Construction of EMI/EMC Building in EMC 2.0 Scheme at SIPCOT Industrial Park, Pillaipakkam

Amount

CIVIL WORKS (Part-A)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc, complete complying with standard specification and as directed by SIPCOT Officers

i) Single pile above 50 tonne and upto 200 tonne safe capacity

a) Initial test ( Test load 2.5 times the safe capacity)

b) Routine test. ( Test load 1.5 times the safe capacity)

ii) Group of two or more piles more than 50 tonne safe capacity

a) Initial test ( Test load 2.5 times the safe capacity)

b) Routine test. ( Test load 1.5 times the safe capacity)

Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for determining safe allowable lateral load on pile etc. complete complying with standard specification and as directed by the SIPCOT Officers.

i) Above 50 tonne and upto 100 tonne capacity pile.

Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, etc. complete complying with standard specification and as directed by the SIPCOT Officers.

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-30 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap) etc, complete complying with standard specification and as directed by the SIPCOT Officers..

600 mm dia piles

Providing and driving in position permenent MS liners for piles from bottom of pile cap as per cl.709.1.4 of IRC 78 - 2014 (up to maximum scour level) including cost of liners and fabricating, welded construction with consumables, labour and plants and driving MS liner 6mm thick to be left permenantly with the pile shaft as per requirement and as per specification and placing them in position with all lead and lift etc. complete complying with standard specification and as directed by the SIPCOT Officers.

Chipping of Pile to the required cut off level and Cleaning away the debris with an average lead of 5 km entirely with city limits etc. complete complying with standard specification and as directed by the SIPCOT Officers.

Removing of clay and Coveyance charges loading and Unloading charges with an average lead of 3 km entirely with city limits etc., complete complying with standard specification and as directed by the SIPCOT Officers.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the SIPCOT Officers.

0-2m depth

Supplying and filling in foundation, basement, etc with filling conveyed Earth layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by SIPCOT officers.

Supplying and filling in foundation and basement with filling Crushed stone dust in layers of not more than 15 cm thick well rammed watered and consolidated complying with standard specification and as directed by SIPCOT officers.

Cement Concrete 1:1-1/2:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the SIPCOT officers

Plain Cement Concrete M 15 1:2:4 (one cement, two sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the SIPCOT officers.

Damp proof course with Cement Mortar 1:4 (One Cement and Four sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc., complete as per standard specificatins and as directed by the SIPCOT officers.

Construction of Solid block wall using best quality of size 40 x 20 x 20 cm conforming to IS 2145 - 1945 made in C.C 1:3:6 using with cement mortar 1.5 (one cement five river sand) including curing and neat finishing etc., complete as per standard specificatins and as directed by the SIPCOT officers.

Providing launching apron using new jeddy stone of size not less than 300 mm thick and weight not less than 40 Kg including the cost of new wedges for filling the gaps, etc complete as directed by the Engineer incharge of works and as per the technical specifications etc., complete as per standard specificatins and as directed by the SIPCOT officers.

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/mᶾ and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 773 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 515.60 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 767 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. etc., complete as per standard specificatins and as directed by the SIPCOT officers. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement

Ground floor

First Floor

Second Floor

Third Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with the standard specificaiton and as directed by SIPCOT Officers. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton and as directed by SIPCOT Officers. (Payment for centering shall be given after the concrete is laid)

Below Plinth beam

For Column, Footing , Column Pedestals , Plinth beams , Grade Beam , Staire case & Pile Cap Side Etc

Square and Rectangular Column

Vertical Surfaces

Above Plinth Surface

Above Plinth for RCC Floor Slab , Roof Slab, Beams , Lintels

Column & Sun Shade

vertical Surfaces

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Brick work in following Cement Mortar using best quality of II Class Ground Moulded Chamber Burnt Brick of size 9" x 43/8" x 23/4"for foundation and basement In Cement Mortar 1:5 including curing, etc., complete complying with standard specifiction.and as directed by SIPCOT officers.

Foundation & basement

Brick work in following Cement Mortar 1:6 using best quality of II Class Ground Moulded Chamber Burnt Brick of size 9" x 43/8" x 23/4"for foundation and basement In Cement Mortar 1:6 including curing, etc., complete complying with standard specifiction.and as directed by SIPCOT officers.

Ground Floor

First Floor

Second Floor

Third Floor

Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Brick of size 9" x 43/8" x 23/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by SIPCOT officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground Floor

First Floor

Plastering the surface of walls with Cement Mortar 1:5 (One cement and Three sand), 12mm thick in all floors including curing etc., complete as per standard specification and as directed by SIPCOT officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors etc., complete as per standard specification and as directed by SIPCOT officers.

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.as directed by SIPCOT officers.

Painting two coats of newly plastered wall surface with ready mixed plastic exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete as per standard specification and as directed by SIPCOT officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water etc., complete as per standard specification and as directed by SIPCOT officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification and as directed by SIPCOT officers.

Providing and Laying of ESD Vinyl Tile Floor Toppings by Application of 15 mm width x 50micron thick copper tape as 600 mm x 900 mm Grid,,Application of Conductive adhesive,Application ESD Safe Tiles of Thickness – 2mm -Resistance: >10E9 with size 600 X 600 mm in Colour –Dark Grey chips on White Base hot air fused with nearest colour matching PVC Welding Rod etc., complete as per standard specification and as directed by SIPCOT officers.

Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification and as directed by SIPCOT officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with Anti skid Self Designed Colour Ceramic Tiles of size 305 x 305 x 6mmceramic tiles laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. and as directed by SIPCOT officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, ceramic tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by SIPCOT officers.

Paving the floor with best approved quality fine polish Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockableaction, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work etc., complete complying with standard specification and as directed by SIPCOT officers.

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work etc. complete complying with standard specification and as directed by SIPCOT Officers.

Supplying and fixing mild steel iron grill for Windows Ventilators and grill gate etc., including one coat of red oxide primer using M.S. angle of size 40x40x6mm and grill using 20x6mm MS flat and necessary hold fast with M.S. angle of size of 40x40x6mm - 230mm long spliced at end is to be provided appropriate places for fixing the grill etc complete complying with standard specification. The type design for the grills should be got approved by the SIPCOT officers before execution. etc. complete complying with standard specification and as directed by SIPCOT Officers

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc. complete complying with standard specification and as directed by SIPCOT Officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

ABS DOOR / EQUIVALENT Specification: Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work etc. complete complying with standard specification and as directed by SIPCOT Officers

Design Pre-laminated Door

Plain Pre-laminated Door

FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers etc., complying with standard specification and as directed by SIPCOT officers.

Solid PVC Door Shutters with frame using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter etc., complying with standard specification and as directed by SIPCOT officers.

Supply and fixing of 120 Minutes Metal Fire Rated Doors Door size 1200 mm x 2100 mm fix panel above 2400 mm Double leaf 46mm thick steel door shutter of 120 Minutes Fire Rated confirming to B5-475 Part 20-22 & 15:3614 Part-II, Prototype certified from GQMC/NABL Approved Lab. Fabricated with 2 nos of 1.2 mm thick galvanized steel sheet sandwiching fire insulation materials (Rockwool) in between suitable for 120 minutes. Door frame 1.6 mm thick galvanized sheet of 100*57 mm & fixing with dash fastener (Payable separately) of approved size.The frame & shutter are finished with powder coated approved shade. 1. Hinges of Size 100 x 75 x 3mm 2.Door Closer with Std Arm. 3, Panic Bar (Single Point) For Single Leaf Door 4. Panic Trim 5.EPDM Seal 6.6 mm thick Fire Rated Clear Glass of Size 200 x 300 mm For VP saint gobain 7. Klimas Make Anchor Fastener of size 10x30mm along with Metal Hole Cap & PVC Shims etc., complying with standard specification and as directed by SIPCOT officers.

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., complying with standard specification and as directed by SIPCOT officers. - Manually Operated

Providing And Fixing Of Polyurethane Foam As Internal Partition Wall Thermal Insulation Panels Or Sandwich Insulated Panels Wihboth Internal And External 0.50Mm Total Coated Thickness Repainted Galvanized Iron Sheet With Micro Ribbed Profile And The Insulation Material Will Be Chlorofluoro Carbon And Hydro Chlorofluoro Carbon Free , High Performance Rigid Polyurethane Foam (Puf) Conforming To Is 12436 Having Density Not Less Than 40±2Kg/M3, Thermal Conductivity (K-Value) 0.024 W/M.K Measured At 10 Degree C Mean Temperature Along With Necessary Flashings Such As L Flashing, Flashing Etc& Accessories Such As Screws ,Fastners ,Sealants Etc For Fixing The Paneletc., complying with standard specification and as directed by SIPCOT officers.

50mm thick PUF Internal partition wall panel

Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre ‘T’. The ‘T’ shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of ‘T’ section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of ‘T’ section are made at required intervals not exceeding 1200mm. The main runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile ‘L’ Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look etc., complete complying with standard specification and as directed by the SIPCOT officers.

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the SIPCOT officers

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete complying with standard specification and as directed by the SIPCOT officers

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc., complete complying with standard specification and as directed by the SIPCOT officers

Design, supply, Delivery, installation and commissioning of Passenger Lift (Brand: Johnson / Kone / OTIS) of capacity 13 persons as per the following specifications. 1. Type of Lift : Passenger MRL , 2. Load / Speed: 13 persons / 1.00m per second. , 3. Drive: Micro Processor based VVVF , 4. Travel / Pit / Head room: 14.4m / Pit 1400mm / Head room 4000mm, 5. Number of Floors: 11 (Stilt + 10 upper floors) 6. Floor Display Chart: S,1,2,3,4,5,6,7,8,9,10. Number of Landing Entrances: (Stilt + 10 upper floors) , 7. Number and entrances: 1 (One), In Front only , 8. Position of Machinery: Directly above the lift well Gearless 9. Size of Lift Well: 2430 x 2430mm Position of car ,10. Lin car inside size 2000 x 1100 x 2200mm , 11. Clear opening of Gates / Doors / Lintel 800x 2000mm, Lintel - 2200mm, 12. Type of Design of Lirf car: Stainless steel 1.5mm - Hairline finish , 13. Car ceiling/ Car flooring Integrated ceiling with RL 20F - Granite flooring 20mm recess etc., complying with standard specification and as directed by SIPCOT officers.

13 Persons

Landscaping

Turffing including Biotic Soil media maintaining with watering for One year

PLUMBING WORKS (PART-B)

SANITARY INSTALLATIONS

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complying with standard specification and as directed by SIPCOT officers. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting W.C. pan with ISI marked white solid plastic seat and lid

Supply, installing, testing and commissioning of CP brass health faucet cum ablution tap assembly of approved make comprising of 2 way bib cock of approved make with heavy casted CP brass wall flange, angular stop cock and one CP brass health faucet of approved make with 1m long PVC tube of 8mm dia etc., complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing of White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mm etc., complying with standard specification and as directed by SIPCOT officers.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste, 32 mm CP. Bottle trap and unions of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require etc., complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing of Ornamental Type White Glazed Porcelain Corner ‘L’ Type Wash Hand Basin of size 350mm etc., complying with standard specification and as directed by SIPCOT officers.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 etc., complying with standard specification and as directed by SIPCOT officers.

15 mm nominal

Providing and fixing white vitreous wash down water closet (MATRIX Set-1) of Hindware Cat. No. 70002 including wash basin (600 x 350mm) with one pair mounting brackets, C P pillar tap Jaquar Cat. No. 15001, EWC & cistern complete with fittings and seat cover, one no. hinged rail 760mm and five nos. of grab rail 600mm etc., complying with standard specification and as directed by SIPCOT officers.

Supply and fixing Chromium Plated Stop Cock 15mm dia

Supply and fixing Brass Chromium Plated Soap Tray of size 150mm x 100mm etc., complying with standard specification and as directed by SIPCOT officers.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms etc., complying with standard specification and as directed by SIPCOT officers.

Providing and fixing toilet paper holder : C.P. brass etc., complying with standard specification and as directed by SIPCOT officers.

Supply and fixing Brass Chromium Plated Towel Rail 60cm long and 20mm dia with Brackets etc., complying with standard specification and as directed by SIPCOT officers.

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works etc., complying with standard specification and as directed by SIPCOT officers.

INTERNAL DRAINAGE

Providing, fixing PVC soil waste pipe 6 kg/cm2 with ISI monogram including all fittings such as W.C. connector, bends, junctions, inspection doors, offsets, vent cowls, as required/directed at site, jointing with rubber ring and rubber lubricant including cutting holes in walls and making good the same etc, complete complying with standard specification and as directed by SIPCOT Officers.

110 mm dia

75mm Dia

Providing at site, lowering & laying in trenches, aligning & jointing of PVC pipes of class III (6 kg/ cm2) as per IS:4985 and as per specification with rubber ring with socket and spigot joint,(EPDM/SBR) for all depths including well graded granular bedding (Type-E) for pipe length as per drawing and specification including hydraulic field testing and commissioning etc, complete complying with standard specification and as directed by SIPCOT Officers.

40mm diameter pipe

Supplying and fixing position CI Nahani Trap / Floor Trap of size 100/75 mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification and as directed by SIPCOT Officials - Nahani Trap of size 100 x 75mm with stainless steel gratings

Providing and fixing S.S. round grating with round frame, 127 mm Dia overall size, glossy finish Chilly Cat. No. CRG-R-127 or approved equivalent) including setting in floor with cement mortar 1:3 etc., complete complying with standard specification and as directed by SIPCOT Officials

Providing, fixing, of 110mm x 63mm PVC Reducing Elbow for floor drain point and coupler cutting chases, the floor / slab, repairs complete as required and connection to pvc waste pipe etc., complete complying with standard specification and as directed by SIPCOT Officials

Providing and fixing clean out plug with suitable insert keys for opening in: brass / SS cap, male threaded joint with threaded uPVC socket fixed to uPVC pipe joints as required complete in all respects for 110mm dia Pipe. (Floor Clean out / FCO) Cilly Cat No. CO-S-128 or approved equivalent etc., complete complying with standard specification and as directed by SIPCOT Officials.

Providing and fixing PVC threaded end cap joint to PVC pipe as required complete in all respects for 110mm dia pipe. (Clean out plug / COP) etc., complete complying with standard specification and as directed by SIPCOT Officials

WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR-11) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints Concealed work, including cutting chases and making good the walls etc., complete complying with standard specification and as directed by SIPCOT Officials.

15mm nominal outer dia. Pipes

20mm nominal outer dia. Pipes

25mm nominal outer dia. Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC pipe SDR-11 upto 50mm dia having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints etc., complete complying with standard specification and as directed by SIPCOT Officials.

Internal work - Exposed on wall

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

Providing and fixing brass stop cock of approved quality etc., complete complying with standard specification and as directed by SIPCOT Officials.

Chromium Plated Stop Cock 15mm dia

20mm nominal bore

Providing and fixing gun metal gate valve (Heavy Duty) etc., complete complying with standard specification and as directed by SIPCOT Officials.

25mm nominal bore

32mm nominal bore

RAIN WATER PIPES AND FITTING

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion etc., complete complying with standard specification and as directed by SIPCOT Officials.

Single socketed pipes

160 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion etc., complete complying with standard specification and as directed by SIPCOT Officials.

Shoe (Plain)

160 mm Shoe

110 mm Shoe

ELECTRICAL SUPPLY & ARRANGEMENT (PART C)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & office, etc.) etc., complete complying with standard specification and as directed by SIPCOT Officials.

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge PVC conduit pipe concealed in wall and ceiling with MS accessories with MS switch box with 5A FT switch (two way) in flush with wall and covered with 3mm thick hylem sheet for MS switch box with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed staircase light point etc., complete complying with standard specification and as directed by SIPCOT Officials.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point etc., complete complying with standard specification and as directed by SIPCOT Officials.

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed power plug point etc., complete complying with standard specification and as directed by SIPCOT Officials.

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour etc., complete complying with standard specification and as directed by SIPCOT Officials.

Supply and run of 2 of 2.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour etc., complete complying with standard specification and as directed by SIPCOT Officials.

Supply and fixing of following MODULAR SWITCHES & SOCKETS as per ISI with standard specification and etc.Compete comply as per directed by SIPCOT Officers

6A Switch 1W - 1 Module

6A Switch 2W - 1 Module

16A Switch 1W - 1 Module

Stepped Electronic 300W / 450W Square Type FanRegulator

6/16A Socket - 2 Module

6A 5 pin Universal Socket - 2 Module

FLUSH MOUNTING BOXES (GI)

Flush Box - 1/2 Module

Flush Box - 3 Module

Flush Box - 4 Module

Flush Box - 6 Module

Flush Box - 8 Module

COMBINED PLATES (PLASTIC)

1 Module Cover Plate

2 Module Cover Plate

3 Module Cover Plate

4 Module Cover Plate

6 Module Cover Plate

8 Module Cover Plate

Supply and fixing of 25A flush type wall socket with 25A DP MCB for AC Plug etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing of single box type LED Fitting complete with electronic ballast with TW round blocks on wall or ceiling with Flu. Tube with PVC Unsheathed copper leads from terminals to the fitting etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing of 24W LED 4000K 2x2 Square type Recessed Fitting with LED etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing of 1200 mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300 mm down rod and Fan clamp etc., complete and as directed by SIPCOT Officers

Supply and Fixing of 300 mm (12") sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall etc., complete and as directed by SIPCOT Officers.

Supply and fixing of 7 SEGMENTS (3 TIER) 3 PHASE DISTRIBUTION BOARD WITH MCB 6 way TPMCB sheet steeldistribution boards flush type / surface type fitted withbus bars and neutral links with single / three phase MCB outgoings and separate 6 way provision for accommodating One No. 4 pile incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 6 ways in each segment) and separate provisions for MCB / Isolator (totally 18 Nos.) for sub incomers in 3 segments with label holder and provisions for taking up cable for size not less than 35 sq.mm. etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply and fixing of 7 SEGMENTS (3 TIER) 3 PHASE DISTRIBUTION BOARD WITH MCB 4 way TPMCB sheet steel distribution boards flush type / surface type fitted with bus bars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pile incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 4 ways in each segment) and separate provisions for MCB / Isolator (totally 12 Nos.) for sub incomers in 3 segments with label holder and provisions for taking up cable for size not less than 35 sq.mm. etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing of MINIATURE CIRCUIT BREAKERS 240 V / 415V 50HZ - AC SUPPLY SUITABLE FOR BOTH LIGHTING AND MOTORCIRCUITS.

Single Pole 6A to 32A, 10KA

Triple Pole & Neutral 63A, 10KA

40 Amps 30 MA DP

Supply and Fixing of Vertical TPN Distribution Boards (with MCCB Incomer); Double Door; IP43, as per IS 8623 III; Impact resistance IK09; Frame MCCB Incomer & Single Phase/Three Phase MCBs as Outgoing (for power loads exceeding 100A) 8 Way, MCCB + 24 Modules

Triple Pole 32A, 10KA

Supply and Fixing of SINGLE PHASE DISTRIBUTION BOARD WITH MCBs 8 way vertical SPMCB sheet steel distribution boards flush type / surface type fitted with bus bars and neutral links with single phase MCB outgoings and separate 2 way provision for accommodating One No. 2 pole incoming MCB / Isolator and another separate 2 way provision for accommodating One No. 2 pole ELCB / RCD with label holder and provisions for taking up cable for size not less than 35 sq.mm etc, complete complying with standard specification and as directed by SIPCOT Officers.

125A TP MCCB

Earthing

Supply and fixing Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth etc, complete complying with standard specification and as directed by SIPCOT Officers.

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work sq.mm etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5 metre etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, Erection of 8m Free Standing Single Arm Bracket 8 sided Octogonally continously tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with following specification.Bottom Pole Dia - 130mm Top Pole Dia - 70 mm Thickness of Pole - 3 mm The pole should be hot dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron etc., including foundation with necessary bolt & Nuts etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing of 120W LED Street Light Fitting with LED etc, complete complying with standard specification and as directed by SIPCOT Officers.

CABLE

Supply and laying of 3-1/2 x120 sq.mm.PVC AR. LTUG cable in HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and laying of 3-1/2 x70 sq.mm.PVC AR. LTUG cable in HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and laying of 3-1/2 x50 sq.mm.PVC AR. LTUG cable in HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply and laying of 3-1/2 x25 sq.mm.PVC AR. LTUG cable in HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good etc, complete complying with standard specification and as directed by SIPCOT Officers.

CABLE GLAND & TERMINATION

Supply and providing cable end termination of 3-1/2 x 120sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and providing cable end termination of 3-1/2 x 70sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc, complete complying with standard specification and as directed by SIPCOT Officers.

SUPPLY AND FIXING OF FOLLOWING OF CABLE TRAY AS PER STANDARED SPECFICATION AND AS DIRECTED BY SIPCOT OFFICERS.

GI Hot Dip / Powder Coated 16 SWG Cable Tray with 150mm width and 50mm height tc, complete complying with standard specification and as directed by SIPCOT Officers.

GI Hot Dip / Powder Coated 16 SWG Cable Tray with 300mm width and 50mm height tc, complete complying with standard specification and as directed by SIPCOT Officers.

GI Hot Dip / Powder Coated 16 SWG Cable Tray with 450mm width and 50mm height tc, complete complying with standard specification and as directed by SIPCOT Officers.

Fabrication of MS Angle Support tc, complete complying with standard specification and as directed by SIPCOT Officers.

11 KV OUTDOOR RING MAIN GEAR (RMG)

Supply and erection of 11 KV, 25 KA, 630 A, HT Outdoor Three Panel Ring Main Gear etc, complete complying with standard specification and as directed by SIPCOT Officers.

11 KV OUTDOOR VACCUM CIRCUIT BREAKER

Supply and erection of 11 KV, 25 KA, 630 A, HT Outdoor Single Panel Vaccum Circuit Breaker etc, complete complying with standard specification and as directed by SIPCOT Officers.

HT CABLES

300 sq.mm. 3 core HT XLPE 11KV (E) SISMV11E3 x 3002797

CABLES, ACCESSORIES AND KITS

300 sq.mm. 3 core HT Cable Indoor Terminations XLPE 11KV (E) - EPKT 3121

3 PHASE UPS (Three Phase In & Single Phase Out)-10 KVA

4 PHASE UPS (Three Phase In & Single Phase Out)-30 KVA

5 PHASE UPS (Three Phase In & Single Phase Out)-40 KVA

6 PHASE UPS (Three Phase In & Single Phase Out)-60 KVA

MAIN MV PANEL

CABLE ENTRY: BOTTOM/TOP

Supplying, Erecting, connecting & commissioning, main MV panel board of a made up of sheet steel, dust and vermin proof of Cubicle type, Indoor type, floor mounting, free standing, Compartmentalized design and fabricated with 14 CRCA sheet steel for main frames, and 16 CRCA sheet steel Doors & partitions and removable of Gland plates. etc, complete complying with standard specification and as directed by SIPCOT Officers. The Panel Board shall be incorporated with the following:-

Incomer 1: 1000 Amps 4P EDO ACB of 50kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

There shall be one set of Metering Compartment incorporated with the following:-

i) CTs of ratio 2000/5Amps of Class 1.0 and burden 15VA with CT short link terminal block for metering - 3 Nos.

iii) CTs of ratio 1000/5Amps of Class 1.0 and burden 15VA with CT short link terminal block for APFC - 1 No.

iv) CTs of ratio 1000/5Amps of Class 5P10 and burden 15VA with CT short link terminal block for Earth Fault Relay - 3 Nos.

v) 1 set of (2 OC+1 EF) Earth fault relay

vi) 1 Set of RYB & On, Off, Trip Indication lamp of LED cluster Type with Control breaker shall also be provided.

Incomer 2: 1000 Amps 4P EDO ACB of 50kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

There shall be one set of Metering Compartment incorporated with the following:-

i) CTs of ratio 1000/5Amps of Class 1.0 and burden 15VA with CT short link terminal block for metering - 6 Nos.

iii) 1 Set of RYB & On, Off, Trip Indication lamp of LED cluster Type with Control breaker shall also be provided.

Bus coupler -1 : 1000 Amps 4P EDO ACB of 50kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

BUS BAR

1000A 4P, BUS BAR , 415V

Outgoings :Part - A 800 Amps TPN MCCB of 35kA(Ics) withstanding capacity with Adjustable Overload, Fixed Short Circuit Relays - 2 Set

200 Amps TPN MCCB of 35kA(Ics) withstanding capacity with Adjustable Overload, Fixed Short Circuit Relays - 3 Set

Incomer 3: 1000 Amps 4P EDO ACB of 50kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

There shall be one set of Metering Compartment incorporated with the following:-

i) CTs of ratio 1000/5Amps of Class 1.0 and burden 15VA with CT short link terminal block for metering -3 Nos.

iii) 1 Set of RYB & On, Off, Trip Indication lamp of LED cluster Type with Control breaker shall also be provided.

Incomer 4: 1000 Amps 4P EDO ACB of 50kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

There shall be one set of Metering Compartment incorporated with the following:-

i) CTs of ratio 1000/5Amps of Class 1.0 and burden 15VA with CT short link terminal block for metering -3 Nos.

iii) 1 Set of RYB & On, Off, Trip Indication lamp of LED cluster Type with Control breaker shall also be provided.

Bus coupler -2 : 1000 Amps 4P EDO ACB of 50kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

BUS BAR

1000A 4P, BUS BAR , 415V

Outgoings :Part - A 800 Amps TPN MCCB of 35kA(Ics) withstanding capacity with Adjustable Overload, Fixed Short Circuit Relays - 2 Set

200 Amps TPN MCCB of 35kA(Ics) withstanding capacity with FOD, Adjustable Overload, Fixed Short Circuit Relays - 1 Set

Incomer 5: 200 Amps 4P EDO ACB of 35kA(Ics) withstanding capacity with Adjustable Overload, Short Circuit Relays -1 Set

BUS BAR

300A 4P, BUS BAR , 415V

100 Amps TPN MCCB of 35kA(Ics) withstanding capacity with FOD, Adjustable Overload, Fixed Short Circuit Relays - 3 Set

01. The withstanding capacity shall be Ics only.

02. Electrical Interlocking arrangement and Auto operation should be provided between Incomer- 1 &2 (EB), Incomer-3&4 (DG) , Incomer-5 (Solar) & Bus coupler(BC)-1&2.

Busbar : Aluminium

Rating : 1200 Amps TPN 50Hz

Provision made for Main Busbar Extension to be given both end of the MAIN MV PANEL for future extension.

AUTOMATIC POWER FACTOR CORRECTION RELAY PANEL (APFCR PANEL)

Supplying,erecting,connecting & commissioning of 150 KVAR APFCR Panel in MS CRCA sheet with free standing floor mounting enclosure with all necessary interconnections of capacitor Bank for 8-steps APFC relay shall be incorporated the following capacitors to maintain the power factor etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supplying, Erecting, connecting & commissioning of a made up of sheet steel, dust and vermin proof of Cubicle type, Indoor type, floor mounting, free standing, Compartmentalized design and fabricated with 14 CRCA sheet steel for main frames, and 16 CRCA sheet steel Doors & partitions and removable of Gland plates. etc, complete complying with standard specification and as directed by SIPCOT Officers. The Panel Board shall be incorporated with the following:-

Incomer

200 Amps TPN MCCB of 25kA(Ics) withstanding capacity with FOD, Adjustable Overload, Fixed Short Circuit Relays - 1 Set

Outgoing

40 Amps TPN MCB of 10kA(Ics) withstanding capacity - 8Nos

32 Amps TPN MCCB of 10kA(Ics) withstanding capacity- 3Nos

Supply and fixing Earthing arrangements with CU. Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by theSIPCOT Officers.

Supply and fixing of followings SAFETY ACCESSORIES etc, completed as per directed by SIPCOT

AC Chargeable Emergency Lamp 2 x 11W PL Lamp with all connected accessories

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS - 5Nos

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle

Hand Gloves 11KV Grade

Danger Board as required by the Electrical Authorities

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Earth Discharge Rod

CCTV (PART-D)

Supply, installation, testing & commissioning of Bullet Camera 2 MP @ 30 fps for real-time viewing and recording, Motorised Varifocal from 2.7~13.5 mm P-IRISL lens supporting corridor mode in the lobby area. inbuilt Mic for voice recording inbuilt IR for nighttime viewing up to 50 meters and inbuilt SD Card up to 128GB. inbuilt Analytics like - Intrusion, Line Crossing, , Missing object detection, Face detection,, Perimeter Intrusion Detection, Line Crossing Detection, Missing Object Detection, Crowd Detection, Five-window video motion detection, People detection, Vehicle detection, Time filter ,Object Detection: people, vehicle (4-wheeled); Path Extraction, Video Streams: Triple-Stream. certified - IK-10, IP66/IP67, UL (UL 62368-1) CE, FCC, BIS, ONVIF S, G .T with minimum 3 year warranty,NDAA Complied ,non Hisilicon SOC.Built in cybersecurity in camera. etc, complete complying with standard specification and as directed by SIPCOT Officers. (Brand: Dahua or equivalent)

Supply, installation, testing & commissioning of Bullet Camera 2 MP @ 30 fps for real-time viewing and recording, Motorised Varifocal from 2.7~13.5 mm P-IRISL lens supporting corridor mode in the lobby area. inbuilt Mic for voice recording inbuilt IR for nighttime viewing up to 50 meters and inbuilt SD Card up to 128GB. inbuilt Analytics like - Intrusion, Line Crossing, , Missing object detection, Face detection,, Perimeter Intrusion Detection, Line Crossing Detection, Missing Object Detection, Crowd Detection, Five-window video motion detection, People detection, Vehicle detection, Time filter ,Object Detection: people, vehicle (4-wheeled); Path Extraction, Video Streams: Triple-Stream. certified - IP42, UL (UL 62368-1) CE, FCC, BIS, ONVIF S, G .T with minimum 3 year warranty,NDAA Complied ,non Hisilicon SOC.Built in cybersecurity in camera. etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of Dome Camera 2 MP @ 30 fps for real-time viewing and recording, Motorised Varifocal from 2.7~13.5 mm P-IRISL lens supporting corridor mode in the lobby area. inbuilt Mic for voice recording inbuilt IR for nighttime viewing up to 50 meters and inbuilt SD Card up to 128GB. inbuilt Analytics like - Intrusion, Line Crossing, , Missing object detection, Face detection,, Perimeter Intrusion Detection, Line Crossing Detection, Missing Object Detection,, Crowd Detection, Five-window video motion detection, People detection, Vehicle detection, Time filter ,Object Detection: people, vehicle (4-wheeled); Path Extraction, Video Streams: Triple-Stream. certified - IK-10, IP66/IP67, UL (UL 62368-1) CE, FCC, BIS, ONVIF S, G .T with minimum 3 year warranty,NDAA Complied ,non Hisilicon SOC.Built in cybersecurity in camera etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of 16 Channel NVR (Network Video Recorder), for recording up to 32 CH @ 1080P with 04 nos. SATA HDDs minimum 40TB storage or more (recording requirement all cameras recording at 2MP, 25fps for 30 days), H.265/H.264/MJPEG/MPEG4 codec decoding, Front Control Panel with LEDs Indication, 3 nos. USB, iPhone; iPad; Android based Mobile clients, Video Export feature on USB, Search Mode,Deep Search : Time/Date; Alarm; Motion Detection (MD); Exact Search (accurate to a second); Smart Search, HDMI Output, Alarm Input (4 nos.), Alarm Output (1 nos.), Incoming - 190 Mbps, Total Bandwidth incoming/outgoing - 224 Mbps, Operating Temperature –10°C to 55°CCertification: UL, CE, FCC & BIS including fixing accessories and cable termination with required connectors/Jack, etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply, installation, testing & commissioning of 16 TB HDD etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply, installation, testing & commissioning of 43 inch or higher Full HD LED TV, 43 inch or higher Full HD LED TV, Screen Type: LED Backlit LCD, Screen Size (Inches): 43, Resolution (Pixels) 3840 x 2160 (UHD), Category Smart display, Typical Brightness: 500 or better, Inbuilt Speakers 10W x 2, Warranty (Years) 3 Operation Hours 24 x 7 ,Static contrast Ratio 4000:1 or better, Haze % ( for lesser reflection of room light) 25% or more, Screen Mirroring Yes, Mount Type: Wall Mount, Power Consumption Typical (Watts) 110 or lower, Security features by USB lock, Panel button lock, security lock Yes, Ports & Connectivity, Number of HDMI Ports: 3, Number of USB Ports: 2,Number of Ethernet Ports 1 Display Port: Yes, Operating system from same display oem: Yes, Inbuilt Memory 16 GB, Inbuilt Embedded Signage Software: Yes Laptop/ Pc can be accessed thru display: Yes, Accessories: Remote Control, Batteries, User Manual, Power Cable ,Certification : BIS Registration as per CRS of Meity Yes, Safety & EMC Certificate CE,FCC,UL, IP5X, EMC Class B, Panel depth 30 mm or less, Operating Temperature (Degree C) : 0-40'C, Operating Humidity (%RH) : 10—80,Product Life ( Hrs.) : 50000 hrs. MTBF, Digital signage Software "The Licensed Content Management /distribution software should be Support. etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of 12U Rack Frame,800X1000,Steel,NRS,CKD,Casters Type 3,Black,Levellers,19" Adopter kit,,Loops,Black,Perforated Door,800,Convex,NRS,Black, Perforated ,Dual,NRS,Black,Side Panels,1000,Vented,NRS,Black,Swing Handle, Mechanical Lock, Single Point, Common Key, Die Cast Metal, Swing Handle, Mechanical Lock, Three Point, Common Key, Die Cast Metal, Server ,IT Rack mount power distribution unit, 1Ph, 230V, 32A, 50,60Hz, Zero U standard with 12 X Indian Round Pin 5,15A, 16A MCB X 2 Circuits- PDU Rating 7.3KVABottom feed-3Mt, Black, Horz. Cable Organiser,1U,Channel On Front, Shelf,1000,Black,Mounting Hardware-CR (Pack of 20),ITE, Server Rack Air Circulation module, Tower Mount,360CFM etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of 24-Ports 10/100/1000Mbps PoE + 4-Ports Combo GE/SFP Smart Managed Switch, Switch should support maximum PoE Budget of 240watt. The switch should have minimum switching capacity of 40Gbps. Switch Should support 16K MAC addresses and 4000 VLAN. Switch should support Jumbo frame, ITU-T G.8032, IEEE 802.1ad, IEEE 802.1Q, IEEE 802.1v, IEEE 802.3ac, IEEE 802.1AX, OSPF, BGP, DHCP Server and Relay for IPv4 and IPv6, DHCP Option 82. Switch should support IGMP v1/v2/v3 snooping, MLD v1/v2 snooping with min 512 multicast groups. Switch should support ACL, BPDU protection, Dynamic ARP Inspection, DHCP Snooping, STP root guard, IP Source Filtering, RADIUS and TACACS+. Should support UDLD, Digital Diagnostic monitoring, Port and VLAN mirroring and IEEE 802.1ag or equivalent. Should support SNMPv6, Telnetv6 and SSHv6, NTPv6, Open flow and have USB or equivalent interface for easy backup and restore. Switch should support MAC Sec/FIPS 180-1 and IEEE 1588v2 PTP. Operating Temperature of switch should be -40°C to 75°C. The switch should have internal/external (DIN rail mountable) AC power supply. Protection Class should be minimum IP 30 and NEMA TS-2. Switch should be EN55022, EN55024, IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-8, IEC60068-2-31, IEC60068-2-27, IEC60068-2-6. Should support UDLD or equivalent feature to prevent loops on detecting unidirectional links, Connectivity Fault Management, Monitoring Temperature, Supply voltage, Average transmit power, Average receive power and Laser bias current of the FO module, should have feature if any intrusion is detected on fiber link the particular port should be shutdown automatically. All the switches should be offered with min 5 years replacement warranty with proper back-up on respective-OEM letter Head. All the switches and FO Modules should be from the same OEM etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply, installation, testing & commissioning of Cable Cat 6 UTP 23AWG FR-PVC Blue etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of 24VDC Power supply etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of 20 mm dia heavy duty (2mm thick) PVC conduit with 1 number 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor as earth continuity wire etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of Cat 6 UTP Modular RJ-45 Connectors etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of CAT6 UTP 24AWG PATCH CORD:1M/2M,Plug 30U Snagless etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of1KVA UPS etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of Bracket for Bullet Camera,600 mm long cross arm of 50 mm x 50 mm x 6 mm mild steel angle iron with necessary clamps, bolts, nuts etc. on poles complete in all respects including painting with aluminium paint etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing & commissioning of Face Plate - Single (Keystone Jack,square) etc, complete complying with standard specification and as directed by SIPCOT Officers.

FIRE FIGHTING (PART E)

FIRE DETECTION AND ALARM SYSTEM

Supply, installation, testing and commissioning of Micro Processor based conventional 4 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing and commissioning of conventional Smoke detector suitably mounted on ceiling with junction box /false ceiling l using fixing accessories like screws, plug, clamps and etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing and commissioning of response Indicator (RI) providing on wall using fixing accessories like screws, plug, clamps and etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Electronic Hooter/ Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply and laying of FRLS PVC insulated 2 C X 1.5 Sq mm AR. Cu. Cable on ceiling / wall using , etc. fixing accessories like screws, plugs, clamps etc, complete complying with standard specification and as directed by SIPCOT Officers.

FIRE FIGHTING SYSTEM

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: JINDAL / EQUIVALENT.

150 mm dia.

80 mm dia.

25 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessaryetc, complete complying with standard specification and as directed by SIPCOT Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Servicing the SS Hydrant Valves by disconnecting from pipe line, dismantling, checking the operation of rotating spindle, replacing rubber ‘O’ ring of valve seating, repalcing rubber gasket of 80mm dia OD x 65mm dia ID, repalcing the 5/8” x 21/2 bolt, nut, washers, re-connecting with hydrant system as per standard methods etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply and delivery of DI D/F Butterfly Valves with GGG 40 or GGG 50 as per IS3896 (Part 2) 1985 and subsequent revisions Double eccentrically disc with renewable soft seal on the disc and body seat face of Stainless Steel / nickel weld overlay micro finished with powder or liquid Epoxy coating with minimum thickness of 250 microns applied on both body and disc inside and outside Face to Face dimensions as per AWWA C 504 or BS 5155 or IS 13095 and with 5 years warranty etc, complete complying with standard specification and as directed by SIPCOT Officers

400 mm dia PN16

450 mm dia PN16

Manufacture supply and delivery of DI D/F Diaphragm type own medium controlled Pressure Reducing and flow limit control valve with cast body of ductile iron grade GGG-40 or GGG- 50 or as per IS 3896-Part-2-1985 customized control cylinder for linear control behaviour or equivalent, performed diaphragm and pull out safe profile sealing ring of EPDM, threaded inserts (CORFIX - to prevent the coating from coming off in the connections area as well as corrosion and incrustations in the control circuit) or equivalent. 2 pressure gauges for operator-friendly control to determine the actual inlet and outlet pressure connected directly to the valve. Flange connection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538, all parts (Epoxy coating, and diaphragm) in contact with medium are as per KTW and DVGW certified (harmless)/ WRAS & NSF approved. The EPDM rubber & Epoxy coating (EP-P) should be approved by W270. (EP-P)/ WRAS & NSF.” of 50 mm etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers

150 mm dia

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: KIARTAR / OMEX / EQUIVALENT.

Supply and Fixing of C.I. DOUBLE AIR VALVE AS PER ISI 14845/2000 AND WITH 5 YEARS WARRANTY --200mmdia etc, complete complying with standard specification and as directed by SIPCOT Officers.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supplying & Fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 300mm width and 50mm height etc, complete complying with standard specification and as directed by SIPCOT Officers

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge,operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

PUMPING

FIRE PUMPS AND HYDRANT WORKS

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top harge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filteretc. (Make: Kirloskar / Equivalent). d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition. e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required. g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement. All works carried out as per standard methods and as instructed by the manufacturer etc, complete complying with standard specification and as directed by SIPCOT Officers. (Make: Kirloskar / Equivalent)

Supplying, erection, testing and commissioning of Diesel Engine Pump Main Control Panel & Jockey Pump including necessary auto cut-in, cut-off and manual operations, battery charger switch arrangements, voltmeter, ammeter and running indication siren provision, wall mounting type, etc, complete complying with standard specification and as directed by SIPCOT Officers

PRESSURE SWITCH

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

BUTTERFLY VALVES WITH TOP AND BOTTOM OF S.S. 410 SHAFT, WAFER LINER/ WITH REDUCTION GEAR UNIT (CONFORMING TO BS 5155 & IS 13095/1996) AND WITH 5 YEARS WARRANTY etc, complete complying with standard specification and as directed by SIPCOT Officers

150 mm dia.

100 mm dia.

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc, complete complying with standard specification and as directed by SIPCOT Officers

150 mm dia.

100 mm dia.

Sub Total of Total Amount in Column BA (ie. Qty x Unit Rate)

Added GST of 18%

P. MANICKAM AND CO (BID ID -1282096)