PROVISION OF 01 TEA ROOM FOR OFFRS NEAR BLDG NO 52 MAIN OFFICE, TWO TOILET BLOCKS IN FRONT OF POP GROUND, CONSTRUCTION OF WASH ROOM NEAR QM STORE AT NCC OTA, SPECIAL REPAIRS OF SECURITY WALL WITH V ECK AND CONCERTINA COIL ----GE KAMPTEE

Amount

Excavation in trenches n exc 1.5m in deepth and 1.5m in width and getting out in soft/loose soil complete all as specified and directed.

All as per item No 1 here in above but each additional 1.5 m or part thereof in depth beyond the first 1.5m all as specified and directed

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone agg) in foundation, mass concrete and filiings complete all as specified and directed.

M&L Form work to side of concrete in fdns, footing base, base of columns, side and soffits of plinth beam and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) as in footing, foundation, beams, plinth beams, base for columns and mass concrete etc complete all as specified and directed.

M&L Form work to side of columns and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) as in columns and pillars etc complete all as specified and directed.

M&L Form work to side of sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) (using 20 mm graded stone aggregate) as in Beams, cantilevers, ressummers, lintels over 1.5m span concrete etc complete all as specified and directed.

M&L Form work to chullah hoods, chajjas, troughs and similar items including edges and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) (using 20 mm graded stone aggregate) as in chajja etc complete all as specified and directed.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L Formwork to Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) (using 20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F milt steel TMT bars 10 mm dia and over , cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F milt steel TMT bars 8 mm dia in spacers, cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia.

S&F mild steel TMT bars 8 to 10 mm dia a as in stirrups, spacers and binders.

M&L for brick with fly ash brick old size straight of curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and as directed.

All as per item No 18 here-in-above but half brick wall in CM 1:4.

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth withot using extra cement.

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:4 mixed with WPC finished even and smooth without using extra cement complete all as specifed and directed. (Note : WPC will be measured & paid separately).

Supply only Liquid water proofing compound of approved quality.

M & L for rendering 10 mm thick on surfaces of ceiling in cement mortar (1:3) and surfaces finished fair and even complete all as specified and as directed

M & L for prepartion of new plastered surfaces on wall and applying two coats of oil bound distemper over a coat of Primer complete all as specified and directed.

M&L for Preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

M&L Preparation of new plaster surfaces on wall and apply two coat of cement base paint over a coat of primer compete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M&L hardcore of gauge n.exc. 63mm deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface for plinth protection/path

M&L for 75 mm thick Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floors finished even complete all as specified and directed.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding. 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15 mm thick screed bed of cement mortar (1:6) etc complete all as specified and as directed.

M&L coloured glazed ceramic tiles 300x450x6 to 7mm thick, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10mm thick in CM 1:4 complete all as specified and directed.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (40 mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as spd and directed.

Material and labour for PCC 1:2:4 type B1 (using 20mm graded stone aggregate as in cills, steps, parapets and copings, kneelers, bed plates, hold fasts block, filling on pressed steel door frame etc complete all as specified and as directed

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10 mm dia as tle bar complete confirming to Fe-410 -O etc complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suppling and fixing in opening as per specification and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 4mm thick moulded laminated PVC Sheet on the front face & 4mm plain colour PVC sheet on back face, with wood free EPS supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm long medium weight cold rolled mild steel butt hinges complete all as specifed and directed.

S&F Extruded Aluminium alloy handles, fabricated type anodised of 150mm long complete all as specifed and directed.

S&F Aluminium anodised barrel tower bolts of extruded section and fixed of 150mm long complete all as specifed and directed.

Aluminium alloy, anodised, 250mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed and directed.

S&F steel window with side hung shutters including projecting or box stype hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer including fixing of hold fast of size 25 x 5 mm flat iron etc all complete all as specified and directed.

All as per item No 41 but without glazing bars complete all as specified and directed

S&F steel ventilator with top hung shutter including hinges peg stay to receive glazing or gauzing and one coat of primer including fixing of hold fast size 25 x 5 mm of flat iron etc complete all as specified and directed

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 as specified

S&F 4.00mm thick glass pane ordinary quality and glazing with oil putty in square n. exc 0.5 sqm each pane complete all as specified and directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed

M&L for preparation of newly steel surface apply two coat of synthetic enamel paints over a coat of red oxide primer.

M&L preaparation of newly steel surfaces of any descrip[tion over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

S &F Towel Rail 20mm dia of Chromium plated fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specifed and directed.

Supply & fixed in vitreous china wash down water closet (pedestal pattern) 'P' or 'S' trap including jointing including plastic water closet seat, closed pattern with flat bottom and cover and mild steel CP or aluminimised hinging device complete

S & F in repairs vitreous china white squatting pan "Orissa Pttern" size 580x440mm, with integrated foot rest (excluding flushing sistern, flush pipe etc) including making good to floor complete, all as specified and directed.

M&L Cast Iron 'S' trap, including jointing with solvent cement of 100 mm dia complete all as specifed and directed.

S & F 10 ltr cap PVC valve less symphonic action type flushing cistern low level, white with inlet ball valve float and handle including bracket etc complete all as specified. Make :Prayag or equivalent

Flushing pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specifed and directed.

S&F PVC connection 15mm size, 600mm long with PTMP nuts both side complete all as specifed and directed.

S&F Sink with drainage board made of stainless steel thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm incl waste pipe 32mm dia complete all as specified and directed.

S & F waste fitting, 40mm brass, chromium plated for sink, basin, etc with long screwd shank and fly nut compete.

S&F Wash Basin oval type (56x41cm) including waste cupling and waste pipe complete all as specified and directed (Make : Hindware, CERA, Prayag )

S&F pillar cock tall height fancy type cast copper alloy, chromium plated 15mm dia of bore complete all as specifed and directed.Make : (Make : Hindware, CERA, Prayag )or equivalent

S&F Vitreous China urinals, halft stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

S&F 15 mm bore CP Urinal spreader for urinals complete all as specified and directed

M&L for Machine cut cudappa stone slab 20-25mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S&F pre-polished granite 20mm thick fixed on platform/shelves over 20mm thick screed bed in cement mortar 1:6, if directed by Engr In Charge including necessary moulding etc complete all as directed.

S&F Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed of 1000 litres capacity.

S&F ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of size 20mm dia complete all as specifed and directed.

S&F bib taps fancy type chromium plated, with crunch or butterfly handle screwed down,screwed for iron pipe or for brass ferrule and fixed of 15mm bore size complete all as specifed and directed.

S&F stop/angle cock fancy type chromium plated, screwed down, high presure with cruntch or butterfly handle screwed both ends for iron pipe of 15mm bore pipe complete all as specifed and directed.

M&L 15mm GI tubing 'Medium grade' with all fiting and fixed complete tom wall and celing or laid in floor of fllowing sizes complete all as specifed and directed.

As per item no 68 but 20mm bore complete all as specifed and directed.

S & F 110 mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints, fixed to walls with stack clamp every one mtr apart complete all as specified and as directed.

S&F PVC (SWR) pipes of 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specifed and directed.

M&L PVC (SWR) floor trap, plain with grating including jointing with solvent cement of 75mm dia complete all as specifed and directed.

S&F CP grating of size 100mm dia complete all as specifed and directed complete

S&F PVC cowl slotted vent cowl 110 mm size complete all

M&L Salt glazed stoneware drain pipes laid in trenches and jointed as specified of 150mm dia all as specified and ditected

M&L Concrete bed to 150mm drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in complete in PCC(1:3:6) type C-2 all as specified and directed.

M&L for precast RCC 1:2:4 type B1 using 20mm stone aggregate as in landings, cover slabs, for manholes etc and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) n .exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and directed.

M&L for provision of water proofing treatment by using APP torch on non woven polyster film reinforcement with 3 mm thick and weight not less than 3.50 kg/sq m over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane laid with 100 mm over lap on both sides all as per manufacturer's instructions including 15mm thick screed bed in CM 1:4 and aluminium paint of 0.2Kg/Sqm over membrane complete all as specified and directed.

Demolition of brick work, built in cement mortar or cement lime mortar including all quoins, pillars etc. and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 50m as directed by the Engineer-in-Charge.

Taking down cement Plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of debris, complete all as specified and as directed

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed

S&F wire netting of galvanised steel wire 0.71 mm dia and size of mesh is 12 mm fixed in properly with suitable nails for repair of cracks at various locations in wall, beam,chajja, facis, slab, lintel etc including taking down plaster of cracked portion and making good the area by rendering in CM 1:3 complete all as specified and directed.

M&L complete removal of existing treatment of old plastered surfaces on wall including brooming down or steel wire brushing ,scraping down moulds , washing down and applying two coats of exterior grade acrylic emulsion weather proof paint over a coat of acrylic primer complete all as specified and directed.

M&L Preparation of new plaster surfaces on wall apply two coat of cement base paint over a coat of primer compete all as specified and directed.

Material & Labour for complete removal of existing treatment of old decorated wall surfaces and applying two coat of cement base paint over a coat of cement primer

M&L for Providing precast cement concrete type B0 1:2:4 (12.5mm graded aggregate) in CM 1:4 louvres and jallies, 35mm thick (measured solid), including all mouldings but excluding frame and complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for in any position complete all as specified and directed.

M&L for cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar exc one brick but not exc two brick inserting holdfasts and making good dismantlked portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

S&F Mild steel angles, including embeding in concrete and screwing etc. including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 all as specified and directed

S&F Punched tape Concerttina Coil (including spike and handle) with 56 loops and dia 600mm,max covered length 8 RM, having a core wire of high carbon spring steel of high tensile strength. The punchedtspe and copre wire ( 2.5 +_ 0.35 mm dia ) shall be heavy galvanized (IS-1730) (wire-275 GSM & strip-200 GSM) to provided protection against out door exposure. The punched tape shall mechanically crimped over the core wire and then formed into a coil at various parts of the periphery of the coil. The of strip as 19 mm and spacing of blades 24.00 +_ 0.5 mm C/C. The weight of each coil shall be 8 +_ 5 % kgs without packing material and coil length 8 mtr (maximum) when opened up each coil would with bituminized hessian cloth for providing protective packing ref specification No CQAE/5660/1602/A for raw material and drawings IMGA-0112/B (Sheet 1 of 2),IMPD-1821,IMPD-1822 complete all as specified and directed

M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F galvanised two strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolt including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc., as directed

M&L for preparation of newly steel surface apply two coat of synthetic enamel paints over a coat of red oxide primer complete all as specifed and directed.

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint etc complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

S&F pre-polished granite 20mm thick fixed on platform/shelves over 20mm thick screed bed in cement mortar 1:4 including necessary moulding etc complete all as directed.

Demolition of un-reinforced cement concrete in any description and in any position and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 m as directed by the Engineer in Charge.

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) in foundations, filling and mass concrete/sub base complete all as specified and directed.

M&L for providing cement concrete1:2:4 type B1 (20mm graded aggregate) as in copings,plinth courses including weathering,slightly rounded or chamfered angles and throating on edges complete all as specified and directed.

M&L point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch.(Cable Make : Polycab, Havells, Finolex, L&T, Legrand) (PVC Conduit Make : Polycab, Modiplast, Finolex) Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

All as per item Sl No 103.00 here in before but One ceiling/exhaust fan point controlled by oneway switch and regulator.

All as per item Sl No 103.00 here in before but One 3 pin 5 amp socket outlet point on the same board with other switches.

All as per item Sl No 103.00 here in before but One 3 pin 5 amps socket out let point on independent board.

All as per item Sl No 103.00 here in before but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point.

M&L for sub main wiring with two single core PVC FR LSH insulated unsheathed stranded copper conductor and earth wire 1100 volt grade and drawing into PVC conduit not less than 20 mm medium grade concealed in wall of the following sizes :- 2x4.0 Sqmm with earth wire of 1x4.0 Sqmm. (Cable Make : POlycab, Havells, Finolex, L&T, Legrand) (PVC Conduit Make : Polycab,Modiplastr, Finolex) Note :- Accessories for point/sub main wiring like PVC junction box, bend, Tee, elbow shall be of same make.

S&F for switch modular type single pole one way 6 amp 1 module 250 volts AC suitable for modular switch boxes all as specified and as directed by EIC. Make: IndoAsian / Elvira / legrand/ Crabtree.

S&F for socket modular type single pole one way 6 amp 2 module 3 pin 250 volts AC suitable for modular switchboxes all as specified and as directed by EIC. Make: IndoAsian / Elvira / legrand/ Crabtree.

S&F for switch modular type single pole one way 16 amp 250 volts AC suitable for modular switch boxes all as specified and as directed by EIC. Make: IndoAsian / Elvira / legrand/ Crabtree.

S&F for socket modular type single pole one way 6/16 amp 2 module 3 pin 250 volts AC suitable for modular switchboxes all as specified and as directed by EIC. Make: IndoAsian / Elvira / legrand/ Crabtree.

Supply and fix ceiling rose surface type three terminals 5 amps Make :- Anchor/Roma/Legrand/Havells/IndoAsian

Supply and fix Fan step regulator, 120W - 2 module complete all as specified and directed Make :- Legrand/Crabtree/IndoAsian

Supply and Fix Highly durable surface mounted 18/20 watts LED batten constructed of fire retardant engineering grade extruded aluminium body 100 lumen per watt and decorative end cap complete with tube rod,driver including 3 core 1.0 sqmm copper conductor cable for connection and accessories all as specified and directed. Make:- Philips/Jaquar/Wirpro/Syska/Halonix

Supply and Fix Highly durable surface mounted 09/10 watts LED 2 feet batten constructed of fire retardant engineering grade extruded plastic and decorative end cap complete with tube rod,driver including 3 core 1.0 sqmm copper conductor cable for connection and accessories all as specified and directed Make:- Philips/Jaquar/Wirpro/Syska/Halonix

S & F LED light fitting 9W/10W bulkhead luminaires with lamp holders etc complete with all accessories and including connecting up with twin core twisted flexible cable suitable size of 230 V 50 Hz complete all as specified and directed.Make:- Philips/Jaquar/Wirpro/Syska/Halonix

Supply and fix ceiling fans, complete with three blade, down rod, all accessories 230V, 1200mm sweep, with Squirrel cage induction motor connecting with celing rose with 3 core 1 sqmm copper conductor complete all as specified and directed. Make :- Havels / Usha / Crompton

S&F Exhaust fan , made of metallic body 300mm sweep, with louver shutters single phase, 230 Volts, 50Hz, with nut and bolts, washers etc., and connecting up with twin core twisted flexible copper conductor cable of suitable size from fitting to ceiling rose, complete all as specified and as directed. Make :- Havels / Usha / Crompton

M&L for making hole of suitable size for 300mm sweep exhaust fan and including grouting bolts, cutting chasing and plastering, painting etc., to match with the existing surface, complete all as specified and as directed.

Supply and fix sheet metal enclosure IP 43 single pole & neutral for 240 volts 4 way with 200 Amp rated bus bar flush /surface mounting, double door Make- Legrand/C&S /L&T

Supply and fix MCB single pole 240 volt 6 to 40 amps 10 KA. Make:-Legrand, L&T, C&S

Supply and fix MCB single pole and neutral 240 volt 6 to40 amps 10 KA breaking capacity, 'C' series, complete all as directed by the Engineer-in-Charge. Make-Legrand/ Siemens/ Schneider

Earthing complete with galvanised steet earth plate electrode 600x600x6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanised earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric (d) Funnel with watering pipe of GI 20mm nominal bore light grade and copper lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protec-tion pipe 7.50 metre long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs. 34,325.00]

M/s T.S.JOHAR

Krishana electronics

Bidder Name

M/s M.G. Hargunani

M/s T.S.JOHAR

Krishana electronics