani trap 110x75mm 30.00 each

9 19.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

9.1 19.6.1 15 mm nominal outer dia pipes 166 meter

9.2 19.6.1 20 mm nominal outer dia pipes 200 meter

9.3 19.6.3 25 mm nominal outer dia pipes 250 meter

9.4 19.6.4 32 mm nominal outer dia pipes 160 meter

9.5 19.6.5 40 mm nominal outer dia pipes 150 meter

9.6 19.6.5 50 mm nominal outer dia pipes 300 meter

10 19.14 Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:

10.1 19.14.2 Long nose bib cock (500 grams) 35.00 each

10.2 19.14.6 Stop cock (concealed) (600 grams) 35.00 each

10.3 19.14.9 Kitchen sink mixer with cast swivel spout (1000 grams) 1.00 each

10.4 19.14.10 Wall mixer with elegant knob (1400 grams) 10.00 each

10.5 19.14.15 Shower rose (revolving type) (150mm) 10.00 each

11 19.15 Providing and fixing stainless steel drain jali of approved make/quality. 50.00 each

12 19.16 Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end):

12.1 19.16.1 25 mm nominal bore 15.00 each

12.2 19.16.4 32 mm nominal bore 10.00 each

12.3 19.16.5 40 mm nominal bore 15.00 each

13 20.29 Providing and constructing brick masonry chamber for underground pipe and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) RCC cover of suitable size and 75mm thick with 1:1.5:3 mix (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including reinforcement 8mm dia bars at 150mm both ways and MS hooks for lifting, including foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

13.1 20.29.1 Inside dimensions 450x600 mm and 45 cm deep for single pipe line : 10.00 each

13.2 20.29.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : 10.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

GF FIRE FITING WORK

BUILDING SOR 2015

1 23.1 Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line.

2 23.2 Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.

3 23.5 Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required..

23.5.1 80 mm dia 10.00 each

4 23.7 Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified.

5 23.7.2 50 mm dia 10.00 each

6 23.13 Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required. 220.00 each

7 23.14 Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

HOSE REEL DRUM 5.00 each

8 23.18 Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

HYDRANT VALVE 5.00 each

9 23.22 Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

RRL hose pipe 5.00 each

10 23.24 Supplying & fixing 63 mm dia Stainless Steel IS: 3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzle conforming to IS: 903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

branch pipe 5.00 each

11 23.25 Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required.

23.25.2 Size 900 mm x 600 mm x 500 mm 5.00 each

ELECTRICAL SOR 2020

12 26.17 Supply and erecting of following ISI marked Fire extenguishers on wall/ column including erecting bracket etc complete.

12.1 26.17.5 CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve 5.00 each

12.2 26.17.3 ABC Fire Extinguisher 4KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 2A, 89B. With all accessories. 5.00 each

13 26.1 Suppying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 50 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes, 1.00 each

14 26.9 Suppying , installation , testing and commissioning of Intelligent Addressable Multi-sensor Smoke detector: Multi-criteria addressable fire detector that incorporates photoelectric and thermal sensors,Polarity insensitive utilizing SureWireTM technology,Tri-color detector status LED with 360° viewing,Field-selectable application profiles,Superior EMI immunity, Remote sensitivity-measurement capability,Automatic environment compensation,UL Listed and ULC Listed; FM Approved. 240.00 each

15 26.11 Suppying , installation , testing and commissioning of Intelligent Addressable Type Manual Call Point: Intelligent Manual Fire Alarm Box is constructed of durable, molded and polycarbonate material that is matte finished in red with raised white lettering Single-action,Pull-down lever is down, until manually reset,Polarity insensitive via SureWireTM technology 30.00 each

16 26.13 Suppying , installation , testing and commissioning of Conventional Type Hooter with Strobe: Hooter with Strobe. Wall Mount models feature field selectable candela settings of 15/30/75/110cd and 135/185cd. Ceiling Mount models feature field selectable candela settings of 15/30/75/95cd and 115/177cd. UL Listed, ULC, FM approved. NFPA Compliant. Red. 22.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

1 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 230.12 Cum

2 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.1 Thermo-Mechanically treated bars FE 415 27614.53 kg

3 2.1 Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

3.1 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 107.60 Sqm

3.2 2.1.6 Columns, beams & walls- circular or any other geometrical shape other than square and rectangular in all sizes 217.41 Sqm

3.3 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ) 649.50 Sqm

3.4 2.1.8 Beams, lintels, cantilevers & walls 601.31 Sqm

3.5 2.1.15 Stair cases of all types excluding spiral and folded plate type, including risers and landings 44.45 sqm

4 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 58.63 Cum

5 7.11 Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level

7.11.2 Cement Mortar 1:4 (1 cement : 4 coarse sand) 39.26 sqm

6 7.20 Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry. 39.26 sqm

7 8.4 Providing and fixing Dash fastener (for fixing door/ window frames) on C.C. / R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.

8.4.3 Dash fastener 12x100mm 33.00 each

8 8.16 Providing and fixing PVC membrane foil coated (laminated) flush door shutters, made with core of block board with frame of first class hard wood, coated with 0.30mm membrane pasted with resin using vacuam treatment process complete all but excluding hinges.

8.16.1 35 mm thick (single leaf) 11.28 sqm

9 8.58 Providing and fixing bright finished brass butt hinges with brass polished MS screws complete:

8.58.1 125x85x5.50 mm (Heavy Type) 33.00 each

10 8.60 Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete:

11 8.61 Providing and fixing brass door latch with brass polished MS screws complete:

12 8.62 Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:

13 8.86 Providing and fixing 100mm antique/ SS finished brass mortise latch and lock with six levers and a pair of lever handles with antique/ SS polished MS screw complete. 4.00 each

14 8.141 Providing and fixing Stainless steel "D" shape door handles made of 10mm dia rod with necessary stainless steel screws etc complete.

15 8.154 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 11.03 sqm

16 8.158 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 4.00 each

17 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer. 4121.02 kg

18 9.47 Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately:

18.1 9.47.1 For fixed portion 1490.91 kg

18.2 9.47.2 For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately). 22.95 Kg

19 9.49 Extra for polyester powder coated (minimum 50 micron) aluminium sections instead of anodized. 1513.86 Kg

20 9.51 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item):

9.51.2 With float glass panes of 5 mm thickness 3.06 sqm

21 9.58 Extra for providing and fixing tinted glass panes in aluminium door, window, ventilator shutters and partitions instead of float glass.

9.58.2 5 mm thickness 3.06 sqm

22 9.57 Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete.

9.57.2 SS Grade 304 1183.35 kg

23 9.63 Providing and fixing clear float toughened glass door or partition in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignment with all labour tools and tackles etc complete. (Patch fittings and hardware to be paid for separately).

9.63.1 12 mm thick for door/partition 10.56 sqm

9.63.3 6 mm thick for glazing etc. 169.61 sqm

24 9.64 Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete.

1. Top patch with pivot SS grade 304 20.00 Nos.

2. Top/side patch glass or L-connector patch SS grade-304 40.00 Nos.

3. Bottom patch to be connected with floor machine 20.00 Nos.

4. Bottom lock patch with three key SS grade 304 20.00 Nos.

5. Corner patch fitting with pivot SS grade 304 20.00 Nos.

6. Two way action Hydraulic floor spring machine heavy duty double cylinder type Capacity 120/150 kg mounted on floor including required cutting on floor and proper grouting with rich cement mortar. 2.00 Nos.

7. H type handle 32x600mm SS 304 grade 4.00 Nos.

8. Floor/Wall to Glass Connector SS grade 304 40.00 Nos.

25 10.61 Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting. 65.58 sqm

26 10.67 Providing and fixing Acoustical Suspended Ceiling System made of tiles of size 595x595mm and specified thickness as approved by Engineer-In-Charge, in tru Horizontal Level Suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanised @120 gsm both side inclusive) consisting of main "T" Runner with suitably spaced joints to get required lenght and of size 24x38 mm made from 0.30 thick(minimum ) sheet, spaced at 1200mm center to center and cross "T" of size 24x38mm made of 0.30 thick (minimum) sheet, 1200 mm long spaced between main "T" at 600mm center to lenght 600 mm and size 24x38mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24mm and laying false ceiling tiles of approved texture in the grid, cutting/ making opening for services like diffusers, grills light fitting, fixtures, smoke detectors etc wherever required. Main "T" runner to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5mm dia and 50mm long

dash fasteners, 4mm dia GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center ot center along main "T". Bottom exposed width of 24mm of all "T" sections shall be pre-painted with polyster paint, all complete for all heights as per specification drawings or as directed by Enginner-In-Charge. The tiles should have Humidity resistance (RH) of 99%, Light Reflectance>83%, Thermal Conductivity K=0.052-0.57 w/mk, color white, fire performance UKclass0/Class1(BS476pt-6and7) in module size of 600x600x16 mm with Bio Block coating on the face of the tile, suitable for green building application, with recycled content of 38-41%. Cielinng height up 3.5 mt from adjacent floor level. Extra height to be paid serately.

10.67.2 With 20 mm thick bevelled/tegular edged mineral fibre false ceiling tile (NRC 0.7) 602.55 sqm

27 10.71 amendment Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595 mm, having NRC(Noise Reuction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85%(minimum). Non combustible as per BS:476(part-4), fire performance as per BS:476(part 6&7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, comprising of a frame made from especially fabricated galvanised mild steel steel sheet 0.50 mm thick pressed section (galvanizing @ 120 grams per sqm incluidng both sides) i.e. vertical studs of size 48 x 34 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50x32 m fixed to the floor and soffit at 600 mm centers using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 500mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer's specifiaction as per direction of Engineer-In-Charge all complete.

Wall Panaling Work 458.34 sqm

28 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand) 641.24 sqm

29 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 640.18 sqm

30 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 366.30 sqm

31 11.9 Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer. 36.63 kg

32 12.45 15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above)

12.45.3 Granite stone lakha red/ shahi red 815.01 sqm

33 12.46 15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m).

12.46.3 Granite stone lakha red/ shahi red 48.58 sqm

34 12.44 Extra for nosing in Granite stone for treads. 67.20 metre

35 12.74 Providing and fixing rectified glazed ceramic Floor tiles of 1st quality conforming to IS : 15622-2017 of approved make, in all colours, shades over 20 mm thick bed of cement Mortar 1:3 (1 cement:3 coarse sand ) and jointing with grey cement sluryy @ 3.3 kg per sqm including pointing in white cement mixed with matching pigment complete.

12.74.3 Size 600x600mm thickness 8 to 9mm 46.92 sqm

36 12.75 Providing and fixing recified glazed ceramic wall/dado tiles of 1st quality conforming to IS:15622-2017 of approved make, in all colors, shades on wall and dados over 12 mm thick bed of cement Mortar 1:3(1 cement:3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

12.75.2 Size 300x600mm thickness 7 to 8mm 191.73 sqm

37 13.6 15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish.

13.6.2 Granite stone black 80.48 sqm

38 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 366.30 Sqm

39 14.57 Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied @ 4.0 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Asian trucare, Berger Happy walls Putty Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work . (This Item to be use in heigher grade painting works Item No. 14.65) 1281.42 Sqm

40 14.65 Providing and applying Luxury plastic enmulsion paint with roller application minimum three Coats applied @ 1.25 lit / 10Sqm up to final finish as per relevant Type - 1 Class D, C, B & A (Glossy /Semi Glossy and Matt , Egg Shell or Satin finish ) of required shade (Product such as Asian Royale Shyne,Dulux Velvet Touch, Berger Silk Luxury Emulsion ,Nippon Impression Pearl, Opus Pure Elegance) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc, complete for the work. (with 4 Years Warranty ) 257.36 sqm

41 14.69 Providing and applying exterior surface with PREMIUM HEAVY DUTY Glossy or Matt Finish Exterior Emulsion paint of required shade to give protective and water proof finish minimum three coats applied @ 143 lit/ 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D,C,B & A (Glossy / matt / Egg Shell finish )having high DFT and silicon aditive for elastomaric property (Product such as Asian Ultima Dulux Weathershield Maxx , Berger Weathercoat All Guard Nerolac Excel Total , Nippon Durafresh Expert, Opus Tru Look) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. (With 4 Year Warranty) 366.30 sqm

42 14.72 Providing and applying Glossy finish Enamel paint mimimum 2 Coats in al surface applying @ 0.75 lit/ 10 Sqm up to required finish as per relevent I.S. code 2932: 2013 of (Product such as Asian Apcolite Premium Enamel Dulux Promise Premium Enamel Nerolac Synthatic Enamel, Opus Prime enamel ) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackle and labour etc. complete for the work. 164.84 sqm

43 24.23 Ele. Sor 2020 Supplying, installation, testing and commissiong of following size drinking water cooler storage type ISI marked, eco friendly non CFC refrigarant, water tank and cooler cabinet sheet material- stainless steel {grade AISI 304} with thickness>= 0.8 mm, with PUF insulation including all accessories connection etc complete as per specification.

24.23.3 150/300 Ltrs/hr 1.00 Each

44 24.24 Ele. Sor 2020 Supplying, installation, testing and commissiong of following capacity of RO purification system with UF/UV/TDS controler and UV lamp {IS 14724 Ultra voilet disinfection} and minimum three stage purification, automatic on/off, output water conferming standard IS 10500 with inbuild storage tank including all accessories connection etc complete as per specification.

24.24.2 50 Ltrs/hr output capacity 1.00 Each

First Floor Electrification Work

First Floor Plumbing Work of

First Floor Firefighting Work

Total (A+B+C+D)

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

FIRST FLOOR ELECTRICAL WORK

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

Sub Head 1 : Point Wiring

1 1.7 Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Liqhtpoints / Ex Fan points

1.1 1.7.1 Short Point 15 Point 266.00 3,990.00

1.2 1.7.2 Medium Point 40 Point 424.00 16,960.00

1.3 1.7.3 Long Point 30 Point 588.00 17,640.00

Twin control liqht point

2 1.8 Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 5 Point 420.00 2,100.00

3 1.9 Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 15 Point 216.00 3,240.00

4 1.11 Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

4.1 1.11.3 Long Point 3 Point 1350.00 4,050.00

4.2 1.11.4 Extra Long Point I 10 Point 1807.00 18,070.00

4.3 1.11.5 Extra Long Point II 8 Point 2315.00 18,520.00

4.4 1.11.6 Extra Long Point III 8 Point 2825.00 22,600.00

Sub Main in Concealed PVC Conduit

5 1.13 Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

5.1 1.13.1 3 X 1.5 sq. mm in 20mm conduit 350 Metre 92.00 32,200.00

5.2 1.13.2 3 X 2.5 sq. mm in 20mm conduit 100 Metre 111.00 11,100.00

5.3 1.13.3 6 X 2.5 sq. mm in 25mm conduit 120 Metre 172.00 20,640.00

5.4 1.13.4 9 X 2.5 sq. mm in 32mm conduit 65 Metre 238.00 15,470.00

5.5 1.13.6 3 X 4 sq. mm in 25mm conduit 65 Metre 145.00 9,425.00

5.6 1.13.7 3 X 6 sq. mm in 25mm conduit 8 Metre 182.00 1,456.00

6 3.12 Supplying and drawing following pair 0.5 mm FR PVC insulated copper conductor, unarmored telephone wire in the existing surface/ concealed Steel/FRLS PVC conduit as per specification

7 3.14 Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification 100 metre 19.00 1,900.00

8 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

9 4.4 Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

10 4.5 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

11 5.4 Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.

11.1 5.4.1 5/6 amps one way switch 20 Each 69.00 1,380.00

11.3 5.4.5 3 pin 5/6 amp socket outlet 10 Each 96.00 960.00

11.4 5.4.6 6 pin 15/16 amp socket outlet 10 Each 120.00 1,200.00

11.5 5.4.9 Fan regulator (two module size) electronic stepped type moving all rounds 20 Each 223.00 4,460.00

11.6 5.4.15 Telephone socket outlet 5 Each 70.00 350.00

11.7 5.4.17 Computer Outlet Jack 10 Each 242.00 2,420.00

11.8 5.4.20 Ceiling rose 3 pin 5 amp 10 Each 40.00 400.00

12 5.6 Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification. 8 Each 816.00 6,528.00

Sub Head 2 : Accessories, Luminaires and Fans

12 6.71 Supplying , installation , testing and commissioning of following recess mounted DALI/0-10volt Analogue dimmable LED/COB Downlighter with Die cast housing made of aluminum and white. Powder coated finish. Diming should be Based LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000-6000K CCT with minimum life cycle 50000 hrs burning hours at 50˚C. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%.

13 6.88 Supplying , installation , testing and commissioning for the following LED RGB / RGBW Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . Luminaire shall be capable of producing dynamic color changing light with 16 million colors by DMX / Ethernet based control . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor >0.9 . Fixture shall be suitable to operate at ambient temperature range of -10 Degree C to +50 Degree C and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required.

14 6.16 Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.

15 6.18.5 Supplying, installation, testing and commissioning of following COB LED Spot Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 8 Each 2848.00 22,784.00

16 6.26 Supplying, installation, testing and commissioning of following LED Signage entry/exit having minimum size 300mm (L) x 200mm (H) x 45mm (W), fitting complete including built in battery backup for 2 hour with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-20,6.26.2- Double sided LED Signage 8 Each 4626.00 37,008.00

ITC fluorescent fitting with down rods:

17 6.4 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification. 25 Each 2662.00 66,550.00

18 6.6 Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9

19 5.9 Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as per specification. 8 Each 42.00 336.00

Sub Head 3 : Switchboards

20 9.4 Supplying and fixing on surface/ recess horizontal type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator)

20.1 9.4.4 4 way Double door 1 Each 1716.00 1,716.00

20.2 9.4.5 6 way Double door 2 Each 2038.00 4,076.00

20.3 9.4.6 8 way Double door 2 Each 2547.00 5,094.00

21 9.11 Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

22 9.20 Supplying and fixing following rating, 415 volts, FOUR POLES, ISOLATOR in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

23 9.22 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

Sub Head 4 : Earthing

24 12.19 Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification:

12.19.1 With 3 metre long GI Pipes and 50 kg back filling compound. 1 Each 10955.00 10,955.00

25 12.13 Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification. 15 Metre 94.00 1,410.00

26 12.17 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as per specification. 200 Metre 38.00 7,600.00

Sub Head 5 : Cable and cable management

27 15.3 Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

28 15.5 Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as required.

29 15.13 Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010).

30 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

14.1 Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.

14.1.1 63 mm outer dia 25 Metre 184.00 4,600.00

BRASS COMPRESSION GLAND

31 15.24 Supplying and making end termination with brass compression gland and copper lugs for following size armoured copper conductor power cable of 1.1 KV grade as per specification.

32 18.1 Supplying and installing following size powder coated, perforated M.S. cable trays with perforation not more than 17.5% rigidly suspended from the ceiling with M.S. suspenders at a distance not more than 2.5 metre and near every junction/ joint etc complete as per specification.

18.1.2 150 mm width X 50 mm depth X 1.6 mm thickness 85.47 Metre 314.00 26,837.58

33 7.19 Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured)

34 7.20 Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification.

35 9.1 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.

9.1.6 3 pole MCCB, 160A, Adjustable Thermal - Magnetic Release, 25KA 1 Each 7623.00 7,623.00

36 9.16 Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

37 10.9 Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification.

38 10.15 Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification.

39 10.17 Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification. 2 Each 94.00 188.00

40 10.20 Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.20.2 Digital type 1 Each 835.00 835.00

41 10.18 Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

FIRST FLOOR SANITATION & WATER SUPPLY WORK

1 18.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.1.3 White Orissa pattern W.C. pan of size 580x440 mm 6.00 each

2 18.4 Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.4.3 White wall hung type 6.00 each

3 18.13 Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete:

18.13.2 Flat back type urinal of size 460x380x250mm

Urinal 10.00 each

4 18.17 Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

18.17.5 White Oval or round size 550x400mm.

Wash Basin 10.00 each

5 18.25 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Kitchen sink & wash basins 10.00 each

6 18.26 Providing and fixing PVC waste coupling in wash basin/ sink.

Kitchen sink & wash basins 10.00 each

7 18.76 Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete.

18.76.2 110 mm dia pipe. 200 meter

18.76.3 150 mm dia pipe. 180 meter

8 18.77 Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

8.1 18.77.1 Tee/ Tee with door/ Bend 45°/ Bend 90°

8.4 18.77.6 Nahani trap 110x75mm 35.00 each

9 19.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

9.1 19.6.1 15 mm nominal outer dia pipes 80.77 meter

9.2 19.6.1 20 mm nominal outer dia pipes 90 meter

9.3 19.6.3 25 mm nominal outer dia pipes 90 meter

9.4 19.6.4 32 mm nominal outer dia pipes 220 meter

9.5 19.6.5 40 mm nominal outer dia pipes 220 meter

9.6 19.6.5 50 mm nominal outer dia pipes 205 meter

10 19.14 Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:

10.1 19.14.2 Long nose bib cock (500 grams) 25.00 each

10.2 19.14.6 Stop cock (concealed) (600 grams) 200.00 each

10.3 19.14.9 Kitchen sink mixer with cast swivel spout (1000 grams) 1.00 each

10.4 19.14.10 Wall mixer with elegant knob (1400 grams) 5.00 each

10.5 19.14.15 Shower rose (revolving type) (150mm) 5.00 each

11 19.15 Providing and fixing stainless steel drain jali of approved make/quality. 25.00 each

12 19.16 Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end):

12.1 19.16.1 25 mm nominal bore 12.00 each

12.2 19.16.4 32 mm nominal bore 12.00 each

12.3 19.16.5 40 mm nominal bore 12.00 each

13 20.29 Providing and constructing brick masonry chamber for underground pipe and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) RCC cover of suitable size and 75mm thick with 1:1.5:3 mix (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including reinforcement 8mm dia bars at 150mm both ways and MS hooks for lifting, including foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

13.1 20.29.1 Inside dimensions 450x600 mm and 45 cm deep for single pipe line : 5.00 each

13.2 20.29.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : 5.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

FF FIRE FITING WORK

BUILDING SOR 2015

1 23.1 Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line.

2 23.2 Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.

3 23.5 Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required..

23.5.1 80 mm dia 5.00 each

4 23.7 Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified.

5 23.7.2 50 mm dia 5.00 each

6 23.13 Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required. 75.00 each

7 23.14 Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

HOSE REEL DRUM 5.00 each

8 23.18 Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

HYDRANT VALVE 5.00 each

9 23.22 Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

RRL hose pipe 5.00 each

10 23.24 Supplying & fixing 63 mm dia Stainless Steel IS: 3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzle conforming to IS: 903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

branch pipe 5.00 each

11 23.25 Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required.

23.25.2 Size 900 mm x 600 mm x 500 mm 5.00 each

ELECTRICAL SOR 2020

12 26.17 Supply and erecting of following ISI marked Fire extenguishers on wall/ column including erecting bracket etc complete.

12.1 26.17.5 CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve 5.00 each

12.2 26.17.3 ABC Fire Extinguisher 4KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 2A, 89B. With all accessories. 5.00 each

13 26.1 Suppying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 50 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes, 1.00 each

14 26.9 Suppying , installation , testing and commissioning of Intelligent Addressable Multi-sensor Smoke detector: Multi-criteria addressable fire detector that incorporates photoelectric and thermal sensors,Polarity insensitive utilizing SureWireTM technology,Tri-color detector status LED with 360° viewing,Field-selectable application profiles,Superior EMI immunity, Remote sensitivity-measurement capability,Automatic environment compensation,UL Listed and ULC Listed; FM Approved. 205.00 each

15 26.11 Suppying , installation , testing and commissioning of Intelligent Addressable Type Manual Call Point: Intelligent Manual Fire Alarm Box is constructed of durable, molded and polycarbonate material that is matte finished in red with raised white lettering Single-action,Pull-down lever is down, until manually reset,Polarity insensitive via SureWireTM technology 15.00 each

16 26.13 Suppying , installation , testing and commissioning of Conventional Type Hooter with Strobe: Hooter with Strobe. Wall Mount models feature field selectable candela settings of 15/30/75/110cd and 135/185cd. Ceiling Mount models feature field selectable candela settings of 15/30/75/95cd and 115/177cd. UL Listed, ULC, FM approved. NFPA Compliant. Red. 10.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

1 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 230.12 Cum

2 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.1 Thermo-Mechanically treated bars FE 415 27614.53 kg

3 2.1 Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

3.1 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 107.60 Sqm

3.2 2.1.6 Columns, beams & walls- circular or any other geometrical shape other than square and rectangular in all sizes 217.41 Sqm

3.3 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ) 649.50 Sqm

3.4 2.1.8 Beams, lintels, cantilevers & walls 601.31 Sqm

3.5 2.1.15 Stair cases of all types excluding spiral and folded plate type, including risers and landings 44.45 sqm

4 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 58.63 Cum

5 7.11 Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level

7.11.2 Cement Mortar 1:4 (1 cement : 4 coarse sand) 39.26 sqm

6 7.20 Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry. 39.26 sqm

7 8.4 Providing and fixing Dash fastener (for fixing door/ window frames) on C.C. / R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.

8.4.3 Dash fastener 12x100mm 33.00 each

8 8.16 Providing and fixing PVC membrane foil coated (laminated) flush door shutters, made with core of block board with frame of first class hard wood, coated with 0.30mm membrane pasted with resin using vacuam treatment process complete all but excluding hinges.

8.16.1 35 mm thick (single leaf) 11.28 sqm

9 8.58 Providing and fixing bright finished brass butt hinges with brass polished MS screws complete:

8.58.1 125x85x5.50 mm (Heavy Type) 33.00 each

10 8.60 Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete:

11 8.61 Providing and fixing brass door latch with brass polished MS screws complete:

12 8.62 Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:

13 8.86 Providing and fixing 100mm antique/ SS finished brass mortise latch and lock with six levers and a pair of lever handles with antique/ SS polished MS screw complete. 4.00 each

14 8.141 Providing and fixing Stainless steel "D" shape door handles made of 10mm dia rod with necessary stainless steel screws etc complete.

15 8.154 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 11.03 sqm

16 8.158 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 4.00 each

17 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer. 4121.02 kg

18 9.47 Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately:

18.1 9.47.1 For fixed portion 1490.91 kg

18.2 9.47.2 For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately). 22.95 Kg

19 9.49 Extra for polyester powder coated (minimum 50 micron) aluminium sections instead of anodized. 1513.86 Kg

20 9.51 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item):

9.51.2 With float glass panes of 5 mm thickness 3.06 sqm

21 9.58 Extra for providing and fixing tinted glass panes in aluminium door, window, ventilator shutters and partitions instead of float glass.

9.58.2 5 mm thickness 3.06 sqm

22 9.57 Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete.

9.57.2 SS Grade 304 1183.35 kg

23 9.63 Providing and fixing clear float toughened glass door or partition in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignment with all labour tools and tackles etc complete. (Patch fittings and hardware to be paid for separately).

9.63.1 12 mm thick for door/partition 10.56 sqm

9.63.3 6 mm thick for glazing etc. 169.61 sqm

24 9.64 Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete.

1. Top patch with pivot SS grade 304 20.00 Nos.

2. Top/side patch glass or L-connector patch SS grade-304 40.00 Nos.

3. Bottom patch to be connected with floor machine 20.00 Nos.

4. Bottom lock patch with three key SS grade 304 20.00 Nos.

5. Corner patch fitting with pivot SS grade 304 20.00 Nos.

6. Two way action Hydraulic floor spring machine heavy duty double cylinder type Capacity 120/150 kg mounted on floor including required cutting on floor and proper grouting with rich cement mortar. 2.00 Nos.

7. H type handle 32x600mm SS 304 grade 4.00 Nos.

8. Floor/Wall to Glass Connector SS grade 304 40.00 Nos.

25 10.61 Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting. 65.58 sqm

26 10.67 Providing and fixing Acoustical Suspended Ceiling System made of tiles of size 595x595mm and specified thickness as approved by Engineer-In-Charge, in tru Horizontal Level Suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanised @120 gsm both side inclusive) consisting of main "T" Runner with suitably spaced joints to get required lenght and of size 24x38 mm made from 0.30 thick(minimum ) sheet, spaced at 1200mm center to center and cross "T" of size 24x38mm made of 0.30 thick (minimum) sheet, 1200 mm long spaced between main "T" at 600mm center to lenght 600 mm and size 24x38mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24mm and laying false ceiling tiles of approved texture in the grid, cutting/ making opening for services like diffusers, grills light fitting, fixtures, smoke detectors etc wherever required. Main "T" runner to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6 mm fixed to ceiling with 12.5mm dia and 50mm long

dash fasteners, 4mm dia GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center ot center along main "T". Bottom exposed width of 24mm of all "T" sections shall be pre-painted with polyster paint, all complete for all heights as per specification drawings or as directed by Enginner-In-Charge. The tiles should have Humidity resistance (RH) of 99%, Light Reflectance>83%, Thermal Conductivity K=0.052-0.57 w/mk, color white, fire performance UKclass0/Class1(BS476pt-6and7) in module size of 600x600x16 mm with Bio Block coating on the face of the tile, suitable for green building application, with recycled content of 38-41%. Cielinng height up 3.5 mt from adjacent floor level. Extra height to be paid serately.

10.67.2 With 20 mm thick bevelled/tegular edged mineral fibre false ceiling tile (NRC 0.7) 602.55 sqm

27 10.71 amendment Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595 mm, having NRC(Noise Reuction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85%(minimum). Non combustible as per BS:476(part-4), fire performance as per BS:476(part 6&7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, comprising of a frame made from especially fabricated galvanised mild steel steel sheet 0.50 mm thick pressed section (galvanizing @ 120 grams per sqm incluidng both sides) i.e. vertical studs of size 48 x 34 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50x32 m fixed to the floor and soffit at 600 mm centers using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 500mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer's specifiaction as per direction of Engineer-In-Charge all complete.

Wall Panaling Work 458.34 sqm

28 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand) 641.24 sqm

29 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 640.18 sqm

30 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 366.30 sqm

31 11.9 Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer. 36.63 kg

32 12.45 15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above)

12.45.3 Granite stone lakha red/ shahi red 815.01 sqm

33 12.46 15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m).

12.46.3 Granite stone lakha red/ shahi red 48.58 sqm

34 12.44 Extra for nosing in Granite stone for treads. 67.20 metre

35 12.74 Providing and fixing rectified glazed ceramic Floor tiles of 1st quality conforming to IS : 15622-2017 of approved make, in all colours, shades over 20 mm thick bed of cement Mortar 1:3 (1 cement:3 coarse sand ) and jointing with grey cement sluryy @ 3.3 kg per sqm including pointing in white cement mixed with matching pigment complete.

12.74.3 Size 600x600mm thickness 8 to 9mm 46.92 sqm

36 12.75 Providing and fixing recified glazed ceramic wall/dado tiles of 1st quality conforming to IS:15622-2017 of approved make, in all colors, shades on wall and dados over 12 mm thick bed of cement Mortar 1:3(1 cement:3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete.

12.75.2 Size 300x600mm thickness 7 to 8mm 191.73 sqm

37 13.6 15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish.

13.6.2 Granite stone black 80.48 sqm

38 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 366.30 Sqm

39 14.57 Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied @ 4.0 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Asian trucare, Berger Happy walls Putty Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work . (This Item to be use in heigher grade painting works Item No. 14.65) 1281.42 Sqm

40 14.65 Providing and applying Luxury plastic enmulsion paint with roller application minimum three Coats applied @ 1.25 lit / 10Sqm up to final finish as per relevant Type - 1 Class D, C, B & A (Glossy /Semi Glossy and Matt , Egg Shell or Satin finish ) of required shade (Product such as Asian Royale Shyne,Dulux Velvet Touch, Berger Silk Luxury Emulsion ,Nippon Impression Pearl, Opus Pure Elegance) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc, complete for the work. (with 4 Years Warranty ) 257.36 sqm

41 14.69 Providing and applying exterior surface with PREMIUM HEAVY DUTY Glossy or Matt Finish Exterior Emulsion paint of required shade to give protective and water proof finish minimum three coats applied @ 143 lit/ 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D,C,B & A (Glossy / matt / Egg Shell finish )having high DFT and silicon aditive for elastomaric property (Product such as Asian Ultima Dulux Weathershield Maxx , Berger Weathercoat All Guard Nerolac Excel Total , Nippon Durafresh Expert, Opus Tru Look) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. (With 4 Year Warranty) 366.30 sqm

42 14.72 Providing and applying Glossy finish Enamel paint mimimum 2 Coats in al surface applying @ 0.75 lit/ 10 Sqm up to required finish as per relevent I.S. code 2932: 2013 of (Product such as Asian Apcolite Premium Enamel Dulux Promise Premium Enamel Nerolac Synthatic Enamel, Opus Prime enamel ) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackle and labour etc. complete for the work. 164.84 sqm

43 24.23 Ele. Sor 2020 Supplying, installation, testing and commissiong of following size drinking water cooler storage type ISI marked, eco friendly non CFC refrigarant, water tank and cooler cabinet sheet material- stainless steel {grade AISI 304} with thickness>= 0.8 mm, with PUF insulation including all accessories connection etc complete as per specification.

24.23.3 150/300 Ltrs/hr 1.00 Each

44 24.24 Ele. Sor 2020 Supplying, installation, testing and commissiong of following capacity of RO purification system with UF/UV/TDS controler and UV lamp {IS 14724 Ultra voilet disinfection} and minimum three stage purification, automatic on/off, output water conferming standard IS 10500 with inbuild storage tank including all accessories connection etc complete as per specification.

24.24.2 50 Ltrs/hr output capacity 1.00 Each

Second Floor Electrification Work

Second Floor Plumbing Work of

Second Floor Firefighting Work

Total (A+B+C+D) 0.00

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

SECOND FLOOR ELECTRICAL WORK

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

Sub Head 1 : Point Wiring

1 1.7 Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Liqhtpoints / Ex Fan points

1.1 1.7.1 Short Point 15 Point 266.00 3,990.00

1.2 1.7.2 Medium Point 40 Point 424.00 16,960.00

1.3 1.7.3 Long Point 30 Point 588.00 17,640.00

Twin control liqht point

2 1.8 Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 5 Point 420.00 2,100.00

3 1.9 Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 15 Point 216.00 3,240.00

4 1.11 Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

4.1 1.11.3 Long Point 3 Point 1350.00 4,050.00

4.2 1.11.4 Extra Long Point I 10 Point 1807.00 18,070.00

4.3 1.11.5 Extra Long Point II 8 Point 2315.00 18,520.00

4.4 1.11.6 Extra Long Point III 8 Point 2825.00 22,600.00

Sub Main in Concealed PVC Conduit

5 1.13 Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

5.1 1.13.1 3 X 1.5 sq. mm in 20mm conduit 350 Metre 92.00 32,200.00

5.2 1.13.2 3 X 2.5 sq. mm in 20mm conduit 100 Metre 111.00 11,100.00

5.3 1.13.3 6 X 2.5 sq. mm in 25mm conduit 120 Metre 172.00 20,640.00

5.4 1.13.4 9 X 2.5 sq. mm in 32mm conduit 65 Metre 238.00 15,470.00

5.5 1.13.6 3 X 4 sq. mm in 25mm conduit 65 Metre 145.00 9,425.00

5.6 1.13.7 3 X 6 sq. mm in 25mm conduit 8 Metre 182.00 1,456.00

6 3.12 Supplying and drawing following pair 0.5 mm FR PVC insulated copper conductor, unarmored telephone wire in the existing surface/ concealed Steel/FRLS PVC conduit as per specification

7 3.14 Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification 100 metre 19.00 1,900.00

8 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

9 4.4 Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

10 4.5 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

11 5.4 Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.

11.1 5.4.1 5/6 amps one way switch 20 Each 69.00 1,380.00

11.3 5.4.5 3 pin 5/6 amp socket outlet 10 Each 96.00 960.00

11.4 5.4.6 6 pin 15/16 amp socket outlet 10 Each 120.00 1,200.00

11.5 5.4.9 Fan regulator (two module size) electronic stepped type moving all rounds 20 Each 223.00 4,460.00

11.6 5.4.15 Telephone socket outlet 5 Each 70.00 350.00

11.7 5.4.17 Computer Outlet Jack 10 Each 242.00 2,420.00

11.8 5.4.20 Ceiling rose 3 pin 5 amp 10 Each 40.00 400.00

12 5.6 Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification. 8 Each 816.00 6,528.00

Sub Head 2 : Accessories, Luminaires and Fans

12 6.71 Supplying , installation , testing and commissioning of following recess mounted DALI/0-10volt Analogue dimmable LED/COB Downlighter with Die cast housing made of aluminum and white. Powder coated finish. Diming should be Based LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000-6000K CCT with minimum life cycle 50000 hrs burning hours at 50˚C. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%.

13 6.88 Supplying , installation , testing and commissioning for the following LED RGB / RGBW Linear wall washer luminaire for façade lighting with aluminium extruded housing of following wattage . Luminaire shall be capable of producing dynamic color changing light with 16 million colors by DMX / Ethernet based control . The beam angle of the fitting shall be narrow , medium , wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any seperate power supply from 100 to 270 V AC , 50 Hz , power factor >0.9 . Fixture shall be suitable to operate at ambient temperature range of -10 Degree C to +50 Degree C and shall be IP 65 and IK 06 rated . Lifetime should be at atleast L70:50000 burning hours at 50 Degree C . Luminaire shall be conforming to BIS and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables , water proof connectors etc as required.

14 6.16 Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.

15 6.18.5 Supplying, installation, testing and commissioning of following COB LED Spot Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 8 Each 2848.00 22,784.00

16 6.26 Supplying, installation, testing and commissioning of following LED Signage entry/exit having minimum size 300mm (L) x 200mm (H) x 45mm (W), fitting complete including built in battery backup for 2 hour with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-20,6.26.2- Double sided LED Signage 8 Each 4626.00 37,008.00

ITC fluorescent fitting with down rods:

17 6.4 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification. 26 Each 2662.00 69,212.00

18 6.6 Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9

19 5.9 Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as per specification. 8 Each 42.00 336.00

Sub Head 3 : Switchboards

20 9.4 Supplying and fixing on surface/ recess horizontal type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator)

20.1 9.4.4 4 way Double door 1 Each 1716.00 1,716.00

20.2 9.4.5 6 way Double door 2 Each 2038.00 4,076.00

20.3 9.4.6 8 way Double door 2 Each 2547.00 5,094.00

21 9.11 Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

22 9.20 Supplying and fixing following rating, 415 volts, FOUR POLES, ISOLATOR in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

23 9.22 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

Sub Head 4 : Earthing

24 12.19 Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification:

12.19.1 With 3 metre long GI Pipes and 50 kg back filling compound. 1 Each 10955.00 10,955.00

25 12.13 Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification. 15 Metre 94.00 1,410.00

26 12.17 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as per specification. 200 Metre 38.00 7,600.00

Sub Head 5 : Cable and cable management

27 15.3 Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

28 15.5 Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as required.

29 15.13 Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010).

30 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

14.1 Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.

14.1.1 63 mm outer dia 25 Metre 184.00 4,600.00

BRASS COMPRESSION GLAND

31 15.24 Supplying and making end termination with brass compression gland and copper lugs for following size armoured copper conductor power cable of 1.1 KV grade as per specification.

32 18.1 Supplying and installing following size powder coated, perforated M.S. cable trays with perforation not more than 17.5% rigidly suspended from the ceiling with M.S. suspenders at a distance not more than 2.5 metre and near every junction/ joint etc complete as per specification.

18.1.2 150 mm width X 50 mm depth X 1.6 mm thickness 88.285 Metre 314.00 27,721.49

33 7.19 Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured)

34 7.20 Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification.

35 9.1 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.

9.1.6 3 pole MCCB, 160A, Adjustable Thermal - Magnetic Release, 25KA 1 Each 7623.00 7,623.00

36 9.16 Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

37 10.9 Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification.

38 10.15 Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification.

39 10.17 Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification. 2 Each 94.00 188.00

40 10.20 Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.20.2 Digital type 1 Each 835.00 835.00

41 10.18 Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

SECOND FLOOR SANITATION & WATER SUPPLY WORK

1 18.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.1.3 White Orissa pattern W.C. pan of size 580x440 mm 6.00 each

2 18.4 Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

18.4.3 White wall hung type 6.00 each

3 18.13 Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete:

18.13.2 Flat back type urinal of size 460x380x250mm

Urinal 10.00 each

4 18.17 Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required :

18.17.5 White Oval or round size 550x400mm.

Wash Basin 10.00 each

5 18.25 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Kitchen sink & wash basins 10.00 each

6 18.26 Providing and fixing PVC waste coupling in wash basin/ sink.

Kitchen sink & wash basins 10.00 each

7 18.76 Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete.

18.76.2 110 mm dia pipe. 205 meter

18.76.3 150 mm dia pipe. 180 meter

8 18.77 Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

8.1 18.77.1 Tee/ Tee with door/ Bend 45°/ Bend 90°

8.4 18.77.6 Nahani trap 110x75mm 35.00 each

9 19.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

9.1 19.6.1 15 mm nominal outer dia pipes 85.55 meter

9.2 19.6.1 20 mm nominal outer dia pipes 90 meter

9.3 19.6.3 25 mm nominal outer dia pipes 90 meter

9.4 19.6.4 32 mm nominal outer dia pipes 220 meter

9.5 19.6.5 40 mm nominal outer dia pipes 220 meter

9.6 19.6.5 50 mm nominal outer dia pipes 205 meter

10 19.14 Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:

10.1 19.14.2 Long nose bib cock (500 grams) 25.00 each

10.2 19.14.6 Stop cock (concealed) (600 grams) 200.00 each

10.3 19.14.9 Kitchen sink mixer with cast swivel spout (1000 grams) 1.00 each

10.4 19.14.10 Wall mixer with elegant knob (1400 grams) 5.00 each

10.5 19.14.15 Shower rose (revolving type) (150mm) 5.00 each

11 19.15 Providing and fixing stainless steel drain jali of approved make/quality. 25.00 each

12 19.16 Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end):

12.1 19.16.1 25 mm nominal bore 12.00 each

12.2 19.16.4 32 mm nominal bore 12.00 each

12.3 19.16.5 40 mm nominal bore 12.00 each

13 20.29 Providing and constructing brick masonry chamber for underground pipe and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) RCC cover of suitable size and 75mm thick with 1:1.5:3 mix (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including reinforcement 8mm dia bars at 150mm both ways and MS hooks for lifting, including foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

13.1 20.29.1 Inside dimensions 450x600 mm and 45 cm deep for single pipe line : 5.00 each

13.2 20.29.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : 5.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

SF FIRE FITING WORK

BUILDING SOR 2015

1 23.1 Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line.

2 23.2 Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.

3 23.5 Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required..

23.5.1 80 mm dia 5.00 each

4 23.7 Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified.

5 23.7.2 50 mm dia 5.00 each

6 23.13 Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required. 75.00 each

7 23.14 Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

HOSE REEL DRUM 5.00 each

8 23.18 Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

HYDRANT VALVE 5.00 each

9 23.22 Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

RRL hose pipe 5.00 each

10 23.24 Supplying & fixing 63 mm dia Stainless Steel IS: 3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzle conforming to IS: 903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

branch pipe 5.00 each

11 23.25 Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required.

23.25.2 Size 900 mm x 600 mm x 500 mm 5.00 each

ELECTRICAL SOR 2020

12 26.17 Supply and erecting of following ISI marked Fire extenguishers on wall/ column including erecting bracket etc complete.

12.1 26.17.5 CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve 5.00 each

12.2 26.17.3 ABC Fire Extinguisher 4KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 2A, 89B. With all accessories. 5.00 each

13 26.1 Suppying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 50 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes, 1.00 each

14 26.9 Suppying , installation , testing and commissioning of Intelligent Addressable Multi-sensor Smoke detector: Multi-criteria addressable fire detector that incorporates photoelectric and thermal sensors,Polarity insensitive utilizing SureWireTM technology,Tri-color detector status LED with 360° viewing,Field-selectable application profiles,Superior EMI immunity, Remote sensitivity-measurement capability,Automatic environment compensation,UL Listed and ULC Listed; FM Approved. 205.00 each

15 26.11 Suppying , installation , testing and commissioning of Intelligent Addressable Type Manual Call Point: Intelligent Manual Fire Alarm Box is constructed of durable, molded and polycarbonate material that is matte finished in red with raised white lettering Single-action,Pull-down lever is down, until manually reset,Polarity insensitive via SureWireTM technology 15.00 each

16 26.13 Suppying , installation , testing and commissioning of Conventional Type Hooter with Strobe: Hooter with Strobe. Wall Mount models feature field selectable candela settings of 15/30/75/110cd and 135/185cd. Ceiling Mount models feature field selectable candela settings of 15/30/75/95cd and 115/177cd. UL Listed, ULC, FM approved. NFPA Compliant. Red. 10.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

1 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 38.91 Cum

2 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.1 Thermo-Mechanically treated bars FE 415 4669.18 kg

3 2.1 Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

3.1 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 75.60 Sqm

3.2 2.1.6 Columns, beams & walls- circular or any other geometrical shape other than square and rectangular in all sizes 22.06 Sqm

3.3 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ) 90.65 Sqm

3.4 2.1.8 Beams, lintels, cantilevers & walls 48.91 Sqm

4 4.6 Providing and laying integral cement based water proofing treatment on roofs, balconies, terraces etc with average thickness of 120mm and minimum thickness at khurra as 65 mm, consisting of following operations including surface preparation: i) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement mixed with water proofing compound conforming to IS. 2645 over the RCC slab including adjoining walls upto 300mm height.

ii) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) mixed with water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) mixed with water proofing compound conforming to IS : 2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

iii) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645.

iv) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) mixed with water proofing compound conforming to IS : 2645 including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep.

v) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order: 691.17 sqm

5 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 30.77 Cum

6 8.4 Providing and fixing Dash fastener ( for fixing door / window frames ) on C.C. / R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.

8.4.3 Dash fastener 12x100mm 6.00 each

7 8.16 Providing and fixing PVC membrane foil coated (laminated) flush door shutters, made with core of block board with frame of first class hard wood, coated with 0.30mm membrane pasted with resin using vacuam treatment process complete all but excluding hinges.

8.16.1 35 mm thick (single leaf) 2.16 sqm

8 8.58 Providing and fixing bright finished brass butt hinges with brass polished MS screws complete:

8.58.1 125x85x5.50 mm (Heavy Type) 3.00 each

9 8.60 Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete:

10 8.61 Providing and fixing brass door latch with brass polished MS screws complete:

11 8.62 Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:

12 8.86 Providing and fixing 100mm antique/ SS finished brass mortise latch and lock with six levers and a pair of lever handles with antique/ SS polished MS screw complete. 2.00 each

13 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer. 398.93 kg

14 9.47 Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately:

14.1 9.47.1 For fixed portion 135.63 kg

14.2 9.47.2 For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).

For Wt. @ 5kg/Sqm 37.27 Kg

15 9.49 Extra for polyester powder coated (minimum 50 micron) aluminium sections instead of anodized. 172.91 Kg

16 9.51 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item):

9.51.2 With float glass panes of 5 mm thickness 15.96 sqm

17 9.58 Extra for providing and fixing tinted glass panes in aluminium door, window, ventilator shutters and partitions instead of float glass.

9.58.2 5 mm thickness 15.96 sqm

18 10.61 Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. wall/partition with the help of

channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to

rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge

gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting. 70.14 sqm

19 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand) 90.65 sqm

20 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 148.66 sqm

21 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 292.55 sqm

22 11.9 Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer. 29.26 kg

23 4.6 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. ii) 2nd layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. iii) 3rdlayer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with coarse sand @ 1.289 kg/sqm and water proofing cement compound @ 0.07 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. 691.17 sqm

24 Amedment 12.79 Providing and laying DOUBLE/MULTI CHARGE (minimum 2.0mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS:15622-2017 of approved make in all colours and shades and size mentioned below (+/- 10 mm), laid on 20mm thick cement mortar 1:4(1 cement:4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

12.79.1 Size 600x600mm thickness 9 to 10mm 691.17 sqm

25 13.6 15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish.

13.6.2 Granite stone black 9.24 sqm

26 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 292.55 Sqm

1 14.57 Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied @ 4.0 kg/ 10Sqm as per relevant IS code 17545 : 2021 (Product such as Asian trucare, Berger Happy walls Putty Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work . (This Item to be use in heigher grade painting works Item No. 14.65) 239.31 Sqm

27 14.65 Providing and applying Luxury plastic enmulsion paint with roller application minimum three Coats applied @ 1.25 lit / 10Sqm up to final finish as per relevant Type - 1 Class D, C, B & A (Glossy /Semi Glossy and Matt , Egg Shell or Satin finish ) of required shade (Product such as Asian Royale Shyne,Dulux Velvet Touch, Berger Silk Luxury Emulsion ,Nippon Impression Pearl, Opus Pure Elegance) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc, complete for the work. (with 4 Years Warranty ) 175.55 sqm

28 14.69 Providing and applying exterior surface with PREMIUM HEAVY DUTY Glossy or Matt Finish Exterior Emulsion paint of required shade to give protective and water proof finish minimum three coats applied @ 143 lit/ 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D,C,B & A (Glossy / matt / Egg Shell finish )having high DFT and silicon aditive for elastomaric property (Product such as Asian Ultima Dulux Weathershield Maxx , Berger Weathercoat All Guard Nerolac Excel Total , Nippon Durafresh Expert, Opus Tru Look) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. (With 4 Year Warranty) 292.55 sqm

29 14.22 Painting on new work (two or more coats) to give an even shade with: 15.96 sqm

Stair Tower Electrification Work

Stair Tower Plumbing Work of

Stair Tower Firefighting Work

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

STAIR TOWER ELECTRICAL WORK

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

Sub Head 1 : Point Wiring

Twin control liqht point

1 1.8 Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 1 Point

2 1.9 Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 5 Point

3 1.11 Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

3.1 1.11.3 Long Point 1 Point

3.2 1.11.4 Extra Long Point I 3 Point

3.3 1.11.5 Extra Long Point II 4 Point

3.4 1.11.6 Extra Long Point III 4 Point

Sub Main in Concealed PVC Conduit

4 1.13 Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

4.1 1.13.1 3 X 1.5 sq. mm in 20mm conduit 60 Metre

4.2 1.13.2 3 X 2.5 sq. mm in 20mm conduit 30 Metre

4.3 1.13.3 6 X 2.5 sq. mm in 25mm conduit 30 Metre

4.4 1.13.4 9 X 2.5 sq. mm in 32mm conduit 15 Metre

4.5 1.13.6 3 X 4 sq. mm in 25mm conduit 15 Metre

4.6 1.13.7 3 X 6 sq. mm in 25mm conduit 5 Metre

5 3.12 Supplying and drawing following pair 0.5 mm FR PVC insulated copper conductor, unarmored telephone wire in the existing surface/ concealed Steel/FRLS PVC conduit as per specification

3.12.2 2 Pair 20 Metre

6 3.14 Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification 20 metre

7 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

8 4.4 Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

8.1 4.4.2 100mmX75mm (3 Module) 1 Each

8.2 4.4.4 200mmX75mm (6 Module) 1 Each

9 4.5 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

9.1 4.5.3 3 Module 1 Each

9.2 4.5.5 6 Module 1 Each

10 5.4 Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification.

10.1 5.4.1 5/6 amps one way switch 3 Each

10.2 5.4.4 15/16 amp switch 2 Each

10.3 5.4.5 3 pin 5/6 amp socket outlet 2 Each

10.4 5.4.6 6 pin 15/16 amp socket outlet 2 Each

Sub Head 2 : Accessories, Luminaires and Fans

11 6.71 Supplying , installation , testing and commissioning of following recess mounted DALI/0-10volt Analogue dimmable LED/COB Downlighter with Die cast housing made of aluminum and white. Powder coated finish. Diming should be Based LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000-6000K CCT with minimum life cycle 50000 hrs burning hours at 50˚C. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%.

11.1 6.71.3 18 watt 2 Each

11.2 6.71.4 20 watt 2 Each

11.3 6.71.5 30 watt 1 Each

11.4 6.71.7 50 watt 1 Each

12 6.18.5 Supplying, installation, testing and commissioning of following COB LED Spot Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 4 Each

13 6.26 Supplying, installation, testing and commissioning of following LED Signage entry/exit having minimum size 300mm (L) x 200mm (H) x 45mm (W), fitting complete including built in battery backup for 2 hour with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-20,6.26.2- Double sided LED Signage 4 Each

ITC fluorescent fitting with down rods:

Sub Head 3 : Switchboards

14 9.4 Supplying and fixing on surface/ recess horizontal type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator)

14.1 9.4.4 4 way Double door 1 Each

14.2 9.4.5 6 way Double door 1 Each

14.3 9.4.6 8 way Double door 1 Each

15 9.11 Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.11.2 6 amps to 32 amps 54 Each

16 9.20 Supplying and fixing following rating, 415 volts, FOUR POLES, ISOLATOR in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.20.1 40 amps 1 Each

9.20.2 63 amps 1 Each

17 9.22 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.22.2 40 amps 1 Each

9.22.3 63 amps 1 Each

Sub Head 4 : Earthing

18 12.19 Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification:

12.19.1 With 3 metre long GI Pipes and 50 kg back filling compound. 1 Each

19 12.13 Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification. 10 Metre

20 12.17 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as per specification. 50 Metre

Sub Head 5 : Cable and cable management

21 15.3 Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

22 15.5 Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as required.

15.5.13 4 x 10 sq. mm. 30 Metre

15.5.14 4 x 16 sq. mm. 50 Metre

15.5.15 4 x 25 sq. mm. 10 Metre

23 15.13 Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, steel armoured, copper conductor control /power cable of 1.1 KV grade in exiting PVC/ GI pipe etc as per specification and IS: 694 (2010).

15.13.3 6 x 1.5 sq. mm 25 Metre

24 1.15 Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5)

1.15.2 25 mm 20 Metre

1.15.3 32 mm 20 Metre

14.1 Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.

14.1.1 63 mm outer dia 20 Metre

BRASS COMPRESSION GLAND

25 15.24 Supplying and making end termination with brass compression gland and copper lugs for following size armoured copper conductor power cable of 1.1 KV grade as per specification.

a) 15.24.1 2 X 4 sq. mm (16 mm) 5 Each

26 18.1 Supplying and installing following size powder coated, perforated M.S. cable trays with perforation not more than 17.5% rigidly suspended from the ceiling with M.S. suspenders at a distance not more than 2.5 metre and near every junction/ joint etc complete as per specification.

18.1.2 150 mm width X 50 mm depth X 1.6 mm thickness 87.35 Metre

27 7.19 Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured)

7.19.1 Upto 300 mm deep 1 sqm

28 7.20 Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification.

7.20.3 300 amp (50x5mm) 2 Metre

29 9.1 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.

9.1.6 3 pole MCCB, 160A, Adjustable Thermal - Magnetic Release, 25KA 1 Each

30 9.16 Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.16.3 40 amps 1 Each

9.16.5 63 amps 1 Each

31 10.9 Providing and fixing metal clad, TP&N 4 pole automatic change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification.

10.9.2 160 amps 1 Each

32 10.15 Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.15.3 200/5 amps 1 Each

33 10.17 Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification. 1 Each

34 10.20 Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.20.2 Digital type 1 Each

35 10.18 Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification.

10.18.3 0-200 amps 1 Each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

STAIR TOWER WATER SUPPLY WORK

1 19.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

1.1 19.6.1 15 mm nominal outer dia pipes 23.1 meter

1.2 19.6.4 32 mm nominal outer dia pipes 23.1 meter

1.3 19.6.5 40 mm nominal outer dia pipes 15 meter

2 19.16 Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end):

2.1 19.16.1 25 mm nominal bore 6.00 each

2.2 19.16.4 32 mm nominal bore 8.00 each

2.3 19.16.5 40 mm nominal bore 4.00 each

3 20.29 Providing and constructing brick masonry chamber for underground pipe and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) RCC cover of suitable size and 75mm thick with 1:1.5:3 mix (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including reinforcement 8mm dia bars at 150mm both ways and MS hooks for lifting, including foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

4 19.42 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 15000.00 Litre

5.0 20.29.1 Inside dimensions 450x600 mm and 45 cm deep for single pipe line : 1.00 each

5.1 20.29.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : 1.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. UNIT RATE AMOUNT

TOWER FIRE FITING WORK

BUILDING SOR 2015

1 23.1 Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line.

2 23.2 Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.

3 23.5 Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required..

23.5.1 80 mm dia 1.00 each

4 23.7 Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified.

5 23.7.2 50 mm dia 1.00 each

6 23.13 Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required. 5.00 each

7 23.14 Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

HOSE REEL DRUM 1.00 each

8 23.18 Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

HYDRANT VALVE 1.00 each

9 23.22 Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

RRL hose pipe 1.00 each

10 23.24 Supplying & fixing 63 mm dia Stainless Steel IS: 3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzle conforming to IS: 903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

branch pipe 1.00 each

11 23.25 Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required.

23.25.2 Size 900 mm x 600 mm x 500 mm 1.00 each

ELECTRICAL SOR 2020

12 26.17 Supply and erecting of following ISI marked Fire extenguishers on wall/ column including erecting bracket etc complete.

12.1 26.17.5 CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve 1.00 each

12.2 26.17.3 ABC Fire Extinguisher 4KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 2A, 89B. With all accessories. 1.00 each

13 26.1 Suppying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 50 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes, 1.00 each

14 26.9 Suppying , installation , testing and commissioning of Intelligent Addressable Multi-sensor Smoke detector: Multi-criteria addressable fire detector that incorporates photoelectric and thermal sensors,Polarity insensitive utilizing SureWireTM technology,Tri-color detector status LED with 360° viewing,Field-selectable application profiles,Superior EMI immunity, Remote sensitivity-measurement capability,Automatic environment compensation,UL Listed and ULC Listed; FM Approved. 5.00 each

15 26.11 Suppying , installation , testing and commissioning of Intelligent Addressable Type Manual Call Point: Intelligent Manual Fire Alarm Box is constructed of durable, molded and polycarbonate material that is matte finished in red with raised white lettering Single-action,Pull-down lever is down, until manually reset,Polarity insensitive via SureWireTM technology 5.00 each

16 26.13 Suppying , installation , testing and commissioning of Conventional Type Hooter with Strobe: Hooter with Strobe. Wall Mount models feature field selectable candela settings of 15/30/75/110cd and 135/185cd. Ceiling Mount models feature field selectable candela settings of 15/30/75/95cd and 115/177cd. UL Listed, ULC, FM approved. NFPA Compliant. Red. 5.00 each

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

ACP WALL CLADDING WORK FOR ELEVATION

As Per PWD ( Building ) SOR 2015

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

1 9.60 Designing, providing and fixing aluminium frame work made of special aluminium section on building face with M.S. angle iron brackets fixed on RCC structure with S.S. hold fasteners, including providing and fixing two sided structural adhesive tape of appropriate grade (NORTON or equivalent), on aluminium sections for fixing aluminium/ glass panel, sealing on periphery of frame work, by providing EPDM gasket, silicon weather sealant between aluminium frame and building structure including hire charges of double scaffolding complete.

B LIBRARY CLADING FRAMING 27401.40 Kg

2 9.61 Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work on face of building. (Frame to be paid separately)

9.61.2 4mm thick 190.09 SQM

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

LIFT ( 13 passenger/ 884 Kg )

AS PER ELECTRICALE S.O.R. 2020

SN Sor No. Description of Item Qty. Unit Rate Amount

1 22.7 Suppy, installation, testing & commissitioning and putting into operation and final testing of automatic lift complete with ARD and all standard equipments, accessories and control equipments as per manufacturer's design and as per CPWD specification (Part III LIFTS) 1981and fulfilling following requirments on turn key basis. A. Type : Passenger lift B. Load : 13 passenger/ 884 Kg C. Speed : 1.5 metre per second D. Contol : AC2 E. Operation : Microprosser based simplex collective selective with/without lift attendent F. Total rise : About 9 mtrs G. Landings : 4 All on same side H. Floors served : G,1,2,3 I. Signals : Digital car position indicator, car travel direction indicator in car & at all landings J. Lift shaft size : About 2500 mm width X 1900 mm depth, finished with plaster (size as per actual site conditions) K. Lift car size : About 2000 mm width X 1100 mm depth L. Car entrance : Minimum Clear opening 900 mm wide X 2000 mm high protected with car door M. Landing entrance: Clear opening 900 mm wide X 2000 mm high protected with landing door N. Car door : Stainless steel /Glass Door two pannel telescopic/centre opening flush type O. Landing door : Stainless steel /Glass Door two pannel telescopic/centre opening flush type P. Door operation: Automatic electric power operated door with infra red protection Q. Car interior : Stainless steel pannel with hair line/ mirror/moon rock finish on all sides R. Car floor : Hard wood covered with PVC/ marblex tiles S. Car ceiling & lighting : Fluorscent lighting concealed by suspended false ceiling with plain acrylic diffuser. The frame of suspended false ceiling shall be of powder coated aluminium T. Car ventilation : Pressure fan with anodised aluminium grill U. Emergency lighting in car: Battery operated Emergency lighting in the lift car V. Intercom system : Battery operated Intercom system in lift car, machine room and control room W. Emergency alarm : Battery operated alarm bell system in lift car & contol room X. Position of machine room: Directly above the lift shaft Y. Electric power supply : AC 415 Volts 3 phase 50 Hz terminated in machine room Z. Fire man switch : Fire man switch at main landing termanal 1.00 Job

E.E. A.E. Sub.E. ARCHITECT

Ar. Rohit marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

AIR CONDITIONING

AS PER ELECTRICALE S.O.R. 2020

SN Sor No. Description of Item Qty. Unit Rate Amount

1 24.3 Supplying of approved make split type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 3 metre of copper piping with insulation, etc complete as per specification:

24.3.3 2.0 ton split type capacity 6000 kcal / hr (3 star). 1.00 Each

2 24.4 Installation of split type Inverter/Non Inverter Air Conditioner unit, cooling unit on wall inside and condensing unit on out side wall/ ceiling/ floor at desired locations with existing standard length of copper piping with insulation and power cable including providing and fixing necessary good quality powder coated MS frame etc complete as per specification. (Extra length of copper piping and power cable shall be paid extra on linear basis) 1.00 Each

3 24.10 Supply, connecting and fixing extra length of copper piping for split type air conditioners of following dia and approved quality with insulation sleave etc complete as per specification

4 24.11 Supplying and fixing good quality powder coated MS frame for installation of out door unit of split type Air Conditioner at desired location with atleast 6 nos steel fastners etc complete as per specification 1.00 Set

5 24.12 Supplying, connecting and fixing 15mm dia PVC flexible drain pipe (reinforced with nylon threads) in drain outlet of split type air conditioners etc complete as per specification 10.00 Each

Cost Of 1 Nos TOTAL A 0.00

Cost of 70 Nos 70.00 0.00 0.00

E.E. A.E. S.E. ARCHITECT

Ar. Rohit marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

AS PER BUILDING S.O.R. 1.1.2015

SN REF ITEM DESCRIPTION QTY UNIT RATE AMOUNT

1 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

E.E. A.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

CONSTRUCTION OF CC ROAD & PAVER WORK

AS PER ROAD S.O.R. 01/01/2025

SN REF ITEM DESCRIPTION QTY UNIT RATE AMOUNT

1 3.2 Excavation in Soil (by Mechanical Means.) Excavation for roadway in soil using mechanical means including loading in tipper for carrying of cut earth to embankment site and unloading with all leads & lifts as per relevant clauses of section 300. 491.47 Cum

2 1.1 Transportation Of Metal i/c Loading & Unloading 491.47 Cum

3 3.12 Construction of embankment with Material Obtained from Borrow Pits/Borrow Area Construction of embankment with approved material/selected soil having C.B.R. > 5 (unless specified otherwise in the contract) obtained from borrow pits/borrow area with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. 614.33 Cum.

4 4.1 Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401.

B For Lower Sub-base with

II Grading-VI Material 311.32 Cum.

5 6.1 6.1 Dry Lean Cement Concrete Sub-base as per IRC:SP-49 (Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 26.5 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing as per clause 601.) 155.66 Cum.

6 6.4 Providing and laying Un-reinforced Cement Concrete without Dowel bars including formwork and expansion, contraction & longitudinal joints as per design and as per IRC-62, over a prepared base a per approved mix design and finising to lines and grade as per Drawing for Pavement thickness less than 200mm in Low Volume Roads. With Cement concrete grade M-30 and minimum cement content @ 375 kg/cum 114.56 Cum.

7 4.14 Providing & laying precast interlocking concrete blocks of required compressive strength with approved size, shape/ pattern over coarse sand bed of thickness 30 +/- 5 mm and joints filled with fine sand including leveling with surface vibrator, temping and sweeping etc. complete as per IRC-SP-63.

A 60mm thick precast interlocking concrete block of C.C. M-30 grade on Footpath/Cycle Track

ii Polymer coated coloured precast interlock concrete blocks 655.85 Sqm

8 8.1 Cast in Situ Cement Concrete M20 kerb Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in PCC M20 grade on PCC Ml5 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb concrete to be laid with kerb casting machine, foundation concrete laid manually, all complete as per clause 409. 169.73 Meter

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

CONSTRUCTION OF BRICK BOUNDARY WALL

AS PER BUILDING S.O.R. 1.1.2015

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 198.45 cum

2 1.17 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M. 198.45 cum

3 3.1 Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of form work.

3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). 13.23 cum

4 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size). 44.01 cum

5 3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 15.76 cum

6 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete :

3.12.2 Thermo-Mechanically treated bars FE 500 6574.71 kg

7 2.1 Providing and fixing form work including centering, shuttering, strutting,staging, propping bracing etc. complete and including its removal at all levels, for:

7.1 2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level. 249.87 sqm

7.2 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 227.62 sqm

8 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand) 11.36 cum

9 7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 62.50 cum

10 9.40 Providing and fixing concertina coil fencing with required dia 610 mm (having 50 nos. round per 6 metre length) up to 3m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete as per direction of Engineer-incharge with reinforced barbed tape (R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) 163.05 Meter

11 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 489.15 sqm

12 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 521.76 sqm

13 Amedment 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545:2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 1010.91 sqm

14 Amedment 14.68 Providing and applying on exterior surface with PREMIUM Exterior emulsion paint of required shade to give protective and water proof finish minimum 3 coats applied @ 1.40 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D , C (Glossy /Semi Glossy finish ) (Product such as Asian Apex ,Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon Sumo Etra, Opus True flex) inclusive of providing abro tape on edges and articleand cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.(With 3Year Warranty.) 1010.91 sqm

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

CONSTRUCTION OF SHOP, GUARD ROOM, ENTRANCE GATE & MS GRILL BOUNDARY WALL

AS PER PWD ( Building ) S.O.R. 01.01.2015 & Road S.O.R. 2025

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

( A ) GROUND FLOOR

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 89.59 cum

2 1.6 Extra for every additional lift of 1.5 m or part thereof.

1.6.1 All types of soils 14.93 cum

3 1.17 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M. 89.59 cum

4 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete. 14.16 cum

5 3.1 Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of form work.

3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). 11.07 cum

6 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size). 22.02 cum

7 3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 18.67 cum

8 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.2 Thermo-Mechanically treated bars FE 500 4883.27 kg

9 3.13 Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including form work. 0.43 cum

10 2.1 Providing and fixing form work including centering, shuttering, strutting,staging, propping bracing etc. complete and including its removal at all levels, for:

10.1 2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level. 125.98 sqm

10.2 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 61.83 sqm

10.3 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ) 83.52 sqm

10.4 2.1.8 Beams, lintels, cantilevers & walls 37.16 sqm

11 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand) 8.94 cum

12 7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 25.46 cum

13 8.1 Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position.

8.1.2 Sal, bijasal, benteak, khair, haldu 0.06 cum

14 8.3 Providing 40x5mm iron hold fast 40cm long including fixing to frame with 10mm bolts nuts and wooden plug and embedding in Cement Concrete 1:2:4 in blocks of size 30x10x15cm. 6.00 each

15 8.16 Providing and fixing PVC membrane foil coated (laminated) flush door shutters, made with core of block board with frame of first class hard wood, coated with 0.30mm membrane pasted with resin using vacuam treatment process complete all but excluding hinges.

8.16.1 35 mm thick (single leaf) 1.89 sqm

16 8.58 Providing and fixing bright finished brass butt hinges with brass polished MS screws complete:

8.58.1 125x85x5.50 mm (Heavy Type) 3.00 each

17 8.60 Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete:

18 8.61 Providing and fixing brass door latch with brass polished MS screws complete:

19 8.62 Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete:

20 8.65 Providing and fixing bright finished brass door handles with brass polished MS screws complete:

21 8.158 Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete. 1.00 each

22 9.3 Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer.

9.3.1 Electric resistance or induction butt welded tubes Grade-250 1966.83 kg

9.3.2 Electric resistance or induction butt welded tubes Grade-300 648.00 kg

23 9.61 Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work on face of building. (Frame to be paid separately)

9.61.2 4mm thick 33.53 sqm

24 9.60 Designing, providing and fixing aluminium frame work made of special aluminium section on building face with M.S. angle iron brackets fixed on RCC structure with S.S. hold fasteners, including providing and fixing two sided structural adhesive tape of appropriate grade (NORTON or equivalent), on aluminium sections for fixing aluminium/ glass panel, sealing on periphery of frame work, by providing EPDM gasket, silicon weather sealant between aluminium frame and building structure including hire charges of double scaffolding complete. 117.35 Kg

25 9.6 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer.

9.6.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 819.49 kg

26 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer. 57.60 kg

27 9.47 Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately:

27.1 9.47.1 For fixed portion 14.40 kg

27.2 9.47.2 For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately). 14.40 kg

28 9.51 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item):

9.51.2 With float glass panes of 5 mm thickness 2.88 sqm

29 9.27 Supplying and fixing rolling shutter of approved makes made of M.S. laths interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets,side guides and arrangements for inside and out side locking with push and pull arrangement complete but excluding the cost of top cover and spring.

9.27.2 80x1.20mm M.S. Laths 70.76 Sqm

30 9.28 Providing and fixing 27.5cm long wire spring for rolling shutters. 6.00 Each

31 9.29 Providing and fixing M.S. sheet top cover for rolling shutter

9.29.2 1.20mm thick 23.20 Sqm

32 9.30 Providing and fixing ball bearing for rolling shutters. 24.00 Each

33 9.31 Providing and fixing mechanical device chain and crank operation for operating rolling shutters. 6.00 set

34 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand) 76.32 sqm

35 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 64.80 sqm

36 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 153.90 sqm

37 Amedment 12.79 Providing and laying DOUBLE/MULTI CHARGE (minimum 2.0mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS:15622-2017 of approved make in all colours and shades and size mentioned below (+/- 10 mm), laid on 20mm thick cement mortar 1:4(1 cement:4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

12.79.1 Size 600x600mm thickness 9 to 10mm 49.50 sqm

38 12.46 15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m).

12.46.2 Granite stone black 14.39 sqm

39 12.44 Extra for nosing in Granite stone for treads. 27.40 M

40 Amedment 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545:2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 295.02 sqm

41 Amedment 14.64 Providing and applying Premium plastic emulsion paint with roller application minimum three coats applied @ 0.75 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -1 Class D & C ( Glossy and Semi Glossy Finish) of required shade (Product such as Asian Apcolite Premium , Dulux Super Cover, Berger Easy Clean Nippon Breezee Metex Gold, Opus I-50 / Calista) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.(with 3 year Warranty) 141.12 sqm

42 Amedment 14.68 Providing and applying on exterior surface with PREMIUM Exterior emulsion paint of required shade to give protective and water proof finish minimum 3 coats applied @ 1.40 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D , C (Glossy /Semi Glossy finish ) (Product such as Asian Apex ,Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon Sumo Etra, Opus True flex) inclusive of providing abro tape on edges and articleand cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.(With 3Year Warranty.) 153.90 sqm

43 Amedment 14.72 Providing and applying Glossy finish Enamel paint mimimum 2 Coats in al surface applying @ 0.75 lit/ 10 Sqm up to required finish as per relevent I.S. code 2932: 2013 of (Product such as Asian Apcolite Premium Enamel Dulux Promise Premium Enamel Nerolac Synthatic Enamel, Opus Prime enamel ) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackle and labour etc. complete for the work. 142.52 sqm

44 RS 12.15 Cement art Mural work 59.21 sqm

ADD 9 % FOR ELECTRIFICATION

( B ) PARAPET WALL

45 3.4 Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 1.13 cum

46 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.2 Thermo-Mechanically treated bars FE 500 136.08 kg

47 2.1 Providing and fixing form work including centering, shuttering, strutting,staging, propping bracing etc. complete and including its removal at all levels, for:

47.1 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape 12.42 sqm

48 7.6 Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: 6.17 cum

49 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 34.92 sqm

50 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.4 In Cement Mortar 1:6 (1 cement : 6 fine sand) 44.84 sqm

51 Amedment 14.56 Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545:2021 (Product such as Birla wall care, Asian trucare,JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work. 79.76 sqm

52 Amedment 14.68 Providing and applying on exterior surface with PREMIUM Exterior emulsion paint of required shade to give protective and water proof finish minimum 3 coats applied @ 1.40 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D , C (Glossy /Semi Glossy finish ) (Product such as Asian Apex ,Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon Sumo Etra, Opus True flex) inclusive of providing abro tape on edges and articleand cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.(With 3Year Warranty.) 79.76 sqm

TOTAL ( B ) 0.00

TOTAL ( A + B ) 0.00

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

AS PER BUILDING S.O.R. 1.1.2015 & ROAD S.O.R. 1.1.2025

SN REF NO. ITEM DESCRIPTION QTY UNIT RATE AMOUNT

1 22.2 Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 10 km (earth measured in stacks will be reduced by 20% for payment).

2 22.3 Supplying and stacking sludge at site including royalty, loading, unloading and carriage upto 10 km (sludge measured in stacks will be reduced by 8% for payment). 60.63 cum

3 22.5 Rough dressing the trenched ground including breaking clods. 22.97 sqm

4 22.8 Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or / and good earth to be paid separately). 71.67 cum

5 22.9 Mixing earth and sludge or manure in proportion specified or directed. 71.67 cum

6 22.13 Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately). 49.59 cum

7 22.25 Providing and planting following herbs in garden including preparation of soil, base plantation, providing and spreading different fertilizers, soil and sand:

22.25.1 Hedges like Alife, Dorenta, Tikoma etc 1200.00 Each

22.25.2 Furn like Arica, China etc (3 year old) 521.00 Each

22.25.3 Hibiscus (Flower)/ Rose 800.00 Each

22.25.4 Carpet grass (well developed) 22.97 sqm

8 Road sor 12.6 Providing and planting of 3‟0” to 4‟0” heighted wasingtonia, filipheria/bismarkia novelist plam plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance. 30.00 Each

9 Road sor 12.7 Providing and planting of 4‟0” to 5‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance. 20.00 Each

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

EXTERNAL SANITATION & WATER SUPPLY WORK

S.No. SOR NO. Description Qty. Unit Rate Amount

EXTERNAL WATER SUPPLY

1 19.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete

1.1 19.6.1 15 mm nominal outer dia pipes 150.00 meter

1.2 19.6.3 25 mm nominal outer dia pipes 500.00 meter

1.3 19.6.6 50 mm nominal outer dia pipes 290.00 meter

2 19.16 Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end):

2.1 19.16.1 25 mm nominal bore 25.00 each

2.2 19.16.3 50 mm nominal bore 2.00 each

2 19.17 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

2.1 19.17.1 25 mm nominal bore 25.00 each

2.2 19.17.3 50 mm nominal bore 1.00 each

2 23.13 Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required. 100.00 each

ELECTRICAL SOR 2015

3 26.2 Supplying, installation, testing and commissioning of centrifugal type mono-block electric pump set for water supply system having following capacity three phase, 415 volts AC induction motor and pump including suitable channel iron base frame, suitable C.C. foundation and connection of suction and delivery line etc. as required.

26.2.3 7.5 HP, 650 LPM, 30 m head, suction size 80 mm, delivery size 65 mm 1.00 each

Total (A+B) 0.00

E.E. E.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

[ As per P.H.E.D -U.S.O.R 2020, AMENDMENT NO-07/2022-23 ]

S.No. Code No. Description Qty. Unit Rate Amount

1 28.1 Carrying out the resistivity survey by VES method using Schlumberger configuration for locating the proper spot with three soundings for drilling of tube well within the selected Habitation, including photography, interpretation of resistivity data and submission of report in the desired format along with resistivity readings, necessary graph andphotographs. 1.00 Per successful point

2 29.3 Drilling of perfectly vertical bore hole of a diameter suitable to receive 150 mm nominal diameter casing pipe upto desired depth below ground level inclusive of the labour charges for transporting, lowering and fixing of 150 mm nominal diameter and fixing of 150 mm nominal diameter M.S./ G.I. / U.P.V.C. casing pipe inside the bore hole including all works pertaining to drilling such as transportation, installation and removal of drilling machine etc.complete.

2.1 a) In all type of collapsible strata consisting of soils, clays, sand , moorum, gravel, boulders etc. 80.00 Mtr

2.2 b) In all types of rocks. 120.00 Mtr

3 29.9 Providing and fixing of well cap on top of the tube well for protection

C 150 mm dia. 1.00 each

4 29.10 Construction of concrete block over dry tube wells for protection of size 0.45m x 0.45m x0.45m in M-15 cement concrete mix complete work. 1.00 each

5 7 (page -356) ISI marked UPVC casing pipe Confirming to IS 12818/92 (with up-to-date amendments), Part C,General Note: 27.28.11

CM casing pipes, 150 mm dia

6 30.2 Labour charges for assembling, centering and lowering of properly designed casing pipe assembly inside the bore hole drilled for construction of Gravel Packed tube well including the cost of providing and fixing of centraliser, and transportation of casing assembly etc. complete .

e) Casing assembly composed of 150 m.m. dia. UPVC blank and screened pipes. 120.00 Mtr

7 34.18.1 Labour only for lowering of single phase submersible pumping set of capacity 1 to 3 HP in the tube well with flexible/ rigid pipe line assembly, electrical cable, nylone rope, testing etc. complete including connecting the electrical cable from pump & starter - Depth up to 150mtr. 1.00 Job

8 34.20.105 Supplying & Installation of Energy efficiant five star BEE rating ISI Marked required capacity single phase, 50 Hz, 220V, deep well submersible pump Stainless Steel body, suitable for 4"/6" tube well with Contral Panel Starter suitable for Submersible pump with dry run protection, connections, including clamps, bore cap etc. as required as per specifications but excluding pipe, SS / Nylon wire rope and connection cable.

(vi) 1.5 H.P. with up to 6 stages, Head Mt. 42-17 Discharge LPM 65-150 1.00 each

9 Electrical sor 2020 item no. 23.14 Supplying, laying and fixing following size submersible cable along with GI/PVC/HDFC pipe line or laid in ground etc as per specification and IS: 694 (2010). Note: Cable should be rust proof, safe from oil / Grease and under water Chemical / abrasion Resistant.

E.E. A.E. Sub. E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

CONSTRUCTION OF RCC DRAIN

AS PER ROAD S.O.R. 1.1.2025

S.N. REF PARTICULAR OF ITEMS QTY. UNIT RATE AMOUNT

1 3.19 ( b ) Construction of RCC open drain with width 0.60m or 0.45 m (inside dimension) and average depth from inlet to outlet 0.60m or 0.45 m (maintaing slope as per site conditions) with 120 mm thick RCC M-25 walls, 120 mm thick RCC M-25 bottom slab, over 100 mm thick (Av.) levelling course in PCC M-15 including Construction of RCC open drain with width 0.60m or 0.45 m (inside dimension) and average depth from inlet to outlet 0.60m or 0.45 m (maintaing slope as per site conditions) with 120 mm thick RCC M-25 walls, 120 mm thick RCC M-25 bottom slab, over 100 mm thick (Av.) levelling course in PCC M-15 including 300.00 Meter

2 3.27 Construction of RCC drain/cover slab/chamber

2.1 ii Construction of RCC drain/chamber/cover, placing in position, providing shuttering and concreting by using concrete mixer, compaction by vibration etc complete as per drawings and technical specifications excluding reinforcement, with RCC M-20 25.20 Cub

2.2 iii Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in drain/cover/chamber complete as per Drawing and Technical Specifications 2.02 MT

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

CONSTRUCTION OF SEPTIC TANK

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 25.20 cum

2 1.6.1 All types of soils 7.20 cum

3 1.17 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M. 2.72 cum

4 1.26 Carriage by mechanical transport upto 5 km lead:

1.26.1 Earth 22.48 cum

5 3.1 Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of form work.

5.1 3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). 1.20 cum

6 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size). 10.11 cum

7 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete:

3.12.1 Thermo-Mechanically treated bars FE 415 1010.80 kg

8 2.1 Providing and fixing form work including centering, shuttering, strutting,staging, propping bracing etc. complete and including its removal at all levels, for:

8.1 2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level. 26.16 sqm

9 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:3 (1 cement : 3 fine sand) 32.52 sqm

10 11.5 Neat Cement punning. 32.52 sqm

Amount of 1 units TOTAL 0.00

Amount of 2 units 0.00

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

S.No. Code No. Description Quantity Unit Rate Amount

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 207.94 Cum

2 1.6 Extra for every additional lift of 1.5 m or part thereof.

1.6.1 All types of soils 98.50 Cum

4 1.18 Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete. 7.30 cum

5 3.1 Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). 10.94 Cum

6 3.3 Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work.

3.3.1 M-20 Grade 45.10 Cum

7 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:

3.12.2 Thermo-Mechanically treated bars FE 500D 4239.21 Kg

8 2.1 Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level. 11.80 Sqm

9 2.1.8 Beams, lintels, cantilevers & walls 153.92 Sqm

10 2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ) 48.00 Sqm

11 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.1 In Cement mortar 1:3 (1 cement : 3 fine sand) 130.00 Sqm

12 9.6 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer.

9.6.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 271.60 KG

13 14.22 Painting on new work (two or more coats) to give an even shade with:

14.22.1 Satin synthetic enamel paint 4.68 Sqm

Total Of One Unit 0.00

Total Of Two Unit 0.00

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

LED GLOW SIGN BOARD

S.N. S.O.R. NO. PARTICULAR OF ITEMS Qty. Unit Rate Amount

1 ELE . SOR 6.58 Supplying, installation, testing and commissioning of Acrylic LED light (a) Specification of Acrylic 3 mm thick x 3 " width x 4 " depth *(imbose) (b) Specification of LED modules :- Each Moduel should have 6 Nos LED of 1 watt 90.00 Sqft

2 ELE . SOR 6.61 Fabrication and installation of angle iron including angle size 50 mm x 5 mm thick with labour charges including materials as per specification 315.00 Kg

3 ELE . SOR 6.62 Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work

6.62.1 4 mm thick 16.72 Sqm

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

EXTERNAL ELECTRICAL WORK

AS PER ELECTRICALE S.O.R. 2020

SN Sor No. Description of Item Qty. Unit Rate Amount

A 7.0 M. High Octogonal Electric Pole For Parking Area

1 19.7 Supply of hot dipped galvanized (in single dip to minimum 75 micron) octogonal pole made of 3mm thick steel grade E-350 sheet having window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications with 4 way terminal connector including 3mm thick anchor plate, 4 nos 20mm dia foundation bolts of EN8 grade, and as per IS 2062 & BS EN: 10025. (designed for wind speed upto 180km/hr, IS: 875 Part 3)

19.7.2 7 metre high, dia 130mm at bottom and 90mm at top, base plate size 220x220x12mm, foundation bolts 700mm long

2 19.12 Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as per specification.

Footing Size - 0.60 m. x 0.60 m. x 1.20 m. 8.64 Cum

3 19.11 Erection of GI octogonal/ tubular/conical pole on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position as per specification.

19.11.5 7 metre high 20 Each

4 19.27 Supplying and fixing of single over hang (Arm) 1500 MM (long)x50 mm dia decorative GI street light pole bracket made out of GI "A" Class pipe welded to 300 MM Long GI Pole canopy of suitable dia at angle of 102.50 Degree including having GI triangular stiffner and making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy including FRP Dome on existing pole etc. as per enclosed drawing and as per direction of engineer-in-charge. 20 Each

5 15.1 Supplying and laying following sizes one number FRLS PVC insulated/XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground at a depth not less than 40 cm and upto 90 cm including excavtion, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

15.1.23 4 x 16 sq. mm. 530 Metre

6 15.15 Supplying and laying following sizes one number FRLS PVC insulated, PVC sheathed, unarmoured, copper conductor control /power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as per specification and IS: 694 (2010).

15.15.1 2 x 1.5 sq. mm 180 Metre

7 15.28 Supplying, fixing and cramping suitable size and all type aluminium ferule/ lugs to following size 1.1 KV grade power cable core / lead, pressed with high pressure cramping tool including connection to switch gear/ MCCB etc as required.

15.28.3 16 sq. mm 20 Each

8 6.28 Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.

6.28.7 60 watt 20 Each

9 19.16 Supplying and fixing water tight terminal box made of 1.6mm thick M.S. sheet with detachable gland plate in bottom, hinged front open able cover, rubber gasket, having 1 Nos 4way connector and 1 No SPMCB inside the box for cable connection, fixed to pole with 2 Nos clamp made from 40x3mm M.S. flat with 2 No nut bolt dully painted with 2 coat of red oxide paint and 2 coat aluminium paint complete as per specification.

19.16.2 30x20x15 cms. 20 Each

10 9.14 Supplying and fixing TP MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

9.14.2 6 amps to 32 amps 2 Each

11 14.1 Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification.

14.1.1 63 mm outer dia and 50 mm Inner dia 530 Metre

12 7.19 Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification.

7.19.1 Upto 300 mm deep 0.90 Sqm

13 7.20 Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification.

7.20.1 Digital type 1 Each

14 10.18 Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification. 1 Each

15 10.23 Providing and fixing panel mounting digital type VAF (Volt-amp-frequency combined) Multi Function meter of size 100x100 (NS) in existing cubical panel including connection, testing and commissioning etc. as per specification. 1 Each

16 12.19 Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification:

12.19.1 With 3 metre long GI Pipes and 50 kg back filling compound. 1 Each

TOTAL ( A ) 0.00

E.E. A.E. Sub. E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

AS PER ELECTRICAL SOR 2020

SN SOR NO. Description of Item QTY Unit Rate Amount

1 6.54 Supplying , installation , testing and commissioning of low maintenance tubular battery with necessary connectors, links terminals etc. 12Volts DC 18 AH 1268.00 Each

2 6.55 Supplying , installation , testing and commissioning of photovoltic solar panels of 12 Volt 40 Watt as per the specifications 314.00 Each

3 6.56 Supplying , installation , testing and commissioning of solar frame for panel with suitable angle iron required 314.00 Each

4 6.57 Supplying , installation , testing and commissioning of Battery charger charging unit with battery overcharge protection, battery deep discharge protection, reverse polarity protection, etc. complete 1264.00 Each

E.E. A.E Sub.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

AS PER ELECTRICALE S.O.R. 2020

SR. Sor no. Description of items Unit Qty. Rate Amount

1 27.23 Supplying , installation , testing and commissioning of 64 Channel NVR 8 Sata port Up to 64 channel IP camera input , Max 320Mbps incoming bandwidth , Smart H.265+/H.265/Smart H.264+/H.264/MJPEG , Up to 12MP resolution preview and playback , Support 8 SATA HDDs up to 10TB each,1 eSata , 4 USB(2 USB3.0, 2USB2.0) , 2 HDMI / 2 VGA simultaneous video output ,ONVIF Version 2.4 conformance , Alarm In / out 16/6 , Two way talk 1 Channel Input, 2 Channel Output RCA , 1 RS485, 1 RS232 , 2 RJ-45 port (10/100/1000Mbps), Support ANPR Camera as per the specifications. 2 Each

2 27.13 Supplying , installation , testing and commissioning of 2 MP ANPR Camera Image sensor 1/1.9 CMOS , 2 MP 1920x1080 Lens 10.5~42mm , H.264/H.265/MJPEG , Frame Rate 50/60 FPS, WDR100dB, ANR,AWB, AE, Auto IRIS, Alarm in/ out , Traffic Counting Range 15~80 Mtr , 1RS232 serial Port , 2 RS485 port, , 1 GPS, IR Range of 100 MTR , SD Card 128GB ,,Number Plate snap, Support Traffic Flow , occupancy , heady , average speed , queue, length atatic embedded Integration component design , built in variety algorithm such as ANPR , traffic Data collection and analysis, vehicle type Classification , Traffic incidents detection , vehicle brand . 1 Ethernet Port (100/1000m) , Built in sunshade unit , IP66, AC220V , Mounting accessories as per the specifications. 4 Each

3 27.11 Supplying , installation , testing and commissioning of 4 MP Bullet Camera weather & dust proof IP based Fixed Lens day/night Camera (IP67 , IK 10) , 1/3” 4MP PS CMOS Image Sensor, H.265 and H.264 triple-stream encoding, WDR(120dB), Day/Night Support, UL ,CE FCC Certified as per the specifications. 22 Each

4 27.5 Supplying , installation , testing and commissioning of 2 MP PTZ Camera weather & dust proof IP based Dome PTZ (Pan Tilt & Zoom) true day& night camera ,1/2.8” 2MP PS CMOS Image sensor, Max. 50/60fps@1080P,Color: [email protected]; [email protected] (IR on), Powerful 30x (4.5~135 mm) Optical and 16x Digital zoom, WDR(120dB), 3D DNR, Day/Night(ICR),Defog, ROI, EIS, AGC, BLC, HLC, Support Starlight Function, Up to 300 presets, auto scan, 8 tour, 5 pattern, auto pan, Tripwire, Intrusion, Abandoned/Missing , Face Detection, Heat Map, IR Range of 200 Mtr., Max 300° /s pan speed, 360° endless pan rotation, Built-in 7/2 alarm in/out,Micro SD card 256GB, IP67, IK10, Support PoE+, UL, CE ,FCC certified as per the specifications. 4 Each

5 27.39 Supplying , installation , testing and commissioning of 8 TB Surveillance Hard disk drive Complete as required 4 Each

6 27.27 Supplying , installation , testing and commissioning of 8 Port Giga PoE Switch 10/100/1000 8 Port with 2 GigaJ 45 uplink, PoE switch ,AI Extend , AI Vlan as per the specifications. 8 Each

7 27.45 Supplying , installation , testing and commissioning of 6U Indoor Rack Wallmount 6U 450D With Front Glass Door Lock & Key 550 6U - loaded with cable manager + PDU + Fan complete as required. 8 Each

8 27.48 Providing installation testing and commissioning of 15U Indoor Rack Wallmount 15U 630D With Front Glass Door Lock & Key 550 15U - (Fan, cable manager, PDU included) complete as required. 4 Each

9 9.27 Supplying and fixing Low voltage (class -II) surge protection device (SPD) TP&N 440 volts, in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 4 Each

10 27.70.1 Supply, installation , testing and commissioning of add on item junction box installed with Mount frame inside for Krone 10 pair disconnection/disconnections module, Corrosion free impact resistant, water proof, mild steel stable and maintenance free with same size crone module as junction box. 20 Pair Juction box 8 Each

11 27.34 Supplying , installation , testing and commissioning of 24 Port Managable POE Switch 10/100/1000 24 Port Managed PoE Switch with 2 Giga RJ45 & 2 Giga SFP combo uplink, Power Budget250W as per the specificatons. 2 Each

12 27.49.3 Supplying, installation, testing and commissioing of following size LED Monitor, table/wall mount with inbuild speaker minimum 5Wx2,with minimum 1 No of HDMI and USB port including remote control, connecting cable, batteries, and all accessories, connection etc complete as per specification. 49 inch 2 Each

13 11.2.2 Supplying, installation, testing and commissioning following rating single phase in single phase out ON-LINE UPS including connection etc but without batteries as per specification. 3 KVA with DC bus voltage 72 V 2 Each

E.E. A.E. S.E. ARCHITECT

Ar. Rohit marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

ESTIMATE OF TRANSFORMER

AS PER ELECTRICAL SOR 2020

SN SOR NO. Description of Item QTY Unit Rate Amount

11 KV DP STRUCTURE

1 19.1.2 "H" beam steel pole 152x152x7x12 mm standard weight 37.1 kg /metre 22.00 metre

2 22.1.12 DC cross arm made of MS channel 100x50x5 mm @ 9.56 kg/m 40.00 Metre

3 20.6 Supplying and erection of angle/channel iron cross arms/ bracket/ other fitting of approved size and shape including drilling of holes for insulator pins, bolts and nuts etc as per specification. 70.00 kg

4 20.19 Supplying and fixing approved make 11 KV glazed porcelain disc type insulator with tension hardware on existing pole/ support/ cross arm channel as per specification complete: 3.00 Each

5 20.20 Supplying and erection of 11 KV gang operated air break switch on existing two pole structure with insulators and all other accessories complete including locking arangement as per specification. 1.00 Set

6 20.21 Supplying and erection of 11 KV D.O. fuse unit on existing two pole structure with insulators and all other accessories complete including locking arangement as per specification. 1.00 Set

7 20.22 Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as per specification. 1.00 Set

8 20.23 Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as per specification. 1.00 Set

9 20.32 Supply and erection standard ACSR (aluminium conductor steel reinforced) confirming to IS 398-1961 of approved make at existing insulator at height upto 14m from ground level including stringing, binding with insulator, jointing wherever required, jumpering, tearing off connection etc complete etc. as per specification including clearing off obstacle if any:

20.32.4 Raccoon 6/1/4.09mm dia with calculated aluminium area 78.83 sq.mm , weight 319 kg/ km (198 amps) 0.20 Km

10 20.33 Supplying and erection DANGER BOARD made MS sheet duly painted and maked as per IE rules and specification. 1.00 Each

11 21.1 Supplying and installation of outdoor type Transformer ONAN type with copper winding having following continuous KVA rating, 11 /0.415 KV, 3 Phase 50 Hz Vector group DYn-11, (Online tap changer) tapings in steps of ± 2.5%, ± 5%, --7.5% with oil conservator, silica gel breather having connecting terminals on HV side suitable for bare conductor/HT cable connection, cable end box on medium voltage side suitable for 1.1 KV single / 3½ core cable(upto 300 sq mm)/bus ducting arrangment and confirming to IS:1180 Part-2 Level 3, on existing double pole structure or Brick /CC/RCC platform with all fittings, accessories, filled with filtered transformer oil including testing and commissioning etc. complete as per specification

SAFETY EQUIMENTS

12 21.5 Providing and erecting floor mounted sand/ water bucket stand for keeping 4 nos. of fire bucket, 1500 mm in length and 900 mm in height made out of 30 X 30 X 4 mm angle iron welded with 4 hooks and duly painted with one coat of zinc cromate primer and 2 coat of synthetic enamel paint of post box red colour etc complete. 1.00 Each

13 21.6 Supplying G.I. Fire buckets with round bottom having at least 9 lit. capacity duly painted with one coat of zinc cromate primer and 2 coat of synthetic enamel paint of post box red colour and filled with dry sand and kept on provided wall hook or stand etc complete. 1.00 Each

14 21.8 Supplying and erecting chain link mesh fencing for electric sub-station switch yard of 2.5 m approx. height from ground level using angle iron size 50 X 50 X 6 mm erected in C.C. foundation 15 X 15 X 40 cm deep at every 2 metre fitted with flat iron support of size 25 X 6 mm on top, bottom and mid way and chain link mesh 50 x 50 mm aparture and 4 mm dia G.I. hard wire securing and screwing with 2mm dia G.I. wire, G.I. staples, G.I.U-nails or steel pins to the angle iron at every distance of 30 cms, by iron studs complete duly painted with one coats of red oxide and two coats of approved colour paint. (Area of fencing i.e. height x length is to be measured) 3.00 sqm

15 21.9 Supplying and erecting MS gate of approx. size 3.0 m (W) x 2.0 m (H) in two laps for electric sub-station switch yard fencing frame made of angle iron size 50 X 50 X 6 mm on top bottom and sides fitted with flat iron support of size 25 X 6 mm on mid way horizontaly and square bar of size 8 mm at every 100mm vertically including 3 sets of heavy duty MS hinges and aldrop complete duly painted with one coats of red oxide and two coats of approved colour paint. 1.00 sqm

16 26.17 Supply and erecting of following ISI marked Fire extenguishers on wall/ column including erecting bracket etc complete.

26.17.5 CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 4.5Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 55B. Complete with Hose Assembly and horn , locking arrangement, operation manual, bracket with two screw and sleeve 1.00 Each

17 24.17.2 ABC Fire Extinguisher 6KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 4A, 144B. With all accessories. 1.00 Each

18 21.3 Supplying, installation, testing and commissioning of following capacity diesel Generating Set (alternator directly coupled to diesel engine) compete in all respect broadly comprising of following and as per CPCB 2 norms (upto date ammended), including following specification. A. Alternator : Self excited, brush less type, of following capacity, 3 phase, 415 volts 50 Hz, 4 pole, AC alternator complete with all accessories.B. Engine : water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2 metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification.C. AMF Panel : Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches, meters and other accessories, internal wiring, connection, inter-connection etc. for trouble free smooth functioning of DG Set complete with battery charger and leads as per specification.D. Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as per specification.

19 Miscellaneous 1.00 Job

E.E. A.E Sub.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

EXTERNAL FIRE FITING WORK

AS PER BUILDING S.O.R. 1.1.2015

S.No. SOR NO. Description Qty. Unit Rate Amount

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 60.12 Mtr.

1 23.1 Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line.

2 23.2 Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation.

3 23.4 Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required.

23.4.2 100 mm dia 6.00 each

4 23.5 Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/ Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required..

23.5.2 100 mm dia 4.00 each

5 23.11 Providing and fixing pressure switch with suitable for 1-10 Kg/cm2 including 12/15 mm Ø isolation valve, G.I. nipple, elbow, electrical connections setting of Cut-In and cut-Off pressure complete in all respects and in an approved manner. 4.00 each

6 23.12 Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner. 4.00 each

7 23.18 Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

HYDRANT VALVE 13.00 each

8 23.22 Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

RRL hose pipe 23.00 each

9 23.24 Supplying & fixing 63 mm dia Stainless Steel IS: 3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzle conforming to IS: 903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

branch pipe 15.00 each

10 23.25 Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required.

23.25.2 Size 900 mm x 600 mm x 500 mm 15.00 each

ELECTRICAL SOR 2015

11 26.2 Supplying, installation, testing and commissioning of centrifugal type mono-block electric pump set for water supply system having following capacity three phase, 415 volts AC induction motor and pump including suitable channel iron base frame, suitable C.C. foundation and connection of suction and delivery line etc. as required.

26.2.3 7.5 HP, 650 LPM, 30 m head, suction size 80 mm, delivery size 65 mm 1.00 each

Total Of External Fire Fighting Work 0.00

E.E. A.E. S.E. ARCHITECT

Ar. Rohit Marathe

DETAIL ESTIMATE OF PROPOSED 500 SEATER NALANDA PARISAR

Add 18% Gst For Road Sor Items & PHE Sor Items

SN ITEM DESCRIPTION AMOUNT 18% GST

1 CC ROAD 0.00 0.00

2 LANDSCAPING 0.00 0.00

3 BORE WELL 0.00 0.00

4 CONSTRUCTION OF RCC DRAIN 0.00 0.00

5 MS GRILL BOUNDARY WALL 0.00 0.00

E.E. A.E. SUB.E. ARCHITECT

Ar. Rohit Marathe

SR. Description of items Qty. Unit Rate Amount

Tensile Work Detail : Arc 58 * 2.50 mm Perling 58 * 2.50 mm Fabric 750 gsm 10 year warenty Inc. Civil work & 18% Gst 288.00 Sqm

E.E. A.E Sub.E. ARCHITECT

Ar. Rohit Marathe