Supply, Carriage and Installation of prefabricated hut of one No Control Room with attached washroom for service providers for issuance of Smart Cards and for Prepaid Booking including one no. shed for Parshad sale counter at Lower Holy Cave

Amount

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes Make-JINDAL/TATA/SAIL/JSW)

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of nuts & bolts. Welded (Make-JINDAL/TATA/SAIL/JSW)

Providing and fixing PUF insulated sandwich panels for walls and roofing of total thickness not less than 50 mm. Panel shall have 0.5 mm thick precoated GI sheet on both side of Polyurethane foam confirming to IS 12436: 1988. The PPGI sheet should have plastic protective guard film of minimum 25 microns to avoid scratches while transportation . The PU foam shall be self-extinguishing, fire retardant. Also all joints of roofing would be fill with silicon . (Make- Jindal mectec /E Pack polymers/Modern Prefab systems)

Providing and fixing of 1.2 mm thick PGI sheet U-section 40x52x40mm over all sides of PUF panels with proper riveting having spacing of 500 mm

Providing and fixing of 100 mm x 2 mm thick MS sheet on every joint of PUF panels of walling & roofing from inner and outer side including cost of cutting, punching etc complete

Providing and fixing precoated galvanised steel sheet roofing accessories 1 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete

(i) Ridges plain (500 - 600mm)

(ii) Flashings (150 mm wide

Supply and fixing of door composited with 50mm PUF panel (polyurethane foam conforming to IS 12436:1988 and PPGI sheet conforming. Sheet shall have guard film of 25 micron to avoid scratches during transportation).Doors with frame work of Aluminum anodized channel (profile) of 60mmx40mmx2mm thick including cost of 02 Nos. Anodised Aluminium handles 125 mm, 02 Nos. Anodised Aluminium sliding door bolt 250 x16 mm , 02 Nos. Anodised Aluminium tower bolt (barrel type) 200 x10 mm, 04 Nos. Anodised Aluminium butt hinges 75x45x3.2 mm etc complete.

(Doors of size 1.00mx2.10m) including cost of frame etc complete

(ii) (Doors of size 0.75mx2.10m) including cost of frame etc complete

Supply and fixing of Double leaf Window of size 1.00mx1.00m composited with milld steel ERW pipes for frames of sectional size 65x50x25mm & 65x35x25 mm and 55x40x20 mm for shutter including safety grill on outer side made with 10 mm thick square bar having centre to centre spacing of 10cm on both longitudinal and transverse axis. Window shutter is fixed with 5mm thick poly carbonate glass of density not less than 1.20gm/cm3 including cost of 04 Nos. 100x58x1.90 mm mild steel butt hinges, 02 Nos. 125 mm mild steel handles , 04 Nos. 150x10 mm mild steel tower bolts etc complete .

Supply and fixing of Ventilator of size 0.45mx0.60m composited with mild steel ERW pipes for frames of sectional size 65x50x25mm & 65x35x25 mm and 55x40x20 mm for shutter including safety grill on outer side made with 10 mm thick square bar having centre to centre spacing of 10cm on both longitudinal and transverse axis. Window shutter is fixed with 5mm thick poly carbonate glass of density not less than 1.20gm/cm3 including cost of 02 Nos. 100x58x1.90 mm mild steel butt hinges, 125 mm mild steel handles , 02 Nos. 150x10 mm mild steel tower bolts etc complete .

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including backfilling/disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge in all kinds of soil

Earth work in excavation by manual means over areas for foundation , drains, cables, cesspits etc. including disposal of excavated earth upto 1mtr from cutting edge, disposed earth is to be leveled and neatly dressed in all kinds of soil

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof Course 50 mm thick (DPC) with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate

Centering and shuttering including strutting propping etc and removal of form work

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing unplasticized PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and fixing 15 mm PTMT bib cock of apprpved make

Providing and fixing 15 mm nominal bore angle valve (PTMT)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge Internal work-exposed on wall, including fixing the pipe with clamps at 1.00 meter spacing 15mm nominal outer dia pipes

Carriage of material by MT from Ganderbal to Dumail for an avg lead of 73 Kms

Carriage of cement by head load for a lead of 12 kms from Dumail to Lower Holy Cave.

Carriage of cement by head load for a lead of 12 kms from Dumail to Lower Holy Cave.

Carriage of sand & Bajri by head load for an average lead of 5 kms.

Carriage of metal by head load for a lead of 500 meters

Fixing corrugated G.S sheet roofing including vertical curved surface fixed with J or L hooks, bolts or self driven screws, nails etc excluding the cost of purlins, rafters and trusses and including cutting to size and shape where ever required

Dismantling roofing including ridges, hips, valleys and gutters etc and stacking material within 50 meter lead of G.S. sheet.

Dismantling roofing including ridges, hips, valleys and gutters etc and stacking material within 50 meter lead of G.S. sheet.