PROVN OF VEH REPAIR BAY AT EMT, TOILET BLOCK WITH ALLIED WORK AT 16 JAT AND OTHER SANCTIONED WORK AREA OF AGE BR-II UNDER GE (EAST) LUCKNOW

Amount

Surface excavation soft/loose soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation, trenches etc and getting out in soft/loose soil complete all as specified and directed.

Removing of excavated materials to a distance 1.5km and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed.

Earth filling under floor, including spreading, leveling, watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed. Note : earth obtaind from excavation under item No 1 & 2

M&L for cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations filling, sub base and mass concrete filling, etc complete all as specified and directed.

Excavation over areas, n exc 1.5 m deep and getting out in soft/ loose soil complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement cut to length, bent in shape required including cranking, bending, spirally hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Description all as per item No 8 above but mild steel TMT bar 6 mm to 8 mm dia.

Ditto as per item 8 above but 6 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders

M&L for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in foundations, footings, plinth beams; bases forcolumns, etc.complete all as specified and directed.

M&L for RCC 1:1½ :3 type A1(using 20 mm graded stone aggregate) as in Column, pillars, piers, posts and struts etc complete all as specified and directed.

M & L for RCC 1:1½ :3 type A1 (using 20 mm graded stone aggregate) as in roof slabs, shelves etc complete all as specified and directed.

M & L for RCC 1:1½ :3 type A1 (using 20 mm graded stone aggregate) as in chhajas etc complete all as specified and directed.

M & L for RCC 1:1½ :3 type A1 (using 20 mm graded stone aggregate) as in Roof beam, bands, lintel beam etc complete all as specified and directed.

M&L for formwork to sides of concrete in foundations, footings, bases of columns, sides and soffits (if any) plinth beams, and similar work complete all as specified and directed

M&L for formwork to sides of concrete of pillars, posts, struts, piers, columns etc complete all as specified and directed.

M&L for form work to soffits of roof slabs, floor slabs and similar work n exc 200 mm thick fair finished surfaces (flat) complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for formwork to edges of concrete flats, roofs and sides of RCC/ PCC bands in walls, and similar work exc 200cm wide complete all as specified and directed.

M&L for formwork to edges of concrete flats, roofs and sides of RCC/ PCC bands in walls, and similar work exc 10cm but n exc 20cm wide complete all as specified

Ditto as per item 22 but exc 5 cm but n exc 10cm wide complete all as specified

M & L brick work with fly ash bricks, straight or curved on plan exc 6M mean radius, old size brick built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius as in half brick thick wall built in CM 1:4 complete all as specified and directed.

M & L PCC 1:2:4, type B-0, with 12.5mm stone aggregate 40 mm thick in Damp Proof Course to horizontal or vertical surfaces including necessary formwork using water proofing compound as per manufacture's instruction complete all as specified and directed.

M&L for plastering 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces, finished the surface even and smooth with using WPC @ 2% by weight of cement complete all as specified and directed.

M&L for plastering 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces, finished the surface even and smooth complete all as specified and directed.

M&L for 15 mm thick cement plaster on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth complete all as specified and directed.

M & L rendering 5mm thick in CM 1:3 as in ceiling ,soffits of slab and finish the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick cement plaster in CM 1:3 on top of RCC Roof Slab with using water proofing compound 3% by weight of cement, finish the surface even & fair complete all as specified and directed.

M&L for 100mm thick PCC 1:5:10 type E-2 using 40mm graded stone aggregates as in sub base of floors complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregates as in base of floors / padding, finished the surface even and rough complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300x600x 7mm thick including 10mm thick screed bed in CM 1:4 on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and drected.

M&L for non skid ceramic coloured tiles 400x400x 7mm thick in floors etc. including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection laid in bays not exc 1.5m with expansion joints 30x10mm filled with mixture of hot bitumen and sand, finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for hard core broken stone of gauge n. exc. 63mm, deposited, spread and levelled in layers n. exc. 15cm thick, water and rammed to a true surface complete all as specified and directed.

Supply only integral water proofing compound (ISI marked) complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

Description all as per item No 39 above but applying three coats of white wash on ceiling and ditto

Description all as per item No 39 above but applying two coats of cement based paint over one coat of Primer on wall

S&F 15mm dia tubes medium grade galvanised, with all fitting and fixed complete to walls/ ceilings/ concealed or laid in floors complete all as specified and directed.

S&F 20 mm Tubes medium grade galvanised with all fitting and fixed complete to walls/ ceiling / concealed or laid in floors complete all as specified and directed.

S&F 500 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)in white colour triple layered, hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20 mm dia brass gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, complete all as specified and directed.

S & F pillar taps cast copper alloy with capstan heads chromium plated screwed down hidh pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed (15mm Bore dia of pipe )

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed ( 32mm)

S & F 32 mm bore Low density polyethylene pipes for Wash hand basin etc complete all as specified and directed.

S&F Vitreous China urinals, half stall type (flat back), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.

S&F Vitreous china sqatting pan, Orissa pattern, size 580 x 440 mm white , with integral foot rests including trap (excluding flushing cistern and flush pipe ) complete all as specified and directed.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of capacity 10 litre ISI marked complete all as specified and directed. Make :- Commander/Hindware/Jindal

S & F 20 mm dia float valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe with fly nuts complete all as specified and directed.

S & F Long body Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle sc-rewed down screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe ) complete all as specified and directed.

S & F in repair 15 mm bore Stop valves (angle type) cast copper alloy chrominum plated fancy type screwed down high pre-ssure with crutch or but terfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F PVC (SWR) floor trap, plain with CP grat-ing including joint-ing with solvent cement ( Diameter of outlet 75mm)

S&F CP Brass toilet paper holder of superior quality complete all as specified and directed.

S&F CP Grating doom of 125 mm dia complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single T, equal or unequal complete all as specified and directed.

S & F110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & FSolid uPVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed.

S&F Factory made soild uPVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F steel windows with side hung shutters including projection type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welding complete as specified and directed.

S&F steel windows with side hung shutters including projection type hinges with steel handle and steel peg stay complete without glazing bars dovetailed and welding complete as specified and directed.

S&F Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work including drilling conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 200 mm long Aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long alluminium handles, cast type, anodized and fixed complete all as specified and directed.

S& F 100 mm size butt hinges, medium weight, stainless steel, and fixed complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complet all as specified and directed.

S&F stainless steel steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of Red oxide primer over steel surfaces including preparation of surfaces all as specified and directed.

M&L for 10 mm thick screed bed on green concrete surface in cement mortar 1:4 with water proofing compound & finished surface even and smooth without using extra cement complete all as specified and as directed.

M/L for roof treatment with polymeric water proofing mem breane with certain specification given below as under complete all as specified & directed) (a) Applying a coat of bitumenous primer @ 0.50 LTRs /Sqm and allow to dry (c) Applying a coat of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm. (d) Supply and laying APP based polymeric water proofing membrace, weight not less than 3.00 kg/sqm and and minimum 3 mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) sealed the side laps with spread temper (e) applying a tack coat of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm

M&L for cement concrete type B-1 1:2:4 as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets, copings, surface channels and drains, benching of man holes, laid to shape and slope and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L PCC 1:4:8 type D-2, using 40mm graded stone aggregate as in bed of drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia of pipe complete all as specified and directed

M&L for 150 mm dia salt glzed stoneware drain pipes grade ‘A’ laid in trenches and jointed in cm 1:1 complete all as specified and directed.

M&L for providing pre-cast RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for man holes and drains) including necessary form work set in CM 1:4 complete all as specified and directed.(Note :- Reinforcement shall be measured and paid separately)

Construction of Septic tank for 50 user's all as shown in drawing No (as per CELZ TD-217 Sheet No 1/2 & 2/2) and as specified and directed.

Construction of Soak well of size 1.20 Mtr dia and 4.50 Mtr deep all as shown in drawing No (CELZ TD-576 Sheet No 1/2 & 2/2) and as specified & as directed.

M&L 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base of floor complete all as specified and as directed.

S&F 60 mm thick, machine pressed rubber moulded, glossy coloured, precast conctete interlocking paver block any shape and size of M-35 grade of approved shade laid over 50mm thick sand cushion and filled with fine sand complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in floor topping/hard standing laid in alternate bays all as specified/directed.

M&L PCC 1:5:10 type E-2 using 40 mm graded stone aggregate as in foundation filling/sub-base to floor etc and mass concrete complete all as specified and as directed.

M&L for 75 mm thick P.C.C 1:2:4 type B2 using 40 mm graded stone aggregate as in floor of ramp and spike rolling to surfaces or making impressions of expanded metal, while the concrete is green etc complete all as specified and directed.

M&L 100 mm thick plain cement concrete type D2 1:4:8 (using 40mm graded stone aggregate)as in sub base complete all as specified and directed.

M&L 100 mm thick plain cement concrete type C2 1:3:6 (using 40mm graded stone aggregate)as in sub base complete all as specified and directed.

M&L precast conctete coloured rubber moulded Paver block any shape and size conforming to IS 15658-2006 of 80mm thickness,M-40 grade in set jointed and pointed with grey cement slurry and pigment to match the floor approved design /colour set and bedded over and including 25mm thick coarse sand laid over compacted sub soil complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars , etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc but lime plaster any description complete all as specified and directed.

M&L for prepration of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10cm width or girth complete all as specified and directed.

Taking Down Chowkats or frames not exc. 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking downChowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters from the frames complete all as specified and directed.

M&L factory made 32 mm thick flush shutter solid core construction with block board core and plywood face panels, both faces covered with decorative face veneer with lipping,complete all as specified and directed.

S & F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed.

S&F hold fasts; supports or stays for rainwater, knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone for embedding of hold fast etc complete all as specified and directed.

S&F 300 mm long Aluminum alloy, anodised sliding door bolts, plate type, ,and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminum alloy complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick Sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and directed.

M&L for Pressed steel frames (size of frame 125x60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

M&L for filling cement concrete type B0 in steel door frame or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L mild steel 300mm ordinary rat tail rod patttern springs includding roller and roller plate complete all as specified and directed.

M & L for preparing new plastered or unplastered wall surfaces and applying two coats of oil -emulsion distemper over a coat of putty primer complete all as specified and directed.

M & L for Reinforced cement concrete (nominal mix) type B1 1:2:4(using 20mm graded aggregate) in Chimneys and shafts

S&F frame work as in door or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering.Doors, etc to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fitting and hanging, alsofasteningand fixing complete

S & F Mild steel, 1.6mm thick, plain,black sheet in wall cladding, steel gates and similar work,cut to size, holes punched; including round headed screws clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams,including bending or turning up, mitred angles, etc. as required

Material and labour for point wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3 mm thick plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for one light / fan point controlled by one, one way switch 06 Amp.

All as per serial item No 112 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.

All as per Serial Item No 112 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket outlet point controlled by one, one way switch on independent board complete all as specified and directed.

Supply and fix switch piano flush type, 06 Amp, single pole, one way, 230 Volt complete all as specified & directed.

Supply and fix socket outlet 2 in 1, 5 pin, 06 Amp, flush type, 230 volt complete all as specified & directed.

Supply and fix switch socket combination outlet 2 in 1, 3 pin, 06 Amp and 16 Amp flush type, universal, 230 volt, four hole complete all as specified & directed.

Supply and fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting Wiith LED lamp 12 W complete all as specified & directed.

Supply and fix in replacement of single side connection LED T8 tube light rod 20 Watt, 6500K of four feet long into and including LED tube light fixture of four feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed. Make : Crompton, Cat No : DMLN1LT8-16& LT8-20-865-2 or equivalent in Havells, Cat No : REGALBATTENT8UPT01X22WSSBS & PHOTONULTRA1213T8SSTL20WLED865SPC, philips cat no TMC 100 1xT LED /MAS LED tube 1200 mm 18 w 865 T8 I - 2100 Lumen

Supply and fix in replacement of single side connection LED T8 tube light rod 10 Watt, 6500K of two feet long into and including LED tube light fixture of two feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed. Make : Crompton, / Havells,/ philips

Supply and fix in replacement of LED security light fitting 45 watt, 5700K with IP 66 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed. Make : Crompton, Cat No : LSTP-45-CDL or equivalent in Havells/ philips

Supply and fix exhaust fan 300 mm sweep 230 volt AC 1400 RPM heavy duty complete all as specified & directed.Make:- Usha/ Bajaj/Orient/CG

Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

Material and labour for wiring for circuit / sub main wiring with 2 x 4.0 Sq mm alongwith 1 x 2.5 Sq mm earth wire of FR PVC insulated copper conductor, single core cable drawning into PVC concealed conduit including cutting chases for concealed conduit wiring and making good complete all as specified & directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 240 volt, 20 Amps complete all as specified & directed.

Supply and fix in replacement of sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

Supply, laying, testing and commissioning LT underground XLPE insulated, armoured heavy duty electric cable with aluminium stranded conductor, 1100 volt grade conforming to IS-1554 and ISI marked of cross sectional area 10 Sq mm 2 core size in trenches, on wall, road crossing through protection pipe etc. complete all as specified and directed.

Providing sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed.

Supply and laying 50 mm bore galvanised steel tubes with all fittings, light grade laid in trenches for cable protection complete all as specified and directed.

Supply and laying common burned clay bricks sub class B designation of old size bricks complete all as specified and directed.

M/S Reliance Construction

pratap associates

QUALITY CONSTRUCTIONS CO