ADDN ALTN TO BLDG NO 10 11A OF SOUTHERN COMMAND AT PUNE

Amount

NOTE: Schedule ‘A’ Part I to XI are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-13 only.

Total amount of Sch 'A' Part-I (Building Works)

Total amount of Sch 'A' Part-II (Internal Electric Supply)

Total amount of Sch ‘A’ Part III Internal Water Supply

Total amount of Sch ‘A’ Part IV Refrigeration and Summer appliances

Total amount of Sch ‘A’ Part V (External Water Supply)

Total amount of Sch ‘A’ Part VI (External Electric Supply)

Total amount of Sch ‘A’ Part VII (Sewage Disposal)

Total amount of Sch ‘A’ Part VIII (Area Drainage)

Total amount of Sch ‘A’ Part IX (Excavation, Earthwork & Site Clearance)

Total amount of Sch ‘A’ Part X (Demolition/Dismantling)

SCH 'A PART XII (Miscellaneous B/R , E/M works,Special Repair Works) Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

S & F for ceiling fan down rods 1.0 M Long of 15 mm dia GI pipe to the existing trusses of any height including necessary welding & fixing with clamps and nut bolts etc complete all as specified and as directed.

S & F for ceiling fan down rods 1.5 M Long of 15 mm dia GI pipe to the existing trusses of any height including necessary welding & fixing with clamps and nut bolts etc complete all as specified and as directed.

S & F for ceiling fan down rods 2.0 M Long of 15 mm dia GI pipe to the existing trusses of any height including necessary welding & fixing with clamps and nut bolts etc complete all as specified and as directed.

S & F for fan hook/ U clamp made out of mild steel flat iron bend to required shape including necessary welding as per site requirements for hanging the ceiling fans with bolts, washers and nuts etc complete all as specified and as directed.

S & F for MCCB tripple pole and neutral rated capacity 63 A, 415V breaking capacity 25 KA of Make as given in Appx 'C' complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 63 A, 415V breaking capacity 10 KA of Make as given in Appx 'C' complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 32 A, 415V breaking capacity 10 KA of Make as given in Appx 'C' complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 5 to 32 A, 240 V breaking capacity 10 KA of Make as given in Appx 'C' complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 A, 240 V breaking capacity 10 KA of Make as given in Appx 'C' complete all as specified and as directed.

S & F wall mounted LED batten for surface applications anodised and extruted aluminium housing hightransmissivity diffuser high lumen out put of 20 watts, complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make Bajaj Cat part No BCLAB 20w or its equIvalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for recess mounted 2' x 2' square LED panel 36 watts, 596 x 596 x 9mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed. Make- Bajaj Cat part No - BCTBLR 36W FP WHN or its equivalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for Decorative wall mounted luminaire with single arm and decorative glass shade with suitable holder for LED bulb and provosion of LED bulb 10 watts of Make as given in Appx 'C' complete all as specified and as directed.

S & F for Decorative wall mounted luminaire with double arm and decorative glass shade with suitable holder for LED bulb and provosion of LED bulb 10 watts of Make as given in Appx 'C' complete all as specified and as directed.

S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Cat Part No BCLSB 10 NW or its equivallent model of Make as given in Appx 'C'

S & F Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :- Bajaj Cat No BIBWP 10W LED or its equvalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for LED 6 W spot light round, decorative recess mounted all as per Cat Part No Lumeno LED Spot 6W 3000K complete all as specified and as directed. Make :- Bajaj Cat No BRDCSL 6W WH LED or its equvalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for LED 12 W focus spot light round for picture focussing, decorative surface mounted LED Spot 12W 3000K of Make as given in Appx 'C' complete all as specified and as directed.

S & F for LED down light recess mounted luminare, round type 15 watts with efficiency of 100 lumens per watt, sleek design aluminium housing polycarbonate diffuser white finish operating voltage 150 V-270 V AC, 50 Hz all as per Cat Part No BZSLO 15W NW PRO of Make- Bajaj or its equavalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for LED down light recess mounted luminare, round type 18 watts with efficiency of 100 lumens per watt, sleek design aluminium housing polycarbonate diffuser white finish operating voltage 150 V-270 V AC, 50 Hz all as per Cat Part No BZSLO 18 W NW PRO of Make- Bajaj or its equavalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for LED 12 W mirror light, decorative surface mounted 3000K of Make as given in Appx 'C' complete all as specified and as directed.

S & F for Decorative suspended circular LED luminaire round type Make bajaj Cat No BXTAP 30 W or equivalent Make as given in Appx 'C' complete all as specified and as directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade required dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Bajaj Cat part No - BCLST 25W LED or its equivalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap complete all as specified and directed

S & F for plastic body exhaust fan, AC single phase, 240 V of size 200 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. Make - Bajaj Cat Part No -Maxma DX 8" or its equivalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for plastic body exhaust fan, AC single phase, 240 V of size 250 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. Make - Bajaj Cat Part No -Maxma DX 10" or its equivalent in makes given in Appx 'C' complete all as specified and as directed.

S & F for ceilling fan single phase, 230 volts, 50 Hz, 1200 mm sweep and connecting up with cable from ceiling rose or connector to fan, BEE 5 star rated, ISI marked complete all as specified and directed.

S & F for wall mounted fan single phase, 230 volts, 50 Hz, 400 mm sweep and connecting up with cable from ceiling rose or connector to fan complete all as specified and directed.

Fixing only serviceable light fitting like chandilier of any description, recessed light fitting etc complete all as specified and as directed.

M & L for taking out Split type air conditioner indoor and outdoor unit complete with copper tubing of any size and make for shifting at other place after making necessary opening size, cutting of wall any type/ thickness and fixing of AC after necessary servicing, making suitable arrangement for fixing of AC complete all as specified and directed.

Supply only capillary tube special annealed double wound copper tubing suitable for 1.5/1.8/2 ton split type air conditioner of diameter 0.25 " bore as per existing complete all as specified and directed.

Supply only capillary tube special annealed double wound copper tubing suitable for 1.5/1.8/2 ton split type air conditioner of diameter 0.38" bore complete all as specified and directed.

M & L for chemical earthing complete copper electrode buried directly in ground vertically connecting to copper earth srtip 20 x 3 mm thick by means of bolts, nuts, check nuts, and washers of copper including 40 mm dia medium grade protection pipe for earth lead PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate No 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion.

S & F for Highly efficient LED Bulbs, 3/5 watts, used as a ready replacement for existing GLS/CFL direct fit lamp,in E-27 cap (small/ big thred type) as per site requirement complete all as specified and directed.

S & F for PVC cable tray of size 100 x 100mm perforated type to be foxed on wall/ ceiling as required at site complete as all specified and as directed.

S & F for telephone socket 2G complete as all specified and as directed.

S & F for TV socket complete as all specified and as directed

S & F for Modular blank plate complete as all specified and as directed

S & F for exhaust fan AC single phase 230 /240 Volts,50 HZ,70 Watt input, of size 450 mm sweep, 900 RPM, metal body including with Louvers & provision of cable from ceiling rose to fan of Make as given in Appx 'C' complete all as specified and directed

S & F for exhaust fan AC single phase 230 /240 Volts,50 HZ,70 Watt input, of size 300 mm sweep, 900 RPM, metal body including with Louvers & provision of cable from ceiling rose to fan of Make as given in Appx 'C' complete all as specified and directed

Supply and fixing desert cooler electric driven (single phase), plastic/ PVC body having nominal air flow capacity of 4700 Cum per hour or nearest size complete all as specified and directed.

Supply and fix voltage stablizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 volts to 250 volts with out put voltage stablized at 230 volts with accuracy of + 2.5% and capacity 2 KVA suitable for above water cooler complete all as specified and directed.

Supply and fix voltage stablizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 volts to 250 volts with out put voltage stablized at 230 volts with accuracy of + 2.5% and capacity 1.0 KVA suitable for Refrigerator complete all as specified and directed. .

Taking up or taking down 80 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S & F 150mm Cast iron sluice valve with stainless steel spindle and cast iron hand wheel complying with IS:14846-2000, class PN 1.6 both ends flanged with 2 Nos rubber insertion gasket joints, nuts, bolts & washers of required size & Nos complete including removing of old unsv one complete all as specified and directed.

S & F 100mm Cast iron sluice valve with stainless steel spindle and cast iron hand wheel complying with IS:14846-2000, class PN 1.6 both ends flanged with 2 Nos rubber insertion gasket joints, nuts, bolts & washers of required size & Nos complete including removing of old unsv one complete all as specified and directed.

S & F 80mm Cast iron sluice valve with stainless steel spindle and cast iron hand wheel complying with IS:14846-2000, class PN 1.6 both ends flanged with 2 Nos rubber insertion gasket joints, nuts, bolts & washers of required size & Nos complete including removing of old unsv one complete all as specified and directed.

Supply, Laying, jointing & testing of 150mm dia Ductile iron (DI), pressure pipes with spigot and socket ends, centrifugally cast, class K-9, with cement mortar lining in inner side as per IS:8329/2000 (latest revision) and other relevant standards and metallic zinc coating followed by a finishing layer of epoxy paint in outer side, suitable for push on joint (rubber gasket joint) in any length with inside cement mortar lining laid in trenches complete all as specified and directed.

Supply, Laying, jointing & testing of 100mm dia Ductile iron (DI), pressure pipes with spigot and socket ends, centrifugally cast, class K-9, with cement mortar lining in inner side as per IS:8329/2000 (latest revision) and other relevant standards and metallic zinc coating followed by a finishing layer of epoxy paint in outer side, suitable for push on joint (rubber gasket joint) in any length with inside cement mortar lining laid in trenches complete all as specified and directed.

M & L for connecting pieces one end flanged and other end socket or spigot and bell mouth pieces one end flanged other end tapering as bell mounth, DI Bends tapers, Tees, pieces (Single or double branch) any Type and angle/ radius and straight connecting pieces for DI Pipe upto 150 mm bore complete all as specified and as directed.

M&L construction of Brick Masonry Valve Pit of internal dimension 900x900x900mm, one Brick thick wall in cement mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggregate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40X5mm Flat Iron Frame alround including provision of Hinges, Handle and Locking Arrangement and 40 x 40 x 6mm Angle Iron Frame fixed on Top of Valve Pit by means of Holdfast 150mm long, embedded in PCC 1:2:4 (20mm graded aggregate) Block of size 230 x 200 x 100 mm, applying two coats of Anti-corrosive Paint over a coat of Red Oxide Zinc Chrome Primer after preparation of all exposed to Steel Surfaces including necessary Earth Work in Soft/Loose Soil and demolition of old unserviceable Valve Pit complete all as specified and as directed.

M&L construction of Brick Masonry Valve Pit of internal dimension 750x750x900mm, one Brick thick wall in cement mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggregate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40X5mm Flat Iron Frame alround including provision of Hinges, Handle and Locking Arrangement and 40 x 40 x 6mm Angle Iron Frame fixed on Top of Valve Pit by means of Holdfast 150mm long, embedded in PCC 1:2:4 (20mm graded aggregate) Block of size 230 x 200 x 100 mm, applying two coats of Anti-corrosive Paint over a coat of Red Oxide Zinc Chrome Primer after preparation of all exposed to Steel Surfaces including necessary Earth Work in Soft/Loose Soil and demolition of old unserviceable Valve Pit complete all as specified and as directed.

M&L construction of Brick Masonry Valve Pit of internal dimension 450x450x450mm, one Brick thick wall in cement mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggregate) in Foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS Sheet Valve Pit Cover, welded with 40X5mm Flat Iron Frame alround including provision of Hinges, Handle and Locking Arrangement and 40 x 40 x 6mm Angle Iron Frame fixed on Top of Valve Pit by means of Holdfast 150mm long, embedded in PCC 1:2:4 (20mm graded aggregate) Block of size 230 x 200 x 100 mm, applying two coats of Anti-corrosive Paint over a coat of Red Oxide Zinc Chrome Primer after preparation of all exposed to Steel Surfaces including necessary Earth Work in Soft/Loose Soil and demolition of old unserviceable Valve Pit complete all as specified and as directed.

Supply and Laying 3.5core x 185sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

Supply and Laying 3.5core x 150sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

Supply and Laying 3.5core x 50sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

Supply and Laying 3.5core x 35sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

Supply and Laying 4core x 25sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

Supply and Laying 4core x 16sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

Supply and Laying 4core x 10sqmm XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, with necessary end terminal /cable gland as per site requirement including necessary connecting to the main switches /cut outs MCB/MCCB with necessary lugs after cutting to required length of cable in trench/ walls complete all as specified and directed .

S & F Energy saving new generation environmental friendly long life versatile presure die cast housing and heat sink in aluminium extrusion IP 66 flood light fitting luminaire with secondary optics, high power LEDs as light source and electronic driver of capacity 160 watts with pre wired suitable for sports lights and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including removal of old unserviceable on complete all as directed by Engineer-in-Charge. Make Bajaj Cat part No BARFEG 160W LED or its equivalent in makes as given in Appx 'C' complete all as specified and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast housing and heat sink in aluminium extrusion IP 66 flood light fitting luminaire with secondary optics, high power LEDs as light source and electronic driver of capacity 120 watts with pre wired suitable for sports lights and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including removal of old unserviceable on complete all as directed by Engineer-in-Charge. Make Bajaj Cat part No BJFL 120W LED or its equavalent in in makes as given in Appx 'C' complete all as specified and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast housing and heat sink in aluminium extrusion IP 66 flood light fitting luminaire with secondary optics, high power LEDs as light source and electronic driver of capacity 80 watts with pre wired suitable for sports lights and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including removal of old unserviceable on complete all as directed by Engineer-in-Charge. Make Bajaj Cat part No BJFL 80W LED or its equavalent in makes as given in Appx 'C' complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted complete all as specified and directed.

S & F Integral decorative LED bollard with opal acrylic with IP 65 protection suitable for 9 watts LED bulb with necessary elecrical connections with adequate size of Nuts and Bolts including taking down existing unserviceable one, complete as all specified and as directed. Make: Bajaj Cat part No BGBOS 600 9W LED or its equavalent in makes as given in Appx 'C' complete all as specified and directed.

Material and labour for RCC Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for 150 users etc.complete all as specified and as directed

Material and labour for Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats, complete of size 2.4 M dia X 3.0 M deep complete all as specified and as directed

M & L for PCC 1:4:8 type D2 using 40 mm graded aggregate in foundation , mass concrete, sub base complete all as specified and directed.

Use & Waste for finished flat surfaces formwork to sides of concrete foundations, footings , bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

Use & Waste for rough finished surfaces formwork to sides and soffits of chajjas thick (horizontal or sloping if any) of similar work vertical or to batter complete all as specified and directed.

Use & Waste for rough finished surface square rectangular or polygonal formwork to sides of pillars, posts, struts, piers , columns and stanchions complete all as specified and directed.

M & L for rough finished surfaces formwork to sides and soffits of floor beam, beam landings haunchings girders, bressumers , lintels, cantilevers , shelves including supports, overhangs etc also splays between floors and beams etc. complete all as specified and directed.

Material and labour for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending hooking etc & binding with mild steel binding steel wire (annealed) not less than 0.9mm dia conforming to Fe-500D complete all as specified and directed.

Material and labour for TMT bars 6 to 8mm dia cut to length bent to shape required, including cranking, bending hooking etc & binding with mild steel binding steel wire (annealed) not less than 0.9mm dia conforming to Fe-500D complete all as specified and directed.

Material and labour for TMT bars 5mm dia and over upto and including 10 mm dia in stirrups cut to length bent to shape required, including cranking, bending hooking etc and including binding with mild steel binding steel wire (annealed) not less than 0.9mm dia conforming to Fe-500D complete all as specified and directed.

Material and labour Reinforced Cement Concrete (design mix) M-25 grade for Columns, Pillars, Piers, Posts and struts complete all as specified and directed.

Material and labour Reinforced Cement Concrete (design mix) M-25 grade for foundations , including rafts, footings , foundation beams, plinth beams, bases for columns , etc basement slabs , underreamed piles and mass concrete complete all as specified and directed.

Material and labour Reinforced Cement Concrete (design mix) M-25 grade for chajjas complete all as specified and directed.

Material and labour Reinforced Cement Concrete (design mix) M-25 grade for beams, cantilever, bressumers , lintels over 1.5 m span complete all as specified and directed.

Material and labour Reinforced Cement Concrete (design mix) M-25 grade for beams, cantilever, bressumers , lintels upto 1.5 m span including form work complete all as specified and directed.

Material and labour Brick work with fly ash bricks, old size bricks (Non modular, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Material and labour Brick work with fly ash bricks, old size bricks (Non modular, straight or curved on plan exc 6m mean radius,in half brick thick wall built in cement mortar 1:4 all as specified and directed.

Material and labour for 15mm thick cement plastering on internal walls in CM 1:6 on brick or concrete surfaces finished even & smooth (without using extra lime or cement) complete all as specified and directed.

Material and labour for 15mm thick cement plastering two coats (10mm + 5mm) on external walls in CM 1:4 on brick or concrete surfaces finished even and smooth with sponge finish using water proofing compound @3% complete all as specified and as directed.

Supply only Integral waterproofing compound complete all as specified and directed.

Material and labour for mild steel rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming Yst 310 Grade as per IS 4923 (1997) complete all as specified and directed.

Supply and Fixing for mild Steel work in rectangular tube section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Yst 310 Grade as per IS 4923 (1997) complete all as specified and directed.

Material and labour for Steel work in tubular round or rectangular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 of Yst 310 Grade, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Supply and Fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm and n exc 15cm long and Diameter of neck in mm 11 to 15 mm complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description over 10cm girth or width not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing 0.63mm thick, CGI sheet for roofing ridges valley gutters, drip and straight flashing with grade of zinc coating complete all as specified and directed.

Ditto here-in-before but except sheeting complete all as specified and directed.

Material and labour for clay roof tiles Mangalore pattern , double locking /groove , glazed of Make -Albuquerque / Monier Colour Plus interlocking at side joints including laid dry complete all as specified and directed.

M&L for clay ridge or hip tiles to suit mangalore pattern , double locking /groove , glazed of Make -Albuquerque / Monier Colour Plus of roofing tiles , bedded and jointed in cement mortar 1:6 complete all as specified and directed.

Supply and Fixing 0.63mm thick, plain, galvanised, mild steel sheeting, in ridges valley gutters, drip and straight flashing with grade of zinc coating 275 complete all as specified and directed.

Supply and Fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws with two corrugation side lap, bent to shape complete all as specified and directed.

M & L for nonmetallic rainwater gutter system alongwith all accessories / fittings and plastic downpipe/ spout ( model no K 35 )complete all as spoecified and directed Make : Monier LUXRON or equivalent modular design and material as aprooved by GE complete all as specified and directed.

M & L for 15 mm thick and 1195 mm X 1195 mm size Anutone soft subtex nubby or equivalent including Main T MT15W36 ,Cross T CT15W12,Cross T CT15W06 and Wall Angle WA15W30 (L) fixed to wall for false ceiling including necessary supporting as per manfucaturers instructions for securing frame work for ceiling suspended. complete all as specified and directed . (Note:1 . The height of the ceiling is above 5meter). Note:2. Design of Anutone soft subtex nubby of ceiling boards as approved by GE complete all as specified and directed.

Material and labour for decorative (pattern and design of false ceiling to be approved by GE) false ceiling with 10mm thick 600x900mm plaster of paris sheets fixed with machine screws on GI channel 18 gauge thick grid work, main joists placed at 750mm centers, secondary joists placed at 450mm centers, GI angle suspenders from roof and treating the plaster of paris sheets with thin layer of POP with Gypsum binder, sanding the surfaces till smooth surface is obtained including preparation of surface and applying two coats of oil bound distemper complete all as specified and directed.

Material and labour for Plaster of paris decorative cornices/ moulding to the pattern as approved by Engineer in Charge of cross sectional dimension exc 13 Sqcm and n.exc 25 Sqcm and fixed in decorative pattern including preparation of surfaces and applying two coats of oil bound distemper over a coat of primer matching with the colour of ceiling complete all as specified and directed.

Material and labour for 1st class H.W. timber scantling, fixed clean sawn as in rafters, purlins etc.complete all as specified and directed.

Ditto as above but except timber scantling complete all as specified and directed.

Material and labour cement fibre board Eves/Weather Boarding 15 to 20mm thick or Feather Edged 15mm to 20mm thick and fixed with 30mm Lap, complete approved arch pattern any size and shape all as specified and as directed.Make: Shera wall/Everest.

Material and labour for 18mm thick plywood BWR grade type BB fixed with fevicol and nails for working table / storage almirah/wall panelling or ceiling board to the size and pattern as shown in Drg or as directed by GE complete all as specified and directed.

Material and labour for 12mm thick plywood BWR grade type BB fixed with fevicol and nails for working table / storage almirah/wall panelling or ceiling board to the size and pattern as shown in Drg or as directed by GE complete all as specified and directed.

Material and labour for 06mm thick plywood BWR grade type BB fixed with fevicol and nails for working table / storage almirah/wall panelling or ceiling board to the size and pattern as shown in Drg or as directed by GE complete all as specified and directed.

Material and labour for 0.90mm thick decorative laminate type-I of surface finish (colour & pattern as approved) fixed with approved adhesive as per manufacturer’s instruction finished to approved size for working table/ wall panelling/ ceiling board complete all as specified and directed.

Material and labour for 4mm thick one side decorative match veneer in wall/ ceiling with melamine polishing complete all as specified and directed.

Material and labour for Ist class H.W. plain cover fillets square, rectangular or triangular in section bull nosed, splayed chamfered or rounded on one edge or face in sectional area n. exc. 6 Sqcmcomplete all as specified and directed.

Material and Labour for Ist class H.W. plain cover fillets square, rectangular or triangular in section bull nosed, splayed chamfered or rounded on one edge or face in sectional area exc. 6 Sqcm and not. exc 13 Sq cm complete all as specified and directed.

Material and labour for Ist class H.W. plain cover fillets square, rectangular or triangular in section bull nosed, splayed chamfered or rounded on one edge or face in sectional area exc. 13 Sqcm and not. exc 25 Sq cm complete all as specified and directed.

Supply and Fixing brass hinges 75mm size extruded with stainless steel pin type D-11 complete all as specified and directed.

Supply and Fixing brass cup board lock 75mm size 4 level with duplicate keys complete all as specified and directed. Make:Godrej or equivalent

Supply and Fixing brass handles extruded fabricated type 100mm size complete all as specified and directed.

Supply and Fixing brass powder coated 'D' bracket suitable for 10mm thick glass complete all as specified and directed.

Supply and Fixing 10mm thick glass with crystal polish complete all as specified and directed.

Supply and Fixing CP brass magnetic catch as in cupboards complete all as specified and directed. Make:Godrej or equivalent

Material and labour for stainles steel drawer slider alongwith sliding wheel of standard make and 600mm long conforming to sample kept in GE office complete all as specified and directed. Make:Godrej or equivalent

Material and labour for complete removal of existing treatment on walls using steel wire brush/ sanding machine, rubbing ivory papers etc and washing , rubbing down and stopping of distempered and painted surfaces, complete all as specified and directed.

Material and labour for complete removal of existing treatment on ceiling using steel wire brush/ sanding machine, rubbing ivory papers etc and washing , rubbing down and stopping of distempered and painted surfaces, complete all as specified and directed.

Preparation of surfaces by applying wall care putty 2-3 mm thick on walls surfaces , filling cracks by crack filler and smoothen the surfaces with using sand paper etc ccomplete all as specified and directed.

Preparation of surfaces by applying wall care putty 2-3 mm thick on ceiling surfaces , filling cracks by crack filler and smoothen the surfaces with using sand paper etc complete all as specified and directed.

Material and labour for two coats of acrylic distemper new surfaces over a coat of primer of approved tint on wall surfaces complete all as specified and directed.

Material and labour for two coats of acrylic distemper new surfaces over a coat of primer of approved tint on ceiling surfaces complete all as specified and directed.

Material and labour for applying two coats of luster paint over a coat of primer to wall surfaces complete all as specified and directed.

Material and labour for applying two coats of luster paint over a coat of primer to ceiling surfaces complete all as specified and directed.

Material and labour for applying two coats of plastic emulsion paint over wall surfaces complete all as specified and directed.

Material and labour for applying two coats of plastic emulsion paint over ceiling surfaces complete all as specified and directed.

Material and labour for applying metallic royal texture paint over a basecoat over a coat of primer over wall/ ceiling surfaces complete all as specified and directed.

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or equivalent in makes as given in Appx 'C' , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

Preparation of old treated plastered/ false ceiling surface of ceiling by filling cracks by crack fill paste of Berger or equivalent in makes as given in Appx 'C' , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

Preparation of old surface of wall/ceiling by filling cracks by crack fill paste of Berger or equivalent in makes as given in Appx 'C' , removing loose paints etc , removing nails etc and making good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of luster paint complete all as specified and as directed.

Preparation of old surface of wall by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and make good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Preparation of old surface of ceiling by filling cracks by crack fill paste of Berger or equivalent make , removing loose paints etc , removing nails etc and making good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalentin makes as given in Appx 'C' )complete all as specified and as directed.

Material and labour for applying two coats of weather proof exterior emulsion paint ('APEX' brand of Asian or equivalent in makes as given in Appx 'C' ) wall etc, over a coat of primer complete all as specified and as directed. (Note: height of building exceeding 5m) complete all as specified and directed.

Material and labour for preparation of old plastered or unplastered surfaces and applying one coat of cement base paint complete all as specified and directed.

Material and labour for preparation of new wooden walls/ window/ railing/ flooring/ wall pannelling/door surface by applying resin pigment and hardner to desired colour and pattern and applying two coats of melamine polish using spray gun complete till fine glossy finish is obtained complete all as specified and directed.

Material and labour for French polishing on wooden surface of any description including cleaning and preparing the surfaces with a coat of wood filler and two or more coats of French polishing till the desired finish is obtained complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description over 10cm girth or width and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of wood surfaces and wood based material new or old of any description and girth not other wise described and treated with two coats of creosote complete all as specified and directed.

Material and labour for preparation of new wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Material and labour for preparation of old surfaces of wood and wood based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for cutting chases, pinning in making good to face for concealed water tubing complete all as specified and directed.

Supply and Fixing in repair Continental / Queens Series, brass chromium plated for towel rack 24” Make - Jaguar complete all as specified and directed.

Supply and Fixing in repairs, vitreous china, full stall type urinal with urinal censor complete with necessary fittings all as specified and directed. Make :– Hindware, Senso Art Cat No 60018 Star white or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Supply and fixing in repairs Two way bib cock with wall flange 15mm dia Cat No. 7041 jaquor Make : Jaguar of Queens series Continental or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Supply and fixing in repairs Angular stop cock Cat No. 7053 Make : Jaguar of Queens series Continental or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Supply and Fixing in repair CP Brass long body bib cock MQT 512 15mm of make Jaguar or equivalent in makes as given in Appx 'C' complete all as specified and directed

Towel ring Cat No. 7721 of Jaquar or equivalent make of Cera complete all as specified and directed.

Toilet paper holder Cat No. 7751 of Jaquar or equivalent as given in Appx 'c' complete all as specified and directed.

Central hole Basin mixer with POPup waste system with 450mm long braided hoses Cat No. 169KNB of Jaquar complete all as specified and directed.

Pillar cock Cat No. 7011 of Jaquar or equivalent as given in appx 'c' complete all as specified and directed.

Supply and Fixing in repairs CP wall mixer 3-in-1 system with provision for both telephonic shower and overhead shower complete with wall flange with 115mm long bend pipe ,Cat No. 7281 of make Jaquar ‘QUEEN'S COLLECTION' Series or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Supply and Fixing vitreous chinaware EWC including connection to drain or outgoing pipe and to PVC flushing pipe, antisyphonage pipe, PVC low level flushing cistern 10 ltr capacity with brackets of approval Make and all necessary fittings etc complete all as directed and specified incl PVC seat cover fixed in repair complete all as specified and directed.

Material and labour for vitreous china coloured counter type wash basin fixed over granite top and vertical sides with full round edge polish to exposed edges, including cuddapa stone slab on top and vertical sides with CP waste coupling, chain and plug, waste fitting, union and waste pipe 32mm dia of required length and all necessary inlet and outlet connections complete all as specified and directed. Make of wash basin :– Hindware, Zen Cat No 10049 or equivalent model in makes as given in Appx 'C' complete all as specified and directed.

Supply and Fixing in repair vitreous china wash down water closet (pedestal pattern) cascade type ‘P’ trap, in built seat cover and flushing cistern, low level, valveless, symphonic action type complete with inlet ball valve, float and handle as per catalogue No. S1013109, catalogue No. S1013110 catalogue No. S1013111 cistern (complete set) of Cera/Campbell or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Supply and fix in repairs, stainless steel plate rack of size 36inch x 31inch x 10inch, made out of 0.63mm thick stainless steel sheet (Grade AISI 304 18/8), stainless steel screws and round pipe, fixed to wall with screws complete all as specified and as directed. Make – Blue Star Silver Shine Cat No.KPR-315 or equivalent from Nirali/ Jain Brothers Sanitation Pvt Ltd (Jayna) as approved by GE complete all as specified and directed.

Material and labour for providing and fixing toilet fittings brass chromium plated for Health faucet brass body with wall hook and 1 metre ss braided rubber hose pipe Cat No.ALD CHRE 573 Make -Jaquor or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Exposed part kit of concealed stop cock with fitting sleeve, operating lever& adjustable wall flange with seal(compatible with ALD083 & ALD089) SKU: FLR-CHR-5083NK or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Bottle trap Jaquar cat No. ALD_CHR-769L 250x190 or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Automatic soap Dispenser 0.80 liters cap Aluminium/ABS, finish- chrome/black Jaquar Cat No. DJ0160AS or equivalent in makes as given in Appx 'C' complete all as specified and directed. .

Flush plate for EWC (control plate Riviera SKU:Jaquar Cat No. CIS-CHR-31185210X or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Concealed flush tank single piece slim concealed cistern with wall mounting frame, installation kit and S type drain pipe connection set for wall hung WC(with out flush control plate) jaquar cat No. JCS-WHT-2400WS or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Supply and Fixing Auto hand dryer HK-1600EA-ABS body Make:Toshi or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Material and labour for vitreous china table top wash basin fixed over granite top and vertical sides with full round edge polish to exposed edges, including cuddapa stone slab on top and vertical sides with CP waste coupling, chain and plug, waste fitting, union and waste pipe 32mm dia of required length and all necessary inlet and outlet connections complete all as specified and directed. Make of wash basin :– JAQUAR Cat No JDS-WHT-25901 or equivalent model in makes as given in Appx 'C' complete all as specified and directed.

Supply and Fixing Ist class hardwood (TEAK)Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Material and labour for 40 mm thick 1st class HW (Teak wood) designer, framed, panelled shutters (any number of panels), with panel of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats including two coats of melamine polish matt finish complete all as specified and directed.

Supply and Fixing 40mm thick flush shutter with solid core construction with block board core and plywood face panel commercial type on both faces including second class hard wood plain cover fillets 35x6mm all around the shutterscomplete all as specified and directed.

Supply and Fixing Factory made solid PVC Moulded door wood grain printed shutter 28- 30 mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face and 2mm prelam PVC sheet on back face, with particle board core including supplying and fixing in frame at site as per specification and drawing given in SSR-2010 part I and II complete all as specified and directed.

Solid PVC door frame of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match the colour with printed sheet PVC sheet reinforced with MS Square tube supplying and fixing in opening as per specification and drawing, given in SSR-2010 part I and II complete all as specified and directed.

Supply and fix in repairs 300mm long antique brass sliding door bolts with sand or die cast brass hasp, staple (bolt type) and fixing bolt with roller or drawn brass bolts, ISI marked, complete all as specified and as directed.

Supply and fix for butt hinges, extruded brass, 200mm size, with stainless steel hinge pin, bright polished complete all as specified and as directed.

Supply and fix in repairs 200mm long, antique brass barrel tower bolt, with cast or sheet barrel and rolled or cast bolt all complete as specified and as directed.

Supply and fix in repairs150mm size antique brass handles, extruded, fabricated type, polished complete all as specified and as directed.

Supply and fix for Brass powder coated 25mm bore in curtain rod decorative/Antique type section alongwith decorative caps at both ends as approved complete all as specified and as directed.

Supply and fix for Brass decorative/antique rod brackets to suit the curtain rod of 25mm bore, complete all as specified and as directed.

Supply and Fixing aluminium Powder coated three track sliding window with two shutters of 4mm thick float glass and one shutter of stainless steel wire mesh including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified. :-Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604 (using Jindal Sec) or equivalent.complete all as specified and directed.

Material and labour for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section including glass and stainless steel wire mesh etc complete all as specified and directed.

M & L for water proofing treatment to RCC roof slab as specified below and as directed by Engineer-in-Charge :- (a) 10 mm th cement plaster in CM 1:3 with integral WPC to be laid over the RCC roof slab when the concrete is green. (b) Applying a uniform coat of bitumen primer @ 0.70 kg/sqm over cement plaster. (c) 3 mm th plain texture and weighing not less than 3.6 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen based prefabricated five layer water proofing membrane reinforced with non woven polyster matt black finished over a coat of hot blown bitumen of 85/25 and torch application of membrane with overlap while torching shall be 150 mm on length side and 100 mm on width side. after necessary preparation of surface complete as per manufacturers instructions. (d) Apply two coats of bitumastic - aluminium paint over the membrane. complete all as specified and directed.

M& L for ATT at bottom and sides of excavation at the rate of 05 ltrs of emulsion per Sqm of surface area complete all as specified and directed.

M& L for ATT at backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of the sub structure in contract with backfill to be measured) complete all as specified and directed.

M& L for ATT at Top surface of filled earth at the rate of 05 Ltrs of emulsion Per Sq.m of surface area complete all as specified and directed.

M& L for ATT at the soil under plinth protection at the of 5 litres of emulsion per suqare metre of surface area. complete all as specified and directed.

M& L for ATT treating the soil along with external perimeter of building at the rate of 2.25 ltrs of Emulsion per metre of perimeter wall complete all as specified and directed.

M & L for providing and injecting chemical emulsion for post constructional Anti-termite treatment along external perimeter wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per Sqm of the vertical surface of the sub-structure to a depthof 300mm including excavating channel along the wall and rodding etc complete all as specified and directed.

M& L along the perimeter wall below concrete or masonry apron using chemical emulsion @2.25 litresper linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

M& L treatment of soil under existing floors using emulsion @ one litre per hole , 300mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand ) to match existing floors complete all as specified and as directed.

Material and labour for voids using chemical emulsion one litres per hole at 300mm intervals incliding drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floors complete all as specified and directed.

M& L at points of contact of wood work by chemical emulsion (in oil or kerosene based solution ) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same ter wall below concrete or masonry apron using chemical emulsion @2.25 litresper linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

Plain/ Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating as directed, (The rates quoted for the item are inclusive of form work) complete all as specified and directed.

M & L for moorum filling in floors or pavings , laid in layers n exc 15 cm thick,spread, levelled and blinded with eart nad rammed including watering complete all as specified and directed.

Material and labour MS plates ,plain or chequered etc complete all as specified and directed.

Material and labour except timber for Ist class H.W. timber scantling clean sawn as in roof complete all as specified and directed.

Material and labour for laminated wood textured flooring in planks of 8 mm (32 crystal) with interlocking arrangement having unique glue used click system and fixed over plastic sheet of 0.2 mm and foam under layer of 2 mm complete as per manufacturers instruction and as directed. Make : PERGO or equivalent in makes as given in Appx 'C' complete all as specified and directed.

Material and labour for coloured tiles 400mm x 400mm x 10mm thick of make "Johnson Endura" or equivalent as approved by GE, laid over and including 20mm thick screed bed in cement mortar 1:4, jointed and tiles to be fixed by using 6mm thick spacer and filled with matching coloured Epoxy Groute complete all as specified and directed.

Material and labour for coloured Non skid ceramic tiles of size 400x400mmx7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 20mm thick screed bed in CM (1:4) complete all as specified and directed.

Material and labour machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick screed bed in CM 1:6 including rubbing and mirror polishing complete all as specified and directed.

Material and labour hand cut kota stone slab flooring 20-25mm thick as in vertical surface such as skirting and dado jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including backing coat of 10 mm thick in cement mortar (1:4), including rubbing and polishing complete all as specified and directed.

Material and labour for Vitrified Ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 Sqm, but not exceeding 1.44 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including Screed Bed 15 mm thick in Cement Mortar (1:6) complete all as specified and as directed.

Material and labour for Vitrified Ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 Sqm, but not exceeding 1.44 Sqm, in vertical surfaces skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick in Cement Mortar (1:4) complete all as specified and as directed.

Material and labour green marble as in skirting/border including 10mm thick rendering in cement mortar 1:3 as in vertical surface etc complete all as specified and directed.

Material and labour granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform incl 15mm screed CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and directed.

Material and labour machine cut cudappah stone slab 30-40 mm thick complete all as specified and directed

Material and labour for coloured glazed ceramic tiles of size 300mm x 600mm x 7 to 8mm thick of colour and pattern as approved by GE, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Material and labour for coloured glazed ceramic highlighter tiles of size 600mm x 300mm x 7 to 8mm thick of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar (1:3) as in vertical surface etc complete all as specified and as directed.

Material and labour for coloured Non skid ceramic tiles of size 300x300mmx7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM (1:6) including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material and labour Hardcore of guage Broken stone n. exc 63mm deposited, spread and levelled in layers n exc 150mm thick, watered and rolled/ rammed to a true surface complete all as specified and as directed.

Material and labour for cement concrete 1:3:6 Type C-2 (using 40mm graded stone aggregate)75 mm thick in plinth protcetion and court yard, finished cement surfaces even and smooth without using extra cement complete all as specified

Material and labour for precast cement concrete glazed interlocking tiles,paver block, any shape and size as approved ,60mm thick, conforming to IS 15658-2006, M-35 grade in floor/pavement laid over 30mm thick sand cushioning .laid dry to the profile including vibrating with surface vibrator after laying of tiles all as specified and directed. NOTE: Manufacturers test certificate for crushing strength and Water absorption shall be submitted alongwith sample complete all as specified and directed.

Labour only for full round moulding to 18 to 20mm thick granite slab complete all as specified and directed.

Material and labour 10mm thick toughened glass with stainless steel (ozone fitting) frame fixed to walls/ railing as approved and omplete all as specified and directed.

Material and labour for cutting & Polishing of existing Granite/Marble/Kota stone with necessary machinery complete all as specified and directed.

Supply and install storage type electric water heater with high precision precalibrated thermostat, safety valve , preset thermal cutout , fire retardant power cord , ultra thick stainless steel inner tank , rust and shock proof ABS outer body non ferrous pressure plate , compact and easy to install colour changing LED indicator , copper heating elemet of of 50Ltr capacity with rated watttage 2KW,230volts , 50Hz of Temp range 35°C to 75°C ,working pressure 0.8 mpa including inlet and out connection PVC flexible pipe of Make as given in Appx 'C' complete all as specified and directed.

Supply ,fabrication ,installatiion & testing of LT panel board CPRI type tested indoor type ,worming proof double door front opening made out of CRCA sheet 1.6mm thick duly painted with powder coating synthetic enamelled paint over a coat of red oxide primer including wiring for controlling instruments and suitable for 500volts ,50Hz , fixed in wall including making of electrical connections with the following accessories:- (a) 400Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on Bakelite/DMC insulator bus bar support (square/round) insulators of suitable size and good insulation resistance-01 Set (b) 4 pole MCCB 200Amps 50Hz ,415V with rupturing capacity 36KA-01Nos(incoming) (c) MCCB 4 pole 63Amps ,Rotary handle adjustable Thermal Magnetic relay breaking capacity 16KA at 415Volts lcs=100% lcu-04Nos(outgoing). (d) 4 pole MCCB 40Amps,Rotary handle adjustable Thermal Magnetic relay breaking capacity 16KA at 415Volts lcs=100% lcu-05Nos(outgoing). (e) Isolator TPN 100 Amps -02 Nos (f) MCB SPN 32 amp- 40 NOS (g)VAF meter complete all as specified and as directed.

Removing of excavated demolished material, to appox 15KM including loading, unloading and stacking at destination, complete all as specified and as directed. (Note Demolished material considered herewith is items other than items considered under Sch of Credit as given in Sch A part XI )

United Sales Corporation

Horizon Construction

rawassa construction

VIRENDRA FABRICATORS

SUYOG CONSTRUCTIONS

KARNI BUILDERS