752986A PROVN OF SINGLE MEN BARRACKS INCLUDING COOK HOUSE IN EPC MODE FOR AGNIVEERS AT 1 STC JABALPUR

PCC chamber 1:4:8, type C-1 using 20mm graded stone aggregate, internal surface of concrete chamber shall be given 12mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge ( 0.63) 8 mesh per linear inch, 50mm thick cover of RCC 1:2:4, type B-1, using 20mm graded stone aggregate reinforced with 8mm TMT bar at 100mm center to center both ways and charcoal dust and common salt all as shown in electrical plate No.3 of MES SSR Part-I and as specified including excavation and earth work and connecting the earthing to an earthing test point as specified and testing on completion all as directed. Note:- Unit rate quoted is inclusive of earth lead and protection pipe upto 7.5 metre from earth plate.

The design of integral aco

ustic enclosure should be any type approved by national Physical laboratory as per Central Pollution Control Board (CPCB-IV + Emmission compliant) latest norms/regulation Noise level 75dB(A) at a distance of one meter with fuel tank, battery and standard accessories as recommended by manufacturer, vibration pad, sand cushioning around PCC foundation, tools and spares, as provided by manufacturer all as specified and as directed with the following specifications of :-

M&L for Precast Reinforced Cement Concrete(RCC) 1:4:8 type D2 using 40 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and minimum reinforcement as per relevant IS code and set in CM 1:6 complete all as specified and directed. (Note : Reinforcement shall be measured and paid for separately.)

Item No 1 (A): Designing (Structurally & Aesthetically) and construction of block of Single Men Barracks For Agniveers with precast construction technology (2D) permanent specification for (G+3) Storey RCC Framed Structure all as per design basis report, detailed in scope of work and other documents of the tender complete all specified and directed.

SCHEDULE "A" Part-I (Building/Structures) (To be quoted by the Contractor) Building Works mentioned at item no 1(A), Item No 1(B) & Item No 1(C) is in ENGINEERING PROCUREMENT CONSTRUCTION (EPC) Mode. Contractors has to carry out the detailed engineering design of these buildings, procure all the equipments and materials necessary and then construct to deliver a fully functional facility to the MES department.

Sch 'A' Part-II (External Electric Supply) Lump sum price worked out by the contractor for (External Electric Supply) as listed in Schedule 'A' Part-II against the lump sum price inserted by the MES.

Sch 'A' Part-III (External Water supply) Lump sum price worked out by the contractor for (External Water supply) as listed in Schedule 'A' Part-III against the lump sum price inserted by the MES.

(Sewage Disposal)

Schedule 'A' Part II

Item No 59 : Chair Easy FD-229

M&L for GI tube light grade with all fitting laid in trenches of fixed to pole of size:-

Schedule 'A' Part IX

Schedule 'A' Part X

Sch 'A' Part-VII (Security Fencing & Gate) Lump sum price worked out by the contractor for (Security Fencing & Gate) as listed in Schedule 'A' Part-VII against the lump sum price inserted by the MES.

Study Room

Cook House & Dining Hall

Common Room

Furniture

Item No 02 : Supply, installation, testing and commissioning of copper wound (double wound), step down transformer of capacity 160 KVA (Level-1), plinth/ floor mounted, OUT DOOR TYPE and conforming to IS 1180:2014, AC 3 phase 50 Hz, ONAN with external cooling tubes/ radiators, having no load voltage ratio 11/0.433 KV corresponding to principal tapping, delta connected primary side (11KV HV side) and star connected on secondery side (433V LV side) in accordence with vector symbol Dyn-11 (Vector Group), manual type off load tap changing facility on HT side to vary secondary voltage from minus 7.5% to plus 7.5% in steps of 2.5%, continuous rating of capacity 160 KVA including bushing on HT end & cable box on LT side. The transformer shall be complete with all standard fittings and accessories, gauges, first fill of tranformer oil as per IS-335, ISI marked duly filtered & dehydrated etc.

Item No 03 : M& L for cable root indicator MS sheet embossed with LT 1100 Volts Volts UG made with CI Plate 6 mm thick fixed with MS angle Iron of size 30x30x4mm of length 400 mm long including PCC work 1:2:4 type B1 of size 150x150x150 mm complete all as specified & directed

Item No 04 : M& L for cable root indicator MS sheet embossed with HT 11000 Volts UG made with CI Plate 6 mm thick fixed with MS angle Iron of size 30x30x4mm of length 400 mm long including PCC work 1:2:4 type B1 of size 150x150x150 mm complete all as specified & directed

Item No 05 : Supply, installing, testing and commissioning out door type LT Panel of suitable size, Floor mounted, CPRI approved factory made totally enclosed, dust and vermin proof, shutter in front and in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both front and rear door with 4 side slanting roof duly projected and painted to both internal and external surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and including following accessories and mounted on PCC Plat form made out of PCC 1:3:6, 100 mm thick, 1 Mtr all round the panel board complete with the following items housed in : -

Item No 06 : S & F Integral decorative LED bollard with IP 65/66 protection suitable for 10 watts LED with necessary elecrical connections with adequate size of Nuts and Bolts including junction box with 6-32 A MCB of size complete as all specified and as directed.

cluding galvanised iron earth strip 32x 6 mm by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : -

Item No 08 : Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth strip 25 X 4 mm by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Item No 09 : S&F earth continuity conductor or main earth lead of 32 X 6 mm GI strip with saddles and fixing screw etc for roof conductor and down conductor fixed to wall on batten or recess or ground for connecting earthing to various equipments as required complete all as directed.

Sch 'A' Part-VIII (Summer & cooling Applinces) Lump sum price worked out by the contractor for (Summer & cooling Applinces) as listed in Schedule 'A' Part-VIII against the lump sum price inserted by the MES.

Sch 'A' Part-X (Fire Fighting System) Lump sum price worked out by the contractor for (Fire Fighting System) as listed in Schedule 'A' Part-X against the lump sum price inserted by the MES.

Sch 'A' Part-XI (Lightning Protection System) Lump sum price worked out by the contractor for (Lightning Protection System) as listed in Schedule 'A' Part-XI against the lump sum price inserted by the MES.

Sch 'A' Part-XII (Site Clearance) Lump sum price worked out by the contractor for (Site Clearance) as listed in Schedule 'A' Part-XII against the lump sum price inserted by the MES.

Schedule 'A' Part-XIII (Miscellaneous items of works)

Note for Srl No 2 to 17 The percentage above / below the SSR -2020 (part-II) rates shall be derived from the amount quoted by the contractor against Srl No. 2 to 17 by comparing it with the amount inserted / pre- priced by the department and the same shall be applicable for the items of respective schedule

Item No 15 : Earthing complete for various equipments with galvanised steel earth plate electrode 600 x 600x 6mm thick directly burried in the ground (earth pit not less than 2.25 metre deep below ground level) with top edge of earth plate not less than 1.5 m below the ground level, connected to G.I Strip 32 x 6 mm by means of bolts, nuts, chuck nuts and washers of galvanised iron or steel, GI pipe 40mm bore light grade for protection of earthing strip,

Item No 16 : S & F earth continuity conductor for main earthing lead 32 X 6 mm strip burried in ground or fix in walls with bolts all as specified and directed by engineer in charge.

Item No 17 : Supply and fixing of ducted cooler top/down discharge - 03 Nos/Floor nominal air delivery of 25000 CMH ,1.5 KW Motor power,cooling capacity upto 1600 sq ft UV Stablized High Grade Plastic of Tank capacity 70 litres Fan Dia 620 mm with Honeycomb pads of thickness 100 mm with 80 % minimum cooling efficiency,with 3 phase starter ,hanger hook and L shaped bracket including supply ,Installation ,commissioning and balancing of site fabricated Galvanised Sheet Steel (GSS) ducts conforming to IS: 277. Duct with 1:3 Ratio of 22G 0.7 mm and 24G 0.6 mm sheet from machine to ceiling height and ceiling to the alumium grills should rectangular shape ducting complete with neoprene rubber gaskets,nitrile rubber acoustic insulation of size 19 mm (inside) ,thermal insulation of size 6 mm (outside ),elbows,splitter damper vanes,hangars,supports.Duct work shall be rigid and straight without kinks.All exposed ducts within the conditioned space shall have slip joints.

Item No 18 : Supply, installing, testing and commissioning out door type LT Panel of suitable size, Floor mounted, CPRI approved factory made totally enclosed, dust and vermin proof, shutter in front and in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both front and rear door with 4 side slanting roof duly projected and painted to both internal and external surfaces with powder coating paint in heat process of sheet and suitable for 500 volt

Preparation of two coats of synthetic enamel paint on new steel surfaces of any description, over 10cm in width or girth,not otherwise described including preparation over a coat of red oxide Zinc chrome prime complete all as specified and directed complete all as specified and directed.

s, 50 Hz, 3 phase 4 wire system and comprising with and including following accessories and mounted on PCC Plat form made out of PCC 1:3:6, 100 mm thick, 1 Mtr all round the panel board complete with the following items housed in : -

Arboliculture

Item No 19 : Supply, installation, commissioning Auto Clean Kitchen Chimney, Baffle Filters, Touch Control with Motion Sensor 60/90cm 1200 m3/h - Silver (6078 MS AC) and all as specified and directed.

Item No 20 : Supply, installation, commissioning refrigerator, electric driven (single phase), capacity more than 195 Litres upto to 310 Litres.BEE 5 star rated all as specified and directed.

Item No 21 : Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA all as specified and directed.

Supply and fix Valves, Sluice, flanged of class 1.6 PN,100 mm dia and all as directed.

Item No 22 : Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 1 KVA all as specified and directed.

Item No 23 : S&F Concertina Coil of 600 mm dia of Approved Type/Make for laying on Y shape angle fixed on boundry wall etc complete.

Item No 24 : Plantation of tree of fruits/Herbal nature and taking care for three year after complition of work including watering providing manure/fertilizer etc complete all as directed.

Item No 07 : Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and in

Item No 25 : M & L for composite rain water harvesting system of 5000 litre capacity include of the following (i) under ground water storage tank of 5000 litre capacity 01 No (ii) First flush system 01 No (iii) Gravity Filter 01 No (iv) Delivery pipe 25 mm size UPVC (SCH- 40) 15 RM (v) Down take pipe 100 mm size UPVC (SCH- 40) 15 Rm

automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system without hand set (04 Nos, one each in car, Machine room & near ground floor landing door) & human interface device all other finishes standard safety features should be as per IS specification and modern practices in market in lift complete all as specified below:-

Item No 26 : Supplying and laying and jointing for (SN 8) DWCPE 180mm (OD)/ 163 (ID) conforning to IS-16098:2013 part -I with and incl jointing materials complete

External Water supply

Item No 27 : M&L RCC Septic tank conventional type designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab, Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for 100 users.

Item No 28 : M&L Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 3.0 M x 3.0 M depth complete

Item No 29 : Supply and lay pipe ductile Iron , S/S including specials, Class “K-7” ,100 mm (4”) dia and all as directed.

(f) Internal roof supports should be of FRP/GRP 5 mm thick hollow square section. (g) Air-vent dia 100mm with mosquito proof mesh insect proof.. (j) Aluminum body water level indicator with clear tube type and brass nozzle (For Tank height more than 1 Meter) Internal FRP ladder with wall mounting arrangement inside (For Tank height more than 1 Meter). (h) External GI ladder with complete fixing arrangement outside. (J) Complete fixing of Inlet/Outlet/overflow/drain with suitable colour coding paint should be GI Flange type with 9" long Nipple and pipe of uitable sizes. (k) Panel Thickness 6 mm -10mm. (l) Neccesary Civil foundation and Base Frame. (m))Brick work required with plaster . (n) Frame work of I section and C channel.

Item No 30 : M&L for tapping in existing DI pipe lines 150 mm dia and inserting tee of 150x 100 mm and all as directed.

Item No 31 : Construction of brick masonry valve pit of size 1200 mm x 1200mm x 900 mm (internal dimensions) with one brick thick wall in cement mortar 1 : 4 on 100 mm thick PCC 1:4:8 type D2 (using 40mm graded broken stone aggregate) as in foundation lean concrete, including PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in benching and coping and 10mm thick cement plaster in CM (1:4) internally and externally upto 15cm below ground level providing valve pit cover 40x40x6mm angle iron frame all-round fixed by means of 4 Nos holdfast 150mm long made out of flat iron 40x6mm embedded in PCC block (1:2:4) type B-1

Item No 32 : Supply, installation, testing and commissioning LT , 415 Volt, 4 wire AC 50 Hz, cubical panel (Feeder Pillar Box) factory made, out door, pedestral type, feeder pillar box, hutted roof, weather & vermin proof fabricated of 3.0mm thick MS black sheet, front & back double shutter opening type, spray two earth terminal suitable cable glands for all incoming and outgoing cable including grounting of feeder pillar box 60cm above ground level by providing 90 cm long angle iron of size 50 x 50 x 6mm welded on all the fours corners, embedded in PCC 1:2:4 using 20mm stone aggregate upto 30 cm, complete all as specified and directed by Engr-in-Charge including the following accessories /components. (a) Aluminium bus bar - 200 amps rating - 03 Nos. ( for phases and 100 Amps for neutral 01 No insulated with proper colour coding phase wise ). Qty -04 (b) Incoming MCCB 4 pole 100 Amp, 415 volt, 16 KA Thermal setting 70% to 100% - 01 No (Incoming) (Qty 02 no.) (c) Outgoing

Item No 33 : M&L for fabrication, transportation, erection & testing for Hot compressed molded SMC (sheet molding compound) panel tanks of 12000 gallon capacity , erected at ground level using steel structure of of Brand SINTEX, AMITEX, DEVI POLYMERS as per BIS: 14399 Part-I & Part-II. ISI Marked SMC Panel tanks of approved brands. Roof & Base of SMC Panel tanks having panels of size 1.00 m x 1.00 m, 1.00 m x 0.5 m . Side Walls of tanks shall be constructed using SMC panels of size 1.00 m x 1.00 m panel as per site requirement or as per OEM standards. One manhole of diameter 600mm lockable lid of hot pressed moulded made out of SMC should be provided on the roof of tank with lockable lid and aluminium ladder above 1mtr height inside & outside the tank for access. Tanks must have vertical iron posts lied firmly with Tie rods.

Item No 34 : Supply and fix pressure sensor switch having ambient operating tem -40 to 65 degree celcius , differential pressure range 0.7 bar to 4 bar , regulation range 0.2 bar to 7.5 bar ISO STANDADARD 228-1 complete all as specified and as directed.

Item No 35 : Supply , Install, testing & commissioning of monoblock pumpset, 3 phase, 415 V, 50 Hz, bronze impeller,discharge 27-15 lps @ 12-24 mtr head complete all as specified and as directed.

M&L for painting over steel/ iron Surfaces of any description, ove

Item No 36 : Supply and fix pressure sensor switch universal type having ambient operating tem -40 to 65 degree celcius , differential pressure range 0.7 bar to 4 bar , regulation range 0.2 bar to 7.5 bar ISO STANDADARD 228-1 complete all as specified and as directed.

Item No 37 : Supply and fix automatic air release valve 50mm dia suitable for domestic water with 50 mm gun metal stop valve complete.

Returning filling in including spreading levlling ,watering and well ramming in layers nexc 25cm thick complete all as specified and directed.

Item No 38 : Supply only of fire extinguiser ISI marked CO2 type Fire Extinguisher 4.5 KG capacity conforming to IS : 15683 :2006 (old IS : 2878) made from seamless cylinder conforming to IS : 7285 duly approved by chief controller of explosive , Nagpur fitted with ISI Marked Controlled valve conforming to IS : 3224 , high pressure 1 mtr long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting bracket, , suitable for operating between 30 degree centrigrade to + 55 degree centigrate, Fire Rating Class - 138.

Removing excavated material to a distance exc 500m but n exc 1.5km, depositing where directed at a level n exc 1.5 M above the starting point.

Item No 39 : Supply only of stored pressure fire extinguiser ISI

M & L for Grubbi

ng up tree trunk (exc 30 cm but n exc 100 cm) including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site

M & L for Grubbing up tree trunk (exc 100 cm but n exc 150 cm) including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site

Electric Lift

marked powder type Fire Extinguisher 4 KG capacity suitable for Class "A", "B", "C" Fire consisting with discharge hose and nozzle of welded cylinder, squeeze lever discharge valve fitted with pressure indicating guage, internal discharge tube, discharge nozzle suspension bracket conforming to IS : 15683 :2006 (old IS : 2878) duly charged with ISI Marked Mono Ammoniumphosphate base ABC powder conforming to IS : 14609 and pressurized with Nitrogen Gas, suitable for operating between 30 degree centrigrade to + 55 degree centigrate, Fire Rating Class - 1A & 13B

Sch 'A' Part-VI (Area Drainage) Lump sum price worked out by the contractor for (Area Drainage) as listed in Schedule 'A' Part-VI against the lump sum price inserted by the MES.

Item No 40 : Supply only of 03x Fire bucket iron body red colour 10 L capacity for dry sand stored type including mounding stand paitnted with red colour ISI Marked IS : 2546 :2006, complete all as specified and as directed.

Item No 41 : Supply , hoisting and fixing pvc three layer water storage tank of capacity 5000 ltr including all fitting arrangement complete all as specified and as directed.(Note: For SM Barrack 1x 5000 ltrs )

Item No 42 : Supply only of Fire Extinguisher Mechanical Foam type ISI Marked Foam (AFFF) type Fire Extinguisher 9 ltrs capacity fitted with Forged Brass squeeze lever discharge valve, conforming to IS : 15683 :2006, complete with initial refill consisting of ISI Marked CO gas cartridge of 60 gms capacity conforming to IS 4947 and ISI Marked AFFF conforming to IS : 4989, suitable for operating between + 50 degree centrigrade , Fire Rating Class - 3A & 34B

Sch 'A' Part-V (Sewage Disposal) Lump sum price worked out by the contractor for (Sewage Disposal) as listed in Schedule 'A' Part-V against the lump sum price inserted by the MES.

Item No 43 : S&F porceliene insulators 15 BMD type T with nut bolts / screws for fixing of aluminium strips on roof including provn of PCC of size 10cmX10cmX10cm height etc to avoid leakage of roof complete as directed.

Item No 44 : Earthing complete with galvanised steel earth plate 60×60cm ×3.15mm thick electrode earthing lead buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised iron strip 32×6mm by means of bolts, nuts, check nuts & washers etc made of GI and connected to earthing test point all as shown in electrical plate No. 5 of SSR Part I of 2009 & as specified or indicated and testing on completion including excation/earth work in any type of strata PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm), cast iron frame, funnel with wire mesh,GI watering pipe of 20 mm bore medium grade and lugs, with and including galvanised iron strip 32×6mm with GI protection pipe of 15 mm medium grade 7.5 meter long, etc complete all as specified.

Schedule 'A' Part VIII

Item No 45 : S&F Traffic convex minor of size 800 mm dia unbreakable having clear and definite mirror image with upper class collar provided with suitable clamps & nut bolts. The complete set shall be fixed on MS pipe 65mm NB 2.0 meter long from Ground level duly powder coted/painted white/blue color etc complete all as specified and directed.

Item No 46 : Design supply, install testing & commissioning passengers liftof capacity 8 passanger (544 Kg,) speed 1.5 metre/sec, lift with single speed motor 415 volts, 3 phase, AC 50 Hz supply conforming to IS14665, suitable to serve G + 03 upper floors with AC variable voltage & variable frequency drive (VVVF drave) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism), sliding staninless steel doors, car size-as per IS and suitable to install in install in lift well, door size- as per IS or manufacture specification,

Sch 'A' Part-IV (Road Path Culvert) Lump sum price worked out by the contractor for (Road Path Culvert) as listed in Schedule 'A' Part-IV against the lump sum price inserted by the MES.

Item No 47 : S&F for galvanised iron strip of size 25 mm x 4 mm for earth contunity conductor complete all as specified and directed.

Item No 48 : Locker Steel FD-1029/257

Item No 49 : FD-1029/257 FD-280

Item No 50 : Bed Hard FD/E6/MAP/08®

Item No 51 : Chair Writing FD-280

Item No 52 : Table 60x60 cms FD-293

Item No 53 : Chair Writing FD-280

Item No 54 : Table 90x60cm with Drawers FD-283/224

Item No 55 : Notice Board FD-99R

Item No 56 : Chair Dining FD-279

Item No 57 : Receptacle FD/E6/Map/13

Item No 10 : S&F earth continuity conductor or main earth lead of 25 X 3.15 mm aluminium strip with saddles and fixing screw etc for roof conductor and down conductor fixed to wall on batten or recess or ground for connecting earthing to various equipments as required complete all as directed.

(External Electric Supply)

Base frame arrangements . The engine and alternator would be coupled by means of specially diesigned flexible coupling and both the units including the radiator would be mounted on a rigid fabricated base to form a compact arrangement. The steel shall be Tisco / SAIL or equivalent make.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes,1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor conforming to IS 7908 / (PART-I) 1988 with the latest amendments including jointing materials such as cable glands & lugs etc and testing on completion all as directed etc of the under mentioned type and sizes :-

(a) 3.5 core x 120 sqmm

(b) 2 core x 6 sqmm (Garden lighting & Post top Lantern)

(c) 4 Core X 25 Sqmm (Centralised Cooler)

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes,etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

M/L for Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

M/L for Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

Supply and laying sand cushioning with dry and clean washed sand over and under the under ground cable in trenches, ducts for cable protection 150 mm below & 80 mm above the cable as protection of cable complete as specified & directed. Note : Punned thickness of sand shall be measured & paid.

Supplying and laying reinforced precast concrete cable cover, class LV Type 2 flat, size 300mm x 180mm x 40mm complete all as specified and directed by Engr in charge.

Supplying and laying reinforced precast concrete cable cover, class HV Type I, flat, size 300mm x 180mm x 40mm complete all as specified and directed by Engr in charge.

Supply and erecting steel tubular swaged poles complete with cast iron base plate, finial taper plug , bolts, nuts & screws complete all as specified, type 410 SP - 55 of 11 mtr long including painting of pole with one coat red oxide primer & two coat of aluminum paint & embedded portion of pole shall be painted with two coat of black paint complete all as specified and as directed.

M&L for cross arms, bracing, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminum paint complete all as specified and dircted.

Item No 11 : Supply and fix junction box made out of polycarbonate with IP 55/IP 65 protection of size 155 x 210 x 92 mm,having terminals for termination of cable with necessary nuts and bolts, including -02 Nos polycarbonate cable gland, 01 Nos DIN rail for mounting of MCB and 01 No, MCB SP, 10 KA, 6 Amps in and including fixing clamp of FI 50 x 6mm with necessary nuts and bolts complete all as directed.

(a) 50 mm Medium Grade

(b) 80 mm Medium Grade

M&L for PCC (1:2:4) type B2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and pilasters, buttresses columns, posts etc complete all as specified & directed.

Sound acoustic enclosure : CPCB approved sound acoustic enclosure sutable for above genrator set with complete set installed within canopy.

M&L for 40 to 80mm graded broken stone aggregate for spreading/ loose filling in the substation or other places where directed including stacking materials in regular heap/ stack for measurement complete all as specified and directed.

S&F for lightning arrestor Expulsion type complete with all fittings, transmision/ distribution class , current rating 65 kA suitable for 11 KV system, discharge capacity 65 kilo amps and mounting on poles including all necessary bolts, nuts and washers and making electric connection and testing on completion complete all as specified and directed. Make:- SCHNENIDER or BHEL or GE POWER or W/S INSULATORS or SOUTHERN INSULATORS or OBLUM as approved by GE.

Supply and fixing of switch air break gang operated triple pole mechanically operated horizontal type out door with all other fittings/ accessories mounted on & including porcelain insulators and steel frame with operating mechanism worked from ground level with & including operating rod of 32mm dia GI pipe medium grade (ISI marked) with MS handle with locking arrangement, for current rating up to 400 Amp 11000 Volts including dropout fuse set 15 insulators to suit gang operated triple pole 11 KV switch, connecting, commissioning and testing on completion complete all as specified and directed.

M & L for Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for HT, 25 x 20 cm size complete all as specified and directed.

Supply, fix for LED post top lantern 40 watt light fitting made of cast aluminium spigot housing with decorative opal acrylic diffuser with IP 65 protection complete with all accessories fixed on GI pipe 50 mm dia complete all as specified and directed.

Supply and fixing LED Solar street light fitting 36 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor with all connected accessories like nuts bolts clamps etc complete all as directed.

Supply and fixing HT 11 KV (Earthed) grade heat shrinkable end termination jointing kit outdoor type complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 -185 sqmm complete all as specified and as directed.

Materials and labour for Aluminum conductor steel reinforced (ACSR) conductor as in LT overhead electric line and stretching the same with required span, standard sag and binding the conductor with pin/shackle insulator and jumpers with aluminum binding wire not less than 2.00mm dia, PG clamp etc complete all as specified and as directed.

Supply and fixing Pin type insulator, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150mm height, 150mm dia for 11000 volts grade confirming to IS-2486 complete all as specified and as directed.

Material and labour for anti-climbing device, spike type fabricated from structural steel comprising of MS flat 20mmx6mm, MS round bar pointed, 8mm dia, 20cm length welded on MS flat fixed with nuts, bolts, washers and welding with and including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

S & F drop out fuse unit explusion type for out door air break gang oprated switch single pole mounted on and including two numbers insulators for 11 KV working pressure fixed to MS channel with nuts, bolts and washer etc and current carry capacity above 50 Amp upto and 100 Amp complete all as specified and as directed.

Supply only chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wire, any mesh, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wires complete all as specified and as directed.

Supply and fixing mild steel Fe 410-W (Gde-E- 250) quality-A, framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Supply and fixing mild steel Fe 410-W (Gde-E- 250) quality-A, plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and as directed .

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part III

(External Water supply)

M&L for cement concrete type B2 , 1:2:4 using 40 mm gradded stone aggregate in surface channels and drains complete

Supply and lay pipe galvanized, “Medium class”, including fittings of dia 50 mm and all as directed.

Supply and lay pipe galvanized, “Medium class”, including fittings of dia 40 mm and all as directed.

Supply and lay pipe galvanized, “Medium class”, including fittings of dia 25 mm and all as directed.

Supply and lay pipe galvanized, “Medium class”, including fittings of dia 20 mm and all as directed.

S&F gun metal gate valve of following sizes screwed down high pressure with handle, Iron wheel (ISI marked) complete all as directed.

(a) 50mm bore

(b) 25mm bore

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes,etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

M/L for Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

M/L for Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part IV

Supply and fix air termination rod single pointed aluminium rod length 12 mm dia & 300 mm long .

M&L for 100 mm thick PCC 1:2:4 TYPE B1 using 20mm graded stone aggregate as in floor.

Supply and errect vertically Galvanised, medium grade pipe 20 mm diameter complete with fittings for raising height for air termination rods all as specified and directed.

(Road Path Culvert)

Excavating over areas, n exc 1.5 m deep and getting out soft/loose Soil

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil

Add to (or deduct from) last item for every 3 cm or part thereof above or below 15 cm average depth in soft /loose soil

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M&L for soling (sub base) with broken boulders or quarried stones 200 mm thick spread interstices filled surface formed rolled and consolidated to required gradient and camber all as spfd.

M & L for Laying and compacting 150 mm thick (compacted thickness) WMM laid in two layers of 75 mm each Wet Mix Macadam (WMM) grading as pe table 400-13 of MoRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with wate to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-1 OOKN static weight and consolidating to required gradien and camber complete all as specified and directed The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 complete all as specified.

Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate of application of 0. 2 - 0.30 kg/sqm on surface of bitumen including preparation of bitumen surfaces as specified in Table 500-5 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete including preparation of bitumen surfaces all as specified and directed .

M&L premixed bituminous macadam laid/rolled and compacted to required gradient and camber with using 20 mm graded stone agg and paving bitumen 4% by the weight of total mix (consolidate thickness 75 mm or less as required ) complete all as specified and as directed.

Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate of application of 0. 7-1 kg/sqm on surface of WMM/WBM including preparation of WBM/WMM surfaces as specified in Table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete including preparation of WBM/WMM surfaces all as specified and directed .

M & L for laying bituminous premix asphaltic semi dense concrete VG-30 avaraging 40mm consolidated thickness with 5.5% binder content by weight of total mix using asphalt mechanical mixer plant & consolidated with 8to 10 ton power road roller to reqd level gradient camber and super elevation.

Continuous edging with roughly squared sand stones of size 30 cm x 5 cm (30cm deep & 5 cm thickness), length of each patti not less than 60 cm Complete of using sand stone/Katni sone all as specified and directed.

M&L preparation of road surface and applying thermoplastic relflective paint in white or any tint marking of min 2 mm thick single coat as in center line and edge line road marking of 150/100 mm width using ''HOT MARK" thermoplastic modern propelled road marking machine as directed incl all ingredients such as blinder, glass beads, Titaniumdioxide calcium carabonate inter fillers thermroplastic requirement for glass beads shell be the Table No 650.4 of MOT specifications incl spraying of glass beads etc all as per manufactures instrustions and as directed

Cement concrete type D-2 1:4:8 (using 20 mm graded aggregate) as in foundation filling and mass concrete , sub base complete all as directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & attern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone agg) as in seismic and other similar bands, coping, bed block or similar work including necessary form work complete all as specified.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Supply and fixing in repair cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions.

Supply and fixing in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. all as specified and directed

S&F 600 mm bore Reinforced concrete pipes class NP3, laid and jointed complete with collars complete all as specified and directed.

M&L PCC 1:3:6 type C2, 40mm graded agg as in concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 600 mm bore complete all as specified and directed.

S&F 450 mm bore Reinforced concrete pipes class NP3, laid and jointed complete with collars complete all as specified and directed.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part V

Item No 1 (B): Designing (Structurally & Aesthetically) and construction of block of Dining Hall & Anti Room For Agniveers with precast construction technology (2D) permanent specification for Storey RCC Framed Structure all as per design basis report, detailed in scope of work and other documents of the tender complete all specified and directed.

Rain Water Harvesting

SEWAGE

Excavating in trenches in any type of soil , n exc 1.5 m wide and n. exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soil complete all as specified and as directed.

Excavating in trenches in any type of soil , n exc 1.5 m wide and exc. 1.5 m in deep and n.exc 3.0m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out soil complete all as specified and as directed

Returning, filling in, including spreading ,leveling, watering and well ramming in layers n. exc 25 cm with soil complete all as specified and as directed.

Removal of excavated material (soil) to a distance exc 50 m n. exc 250 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

M&L for concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 complete

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.

M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:4).complete all as specified and as directed.

M&L, 15mm thick rendering on any faces of stone, concrete or brick work in CM 1:4 surface finished even and fair complete all as specified and as directed. .

M&L for 15 mm thick rendering in cement mortar (1:3) on brick / concrete/ stone surfaces mixed with water proofing compound as per manufacturer instruction , finished even and smooth using extra cement complete all as specified and as directed.

Supply only water proofing compound.

Use & waste formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter

M&L for cement concrete type C2 1:3:6 (40mm graded stone aggregate) in foundations, filling and mass concrete complete

M&l for cement concrete 1:2:4 type B1 (20 mm graded stone aggregate) as in coping complete

S&F TMT steel bars 6 to 8mm in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified and directed

S&F TMT steel bars 5mm dia and over, up to and including 10mm dia in stirrups spcers and binders.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part VI

(Area Drainage)

Supply and fixing stop valves 20mm, chromium plated fancy type cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and connected items complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

M&L PCC in foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) all as specified

M & L 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces and finished the surface even & smooth without using extra cement complete all as specified and directed.

M&L RCC M - 25 (Design Mix) (20mm graded agg) as in footing etc complete.

M&L RCC M - 25 (Design Mix) (20mm graded agg) as in walls, retaining walls, basement walls, and the like , of any thickness including attached pilaster and butresses, footing etc complete.

Use & wate formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batte

Use & waste formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter

M&L Precast cement concrete Type B-1 1:2:4 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:6 complete all as specified and as directed.

M & L for Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9 mm dia or securing with clips complete.

Returning filling in including spreading levlling ,atering and well ramming in layers nexc 25cm thick complete all as specified and directed.

Total carried over to BOQ Rs.

Signature of Contactor

Schedule 'A' Part VII

(Security Fencing & Gate)

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft /loose soil , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as directed.

S&F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;MS angle iron in "Y" shape posts and struts in fencing including cutting tops to shape as directed including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete as directed.

S&F framed work as in doors or gates of angle or other section with gussest plates, rails, braces, etc, complete drilled for fixing and incl steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hanging door fittings and fixing complete conferming to gde Fe 410-w

Supply of Chain link MS galvanisd fencing, any size or type complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed

Total carried over to BOQ Rs.

Signature of Contactor

Item No 1 (C): Designing (Structurally & Aesthetically) and construction of block of Cook House For Agniveers with precast construction technology (2D) permanent specification for Storey RCC Framed Structure complete all as per design basis report, detailed in scope of work and other documents of the tender complete all specified and directed.

(Summer & cooling Applinces)

eater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc all as specified and directed.

S & F Rotational moulded PVC water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 ltrs with suitable size angle iron stand, height the stand suitable for solaar water heater of capacity 500 LPD complete specified and directed.

Supply and fix electric water h

Per Qtl

Supply, installation,commissioning hi wall split units capacity 2.0 TR indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 4 star rating and EER 3.2.of capacity complete all as specified and directed.

Supply only bottled water dispenser, having option of dispensing hot and cold water with cooling capacity 3 ltrs/hr and tank capacity of 3.4 ltrs, heating capacity 6 ltrs/hr and tank capacity 1.6 ltrs, working in R - 134a refrigerant all as specified and directed.

Supply, installation,commissioning Deep freezer hard top more than 320 litre and up to 400 Litre capacity having double door all as specified and directed.

Supply, installation,commissioning of Water cooler fully stainless steel, electric driven and single phase having approx storage 80 litres and nominal cooling capacity 40 Litres per hour all as specified and directed.

Supply, installation,commissioning of Water cooler fully stainless steel, electric driven and single phase having approx storage 120 litres and nominal cooling capacity 60 Litres per hour all as specified and directed.

Supply and fixing GI fixing GI tubing mediium grade 25mm bore with fitting and connected items connecting with rotational moulded PVC water storage tank as inlet and outlet for backup stainless steel hot water tank complete all as specified and directed.

Supply & lay Hot water pipe duly insluted with glass wool and aluminium cladding 15 mm bore complete all as specified and directed.

Supply & lay Hot water pipe duly insluted with glass wool and aluminium cladding 20 mm bore complete all as specified and directed.

Supply and fixing stop valves 25mm, chromium plated fancy type cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and connected items complete all as specified and as directed.

Total carried over to BOQ Rs.

Signature of Contactor

(using 20mm graded crushed stone aggregate) of size 230x200x100mm incl provn of hinges welded with angle iron frame and MS cover 3mm thck sheet, MS handle of suitable length and size welded with MS cover and suitable locking arrangement and applying two coats of synthetic enamel paint over a coat of red oxide primer including necessary excavation and earth work in soft/loose soil complete all as shown on drawing and as specified.

Item No 58 : Table Dining 6 persons FD-376

Security Fencing & Gate

Excavation in post holes (or similar holes) each n.exc. 0.50 Cum in

self/loose soil getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 CM, watering and removing surplus soil, to a distance n.exc. 50 M. and making good surplus complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

S&F framed work as in door or gates of angle or other section with gusset places, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including hooks, hinges complete all as specified and directed by Engineer-in-Charge. (for tree guard)

Total carried over to BOQ Rs.

Signature of Contactor

Item No 12 : Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying one coats of black bituminous paint complete all as specified and as directed.

The panel should withstand Hydrostatic pressure of atleast 4 times the working load and should be provided with HDG bolts, nuts, washers, food grade foam gasket, cleats, including PVC pipe support of 110mm dia for the roof of top panels. Tank shall be erected on steel base at site as per manufacurer's specifications & design. Provision of holes for inlet and outlet, overflow should be made as per direction of Engineer-in- Charge and including connecting with 9" long thread end Nipple complete all as specified & directed by Engr in Charge. The Tank installation work will be carried out at roof of building/ ground level.

FIRE FIGHTING SYSTEM

(FIRE FIGHTING SYSTEM)

S & F for MS ERW pipe 50 mm dia as per IS 1239 including cutting /threading/welding etc for providing connections and including all types of reqd fittings , clamps, nout & bolts etc for laid on wall/ceiling/ floor/ all as specified and directed.

S & F for MS ERW pipe 25 mm dia as per IS 1239 including cutting /threading/welding etc for providing connections and including all types of reqd fittings , clamps, nout & bolts etc for laid on wall/ceiling/ floor/ all as specified and directed.

S & F Valve,gate/ball, screwed,15 mm, brass with iron wheel head, screwed both ends for iron/MS pipe and complete all as directed.

S & F Valve,gate/stop, screwed,50 mm , brass with iron wheel head, screwed both ends for iron pipe and complete all as directed.

M & L for RRL hose reel of 20 mm dia 30 mtr long including hose box conforming to IS - 5132 complete all as specified and as directed.

Total carried over to BOQ Rs.

Signature of Contactor

Item No 13 : Supply, Installation, Testing and Commissioning of silent Diesel Engine driven generating set not less than 20 KVA or nearest standard size, 415 volts, 3 phase 4 wire, 1500 rpm, 50 Hz power supply with power factor 0.8 couple directly to alternator mounted on a common base plate complete with integral acoustic enclosure having silent features such as modular bolted construction with fabrication on imported CNC torret punch machines, nine tank treatment process with pure polyster based powder coating to ensure long life in all weather conditions and for out door application/ installation, integrated design thereby facilitating /easy handling installation & shifting of the equipment at site.

r 10cm in width or girth,not otherwise described incl preparation of surfaces, appying red oxide primer 01 coat, and 02 coat of synthetic enamel paint complete all as specified and as directed.

Per sq Mtr

Lightning protection system

(Lightning protection system)

Supply & fix aluminium strips 25x3.15 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as directed by Engr - in - Charge .

S&F test point terminal block made out of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw , drolled , cutting upper & lower portion for incoming & outgoing including double insulators two coat of synthic enamel paint complete as directed .

Total carried over to BOQ Rs.

Signature of Contactor

Item No 14 : M&L for 100 mm thick PCC 1:2:4 TYPE B1 using 20mm graded stone aggregate as in floor/hard standing.

(Site Clearance)

Road Path Culvert

Suraface excavation n.exc 30 cm deep and averaging 15 cm and getting out in soft soil.

Excavating over areas, n exc 1.5 m deep and getting out soft/loose soil

Earth filling (for site development) incl raising (or lowering) not exc 1.5 m high earth spreading in layers n.exc 30 cm thick watering and rolling and finishing to reqd size and shape etc

Total carried over to BOQ Rs.

Signature of Contactor