SPL REPAIR TO BLDG NO O-8/F3 AND ADDN/ ALTN AND PROVN OF TILING WALL PANELLING AND ALLIED FACILITIES IN OR FAMILY TRANSIT ACCN AT O-4/G/02 INSIDE FORT WILLIAM UNDER GE (FW) KOLKATA

Amount

Taking down cement plaster on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L rendering 15 mm thick cement plaster in two layer each of 10+5 mm thick on fair face of brick work or concrete surface in CM (1:4) & water proofing compound mixed with second layer @ 3% finished fair and even. complete all as specified and directed. (Note -W.P.C. shall be measured and paid separately )

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished rendering surfaces even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:3 on concrete as in ceiling/landing etc on concrete surface finish even and smooth without using extra cement with and including taking down cement or lime plaster of any description complete all as specified and directed.

Supplying Integral liquid water proofing compound.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L brick work with Fly ash bricks old size brick straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item no 07 above but except bricks complete all as specified and directed.

M&L brick work with Fly ash bricks' old size brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall complete all as specified and directed.

M&L for 15mm thick cement plaster in cement mortar 1:4 on bricks or concrete surface and finished even and smooth without using extra cement including necessary scaffolding work complete all as specified and directed.

M&L for cleaning new plastered surfaces of walls, soffits of chajja, roof slab etc, using emery paper, putty blade/scraper as applicable for removing corrosion, algae formation etc complete with one coat of putty ghola and applying two coats of weather proof exterior emulsion paint by using airless spray technology capable of operating single spray gun with hose of adequate length over one coat of exterior based primer with brush finished over 1mm thick exterior wall care putty including necessary scaffolding, safety and protective measures for upto 4 storey building height complete all as specified and directed.

M&L for cleaning old treated surface of wall, soffits of chajja, roof slab etc, with using high pressure jet washer including cleaning the surface by scarping as required using emery paper, putty blade/ scraper as applicable for removing loose paint, corrosion, algae formation etc complete with touch-up putty wherever required with applying two coats of weather proof emulsion paint by using airless spray technology capable of operating single spray gun with hose of adequate length over one coat of suitable exterior weather proof primer with Grago machine over 2 mm thick exterior wall care putty, including necessary scaffolding, safety and protective measures upto 4 story building height complete all as specified and directed.

M & L two coat of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour on newly plastered surface of new wall surfaces , by brush and roller including over a coat of suitable acrylic primer over 2 mm thick POP putty in two layers complete on wall complete all as directed by Engr-in-charge.

M/L for complete removal of existing treatment, washing, rubbing down and stopping of painted/treated surfaces and applying two coat of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour distemper by brush and roller including over a coat of suitable acrylic primer on wall complete all as directed by Engr-in-charge.

M & L preparation of new plaster surface of walls etc and applying three coats of white washing complete all as specified and directed.

Material & labour for preparing old decorated plastered surfaces of wall and applying two coat of white wash complete all as specified and as directed

M & L preparation of new plaster surface of ceiling etc and applying three coats of white washing complete all as specified and directed.

Material & labour for preparing old decorated plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed

Material & labour for preparing newly plastered surfaces of walls and applying two coat of cement based paint over cement wash with Portland cement slurry for smooth wall finish complete all as specified and directed

Material & labour for preparing old decorated plastered surfaces of walls and applying one coat of cement based paint complete all as specified and directed

Demolition of cement Concrete(reinforcement cut as required to facilitate demolition) Roof, floors (other than ground floors), beams, staircase, landing, chajjas and similar suspended work complete.

M & L RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall, beam and columns in floor, roof landing,, balconies, conopies, deck slab and shelves etc complete all as specified and directed.

M & L providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in landing, cover slab for manholes etc, chullah, hoods, chajjas, water trough, mangers, shelves, kerb stones and similar articles with plan face including chamfered weathering, throating etc including necessary use and waste of form work complete all as specified and as directed.

Use and waste of formwork to sides and soffits of suspended slabs, floor slab, landing and similar work n. exc. 200 mm thick rough finished on flat surfaces of concrete complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cracking, bending, spirally for hopping for columns hookings ends and binding with and incl mild steel wire (annealed) not less the 0.9mm dia or securing with clips complete all as specified and as directed.

S & F mild steel deformed bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L non skid ceramic colour tiles of area of each tile exc .06 Sqm but n exc exc .11 Sqm and 6 to 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10mm thick backing coat in CM 1:4 complete all as specified and directed .

M&L non skid ceramic colour tiles of area of each tile exc .11 Sqm but n exc exc .18 Sqm and 6 to 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed. all as specified and directed .

M & L glazed ceramic colour tiles size 450 mm x 300 mm x 6 to 7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement including 10 mm thick plastering in cement mortar 1:4 complete all as specified and directed. to match complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M & L for 20 mm thick dubbing coat over uneven surfaces of brick wall or concrete surface in cement mortar 1:4 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut one side polished natural hard stone (Granite)any type in step, jambs, pillars, window cills, cooking plate from and similar places etc like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismantling of plain or corrugated sheeting , any gauge, thickness and including Naintital or similar pattern roof coverings complete all as specified and directed.

S & F pre-painted galvatume aluminium zinc coating GI based corrugated steel 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S & F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges , valley gutter, Sun shed etc fixed with self tapping screws as specified.

Dismantling cast iron work of any description complete all as specified and as directed.

Supply and fixing for structural steel work Fe 410-W (Gde-E-250) rolled mild steel in joist, channel, angle or Tee section fixed independently etc up to height 4 to 6 mtr from each floor level (cut to ordinary length ie. Within 20mm of the length indicate) Gde Fe-410-W-(Gde-E-250) Quality-B including using former iron props and steel plates to existing RCC over head members like beams, slabs etc so as to ensure safety of existing structure and floor during repairing works complete all as directed by Engr-in-Charge. Note: The section to be provided under this item will be used as beam to support floor/roof.

S & F in repair rotational moulded polyethylene water storage tanks, of 500 litres capacity vertical, cylindrical, with close top black in colour, two layered wall construction ISI marked hoisted & fixed in position complete all as specified and directed.

S & F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-1991,complete all as specified and directed.

S & F 20 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe (Minimum weight 210 gms), complete all as specified and directed.

S & F 25 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe (Minimum weight 210 gms), complete all as specified and directed.

Demolition of cement concrete (un-reinforced) not exc 15cm thick in ground floor and paving (below or above ground level) complete all as specified and directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring benching to drain, coping, etc and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and as directed.

Extra for forming fair finished channel or drain 30cm inner girth or part therein in cement concrete using extra cement including mitred/stopped ends, forms mould etc, complete.

Taking down chowkhats or frames not exc 1.5 sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutter of any description, n. exc. 1 Sqm each complete all as specified and directed.

Taking down shutter of any description exc. 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

S & F Powder coated any colour as approved aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F Powder coated any colour as approved aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required , with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. all as specified.

S&F Powder coated any colour as approved Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineering- charge.

S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed.

All as per item no 56 above but wire gauzed i.e. panel will be of wire gauze in lieu of single side prelam PVC sheet panel. The wire gauze shall be wapped on an additional square 8mm MS solid tube and this tube shall be welded of MS tube. The wire gauge shall be stretched to tighten firmily

S&F Factory made single extruded fully solid WPC (Wood Polymer Composite) solid door/ / Chowkhat of size 65X150 mm, double rebated, suitable for fixing flush shutter and fly proof shutter in the same frame, comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S & F 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F 4 mm thick Frosted plain glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified and directed.

Supply & fixing 75 mm stainless steel butt hinges (medium weight) cold rolled complete all as specified and directed.

Supply & fixing 100 mm stainless steel butt hinges (medium weight) cold rolled complete all as specified and directed.

S & F aluminium handles 125 mm long cast type, anodised complete all as specified and directed.

S & F aluminium handles 150 mm long cast type, anodised complete all as specified and directed.

S & F aluminium anodised barrel tower bolts 125 mm long of extruded section and fixed complete all as specified and directed.

S & F aluminium anodised barrel tower bolts 150 mm long of extruded section and fixed complete all as specified and directed.

S & F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed.

M & L floor door stopper of aluminium alloy body and tongue, anodized with rubber washer at bottom fixed with screw to body and fixed to door shutter, over all length of cover plate shall be 150 mm complete all as specified and directed.

Supply and fixing stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.4 mm complete all as specified and directed.

S & F mild steel work as in holdfast made out of flat iron any size including necessary welding or fixing nuts and bolts complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete.

M & L applying two coats of synthetic enamel paint on steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces complete.

M & L applying one coats of synthetic enamel paint on old steel surface of any description over 10 cm width or girth complete all as specified and directed.

M & L applying one coats of synthetic enamel paint on old painted surface wooden surfaces of any description over 10 cm width or girth complete all as specified and directed.

S &F framed work such as grills, grating etc with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barried iron doors ladders framed balusters, walk ways, railing framedwork of water tanks and similar work conforming to Fe.290 Gde E-165 complete all as specified and directed

Taking up/down plants, tree roots or vegetation growth wall upto roof level by means of cutting hole into brickwall and making good the surface of dismantled portion (not exc 150 Sqm cm superficial area and not exc one brick depth) using bricks bats / aggregate and plastering in cement mortar (1:4) to distributed portion and applying two coat of cement base paint to match the existing surfaces up to forth floor complete all as specified and directed by Engr in Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete all as specified and directed

S & F Vitreous China wash down water closet pan (Pedestal pattern), white (ETWC) with ‘P’ or ‘S’ trap, including connection to drain or outgoing pipe and including with 10 ltr capacity PVC flushing cistern, including brackets for flush tank, PVC connection 450mm long and 15mm dia to flushing cistern/ sanitary fittings with PTMT nuts of length 450mm and all necessary fittings, inlet, outlet pipe connections, and plastic water closet seat cover, closed pattern with recessed bottom cover and mild steel chromium plated hinge all as specified and directed.

S & F vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and directed.

Supply and fix, 10 ltrs capacity PVC valve less syphonic action type, low level flushing cistern, white with inlet, ball valve float and handle including brackets complete all as specified and directed.

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair 15 mm bore bib taps fancy type, chromium plated cast copper alloy, high pressure screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F stop valve fancy type suitable for 15 mm bore of pipe fancy type chromium plated ,high pressure with crutch or butterfly handle, screwed bith ends for for iron pipe or for unions ( concealed type) complete all as specified and directed

S & F 20 mm dia brass stop cock high pressure screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S & F 100 mm dia brass chromium plated over OH shower rose with arm and wall flange including fixing to steel pipe or union, complete all as specified and directed.

S&F CP angle stop valves (half turn type) conclead type (chromium plated fancy type) 15 mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handles, screwed both end for iron pipe or for unions complete all as specified and directed including taking down old one.

S & F PVC connection 15 mm dia 600 mm long with brass fly nut at both ends complete all as specified and directed.

S & F PVC 75 mm dia floor trap with grating including jointing with solvent cement complete all as specified and directed.

S & F stainless steel kitchen plate rack of size 31" x 24" x 10" made out of 1 mm thick stainless steel sheet complete all as specified and directed.

S & F stainless steel sink with drainage board, made out of 1.00 mm thick sheet with plug, washers, waste pipe, cast iron cantilever brackets, connecting union over all size 915 mm X 460 mm with bowl size 410 mm x 330mm x 160 mm complete all as specified and directed.

S&F Bib tap standard of PTMT any colour high pressure fancy type, with long body screwed for iron pipe and fixed. (Minimum weight 15mm-120gms) complete all as directed.

S &F PTMT grating 100 mm dia fixed with whote cement complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in any description and in any position not otherwise specifically provided for including cleaning the roof surfaces by brushing sweeping etc and removing rubbish material complete all as specified and directed.

M & L for rendering 10mm thick on fair faces of concrete surfaces in cement mortar 1: 4 under APP membrane finish rendering surfaces even and smooth with out using extra cement mixed with WPC @2% by weight of cement or as per manufacturer instruction. Complete all as specified and directed (Note:- WPC shall be measured and paid separately)

M&L for providing 25mm thick PCC (1:2:4) type 'B-0' (using 12.5mm graded crushed stone aggregate) after applying cement slurry @ 3 Kg/sqm, on top of roof, mixed with water proofing compound @ 200 ml per bag of cement, surface finished even and smooth without using extra cement including complete all as a specified and as directed.

M & L for cutting Grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 or cement concrete 1:2:4 type-B1 as required complete all as a specified and as directed..

M & L for brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as a specified and as directed.

M & L for for water proofing treatment on existing cleaned RCC roof with the following specification and manufacturing's instruction complete all as specified and as directed:- (a) Preparing and clening of fully dry surfaces as per IS3067-1966 (b) Applying bitumen primer conforming to IS:3384-1968 over the cleaned plaster surface @ 0.5 Ltr per sqm (c) Applying a layer of APP based polymeric membrance 3.0mm thick (minimum) weight 3.0Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160gms per sqm by torch application. The over laps shall be minimum 100mm on the transverse direction and 75 mm on longitudinal direction. (d) Applying one coat of aluminium paint @0.10 ltr per sqm over APP based polymeric membrane.

Excavation in trench not exceeding 1.5 M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

Excavation in trenches not exc 1.5 metre width and not exceeding 1.5 metre in depth in road/hardstanding and getting out complete all as specified and as directed.

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed.

Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete all as specified and as directed.

Cutting into existing manhole removing existing drain making good to wall and rendering cutting out branch channel and making good benching for 150mm dia pipe in cement concrete 1:2:4 complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) 150 mm set in cement mortar complete all as specified and directed.

Supply and laying 150 mm bore reinforced concrete pipe of Class NP-2, with collars, laid and jointed complete all as specified and as directed by the Engineer-in-Charge.

M/L for PCC (1:3:6) type C2 using 40mm graded broken stone aggregates for bed concrete to drain pipe packing under haunching for sides for 150 mm dia pipe lines complete all as specified and as directed.

S &F cast iron Grade FG 150 grating, railing, frame manhole cover fire and stoot doors, dompers, stop valve box and similar articles etc (weight exc 3 Kg each ) including frame different size fixed in concrete cover as directed by Engr in Charge.

M & L cutting chases for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth, complete all as specified and directed.

M & L for PVC (SWR) multi floor trap with grating including jointing with solvent cement, dia of outlet 75 mm in repairs all as specified and directed .

S&F in repairs 75mm bore PVC (SWR) waste pipes single socketed in any length with rubber ring joints laid in floors all as specified and directed.

S&F 110mm bore PVC (SWR) soil pipes single socketed in any length with rubber ring joints laid in floors all as specified and directed.

S&F 75mm bore PVC (SWR) waste pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F 110mm bore PVC (SWR) soil pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed by Engineer in Charge.

S&F 110mm bore PVC (SWR) junction single,(Single T) equal or unequal fixed to soil pipes all as specified and directed by Engineer in Charge.

S&F in repairs 75mm bore PVC (SWR) junction single, (Single T) equal or unequal fixed to waste pipes all as specified and directed by Engineer in Charge.

S&F in repairs 110mm bore PVC (SWR) bends any radius equal or unequal fixed to soil pipes all as specified and directed by Engineer in Charge.

S&F in repairs 75mm bore PVC (SWR) bends any radius equal or unequal fixed to waste pipes all as specified and directed by Engineer in Charge.

S&F 110mm bore PVC (SWR) vent cowl fixed to soil pipes all as specified and directed by Engineer in Charge.

S&F 75mm bore PVC (SWR) vent cowl fixed to waste pipes all as specified and directed by Engineer in Charge.

M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, laid in alternate bays, surface finished even and fair without using extra cement complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 (20 using mm graded crushed stone aggregate) as in coping, bed plates, hold fast blocks, bed block etc including providing necessary form work completed all as directed by Engr-in- charge.

S&F of 15mm dia bore steel water GI tubes medium grade with all fittings and fixed concealed to walls, ceilings or laid in floors complete with and including taking up or down 15mm bore steel water tubing and connections complete all as specified and directed

S&F of 20mm dia bore steel water GI tubes medium grade with all fittings and fixed concealed to walls, ceilings or laid in floors complete with and including taking up or down 20mm bore steel water tubing and connections complete all as specified and directed

S&F of 25mm dia bore steel water GI tubes medium grade with all fittings and fixed concealed to walls, ceilings or laid in floors complete with and including taking up or down 25mm bore steel water tubing and connections complete all as specified and directed

M&L for pre polished coloured chequered cement concrete tiles 30cmx30cmx 20mm thick made with electro vibro technology with rubber/ PVC moulded set, jointed and pointed in neat cement slurry in floors with white cement & pigment over laid screed bed or bedding layer of mortar 15mm thick(1:4) for laying floor finishes and including with dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed by Engineer in charge.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S&F s, Tubular towel rail (premium quality), 20mm dia, 600 mm long between flanges including brass chromium plated, complete all as specified and directed. (MAKE : JAQUAR, Cat No : ACN-111SM / PARRYWARE, Cat No : T6401A1 / ESS ESS, Cat No: AC-101 / CERA, Cat No: F5004103 / PRAYAG, Cat No: BA-20 / HINDWARE, Cat No: F840013 )

S&F Anodised aluminium Harrison rails (Curtain rod/drapery rod), 20mm dia, any colour, powder coated with and including fancy type bracket 2 Nos of each opening as approved and side stopper fancy type powder coated of required shape and size 2 Nos of each opening complete all as specified and directed.

Supply and fix vitrified tiles(light shade) of 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm as in floor set and jointed in neat cement slurry @ 3 kg per Sqm and pointed in coloured cement to match the shade of the tiles over and incl. 20mm screed bed in CM (1:6) complete all as directed.

Supply and fix vitrified tiles (light shade) of 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm as in skirting set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles over and incl. 10mm rendering in CM (1:3) complete all as directed.

M&L 40 mm thick P.C.C 1:2:4 type B1 using 20mm graded aggregate as in Sub-floor, sub base etc , finishing the surfaces of concrete ( without using extra cement) even and rough to receive the topping layer complete all as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

M&L for applying two coats of oil bound distemper on new surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) over a coat of alkali resistant primer applied over 3mm thick BIRLA/JK water proof wall care putty complete all as directed by Engr-in-charge. Complete all as specified and directed by Engineer -in-Charge.

Supply and fix vitreous china wash basin, white, counter top, size 450 x 400 mm oval shape excluding taps, waste, chain and plug and porcelain stopper complete all as specified and directed .

S&F in repair 15mm dia fancy type chromium plated basin mixer foam flow screwed for iron pipe incl taking down old all as directed by Engr-in-Charge. (MAKE : ESS ESS, Cat No : C-211A / JAQUAR, Cat No : CON-167KNB / PARRYWARE, Cat No: G1414A1 / CERA, Model: OCEAN / PRAYAG, Cat No: 9250 / HINDWARE, Model: CONTESSA PLUS) or equivalent make as specified in tender.

Supply and fix, as in repair, 15 mm bore bib taps, fancy type, chromium plated long neck cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified.

Supply & fix, as in repairs, brass chromium plated over head shower roses 125 mm size with or without swivel joint, including fixing to steel pipe or union all as specified and directed(Make : CERA, Cat No: F7040103 (for arm) & F7020305 (for shower) / PARRYWARE, Cat No: T9802A1 (for arm) & T9986A1 (for shower)/ESS ESS, Cat No: OH-104A / HINDWARE, cat No: F160051) or equivalent make as specified in tender.

S&F in repairs 15mm dia soap dish, square, acrylic body with chromium plated base complete all as specified and directed. (Make : Jaquar, Cat No : AKP-35731P / PARRYWARE, Cat No: T6403A1 / ESS ESS, Cat No: AC-103 / PRAYAG, Cat No: BA-35 or equivalent model in CERA /HINDWARE) or equivalent make as specified in tender.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long as in repair complete all as specified and as directed. Make : Ess Ess, Cat No AC207 or equivalent make as specified in tender.

S&F in repair CP bottle trap with internal portion 32mm size with 190mm long wall connection pipe complete all as specified and directed (Make: JAQUAR, Cat No: ALD-769L250x190 / ESS ESS, Cat No: C-231C / HINDWARE, Cat No: F850003 / CERA, Cat No: F8060302/ PRAYAG, Cat No: BEA-26) or equivalent make as specified in tender.

Supply and fix in repairs Low density polyethylene pipe connection, comprising of 15 mm dia 600 mm long having PTMT union at each end of connection to each of pillar tap/cistern/stop cock/urinal etc. at one end, stop cock at other end complete all as specified and directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON or equivalent make as specified in tender.

(E/M Portion) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants , regulators, sockets etc excluding light fitting for taking credit removing from site and making good disturbed surface of walls, floors etc complete all as specified and as directed.

Materials and Labour for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting modular type switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage) (a) One light point or one fan point controlled by one switch.

All as per item No 146 but one 3/5 pin socket outlet, 5 Amp independent

All as per item No 146 but one 3/5 pin socket outlet, 5 Amp on the same board with other switches

All as per item 146 above but using 2.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core for line conductor and 1.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core for earth continuity wire for one 15/16 amp multi socket out let independent. (concealed wiring) (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches.

S & F Modular Switch 1 way 6 A, 1 module complete all as specified and as directed.

S & F Modular Switch 1 way 16 A, 1 module complete all as specified and as directed.

S & F Modular Socket 6 A, 2/3 pin combined 2 module complete all as specified and as directed.

S & F Modular Socket 6 A/ 16 A, 2/3 pin combined 2 module complete all as specified and as directed.

S & F Modular Fan step regulator, 120 watt, 2 module complete all as specified and as directed.

S & F Modular Bell push 6A, 1 module complete all as specified and as directed.

S & F Modular Blank plate, 1 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 1 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 2 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 3 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 4 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 6 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 8 module complete all as specified and as directed.

S & F Modular type White cover plate with frame 12 module complete all as specified and as directed.

S & F Modular type Metal Flush box 1/2 module complete all as specified and as directed.

S & F Modular type Metal Flush box 3 module complete all as specified and as directed.

S & F Modular type Metal Flush box 4 module complete all as specified and as directed.

S & F Modular type Metal Flush box 6 module complete all as specified and as directed.

S & F Modular type Metal Flush box 8 module complete all as specified and as directed.

S & F Modular type Metal Flush box 12 module complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V,W/NW light AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Taking down of old Submain wiring upto 10 sqmm any type including batten/ conduit/ casing at any indicated situation complete all as specified and as directed.

M & L for sub main wiring with 4 run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm along with one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm as earth continuity conductor drawn through and including PVC casing-capping of suitable size, surface type all as directed.

All as per Srl. Item No. 172 above but with 2 run of 6.0 Sqmm cable and 6.0 Sqmm as earth continuity conductor.

All as per Srl. Item No.172 above but with 2 run of 4.0 Sqmm cable and 4.0 Sqmm as earth continuity conductor.

Cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed.

Taking down of Old MCB DB any type any size including MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site.

S&F LED Bldg Security Light fitting 30W and bracket all accessories with pressure die cast housing toughened glass and individual LEDs with secondary optics and IP 66 protection as in repair complete all as specified and directed.

S & F TP&N Vertical Loadline Dbs are fitted with Bus Bars, Neutral Links, Blanking Plates 4 way double door DB LL 4W DD VERT W/O MCCB. complete all as specified and directed.

Supply and fix MCCBs 415V, breaking capacity 16KA, 4 Pole rating 100 Amps. Complete all as specified and directed.

S & F Sheet metal enclosure for MCB DB double door single pole & Neutral 4 way with 200 amps rated bus bar complete all as specified and directed.

S & F Double door sheet metal enclosure for DBs(Premium range) for mounting of MCB for 240 Volts 8 Way with 100 Amps rated copper bus bar, single pole and Neutral complete all as specified and directed.

S & F Double door sheet metal enclosure for DBs(Normal range) for mounting of MCB for 240 Volts 8 Way with 100 Amps rated copper bus bar, single pole and Neutral complete all as specified and directed.

S&F GI in repair tubing medium grade of size 15 mm dia incl painting and making hole for extension of fan hook in high roof ceiling complete all as specified.

S & F in repair clamp with buckle for hanging ceiling fan including nut and bolts complete set all as specified and directed.

Supply only MCB, 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed.

Supply only MCB, 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed.

Supply only MCB, 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed.

S & F in repair AC short circuit protection motor starter 25 Amps capacity AC 230 Volt complete all as specified and directed.

S & F in repair lamp pendant / batten holder, complete all as specified and directed.

S & F exhaust fan 300 mm sweep, heavy duty, 1400 RPM , AC single Phase 230 / 240 volts, metal body with louver shutters and connecting up with and including twin core twisted flexible copper conductor cable of suitable dia ,nut bolt and accessories, BEE 5 Star Rated and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 sqmm , 3 core, 1100 Volts grade, from ceiling rose / connector to fan complete all as specified and directed.

Supply, Laying and testing for replacement of 50 sqmm 3.5 Core XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured electric power cable 1100 Volts grade with stranded aluminium conductor cable, laid in trench or fixed to wall with saddles/Flat iron clamps as per site requirement /passing through pipe/pole complete of the following sizes and cross sectional area :- Note :- Necessary earth work to be measured and paid separately.

S & F BLDC ceiling fans complete with all accessories 230 volt single phase 1200mm sweep with down rod any size , canopy, fan blades and accessories, BEE 5 Star Rated and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 sqmm , 3 core, 1100 Volts grade, from ceiling rose / connector to fan complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.0mm GI wire (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no 5 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering all as specified and directed and tested on completion.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

DEEPAK KHATTAR (BID ID -3263033)

GAYATRI ENTERPRISE (BID ID -3262226)

DUTTA & DUTTA (BID ID -3262040)

SK CONSTRUCTION SYNDICATE & ENGG CO (BID ID -3259938)

RAJ ENTERPRISE (BID ID -3260666)

UNITED ENGINEERS (BID ID -3259919)

MS AP CONSTRUTION AND CO (BID ID -3260827)