PROVN OF ENTRY GATE AT THIMMAYA MARG AND PROVN OF TOILETS NEAR MANDIR COMPLEX BLDG NO P-150 OF CENTRAL COMMAND SIGNAL REGIMENT NDER GE (WEST) LUCKNOW

Amount

Surface dressing not exc 15 cm deep in Soft/ Loose soil complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and not exc. 1.5m in deep for foundation etc or for shaft , well cesspits, manhole,pier holes etc n exc 10sqm on plan and n exc 1.5m depth and getting out in soft/loose soil including framing bottom surfaces for laying cables (if applicable) complete all as specified and directed

Excavating in trenches, n.exc 1.5m wide & n.exc 1.5m in depth; for foundation, laying of sewage pipe line, manholes etc n.exc10 sqm on plan & n.exc 1.5 m in depth & getting out in hard & dense soil complete all as specified and directed

Excavation in trenches exc 1.5m but & n.exc 3.0m depth for foundation, etc. or for shafts, wells, cesspits, manholes, etc. not exc 10 Sqm on plan and not exc 1.5 m depth & getting cut in soft/loose soil complete all as specified.

Surface excavating not exc 30 cm deep and averaging 15 cm deep and getting out soft / loose soil complete all as specified and directed

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm in soft/loose or hard/ dense soil complete (after laying of cables if applicable) complete all as specified and directed

Earth filling under floor including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified and directed

Removing excavated material surplus soil to a distance exc 50m - 250m and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed.

M&L plain cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregates) as in foundations, filling and mass complete all as specified and directed.

M&L for brick work with fly ash brick straight or curved on plan exc 6 mtr mean redius built in CM 1:6 complete all as specified and directed

M & L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 to any radius complete all as specified and directed.

M & L 40 mm thick Damp proof course in cement concrete 1:2:4 ty B-0 to horizontal or vertical surfaces incl necessary form work incl incorporating integral water proofing compound in the manner specified by the manufacture and in the proportions indicated complete all as specified and directed.

Supply only liquid water proofing compound, ISI Marked complete all as specified and directed

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and directed

M&L for polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm complete all as specified and directed

M&L for 100 mm thick PCC 1:5:10 type D-2 using 40mm graded stone aggregate for filling in floor complete all as specified and directed

M&L for 25 mm thick Cement concrete PCC 1:2:4 type B-1 (using 20 mm graded granite stone aggregate) in sub base of flooring complete all as specified and directed

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors joints free, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and as directed.

M&L providing glazed ceramic tiles coloured 300x450x6mm thick in vertical surfaces like dado etc set and jointed in neat cement paste and pointed in coloured cement to match over 10mm thick cement plaster in CM 1:4 complete all as specified and directed

M&L for hardcore of broken stone boulders gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled / rammed to a true surface etc complete all as specified and directed

M & L for 75 mm thick PCC 1:3:6 type C-2 (using 20 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels n exc 3 mtr long complete all as specified and directed

M & L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splay between floors and beams, etc. and similar works for rough finished surfaces complete all as specified and directed.

Formwork to edges of concrete flats treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm width rough finished surface of concrete complete all as specified and directed

Formwork to chullah hoods, cha?jjas, troughs and similar items in?cluding edges rough finished of concretecomplete all as specified and directed

M&L for form work flat, rough finished surface of concrete for side of footing coloumns plinth beams or similar work including any types of supports/scafolding etc complete all as specified and directed

M&L for form work to polygonal, rough finished surface of concrete for side of coloumns above GL, lintel beams, chajja, soffits of suspended roof slab and roof beams or similar work including any type of supports/scafolding etc complete all as specified and directed

M&L for form work to edge and soffits to arches, rough finished surfcaes of concrete, suspended roof slab and roof beamns or similar work including any type of suports/scafolding etc complete all as specified and directed

M&L for form work to sides and soffits to domes, vaults, shell roofs and arch ribs, rough finished surface of concrete or similar work including any type of supports/scafolding etc complete all as specified and directed

M & L reinforced cement concrete (nominal mix) type A-1 1:1.5:3 (20 mm graded aggregates) in Beams, cantilevers, bressumm ers, lintels over 1.5m span the like complete all as specified and directed.

M & L reinforced cement concrete (nominal mix) type A-1 1:1.5:3 (20 mm graded aggregates) in chajjas complete all as specified and directed.

M & L reinforced cement concrete (NOMINAL mix) type A-1 1:1.5:3 (20mm graded aggregates) in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC design mix (M-25) using 20 mm graded stone aggregate for foundation footings plinth beams, cloumns up to GL etc all as specified and directed by Engineer -in-charge. Note Reinforement shall be measured and paid seperately under relevent item complete all as specified and directed

M&L for RCC design mix (M-25) using 20 mm graded stone aggregate for coloumn above GL, lintel beam, chajjas, roof beam and slab or similar suspended work etc complete all as specified and directed. Note: Reinforcement shall be measured and paid separatly under relevant items.

M&L for plain Cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregates) such in benching, coping, bends slope bed block drain and surface channel and the like, rounded or chamfered on edges including necessary formwork and demolition of existing concrete of any description and removal of debris out off the premises complete all as specified and directed.

M&L for Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings,chajjas drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends complete all as specified and directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Ditto, but 6mm to 8 mm dia complete all as specified and directed.

.-Ditto as in item above here in above but 5 mm dia and over upto and including 10 mm dia in stirrups spacers and binders (For footings & plinth) complete all as specified and directed

M&L for rendering 10 mm with W.P.C as per manufacturer instruction over green concrete on roof surfaces in cement mortar 1:3 finished even &smooth n with using extra cement complete all as specified and directed

M&L for rendering 15 mm thick on brick work/ concrete surfaces in cement mortar 1:6 finished even &fair n with out using extra cement complete all as specified and directed

M&L rendering 15mm thick in cement plaster 1:4 on surfaces even & fair n with out using extra cement complete all as specified.

M & L for 10mm thick in ceiling rendering in CM (1:3) finished even and fair (without using extra cement) complete all as speciified and directed.

M&L three coat of white wash on walls including preparation of new plastered surface complete all as specified and directed

All as per item No. 44 above but, on ceiling complete all as specified and directed

M&L for preparation of new plastered surfaces of wall and applying 3 mm thick wall care putty complete all as specified and directed

M&L for applying two coat of weather proof exterior emulsion paint over a coat of primer on new or old surface of wall complete all as specified and directed

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm mprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 mm2 and resistance to spread of flame of Class A category with property of being mite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: 1. For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made 2. M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid both side decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, and 4 nos stainless steel butt hinges and necessary S.S screws complete all as specified and directed

S & F 200mm long M.S cromium plated barrel tower bolts of extruded section complete all as specified and directed.

S & F stainless steel Butt hinges 100mm size complete all as specified and directed

S & F M.S cromium plated handle fabricated type 150mm long complete all as specified and directed

S&F 250 mm long MS Cromium plated sliding door bolt with hasp, staple bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed

S&F in 1500mm mild steel , ordinary pattern springs including roller and roller plate complete all as specified and directed

S&Fof framed work such as grills gratings etc with ends of bars shouldered and/or riveted, for forged into spikes; framed guard bars; and extra for portions framed , including pintle hinges, stops hand -made sliding bolts and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed

S & F stainless steel wire cloth (G-304) 0.36mm minimal dia of wire and average width of aperture 1.4mm fixed with stanless steel staples to windows complete all as specified and directed

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

M&L for galvanized steel water tubing medium grade of 25 mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and directed

S&F rotational moulded polethylene water tank of 500 ltrs capacity ( cylindrical vertical with closed top) noticed and portion all as pacific SSR Part- I complete all as specified and directed

S&F ball valves of PTMT high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20mm bore pipe complete all as specified and directed

S & F 20mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe fixed complete all as specified and directed

S&F vitreous china wash down water closet pan English type ( Pedestal Pattern) white including connection to drain(or out going pipe) & flushing pipe, anti syphonage pipe etc. complete including making good to floor complete all as specified and directed

S&F in repair Vitreous China squatting pan of orissa pattern, size 580x440mm white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern ( including fixing of flush pipe) including provision of cement concrete bedding complete all as specified and directed

S&F vitreous china wash basin, white flat back size 580 x 450 mm excluding taps, waste, chain and plug and porcelain stopper including a pair of standard mild steel bracket complete all as specified and directed

Supply only dual type capacity PVC flushing cistern low level with inlet, ball valve float chain and pull and brackets, flush pipe of polyethylene of low or high density or fixing PVC 32mm dia for low level cistern complete all as specified and directed

S&F CP health faucet (with 1.50 mtr tube) fixed to Angular Stop Cock and complete wall hanging arrangement complete all as specified and directed

S&F vitreous China urinals, bowltype (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed

S&F urinal spreader of C.P any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed

Supply & Fixing copper alloy long body bib taps half turn suitable for 15mm bore pipe with capstan head complete all as specified and directed

Supply & Fixing pillar taps cast copper alloy chromium plated ,screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts screwed for iron pipe (bore of pipe 15mm) complete all as specified and directed

S&F PVC connection 15mm bore length not less than 450 mm long with both ends PTMT nuts complete all as specified and directed

S & F 15mm dia CP angle valve with cromium plated quarter turn of superior quality fixed complete all as specified and directed

S & F superior quality CP brass towel ring 200mm dia, fixed as in complete all as specified and directed

S&F grating doom 100mm of CP complete all as specified and directed

S&F 600mmx450mm bevelled edges mirror consisting of 5.5mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer complete all as specified and directed

S&F Toilet paper holder complete all as specified and directed

S&F CP soap dish, any type, fixed toplugs with chromium plated complete all as specified and directed

M&L Cast iron floor trap 100 mm dia grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed

S&F 110mm bore PVC (SWR) bend any radius and jointing to waste pipe complete all as specified and directed

M&L for 75mm thick plain Cement concrete (1:4:8) type D-2(using 20mm graded crushed stone aggregates) in foundation fillings and mass concrete complete all as specified and directed

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes 1:4 complete all as specified and directed

S & F Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors With grey cement and pigments complete all as specified and directed

M&L for PCC 1:4:8 type D-2 as in Concrete bed to drain pipes 150 mm bore ( Internal dia ) including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for Reinforced concrete pipes 150 mm bore ( Internal dia ), class NP2, laid and jointed complete with collars complete all as specified & directed. Note : WPC shall be measured and paid separately

M&L for Precast cement concrete Type B1 (1:2:4) in cover slabs of manhole, drains & similar articles set in cement mortar 1:6 including demolition of existing cover slabs of any description and removal of rubbish out off the premises complete all as specified and directed. Note: Reinforcement shall be measured and paid separately

On site LLDPE septic tank CONVENTIONAL type designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connectionetc., complete for 10 users complete all as specified and directed

Soakage well 1.2 M dia X 4.5 M effective depth excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats complete all as specified and directed

S&F , dholpur stone clading gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area not exceeding 0.5 sqm fixed with and including on number SS clamps (grade -202) of flat 30 mmx2mm, 50 mm long made to shape in each slab making V groove at top and bottom of stone and drilling hole for hold fasterner, polishing dholpur stone dust 1:1 complete all as specified and directed

S&F stainless steel/CP Brass letter or figure (not less than 2.5mm thick) (Block, Roman Italic or Indian) size 300 mm long x 50 mm width) etc including fixing complete all as specified and directed.

M&L for 20 mm thick granite table rubbed and polished as required fixed on pilars over 15 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for mild steel framed structural work as in doors or gates of angle or ther section with gusset plates, rairls braces etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or slinding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing of Fe-410-0 (Gde E- 250 complete all as specified and directed

M&L for preparation of new surfaces of steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified and directed

Demolation of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any motar etc complete all as specified and directed

M&L 75mm thick cement concrete type C2, 1:3:6 (40mm graded stone aggregate) as in sub-floors, sub-bases, etc complete all as specified and directed

M&L machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80 mm thickness, M-35 grade with grey cement and pigment etc complete all as specified and directed

M&L sand filling under floors or in foundation including watering and consolidation etc all as specified and directed.

M&L Exterior tile 30 cm x 30 cm x 25 cm thick set and jointed and pointed in neat cement slurry with grey cement and pigment in floors including 20 mm screed bed in CM 1:6 complete all as specified and directed

M&L, Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes (with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core F.R.L.S. cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:-(NOTE: Switch and socket to be measured and paid for separately):- (a) One light/fan point controlled by one switch

All as item No 102 above but on the same board with other switch complete all as specified and directed

All as item No 102 above one socket outlet point 5 Amp on an independent board complete all as specified and directed

All as item No 102 herein before but using 2.5 sqmm , PVC insulated, stranded copper conductor single core cable for one 3 pin 15/20 Amp socket out let point on an independent board complete all as specified and directed

S & F switch piano flush button single pole one way 5 Amp 240 volt complete all as specified and directed

S & F switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed

S & F socket outlet flush type multipurpose 2 in 1 , 3 pin 5 and 15 Amp, 230 volts complete all as specified and directed

S & F socket outlet flush type 5 pin 5 Amps 240 volts complete all as specified and directed

S & F ceiling rose surface bakelight two to three terminal complete all as specified and directed

S&F angle type holder insulated body with back plate suitable for batten fittings complete all as specified and directed

Supply and fixing in repairs LED lamp 7/9 watt, complete all as specified and as directed.

Supply and Fixing wall/surface mounting luminaires integrated LED Batten 20 W, 6000 K,120 lumens/watt , 230V with extruded Aluminium housing 4 feet long with frosted PMMA/PC diffuser & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements complete all as specified and directed

S&F in repair LED Building security light 24/25 Watt with high power LED source (>120lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 1.20 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts complete all as specified and directed

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V ,120 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements complete all as specified and directed

S&F in replacement sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way 240 Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB SPN 32 to 63 Amp 240 volts 10 KA breaking capacity complete all as specified and directed

S&F MCB SP 10 to 32 Amp 240 volts 10 KA breaking capacity complete all as specified and directed

Supply and fixing of heavy duty metal body exhaust fan single phase 230/240 volt of size 300 mm sweep including holes of suitable size grouting of nuts and bolt etc and making good to match the existing surface including louvers and making connetion with twisted copper flexible wire 23/0.076mm, including disconnecting and taking down old unserviceable exhaust fan and deposited in AGE E/M (W) store yard for BER action complete all as specified and directed.

M & L for Earthing complete with glavanised steel earth plate elactrode 600x600x6 mm thick buried directly in ground with top edge of the plate not less 1.5 mtr deep below with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut , bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber , reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate no 5 of MES SSR Pt-I 2009 print and complete all as specified and directed

M&L for sand cushioning to UG cables (8 cm deep before laying of cable and 15cm deep over the cable) complete all as specified and directed

Supply & Laying sub class `B’ bricks old sizes over the HT/LT cable laid flat for protection of cable complete all as specified and directed

M&L cutting PCC/floor/road and taking out cable and making good, including material as per existing after laying of pipe for cable protection all as specified and directed size of trench not more than 0.30 x 0.30 cm complete all as specified and directed

M & L for galvanised steel tubing 50 mm bore light grade laid in trenches, road crossings pole/wall etc. for cable protection including providing MS flat iron 50mm x 6mm clamps (02 Nos) complete all as specified and directed including taking down the existing UNSV steel tubing complete all as specified and directed

S & F GI pipe light grade', 40 mm Bore dia including all fithings laid in trenches or fixed on wall floor /trenches etc complete all as specified and directed

S & F GI pipe light grade', 25 mm Bore dia including all fithings laid in trenches or fixed on wall floor /trenches etc complete all as specified and directed

M & L Gun metal globe or gate valve with iron wheel head, screwed both hands from iron pipe and fix complete fitting of size 40 mm dia with ISI marked conf to IS 778,class - I complete all as specified and directed

M & L Gun metal globe or gate valve with iron wheel head, screwed both hands from iron pipe and fix complete fitting of size 25 mm dia with ISI marked conf to IS 778,class - I complete all as specified and directed

M & L for Cutting Steel iron/GI pipes size 40 to 50 mm dia and in position insertion of new tees, branches, etc complete all as specified and directed

M&L cutting PCC/floor/road and taking out cable and making good, including material as per existing after laying of pipe for cable protection all as specified and directed size of trench not more than 0.30 x 0.30 cm complete all as specified and directed

M&L for Brick masonary valve pit of size 0.450X0.450X0.900mtrs (internal dimensions) including excavation and earh work in any type of soil,plastering all walls surfaces internally and flush pointing to brick work externally as the work proceeds complete including angle iron 40x40x6 mm frame work,MS sheet cover 3mm thick ,handle , locking arrangement and painting complete all as specified & directed.(For 40 mm Gate valve)

SITC of Round shape architectural WARM WHITE LED Linear with housing Die-cast aluminium alloy - ADC12. The luminaire shall be suitable in size and aesthetically good view as approved by EIC. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°. The bracket shall have locking mechanism to fix & secure the desired tilt angle. The luminaire shall have silicon gasket between optical cover & LED chamber to ensure proper min. IP66 protection. if required the luminaire should have a breather gland.The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 8°to 40° beam angle and as per site requirement with the approval of Engg. In-charge & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 and above rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The fixture shall come with power & DMX cable loop in & loop out of minimum 750mm length. The fixtures shall be installed with have min. IP67 connectors. The luminaire shall have system wattage not exceeding 25W and system lumen output of not less than 875 lumens. Fixture shall operating temperature range of -10°C to 50°C. The fixture shall have an integral driver with input voltage for 220-247 VAC, 50/60Hz. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White to produce 16.7million colours. The luminaire shall be capable of digital dimming of 65536 steps. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables. Certifications :-CE, BIS ,RoHS,

SITC of Round shape architectural WARM WHITE LED flood light with housing Die-cast aluminium alloy - ADC12. The luminaire shall be suitable in size and aesthetically good view as approved by EIC. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°. The bracket shall have locking mechanism to fix & secure the desired tilt angle. The luminaire shall have silicon gasket between optical cover & LED chamber to ensure proper min. IP66 protection. if required the luminaire should have a breather gland.The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 8°to 40° beam angle and as per site requirement with the approvel of Engg. In-charge & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 and above rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The fixture shall come with power & DMX cable of minimum 750mm length. The fixtures shall be installed with have min. IP67 connectors. The luminaire shall have system wattage not exceeding 80 W and system lumen output of not less than 3900 lumens. Fixture shall operating temperature range of -10°C to 50°C. The fixture shall have an integral driver with input voltage for 220-247 VAC, 50/60Hz. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White to produce 16.7million colours. The luminaire shall be capable of digital dimming of 65536 steps. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables. Certifications :-CE, BIS ,RoHS,

SITC of Round shape architectural WARM WHITE LED flood light with housing Die-cast aluminium alloy - ADC12. The luminaire shall be suitable in size and aesthetically good view as approved by EIC. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°. The bracket shall have locking mechanism to fix & secure the desired tilt angle. The luminaire shall have silicon gasket between optical cover & LED chamber to ensure proper min. IP66 protection. if required the luminaire should have a breather gland.The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 8°to 40° beam angle and as per site requirement with the approvel of Engg. In-charge & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 and above rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The fixture shall come with power & DMX cable of minimum 750mm length. The fixtures shall be installed with have min. IP67 connectors. The luminaire shall have system wattage not exceeding 50 W and system lumen output of not less than 2400 lumens. Fixture shall operating temperature range of -10°C to 50°C. The fixture shall have an integral driver with input voltage for 220-247 VAC, 50/60Hz. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White to produce 16.7million colours. The luminaire shall be capable of digital dimming of 65536 steps. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables. Certifications :-CE, BIS ,RoHS,

Supply and Fixing of surface mounted , exterior rated , compact sized architectural light edge lighting . Robust , mechanical unique design . In RGBW and DMX controllable Unique 3*90 degree optional distribution . Robust Design and IP 66 . Adjustable -5 degree to + 85 Degree tilting angle . Wiring rqeuired for Data and Power seperately with IP 67 connectors. Dimensions 181*62*51 MM, Life 50000 Hrs L 70 at 35 degree, Die cast Aluminium Housing , electrostatically polyster powder coated , Drak grey color , anti UV PC lenses , clear tempered glass , Wgt .85 kgs , CRI 80 , white SDM 80 , IP 66, IK 06 as per CB , CQC, Max power 10 watts .Certifications :-CE, BIS ,RoHS,

SITC of Outdoor water proof Ip 67 Power supply 320watts complete all as specified and directed

Supply , Installation and testing of Panel 8 KVA 3 Phase & Servo MCB 6-32 amp 12 pcs , 32 amp TPN 10 KA 1 pcs complete all as specified and directed

Installation of GEL EARTHING with GI Strip to earthing along with existing cable as per ISI marks complete all as specified and directed

Supply and laying of 2.5 Sq mm 3 core PVC insulated unarmoured copper cable complete all as specified and directed

Supply and laying of 4 Sq mm 3 core PVC insulated unarmoured copper cable complete all as specified and directed

Supply and Laying of PVC pipe 25 MM complete all as specified and directed

Supply and Laying of PVC pipe 32 MM complete all as specified and directed

Supply and laying with 32 MM GI pipe ISI marks complete all as specified and directed

Supply & Laying or passing through pipe, 1100 volt grade heavy duty cable with XLPE insulated Aluminum condector served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of 16 Sq mm 2.0 core stranded condector nominal cross section complete all as specified and directed

Supply and laying 16 * 4 Core armoured aluminium complete all as specified and directed

Supply and fixing IP 65 boxes complete all as specified and directed

Gaurav Enterprises (BID ID -3446845)

Spectrum Enterprises (BID ID -3448526)

M/s Bajpai Constructions (BID ID -3446942)