Comprehensive repair and maintenance of newly allotted quarters (Phase-2) in Bokaro Steel City Township, Jharkhand

Modified Estimated Cost after using Correction

Included in rate

factor on DSR 2023 on account of GST @0.973

GRAND TOTAL 13,15,07,951

GRAND TOTAL 13,15,07,951

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

1A Civil Works -DSR

Earth work in excavation by mechanical means (Hydraulic excavator)

/ manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on

plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to

1.5m,as directed by Engineer-in-Charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and

watering, lead up

to 50 m and lift up to 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up

to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding

20 cm in trenches,

plinth, sides of foundation etc., complete.

2.27 Supplying and filling in plinth with sand under floors, including cum

watering, ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings

of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up

to a distance of

50m outside the periphery of the area cleared.

2.34 Supplying chemical emulsion in sealed containers including delivery as specified. -

6 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 1800.00 251.25 4,52,255.27

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment

(excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300

mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1

cement : 2 Coarse

sand) to match the existing floor :

7 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. sqm 1500.00 331.85 4,97,769.77

Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval

including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2

coarse sand) to

the full depth of the hole :

8 2.35.4.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. nos 5000.00 46.02 2,30,114.50

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in

oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at

downward angle of 45 degree at 150 mm centre to centre and sealing the same.

2.36 Extra for levelling & neatly dressing of disposed soil completely as sqm

directed by Engineer-in-Charge.

Reinforced Concrete work for counters

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural

sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

4.1.5 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate

20 mm nominal size derived from natural sources).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15°

landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair

cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing

and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources

: 3 graded stone aggregate 20 mm nominal sizederived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for :

Shelves (Cast in situ)

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4

graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire,

5.18 including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 -

(1 cement: 3 fine sand) etc. complete, excluding plastering of the

jambs, sills and soffits.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

16 5.22A.6 position and binding all complete upto plinth level. Thermo Mechanically Treated bars of kg 100.00 115.43 11,543.19

grade Fe-500D or more

Brick work with clay flyash F.P.S. (non modular) brick of class

17 6.32.2 designation 7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:6 cum 82.50 9,734.43 8,03,090.64

(1 cement : 6 coarse sand)

6.13 Half brick masonry with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

18 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 62.50 1,202.80 75,175.20

Providing and fixing 18mm thick gang saw cut ( premoulded and prepolished) machine cut for

kitchen platforms, vanity counters, window sills, facias and similar locations of required size of

approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4

coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch

ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc.

complete at all levels.

Marble, Area of slab over 0.50 Sqm.( For Counter)

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and

20 8.4 drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. meter 10.00 608.52 6,085.19

Extra for providing opening of required size & shape for wash basin/kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone work,

21 8.5 including necessary holes for pillar taps etc. including moulding, rubbing and polishing of nos 10.00 1,047.50 10,475.03

edges etc. complete

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,

22 8.31 over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey sqm 50.00 1,357.09 67,854.34

cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash fastener shall be paid for separately).

23 9.1.1 Second class teak wood Cum 0.50 1,52,999.06 76,499.53

9.7.7 Float glass panes -

25 9.7.7.1 4 mm thick glass pane (weight not less than 10 kg/sqm). sqm 500.00 2,399.40 11,99,699.27

26 9.7.7.2 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). sqm 50.00 2,783.26 1,39,163.08

Providing and fixing glazed shutters for doors, windows and clerestory windows using

4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked

M.S. pressed butt hinges bright finished of required size with necessary screws.

9.9.1 Second class teak wood -

9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative

type, core of block board construction with frame of 1st class hard wood and well matched teak

3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

9.20.3 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS

: 3818 marked with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and well

9.21 matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on -

both faces of shutters:

9.21.2 30 mm thick including ISI marked Stainless Steel butt hinges with sqm

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges

30 9.23 of flush door shutters (over all area of Sqm 625.00 494.85 3,09,283.25

door shutter to be measured).

9.48 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S.

flats, square or round bars etc. including -

priming coat with approved steel primer all complete.

31 9.48.1 Fixed to steel windows by welding kg 150.00 234.50 35,175.41

32 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. kg 0.00 255.11 -

9.51 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows

using wire gauge with average width of aperture 1.4 mm in both directions with wire of

dia 0.63 mm all

33 9.51.1 With second class teak wood beading 62X19 mm sqm 30.00 1,400.33 42,009.81

34 9.51.2 With 12 mm mild steel U beading sqm 205.00 1,005.23 2,06,071.28

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block

35 9.53 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm Each 2670.00 244.94 6,53,984.87

9.55 Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges

bright finished with necessary screws etc. complete :

Providing and fixing oxidised M.S. hasp and staple (safety type)

9.67 conforming to IS : 363 with necessary screws etc. complete (Copper oxidised as per IS 1378) -

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc.

complete (Copper oxidised as per IS 1378)

43 9.68.1 300 mm weighing not less than 330 grams No 4235.00 72.14 3,05,505.36

44 9.68.2 250 mm weighing not less than 280 grams Nos 0.00 65.34 -

Providing and fixing chromium plated brass 100 mm mortice latch

45 9.88 and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. Nos 10.00 1,068.53 10,685.34

9.91 Providing and fixing chromium plated brass 50 mm cupboard or Nos

wardrobe knobs with nuts complete.

9.92 Providing and fixing chromium plated brass handles with necessary

screws etc. complete:

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less

than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade

screws etc. complete :

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less

than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade

screws etc. complete :

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not

less than grade AC 10 as per IS : 1868) transparent or dyed of required colour and

shade, with necessary

screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles of approved make anodized (anodic coating not less

than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade

screws etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating

not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade

screws etc. complete.

56 9.101.1 Single rubber stopper Each 835.00 42.38 35,390.54

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an

overall dimension as below (tolerance

±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with

galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side

vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1

mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per

manufacturer ’s specification and

direction of Engineer in-charge

57 9.117.1 Extruded section profile size 48x40 mm Rmt 1800.00 289.20 5,20,551.11

9.118 Providing and fixing to existing door frames. -

24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of

size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles

and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size

75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter

reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall

thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2

Providing and fixing factory made Fiberglass Reinforced Plastic (F.R.P.) Chhajja 4mm thick

of required colour size and design made of Resin Transfer moulding (RTM)Machine technology,

resulting in void free compact laminate in single piece, having smooth gradual slope curvature

for easy drainage of water and duly reinforced by 2 nos vertically and 1 no horizontally mm

thick MS flat with 12mm inbuilt hole for grouting on the existing wallalongwith 50mm

flangesduly inserted and sealed in the wall completein one single piece casted

monolithically, including all necessary fittings. The FRP chhajja should be manufactured using

unsaturated polyester resin as per IS: 6746, duly reinforced with fiber glass chopped strand

9.147A mash (CSM)

Providing andas perfactory

fixing IS:11551 complete

made with protective

uPVC glazed/wire mesh Gel coat U/V coating

windows/doors on top

comprising for free

uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles

having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series

R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with

galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC

extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate

dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with

countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to

finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless

steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing

hardware and drainage of water etc.

After fixing frame the gap between frame and adjacent finished wall shall be filled with weather

proof silicon sealant over backer rod pf approved size and quality, all complete as per approved

drawing conforming to CPWD specification & direction of Engineer-in-Charge.

Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved

by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit

with / without high performance coatings as per design requirements and conforming to IS: 3548

& IS:16231 shall be paid separately.

Note:- Structural design proof checked from a Government

Engineering Institute, to be provided by the manufacturer for:

(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 -

(ii) Sites with structure height more than 20m for all wind speeds. -

Two track two panels sliding window with Aluminium channel for

roller track, wool pile, nylon rollers with SS 304 body.

Using R2 series with frame (40mm & above) x (40mm & above) & sash (25mm & above) x (50mm

60 9.147.A1.1 & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 meter) sqm 5.00 8,882.26 44,411.30

Ventilator Casement window single panel with or without fixed panel

9.147.D1 with S S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) -

powder coated handles.

Using R1 series with frame (33mm & above ) x (35mm & above) & sash /mullion (33mm & above)

Casement window single panel with S.S. 304 friction hinges as per

9.147.E1 size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. -

Using R2 series with frame (39mm & above) x (39mm & above) & sash (39mm & above) x (60mm

& above). (Height upto 1.2 meter)

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make

with necessary screws etc all complete.

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,

square or round bars etc. including priming coat with approved steel primer all complete.

66 9.48.2 MS Grills for windows Kg 100.00 255.11 25,510.60

Fixed to openings

Fixing standard steel glazed doors, windows and ventilators in walls, including fixing of float

glass panes with glazing clips and special metalsash putty of approved make, or metal

10.10 beading with screws, (only steel windows, glass panes cut to size and glazing clips or metal -

beading with screws, shall be supplied by department free of cost.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

67 10.10.1 block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm kg 300.00 88.25 26,473.87

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections,

joints mitred and welded, including fixing of necessary butt hinges and screws and applying a

priming coat of

approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

68 10.13.1 block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm kg 50.00 151.66 7,583.08

Welding by gas or electric plant including transportation of plant at

site etc. complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels,

plates etc., including welding, grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel nuts and bolts complete,

i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel

70 10.28 bolts etc., of required size, on the top of the floor or the side of waist slab with Kg 100.00 826.70 82,669.97

suitable arrangement as per approval of Engineer-incharge, (for payment purpose only

weight of stainless steel members shall be considered excluding fixing accessories such as nuts,

bolts, fasteners etc.).

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar,

11.1 including filling the joints with same mortar, -

with common burnt clay non modular bricks:

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished

with a floating coat of neat cement, including cement slurry, but excluding the cost of

nosing of steps etc.

72 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 2735.00 657.38 17,97,929.54

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with

neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and

11.20 cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 -

73 11.20.1 Light shade pigment using white cement. sqm 100.00 1,500.56 1,50,056.06

74 11.20.2 Medium shade pigment using 50% white cement 50% Grey cement. sqm 100.00 1,421.73 1,42,173.30

75 11.20.3 Dark shade pigment using ordinary cement. sqm 100.00 1,198.20 1,19,820.09

76 11.20.4 Ordinary cement without any pigment. sqm 100.00 1,130.61 1,13,061.14

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness

to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make,

in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement

Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar

1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently

Double charge vitrified tile polished finish of size -

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for

expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with

81 12.42.4.2 seal ring conforming to IS Each 590.00 236.91 1,39,777.43

: 5382, leaving 10 mm gap for thermal expansion:Single tee with door

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with

82 12.42.5.2 seal ring conforming to IS Each 345.00 160.92 55,517.26

: 5382, leaving 10 mm gap for thermal expansion:Bend 87.5° 110 mm

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for

unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with

seal ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion:Shoe (Plain) 110 mm Shoe

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal

of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120

grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of

the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of

25 microns minimum to avoid scratches during transportation and should be supplied in

single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using

self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any

pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses

and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total

coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating

thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade,

5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns

using self drilling/ self tapping

screws complete:

86 12.51.2 Flashings/ Aprons.( Upto 600 mm) meter 5.00 519.74 2,598.69

87 12.51.3 North light curves meter 5.00 584.49 2,922.45

88 12.51.4 Barge board (Upto 300 mm) meter 5.00 483.24 2,416.20

89 12.51.6 Gutter (600 mm over all girth) meter 5.00 1,406.05 7,030.27

13.1 12 mm cement plaster of mix : -

13.2 15 mm cement plaster on the rough side of single or half brick wall of mix : -

13.16 6 mm cement plaster of mix : -

93 13.18 Neat cement punning sqm 50.00 85.57 4,278.52

Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel

or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh

13.19 plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) and -

top layer 10 mm cement plaster 1:3 (1 cement: 3 fine sand) mixed with 10% finely

grounded hydrated lime by volume of cement.

94 13.19.1 Ordinary cement finish using ordinary cement sqm 4000.00 948.93 37,95,711.92

13.45 Finishing walls with textured exterior paint of required shade : -

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of

exterior primer applied @2.20kg/10 sqm.

13.50 Applying priming coat : -

With ready mixed aluminium primer of approved brand and

manufacture on resinous wood and plywood.

With ready mixed red oxide zinc chromate primer of approved brand

and manufacture on steel galvanised iron/steel works

Providing and applying white cement based putty 1mm on plaster

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture,

13.83 including applying additional coats wherever required to achieve even shade and -

Applying priming coats with primer of approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC

content less than 50 grams/litre.

Removing white or colour wash by scrapping and sand papering and

101 13.88 preparing the surface smooth including necessary repairs to scratches etc. complete sqm 145680.71 21.14 30,79,460.83

Painting with synthetic enamel paint of approved brand and manufacture of required colour to

102 13.99.1 give an even shade : One or more sqm 37387.91 110.03 41,13,673.91

coats on old work

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and

103 14.1.1. preparing and plastering the surface of the walls complete, including disposal of rubbish to the sqm 1000.00 585.88 5,85,882.22

dumping ground, all complete as per direction of Engineer in-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand)

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting

masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm

with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal

14.2 size), painting two coats of approved wood preservative to sides of chowkhats and making good -

the damages to walls and floors as required complete, including disposal of rubbish to the

dumping ground, all complete as per directions of Engineer-In-Charge.

Providing and fixing bright finished brass casement window fasteners

106 14.73 or peg stays to windows/ ventilators with necessary welding and machine screws etc. kg 10.00 596.37 5,963.71

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including

cutting the patch in proper shape, raking out joints and preparing plastering the wall

surface with white cement based polymer modified self curing mortar, including

disposal of rubbish, all complete as per the direction of Engineer-In-

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete

108 14.82 as per directions of Engineer-in each 545.00 143.53 78,222.34

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres

109 14.84 lead) as per direction of Engineer in-Charge. meter 6540.00 3.48 22,749.23

(a) Internal Work- Exposed on wall

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired

110 14.85 door shutters to existing door frames, including replacement of hinges with screws, etc. as Each 4000.00 459.27 18,37,062.92

required, all complete as per the direction of the Engineer-in-charge

Dismantling works

Demolishing cement concrete manually/ by mechanical means including disposal of

111 15.2.2 material within 50 metres lead as per direction cum 247.50 1,609.30 3,98,302.51

of Engineer - in - charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars

112 15.3 and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- cum 20.00 3,800.90 76,018.06

Demolishing brick work manually/ by mechanical means including stacking of serviceable

material and disposal of unserviceable material within 50 metres lead as per direction of

Dismantling doors, windows and clerestory windows (steel or wood) shutter including

114 15.12.1 chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead each 1185.00 393.01 4,65,721.78

Of area 3 sq. metres and below.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within

For thickness of tiles 10 mm to 25 mm

Dismantling barbed wire or flexible wire rope in fencing including

making rolls and stacking within 50 metres lead

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful

117 15.52 materials near the site and disposal of each 520.00 119.93 62,362.10

unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including

118 15.56 disposal of rubbish to the dumping sqm 15231.03 58.49 8,90,892.07

ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste

materials by mechanical means, including loading, transporting, unloading to approved

119 15.60 municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial Cum 525.00 282.51 1,48,315.48

lead, for all leads including all lifts involved.

16.15 Supplying at site : -

R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded

stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required

as per direction of Engineer-in-charge (cost of earth works in excavation, concrete works in

foundation to be paid separately).

Welded steel wire fabric of required width having rectangular mesh painted with two or more

121 16.15.2 coats of enamel paint of approved shade over a coat of primer (Priming & Painting to be paid for Kg 8000.00 84.50 6,76,001.48

16.17 Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every

15th post, last but one end post and corner post shall be strutted on both sides and end post one

side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per

100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs

or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts,

earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total

length of barbed wire used.

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

16.18 Fencing with angle iron post placed at required distance embedded in cement concrete blocks,

every 15th post, last but one end post and corner post shall be strutted on both sides and end

post on one side only and provided with horizontal lines and two diagonals interwoven with

horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts -

fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work

and concrete work to be paid for separately). Payment to be made per metre cost of total length

of barbed wire used.

16.19 Supplying at site Angle iron post & strut of required size including bottom to be split and bent at Kg

124 right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. 800.00 134.59 1,07,672.18

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm

dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto

3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9

horizontal R.B.T. reinforced barbed wire, stud tied with

125 16.53 G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire meter 650.00 402.22 2,61,442.18

tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed

tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm

with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be

paid separately)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of

M -30 grade made by block making machine with strong vibratory compaction, of approved

126 16.68 size, design & shape, laid in required colour and pattern over and including 50mm thick sqm 1500.00 1,040.33 15,60,497.40

compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the

direction of Engineer-in-charge.

Aluminium works -

Providing and fixing aluminium work for doors, windows, ventilators and partitions with

extruded built up standard tubular sections/appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with

fixing clips, or with expansion hold fasteners including necessary filling up of gaps at

junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections

21.1 shall be smooth, rust free, straight, mitred and jointed echanically wherever required including -

cleat angle, Aluminium snap beading for glazing / paneling,

C.P. brass / stainless steel screws, all complete as per architectural drawings and the

directions of Engineer-in-charge. Glazing and paneling to be paid for separately) :

21.1.1 For fixed portion. -

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever required including the cost of EPDM

rubber / neoprene

gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions

etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and

129 21.3 the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic sqm 808.84 1,259.53 10,18,757.47

With float glass panes of 4.0 mm thickness

Providing and laying water proofing treatment in sunken portion of

22.5 WCs, bathroom etc., by applying cement slurry mixed with water proofing cement -

compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound

@ 0.253 kg/ sqm. This layer will be -

allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement

compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with

water curing for 48

(The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Repair with New Technologies

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel

and/ or by standard power driven percussion type or of approved make including tapering of all

edges, making square shoulders of cavities including cleaning the exposed concrete surface and

reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as

per direction of Engineer-In-Charge. 75mm average thickness

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel

surface by using alkaline chemical rust remover of approved make with paint brush and

26.29 removing loose particles after 24 hours of its application with wire brush and thoroughly washing -

with water and allowing it to dry, all complete as

per direction of Engineer-In-Charge.

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as

26.31 per specifications and direction of Engineer -

In-charge complete in all respect.

Epoxy bonding adhesive having coverage 2.20 sqm/kg

of approved make

1A Total civil works - ₹ 11,14,89,521.66

2A Sanitary & Plumbing

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing and fixing water closet squatting pan (Indian type W.C.pan

) with 100 mm sand cast Iron P or S trap, 10 litre low level white

17.1 P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) -

conforming to IS : 7231, with all fittings and fixtures complete, including cutting and

making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan)

with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever),

conforming to IS : 7231, with all fittings andfixtures complete, including cutting and

making good the walls

and floors wherever required :

136 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Nos 112.00 6,973.59 7,81,042.43

Providing and fixing white vitreous china pedestal for wash basin

completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the

direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets

and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making

the walls wherever required:

17.10.1 Kitchen sink with drain board -

17.10.2 Kitchen sink without drain board -

Providing and fixing white vitreous china water closet squatting pan

(Indian type) :

141 17.13.2 Orissa pattern W.C. pan of size 580x440 mm Nos 62.50 3,391.83 2,11,989.64

Providing and fixing white vitreous china pedestal type (European

type/ wash down type) water closet pan.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S.

143 17.16A triangular plate to Eureopean type W.C. of Nos 5.00 373.70 1,868.48

quality and make as approved by Engineer - in - charge.

Providing and fixing a pair of white vitreous china foot rests of

standard pattern for squatting pan water closet :

Providing and fixing P.V.C. low level flushing cistern with manually

17.18 controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures -

Providing and fixing solid plastic seat with lid for pedestal type W.C.

146 17.20.1 White solid plastic seat with lid Nos 125.00 732.99 91,624.37

Providing and fixing white vitreous china wash basin including making

all connections but excluding the cost of fittings :

147 17.25.1 Flat back wash basin of size 630x450 mm. Nos 125.00 1,433.88 1,79,235.11

148 17.25.2 Flat back wash basin of size 550x400 mm. Nos 470.00 1,062.38 4,99,318.50

149 17.25.3 Angle back wash basin of size 600x480 mm. Nos 5.00 1,433.88 7,169.40

150 17.25.4 Angle back wash basin of size 400x400mm. Nos 5.00 931.16 4,655.81

151 17.25.5 Flat back wash basin of size 450x300 mm. Nos 5.00 671.08 3,355.39

Providing and fixing P.V.C. waste pipe for sink or wash basin including

P.V.C. waste fittings complete.

17.28.2 Flexible pipe -

153 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Nos 5.00 56.99 284.97

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved

quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P.

brass screws and washers

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size

with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised

aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm

long screws, rawl

plugs etc., complete.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or

157 17.60.1.2 without vent arm complete, including cost of cutting and making good the walls and floors :100 Each 486.00 1,801.90 8,75,725.13

mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS: 1729

Providing and fixing PTMT Waste Coupling for wash basin and sink, of

approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62 mm breadth

weighing not less than 45 gms.

17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink. -

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail

pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum

water seal, weighing

not less than 260 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm

distance from wall of standard shape with bracket of the same materials with snap fittings of

approved quality

and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with

minimum distances of 37 mm from wall face with concealed fittings arrangement of

approved quality and colour,

weighing not less than 88 gms.

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP

17.73 brass screws with concealed fittings -

arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and

effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot

& cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of

18.8 pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints -

complete as per direction of Engineer in Charge : External work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot

& cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of

18.9 pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints -

complete as per direction of Engineer in Charge : External work

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Providing and fixing uplasticised PVC connection pipe with brass

18.21.1 30 cm length -

18.21.2 45 cm length -

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking arrangement and making necessary holes for

inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931:

18.54 Providing and fixing PTMT bib cock of approved quality and colour. -

178 18.54.3 15 mm nominal bore, 165 mm long. Weighing not less than 110 gms. Each 1335.00 189.28 2,52,692.21

18.55 Providing and fixing PTMT stop cock of approved quality and colour. -

179 18.55.1 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. Each 420.00 126.83 53,268.83

18.56 Providing and fixing PTMT pillar cock of approved quality and colour . -

15mm nominal bore, 125 mm long foam flow. Weighing not less than

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards

181 18.51.1 and weighing not less than 690 gms. Each 75.00 855.12 64,133.71

15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and

geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet,

150 mm diameter

Dismantling old C.I. pipes including excavation and refilling trenches after taking out the pipes,

breaking lead caulked joints, melting of lead and making into blocks including stacking of

pipes at site lead upto 50 metre:

100 mm diameter C.I. pipe

2A Total Sanitary & plumbing works 1,65,45,684.59

1B Non-schedule - Civil

Removal and cleaning of one or more vegetation/ plants from walls roofs, chajja etc.up to 4 sqm

area, chemically treatment of surface to prevent further growth, and making good the

185 MR surface by plaster , grouting ,waterproofing , etc. as the case may be including necessary nos 300.00 704.28 2,11,284.00

scaffolding staging etc.

1B Total Non-schedule -Civil 2,11,284.00

2B Non Schedule Items- Plumbing

Supply, installation , testing commissioning of PP Mineral filled low noise Soil & Waste system

as per EN 12056, with density 1.9 g/cm3. PP mineral(Astolan) filled Low noise system should has

a fire classification DIN 4102-B2/EN13501 . Product should have a chemical resistance of pH 2-12

and is a complete sound protection system according to DIN 4109. including with push fit

rubber ring sockets all necessary fittings and specials such as Bends, junctions, offsets & vent

cowl. Fixing at wall/ceiling level supported by rubber line bracket & hangers etc. duly epoxy -

coated. Cutting, chases/holes in floors / walls / slab.Compliant with LABC. Weight mass per unit

area of DN100MM should not be less than 110.07kg/m3. sound levels of not more than 15dBA as

per EN 14366 at a flow rate of 4 l/s.including all core cut ,chases

,cutting making holes in all wall and floor as required complete in all respect.

Digitally signed by PRIYA

SL No. Description of Work Unit BOQ Qty. RATE Boq Amount

Providing Fixing straight /offset type single body push fit type WC pan connector with factory

supplied spring loaded seal guard with integral single mould sealing fins made of flexible

190 NS EVA body, including bush/adaptor as supplied with the pan connector (if Each 10.00 800.00 8,000.00

Providing and fixing floor drain (FD) with 50mm/40mm outlet and one 40mm inlet for

191 NS waste, with SS grating (adjustable height), Each 10.00 1,655.00 16,550.00

having 50mm water seal and in-built NRV

Providing and fixing PP/UPVC trap of self cleansing design with screwed down or hinged grating

with or without vent arm complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet

192 NS Sand cast iron S&S as per IS: 3989 Each 10.00 1,655.00 16,550.00

Providing and fixing PP/ UPVC grating with Cockroach proof strainer of approved design

including setting in floor with cement motor to match with floor finish as per architect

suitable for waster and FT.

Providing and fixing PP/UPVC brass grating with frame of approved design including setting in

floor with cement motor to

match with floor finish as per architect requirement.

Providing and fixing PP/UPVC extention piece for 100 mm dia floor trap formed out of main pipe

with multiple side inlets, suitable for various dia pipes including all fixtures as required complete

as per drawing approved sample and direction of engineer in charge.

Providing and fixing Jaguar make ARI-39041 or equivalent Two way bib cock with wall flange as

per direction of E/I

Providing and fixing Jaguar Make COP-057PM or equivalent C.P. angular valve as per

direction of E/I

Providing and fixing ESSCO make MQT-514 FKN or equivalent Concealed Stop cock

20mm as per direction of E/I

Providing and fixing Jaguar make COP-273PM or equivalent Short body bib cock as per

direction of E/I

Providing and fixing Jaguar make OHS-1989 or equivalent Overhead shower as per direction of

Providing and fixing Jaguar make ALD-573 B138 or equivalent Health Faucet as per

direction of E/I

Providing and fixing Jaguar make ACN-1111SM Towel rail or equivalent 600 mm long as

per direction of E/I

Providing and fixing Jaguar make AHS-1551 or equivalent Toilet paper Holder as per

direction of E/I

Providing and fixing Jaguar make CAN-1161N or equivalent Double coat hook as per direction

Providing and fixing Jaguar make SDR-WHT-DJ0010F or equivalent Soap Container as per

direction of E/I

Providing and fixing Jaguar make CNS-WHT-705 or equivalent Under Counter basin as per

direction of E/I

207 NS Providing and fixing Jaguar or equivalent make Pillar cock as per direction of E/I Each 224.00 1,928.56 4,31,997.44

Providing and fixing Jaguar ESSCO or equivalent Waste coupling as per direction of E/I

2B Total Amount 32,61,460.65

2B Total Amount 32,61,460.65

Total Amount DSR (1A+2A) 12,80,35,206

Total Amount DSR (1A+2A) 12,80,35,206

After adding cost index @ 10% as per CPWD office memorandum 34(1)/cost

index/ ADG (patna)/ 2024/685 dated 11.12.2024 Included in above Rates

Modified Estimated Cost after using Correction factor on DSR 2023 on

account of GST @0.973 Included in above Rates

Total Amount Non-DSR (1B+2B) 34,72,745

Total Amount Non-DSR (1B+2B) 34,72,745

GRAND TOTAL - 13,15,07,951

GRAND TOTAL - 13,15,07,951

Digitally signed by PRIYA