REPAIR MAINT OF LEAKAGE AND SEEPAGE IN ZONE B AREA AND CENTRAL AMENITIES AT SEVOKE ROAD MIL STN UNDER GE SEVOKE ROAD

Amount

Demolition of cement concrete in ground floors and paving n.exc 15 cm thick (below or above ground level) unreinforced copmlete all as specified and directed

M&L for Providing 30 mm thick PCC 1:2:4 type B-0, (using 12.50 mm graded stone aggregate) as in Leveling course over RCC roof surface to achieve required slope including making rounded or chamfered on edges, mixed with WPC @2% by weight of cement, complete all as specified and directed Note : WPC shall be measured and paid separately as supply only.

M&L for 50 mm thick, PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as sub base of flooring complete all as specified.

Supply only water proofing compound (integral) complete all as specified and directed.

Roughening surfaces of existing roof treatment and taking out old APP membrane and removing from site including cleaning and washing down with water to remove dust etc complete all as directed.

M&L for providing, laying water proofing treatment over plastered surfaces of RCC roof shall be as under:- (a) The dried plastered surface of slab shall be painted with one coat of bituminous primer @0.4 liter/Sqm. (b) Over the primed surface a layer of APP based polymeric membrane minimum weight of 3 kg/sqm of approved manufacturer minimum 3mm thick, reinforced with polyster non woven fabric (weighing not less than 160gms/sqm) shall be laid by torch application method. The side over laps of membrane shall be minimum75mm and the end laps shall be minimum 100mm and sealing all overlaps and joints shall be done as per manufacturer's instruction . (c) The finished surface shall be given Aluminium paint @ 0.11 Kg/Sqm on APP as per manufacturer's instructions. Make:-M/S TEXSA INDIA LTD (MOPLY-FP) / M/S STP LIMITED (SUPER THERMOLAY) / IWL INDIA LIMITED (HYPERPLAS)/M/S Tiki Tar Danosa (India) Pvt Ltd (Hydro Stop)/M/s Supreme Bituchem India Pvt Ltd (Super Shield)

M&L for 10mm thick rendering in CM (1:4) over RCC roof surface to receive roof treatment finished even and smooth without using extra cement mixed with water proofing compound as per manufacturers instruction (WPC shall be measured and paid separately).

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling timber scantling 40sqcm and over in section unframed work in any position.

S&F rolled mild steel sections as in roof truss any type including hollow section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint on newly primed steel surfaces exceeding 10cm in width or girth complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness in roofs complete all as specified.

Dismantling asbestos cement (corrugated , semi corrugated , etc ) sheets in roof coverings complete all as specified.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Taking down cement plaster on brick wall/concrete surfaces etc including racking out joints hacking for key scrubing down with water etc of any thickness including Dado any description complete all as specified and as directed

M&L for 15mm thick rendering on other than fair faces of brick or concrete surfaces in CM 1:6 finshed even and smooth without using extra cement complete all as specified.

M&L for 20 mm thick rendering in CM 1:4 in two layers of 10mm each using water proofing compound in top layer only including finishing the surface even and fair(WPC shall be measured and paid seperately) complete all as specified and as directed

M&L for rendering 5 mm thick in CM 1:3 as in ceiling finished even and smooth without using extra cement complete all as specified..

M&L for preparation of new plastered surface and applying two coats of cement base paint over one coat of primer on wall etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white washing complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer and one coat of wall putty complete all as specified and directed. .

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with sub class 'B' bricks using old size bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified.

M&L for brick work with sub class "B" bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

M&L for cement concrete 1:2:4 Type B-1 using 20 mm graded crushed stone aggregate as in surface channels and drains, including necessary formwork complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms moulds, mitred/stopped ends etc.

Demolition of reinforced cement concrete work of any description and in any position not otherwise specifically provided for all as specified.

M&L 10mm dia and over mild steel TMT bar cut to length bent to shape required including cranking, bending and binding with mildsteel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed.

M&L mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Use and waste formwork to chullah hoods, slab , chajja, troughs and similar items including edges for flat

M&L for RCC 1:2:4 type BI (using 20 mm graded stone aggregate) nominal mix as in fins, facias,chajja,lintel etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded mechanically crushed stone aggregate) 75mm thick as in plinth protection/footpath, surface to be finished even and smooth without using extra cement including laid in alternate bays and joint to be filled with bitumen filler complete all as specified

Surface Preparation:- Remove all surface laitance and contamination free from loose aggregate or other sharp protrusions with fairly smooth finish by wire brush and grinding method and surface shall be damped with water for application of Brush bond waterproof coating.

PU Injection:- Injecting a two part liquid polyurethane like Nitofill WS60/ Nitifill UR63 of Fosroc or equivalent. The grout should be reacts rapidly with water to form a foam barrier using a suitable grout pump after drilling for installation of packers, sealing the crack with some epoxy adhesive as per manufacturer instruction or as directed by the engineer in charge. After injection the packer need to be removed and seal the same with some epoxy morter. Cost inclusive of drilling, injecting, packers and whatever adhesive required for injection.

Application of Nitocote CM210:- Providing and applying Nitocote CM210, an elastomeric cementitious coating approved under the UK WBs (WRC Listed) Scheme No. 0510522 upto a thickness of 1mm. The cured coating, after immersion , shall be capable of withstanding cracked substrate cyclic movement from 0-300-0 microns at 15 degree C for 6,000 cycles without failure. It shall have the capability to resist a positive water pressure of 5 bar as per DIN 1048, Pt 5 and a negative water pressure of 2 bar when tested to ITM/FTM-181. The cured coating , shall have the capability to static crack accomodation 0.9mm with Abrasion resistance as per ASTM D4060: Wear Index (equivalent to 40 N conc.) with CO diffusion resistance (Taywood method) > 50 m. Application should be as per Fosroc methodology. Note for item No 34, 35 & 36 : Whole work shall be executed under the directly supervision of OEM and company shall render certificate for correctness of Treatment

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed

M&L for 15mm thick screed bed or bedding layers for layng floor tiles etc in cement mortar 1:6 complete all as specified and as directed.

M&L for 10mm thick rendering in cement mortar 1:3 on other than fair face of brick work for laying tiles in vertical surfaces complete all as specified and as directed.

M&L for glazed coloured ceramic tiles of size 450mm x 300mm x 7- 8mm thickness in vertical surfaces set and jointed in neat cement slurry and pointed complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles of size 300x300x7 to 8 mm thick as in floor set and jointed in neat cement slurry and pointed complete all as specified and directed.

M&L for Double Charge Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm (200 x 1200 mm), in floors including etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in light shade all as specified and directed.

M&L for Double Charge Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed.

All as per item No 43 above but in skirting.

M&L granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

S & F in repair stainless steel tubular drapery rod 28mm dia as per sample kept in GE Office complete as specified and directed.

S&F stainless steel brackets for drapery rod 28mm dia as per sample kept in GE Office complete as specified and directed.

S&F stainless steel knobs for drapery rod 28mm dia as per sample kept in GE Office complete as specified and directed.

S&F in repair vitreous china wall mountd EWC white with 'P' or 'S' trap front or back inlet any pattern excluding flushing cistern & flush pipe but including plastic water closet seat black closed pattern with flat bottom and cover and hinging device complete all as specified. Make Cera at Part No. S1043114 P Trap with seat cover, colour snow white-14870 or equivalent.

S&F in repair Conceal Cistern with half frame compete set including knob with Twin flushing knob complete all as specified. Make CERA Cat Part No. - B1110112 and knob CERA Cat Part No. B1120104 Q-type Shining Finishing or any Equivalent as Approved By GE.

S&F in repairs vitreous china ware central wash hand basin white in colour350 to 500 mm dia , CP brass waste coupling 32mm etc complete all as specified. Make - CERA cat part No.S2030120, Snow white - 1830 or equivalent as approved by GE.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including CP Spreader , flush pipe and waste pipe complete all as specified and directed. Make- CERA cat part no.- CARVAN S4020105 SNOW white 6605.

S&F in repairs 15 mm bore Pillar tap cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without letter hot or cold with long screwed shank and flynuts screwed for iron pipe. Cat Part No. - ESSCO Medi Series, FLR - S033B OR Equivalent.

Supply and fix single Lever Concealed Deusch Mixer with provision for connection to Over head shower only Make ESSCO Cat Part No. - OPP-15227PM Premium OR any equivalent.

Supply and fix single Lever Concealed Basin Mixer wall Mounted Consisting of operating Lever, wall flange, Nipple, & Spout , Make ESSCO Cat Part No. - ARI - 39233K OR any equivalent.

Taking up or down 15 mm bore steel tubing and connections including cleaning for re-fixing or removal to store complete all as specified.

Taking up or down 20 mm bore steel tubing and connections including cleaning for re-fixing or removal to store complete all as specified.

S&F 15 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all as specified as in short lengths complete all as specified.

S&F 20 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all as specified as in short lengths complete all as specified.

Dismantling PVC water tank of capacity Exc 500 Litre and not Exceeding 1000 Ltr complete all as specified and as directed

S&F Rotational moulded polyethylene water storage tanks of 1000 Lit capacity double layer black in colour (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed

S&F in repair Stop Valve standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm - 90gms) complete all as specified and directed.

S&F in repair bib tap fancy type chromium plated cast copper alloy with capstan head wall flange screwed down screwed for iron pipe 15 mm bore complete all as specified and directed.

S& F Concealed 15 mm bore Angle stop cock (male or female thread) cast copper alloy, chromium plated fancy type with capstan heads, wall flange screwed down screwed for iron pipe and fixed in repairs. Make Jaquar or any equivalent as approved by Engr in Charge.

S&F in repairs CP brass overhead shower 80mm dia round shape with and including CP brass shower arm 240mm long with wall flange complete all specified and directed. Make - ESSCO Cat Part No. - OHS -35497 or as equivalent.

S&F in repair 15 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F 15mm bore CP Toilet Hand Pressed Nozzle (Heath faucet) brass body with 1.0 mtr long tube with CP wall bracket including taking down the old one complete all as specified and as directed. Make - CERA cat part No.F8030301, Snow white - 1830 or equivalent as approved by GE.

M&L PVC (SWR) floor trap plain with grating including jointed with solvent cement of diamemeter 75mm complete all as specified and directed.

S&F in repairs PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints fixed in walls or floor complete as specified and as directed.

S&F in repairs PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed in walls or floor complete as specified and as directed.

S&F PVC (SWR) bends any radius suitable for 110mm bore pipe provided with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius suitable for 75mm bore pipe provided with access door complete all as specified and directed.

S&F PVC (SWR) 110mm Junction (Single T) equal or un equal provided with access door complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110mm setting and jointed with solvent cement complete all as specified and directed.

M&L for Powder coated standard aluminium section as in aluminium doors/windows/partitions etc including glazing clips, fabrication and fixing in position complete to receive sheet glass/particle board complete all as specified and directed.

S&F in repair anodised powder coated aluminium window and ventilator shutters, fixed type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws ,screws handles 2 nos complete all as specified

S&F Powder coated Aluminium door shutters with section weighing 0.55 kg/m including necessary joining cleats,glazing clips,rubber neoprene packing, handles 02nos in each door,hinges,snap beading, screws complete all as specified and directed.

S&F Sheet glass, ordinary quality and glazing with oil putty in square any size in aluminium joinery in each pane ,4 mm thick glass complete all as specified and as directed

M&L solar control film 25 micron reflective type sticked to glass panes as per instuctions of manufacturers complete all as specified and as directed

S&F in repair door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed, aluminium body complete all as specified and as directed

Dismantling wall & ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness, including cover fillets, complete as specified and directed.

S&F for2nd class softwood Boarding 50 mm thick, supplied & fixed with nails in any situation (except flooring and skirting) Clean sawn with butt joints complete all as specified and directed.

S&F Plywood 4 mm thick (No. of Ply-3) grade BWR, type BB, fixed with screws to timber frame for decoration of ceiling work complete all as specified.

M&L applying 1 - 2 mm thick wallcare putty for decoration of ceiling and on wall surfaces complte all as spd and directed.

Supply and fix CP shop disc as per CERA cat part no. F5007016 complete all as specified and directed.

S&F in CP towel rail 60CM long including fitting complete all as specified.

S&F 700mmx500mm, 5 mm thick glass mirror with double coat for protction and longgvity ground edges for safety and silver planting on the back for better reflection.Make Cera cat part no. B3510111.

S&F in repairs sheet glass shelf with towel rod assembly consisiting of 5.5 mm thick sheet glass shelf 12mm wide with CP brass bracket guard railing 60cm long complete all as specified. Make as per Cera cat part no. F5005301

Taking down wooden chowkats or frames with shutter ( without taking off shutter from the frames ), area n. exc. 1.5 Sqm each and removal from site including cutting of holes for removal of hold fasts and making good using new bricks complete all as specified.

All as per item No 89 here in before but area exc. 1.5 Sqm and n. exc. 4.00 Sqm each complete all as specified

S&F Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides ,35mm thick complete all as specified and directed

Supply and fixing factory made shutter, 35 mm thick, 2nd class hardwood rail and style, plain framed, paneled shutter (three panel) with lock rail and panel of 9 mm BWP commercial ply. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified.

S & F 2nd class hard wood (SAL) plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock, strick plate, etc complete as specified, supplied and fixed.Size of frame Size of frame 105 x 60 mm including providing one shop coat of zinc chrome primer .

M&L for painting to new wooden surfaces of any description not otherwise described over 10cm width or girth, and applying two coats of synthetic enamel paint over one coat of pink primer including preparation of surfaces complete all as specified.

S&F factory made soild panel PVC Moulded door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed togehter with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and directed.

M&L for Veneered decorative plywood 6mm thick 5 ply, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work all as specifiec and directed.

M & L for external teak wood lipping 6mm thick and 18/19mm wide for block boards fixed with nails complete as specified and directed.

M & L for 1st class hard wood fillets area exc 3 but n.exc 6 sqcm wrought square or rectangular in section plain or bull nosed, splayed, chamfered or rounded on one edge or face fixed with nails complete as specified and directed.

S&F 150 mm Brass handles, cast type, polished bright, complete all as specified.

S&F 100 mm long stain less steel butt hinges all as specified

S&F Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed

S&F 150mm long Aluminium handle cast type anodised complete all as specified and directed.

S&F 300 mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixedcomplete all as specified.

Taking down carefully old unserviceable copper/aluminium point wiring (light,Exchaust fan, socket or power) complete incl fittings such as switches,ceiling roses, pendents, regulators,bells,sockets,tube light fittings etc, and making good disturbed surface of walls & floors etc complete all as specified and as directed.

Taking down old unserviceable Main Switch, DB's consisting of MCBs wooden/GI/MS sheet board etc for kept in store and for later use all as directed.

M&L for concealed point wiring with two single core PVC insulated, unsheathed, multistranded copper conductor FRLS of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead in and including PVC rigid conduit (medium grade) with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete. NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates.

All as per Item Sl No - 107 here in before but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.5 sqmm green in colour as earth lead for 5/6 A switch-socket point on independent board complete.

All as per Item Sl No - 107 here in before but with 1.5sqmm for two way point wiring all as directed complete.

All as per Item Sl No - 107 here in before but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 4.0 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 4.0 sqmm green in colour as earth lead for 15/16 A switch-socket point on independent board complete.

All as per Item Sl No - 107 here in before but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.5 sqmm green in colour as earth lead for 5/6 A socket point with switch on same board complete.

S&F modular switch one way 6 Amps 230 volts,1 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675501.

S&F modular switch two way 6 Amps 230 volts,1 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675502.

S&F modular bell push switch one way 6 Amps 230 volts,1 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675504.

S&F modular switch one way with indicator 16 Amps 230 volts,1 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675513

S&F modular socket 2 in 1, 2/3 pin ,6 Amp 2 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675550.

S&F modular socket 2 in 1, 3 pin ,6/16 Amp 2 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675555.

S & F modular electronic step regulator (speed regulation in 0-4 steps) 2module suitable for ceiling fan 1200 sweep/1400 mm, 100 Watt complete of make: Legrand mylinc 675530.

S & F modular TV socket 1 module in separate box and providing separate PVC conduit pipe complete of make: Legrand mylinc 675546.

S & F modular RJ 11 telephone socket 1 module in separate box and providing separate PVC conduit pipe complete of make: Legrand mylinc 675541.

S&F modular blanking plate 0.8mm 1 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675590.

S&F modular power unit for 2 ton AC and 3.5KW load of 4 module all as specified and as directed by the Engineer in charge of make: Legrand mylinc 675558

S&F modular white cover plate with frame 1 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675561

S&F modular white cover plate with frame 2 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675562

S&F modular white cover plate with frame 3 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675563

S&F modular white cover plate with frame 4 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675564

S&F modular white cover plate with frame 6 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675566

S&F modular white cover plate with frame 8 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675567

S&F modular white cover plate with frame 12 module inclusive of inner & outer plate complete all as specified and as directed by the Engineer in charge make: Legrand mylinc 675572

S & F modular metal flush box 1/2 module all as directed make: Legrand mylinc 689007

S & F modular metal flush box 3 module all as directed make: Legrand mylinc 689008

S & F modular metal flush box 4 module all as directed make: Legrand mylinc 689009

S & F modular metal flush box 6 module all as directed make: Legrand mylinc 689010

S & F modular metal flush box 8 module all as directed make: Legrand mylinc 689042

S & F modular metal flush box 12 module all as directed make: Legrand mylinc 689011

S & F Bell Ding-Dong AC 230 V Single Pole complete as dircted.

S&F fancy wall light fitting having LED light source of 20W warm light 3000K with lumen of 1000lm Al fixture with white powder coated body incl all necessery connecting arrangements as per site requirements all as specified and directed of make: Philips model no 58153.

S&F bed side light fitting having LED light source of 3W warm light 3000K with lumen of 150lm metallic body incl all necessery connecting arrangements as per site requirements all as specified and directed of make: Philips model no 48042/30/31.

S&F nebula picture light fitting having LED light source of 12W warm light 3000K metallic siliver body incl all necessery connecting arrangements as per site requirements all as specified and directed of make: Philips model no 31441.

S&F recess mounted round downlighter light fitting having LED light source of warm light 3000K PDC housing 1500 lumen incl all necessery connecting arrangements as per site requirements all as specified and directed of make: Philips model no DN296BLED15S-3000PSUWH.

S&F LED strip light with driver of 5 meters length 24W output in warm light 3000K incl all necessery connecting arrangements as per site requirements all as specified and directed of make: Philips model no LED sky cover 5M WW with driver.

S&F surface mounted square shape fitting having LED light source with lumen of 100lm per watt efficiency CRCA housing incl all necessery connecting arrangements as per site requirements all as specified and directed of make: Philips model no SM366CLED326500PSUODWH.

Taking down existing u/s FTL light fitting and S&F in repair decorative box type surface mounted fitting with LED light source 2 feet warm light 4000K with Al extruded batten luminaire for 230 volt AC all as directed by EIC of make Philips BN021LED10S4000PSUGRS1.

Taking down existing u/s FTL light fitting and S&F in repair decorative box type surface mounted fitting with LED light source 4 feet warm light 4000K with Al extruded batten luminaire for 230 volt AC all as directed by EIC of make Philips BN021CLED20SPSUCWGRS2.

S&F ceiling rose ,surface bakelite 65mm x 50mm size with three terminals all specified and as directed.

Taking down ceiling/wall/exhaust fans of any size, sealing cable end, dismantling blades and removing fan and blades to store and refixing same after cleaning all as specified and directed.

S&F in repair ventilation fan with louvers, single phase, 230/240 V, of size 150 mm seeep polycarbonate body, axial flow fan with hidden blades, low noise and weight with thermal overload protection and removable screwless front for easy cleaning incl making holes on wall & making good the distrubed surfaces with all connecting arrangements complete. CRISP AIR PREMIA-AF VENT STN STEE of make usha or equivalent of Havells/Khaitan.

Supply & Fixing DB with sheet metal enclouser 240 volts, 12 way IP-43 and IK-09 with rated 100A Copper bus bar single pole & neutral double door for MCB, incl cutting chases for DB of reqd size and making good distrubed surface area complete all as specified and as directed of make Legrand 507612.

Supply & Fixing DB with sheet metal enclouser 240 volts, 8 way IP-43 and IK-09 with rated 100A Copper bus bar single pole & neutral double door for MCB, incl cutting chases for DB of reqd size and making good distrubed surface area complete all as specified and as directed of make Legrand 507611.

S&F MCB, SP, 10KA, 230V, "C" curve, 06-32 A, ISI Marked complete all as directed of make Legrand 408587 to 95.

S&F MCB, DP, 10KA, 415V, "C" curve, 06-32 A, ISI Marked complete all as directed of make Legrand 408628 to 36.

Material and labour for concealed sub main wiring surface type with two nos single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 6 sqmm and one no single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including surface rigid non-metallic ISI marked PVC conduit medium grade with all fittings and fixings accessories incl taking down old existing complete all as specified and as directed.

Supply only LED garden spike light 5-12W RGB, with dust jet water protection including taking down old u/s and making necessery connections all as specified and directed.

M&L for water proof, 3core PVC insulated and PVC sheathed, copper conductor cable of size 1.5 sqmm, 1100 Volts grade for electrical connection of street light fittings, complete all as specified and directed.

ASSOCIATED TRADING CORPORATION

M S ALOK SAHA

M/S STANDARD CONSTRUCTION CO

SHRI JIBANDHAN PAUL

LIBERAL ENGINEER CONSTRUCTION

SRI SURAJIT SENGUPTA

SHRI JAYANTA GHOSH