PROVN OF LOW SECURITY WALL WITH BARBED WIRE FENCE AROUND FOL DUMP AREA UNDER GE TAWANG.

Amount

Excavating in trenches not exc 1.5m wide and not exceeding 1.50m deep, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches not exc 1.5m wide and exceeding 1.50 m and not exceeding 3.00 m deep, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for Plain cement concrete (1:4:8) type D-2, using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metres and depositing where directed a a level nexc. 1.5 metre above the starting point complete all as specified and directed.

M&L for formwork to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam ; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished square, rectangular or polygonal surfaces of concrete complete all as specified and directed.

M&L for formwork to faces of sides and soffits of floor or roof beams, cantilevers, shelves including supports, overhangs,etc for rough finished flat surfaces of concrete complete all as specified and directed.

M&l for Reinforced cement concrete (Design Mix) M-25 using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc; basement slabs under-reamed pillars and mass concrete complete all as specified and directed. (Note : Steel reinforcement shall be measured & paid separately.)

M&L for Reinforced cement concrete (Design Mix) M-25 using 20mm graded crushed stone aggregate as in column, Pillars, piers, post and struts complete all as specified and directed. (Note : Steel reinforcement shall be measured & paid separately.)

M&L for Reinforced cement concrete (Design Mix) M-25 using 20 mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed. (Note : Steel reinforcement shall be measured & paid separately.)

M&L for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

M&L for TMT bars 8 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (20mm graded agg) as in precast block masonary with solid blocks, exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

S&F Mild steel work of angle iron or flat iron etc for railings, balusters, nosing to steps including embedding in concrete and screwing etc, flat iron for posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc & similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S&F PVC (SWR) pipe single socketed 110 mm bore in any length with rubber ring joints, laid in trenches or in floor, complete all as specified & directed.

M&L for Plain cement concrete (1:2:4) type B-1, using 20 mm graded crushed stone aggregate as in coping including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar (1:4) on fair faces of brick or concrete surface finished fair and even complete all as specified and directed.

M&L Two coats of cement base paint over a coat of white wash including preparation of newly plastered surfaces of walls complete all as specified and directed.

S&F Galvanized, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rail straining bolts, including securing or tying at crosings with and provision of galvanized mild steel wire, staples or steel pins, etc, as directed (each line wire to be measured) complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

SHELLUNG CONSTRUCTION

M/S ARUNACHAL VIKASH

M/S ACE BUILDERS

M/S L G BUILDERS

SHAMBHALA TRADERS

M/S GLOBAL ROYAL CONSTRUCTION

M/S RHEGON CONSTRUCTION

M/S RINCHIN DORJEE CONSTRUCTION

M/ S N T ENTERPRISES

M/S K D CONSTRUCTION