Supply, erection, installation, testing and commissioning of material/ equipment for the various activities of DEVELOPMENT OF DISTRIBUTION INFRASTRUCTURE AT Karauli circle of Jaipur Discom of Rajasthan State under RDSS on Turnkey basis.

Amount

(A)Bifurcation of 33 KV Line due to overloading

33 KV Bay

Outdoor 36 KV O/D VCB KIOSK complete with accessories

Overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification including PG clamp

M.S. Flat 50 X 6 mm (Galvanized) for earthing

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

GO double break without EB Isolator for existing bracket complete in all respect as required including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

Horn gap sets for existing brackets in all respect as required including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 NOS

33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors for the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works.

PCC Poles

PCC Ploe 9.0 mtrs long.(400 Kg.)

45 KN Composite polymer insulators for 33 KV on brackets complete including all acessories like hardware fitting etc.

Porcelain 33KV Pin Insulator with Pins on pole complete in all respect

PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

33 kV Danger plate of size 200 X 250 mm complete in all respect

33 KV UNDERGROUND CABLE

PCC Poles

PCC Pole 9 mtrs long (400 KG)

12.8 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING With 03 NOS. of 33 KV Channel Cross Arm(100x50 mm) with 48 NOS. of Nut & Bolts(M 16x45) (Galvanized) Weight(580.827 kg)

UNDERGROUND CABLE FOR WORKING VOLTAGE OF 33KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED

Under ground Cable of Size 3X300 SQ.MM for 33 KV

G.I. PIPE OF 150 MM DIAMETER, B-CLASS (IS:1239 MARK)

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE END TERMINATION KIT/ST JOINT FOR 33 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE

XLPE 3X300 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X300 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X300 SQ.MM H.S.S.T. JOINT

BACK CLAMP AND STAY CLAMP FOR CROSS ARMS, STAY, EARTH AND GUARDING BRACKET OF MS FLAT . (Galvanized as per IS)

HD GALVANISED M.S.ROD TYPE EARTHING SET MADE UP OF M.S.ROD 20 MM DIA. 3 METER LONG ALONGWITH EARTHING CLAMP & 8 SWG EARTH WIRE 15 METER LONG (FOR EARTHING OF 33 KV LINE)

33 KV OVERHEAD LINE WORK

PCC Poles

PCC Pole 9 mtrs long (400 KG)

12.8 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING With 03 NOS. of 33 KV Channel Cross Arm(100x50 mm) with 48 NOS. of Nut & Bolts(M 16x45) (Galvanized) Weight(580.827 kg)

33 KV 'V' cross arms with TOP Hamper made of MS Angle75X75X6 mm with clamp of size 50X10 mm,earth clamp50X6 mm with nuts, bolts & Washers as per latest specification and drawings adopted & approved by Nigam (Galvanized as per IS)

A SET OF 4 NOS. 33KV 'V' CROSS ARMS(CHAKRI) MADE OF M.S. CHANNEL 100X50 MM ISMC [9.56 KG PER MTRS.] ON THE EXISTING LATTICE TOWER WITH BRACING OF M.S. FLAT ( 50 X 10 MM) INCLUDING NUT AND BOLTS ETC. WEIGHT OF THE ITEM WILL BE AS PER DRAWING

A set of 4 NOS. 33 KV 'V' cross arms (Chakri) made of M.S.Angle 75x75x6 mm with bracing of M.S.Flat 50 x 10 mm including all necessary clamps, nuts & bolts etc. (Galvanized as per IS)

M.S. CHANNEL [CUT POINT ] 100X50 MM ISMC [9.56 KG. PER MTR] 2X1.8 MTRS LONG WITH PILOT PATTI 50X6MM [2.36 Kg. per mtr] THICK AND NECESSARY NUTS AND BOLTS ETC. WEIGHT OF THE CUT POINT CHANNEL WILL BE AS PER DRAWING APPX. 39.00 Kg. (Galvanized as per IS).

33 KV DOUBLE POLE LINE STRUCTURE SET FOR CUT POINT COMPLETE ON EXISTING POLES IN ALL RESPECT WITH CLAMP, NUT & BOLTS AS REQURIED MADE FROM M.S.CHANNEL 100 X 50 X ISMC ( 9.56 KG. PER MTR.) ISA M.S.ANGLE 65 X 65 X 6 MM, M.S.ANGLE 50 X 50 X 6 MM AND M.S.FLAT 50 X 6 MM (Galvanized as per IS)

33 KV PORCELAIN PIN INSULATOR WITH PIN ON EXISTING POLE COMPLETE INCLUDING ALL ACCESSSORIES LIKE HARDWARE FITTING AND NUTS AND BOLTS ETC.

3 NO. 11 KV B&S TYPE 120 KN PORCELAIN DISC INSULATOR ON COMPLETE LINE DP INCLUDING ALL ACCESSORIES LIKE HARDWARE FITTING 1 NO. AND NUTS AND BOLTS ETC.

GS Stay set complete with 20 mm dia., 2.4 meter long stay rod with zinc coated steel Anchor Plate of size 300x300x4 mm with square hole of size 18x18 mm at centre IN GROUND AND GS STAY WIRE 7/8 MM TIGHTENED THROUGH 33 KV STAY INSULATOR INCLUDING CLAMPS

GS WIRE NO.6 SWG HOT DIP GALVANIZED [5.0 MM DIA] COMPLETE IN ALL RESPECTS WITH BINDING WIRE EACH POLE WITH TOP HAMPER & CROSS ARM (WITH 1.1 M WIRE).

Overhead ACSR 100 Sq.mm. Dog conductor on existing cross arms complete in all respect. (Cost of material includes the sag and jumpering)

ACSR Dog conductor

PG Clamps for Dog conductor

HD GALVANISED M.S.ROD TYPE EARTHING SET MADE UP OF M.S.ROD 20 MM DIA. 3 METER LONG ALONGWITH EARTHING CLAMP & 8 SWG EARTH WIRE 15 METER LONG (FOR EARTHING OF 33 KV LINE) .

CEMENT CONCERETING M.10 GRADE [ 1:3:6 ONE CEMENT THREE COARSE SAND,6 GRADED STONE AGGREGATE] INCLDUING CURING COMPACTION ETC. COMPLETE USING STONE AGGREGATE 20 MM NOMINAL SIZE.IN FOUNDATION AND PLINTH.

BACK CLAMP AND STAY CLAMP FOR CROSS ARMS, STAY, EARTH AND GUARDING BRACKET OF MS FLAT

33KV DANGER PLATE ON THE TOWERS/ POLES COMPLETE IN ALL RESPECT AS PER DRAWING.

ISA M.S. ANGLE 50X50X6 MM (Galvanized as per IS)

ISA M.S. ANGLE 65X65X6 MM (Galvanized as per IS)

ISA M.S. Flat 50X 6 (Galvanized as per IS)

ISA M.S. Channel 100X50X6 (Galvanized as per IS)

(B)Bifurcation of 11 KV Line due to oveloading

11 KV Bay

Outdoor 11 KV O/D VCB KIOSK complete with accessories including use of special tools

Control Cable of size 12C X 2.5 SQ.MM. 1100 Volts PVC Insulated including supply of ferrules

Overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing

M.S. Flat 50 X 6 mm (Galvanized) for earthing

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Metering points on 11 KV outgoing feeder at 33/11 KV S/S. (including following cost of (a) and (b) )

(a) Mounting structure (Galvanized)

(b) The requisite steel members will be supplied by contractor including the hardware.Contractor shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor.

Installation of Metering equipments:

11KV CT PT Set(200/5 Amp.)

MIP meter boxThe meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

PCC Poles

PCC POLE 9.0 mtrs long.(200 Kg.)

45KN. porcelain disc.insulators for 11 KV ( each unit consisting of disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

11 kV Danger plate of size 200 X 250 mm complete in all respect

M.S Channel 100x50x6mm

M.S Angle 65x65x6mm

11 KV UnderGround Cable Work

PCCPoles

9 mtrs long (200 KG)

UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED

Under ground Cable of Size 3X185 SQ.MM for 11 KV

G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK)

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE

XLPE 3X185 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

Galvanised M.S.Rod type earthing set (including nuts & bolts) made up of M.S.Rod 20 mm dia. 3 meter long alongwith earthing clamp & 8 SWG earth wire 15 meter long (for earthing of 11 KV line)

11 KV Over Head Line Work

PCC Poles

PCC Pole 9 mtrs long (200 KG)

11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING.

11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Overhead steel cored aluminum ACSR Rabbit conductor in all respect

11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986

8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

11 KV Danger plate of size 200 X 250 mm complete in all respect

1.4 Mtr Channel bracket with clamp

(C)HVDS works

11 KV Overhead Line-1-Phase

PCC Poles

PCC Pole 9 mtrs long (200 KG)

Overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor

11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

LT Porcelain Pin insulators with pins

PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

11 KV Danger plate of size 200 X 250 mm complete in all respect

1.4 Mtr Channel bracket with clamp

11 KV Overhead Line-3-Phase

PCC Poles

PCC Pole 9 mtrs long (200 KG)

11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING.

11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Overhead steel cored aluminum ACSR Rabbit conductor in all respect

11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

11 KV Danger plate of size 200 X 250 mm complete in all respect

1.4 Mtr Channel bracket with clamp

11 KV Underground Cable

PCC Poles

PCC Pole 9 mtrs long (200 KG)

UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED

Under ground Cable of Size 3X185 SQ.MM for 11 KV

G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK)

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE

XLPE 3X185 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

HD Galvanised M.S.Rod type earthing set (including nuts & bolts) made up of M.S.Rod 20 mm dia. 3 meter long alongwith earthing clamp & 8 SWG earth wire 15 meter long (for earthing of 11 KV line)

1-Phase DTR

PCC Poles

PCC Pole 9 mtrs long (400 KG)

6.35KV/240 V aluminium wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming

M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

6.35/0.24 KV substation structure for 5 KVA complete (galvanized as per IS) complete in all respect made of MS Channel, MS angle and MS flat etc. including nut ,bolt,flat and spring washer (as per latest specification and drawing adopted & approved by NIGAM) (36.054 Kg. + 2 Kg. approx.)

6.35/0.24 KV substation structure for 5 KVA complete (galvanized as per IS) complete in all respect made of MS Channel, MS angle and MS flat etc. including nut ,bolt,flat and spring washer (as per latest specification and drawing adopted & approved by NIGAM) (36.054 Kg. + 2 Kg. approx.)

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

11 KV 100 Amp. Drop out cum isolator with 5.0 Amp. fuse & 12 KV post insulators including nut, bolt & washers as required as per technical specifications, approved drawings and scope of work.

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

Danger plate of size 200 X 250 mm complete in all respect

PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

3-Phase DTR

PCC Poles

PCC Ploe 9.0 mtrs long.(400 Kg.)

XLPE Insulated ACSR Rabbit (For HT)

LT XLPE Cable

Size 4CX70 SQ. mm

Size 4CX185 SQ. mm

Size 4CX120 SQ. mm

11 /0.4 KV Al/Cu wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

25 KVA (Aluminium)

40 KVA (Aluminium)

63 KVA (Aluminium)

100 KVA (Aluminium)

M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

LT Supply Pillar Box of 200 Amp. capacity as per specification of Nigam .

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11/0.4 KV SubStation structure set on existing poles in all respect with clamps made from M.S. channel 100x50 X6 mm and 75x40 mm, M.S. angle 50x50x6 and M.S. flat 50x6 mm and 50x8 mm weight(147.3 kgs.) Approx (All galvanized as per relevant IS)

Horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

LIGHTENING ARRESTOR ( FEEDER TYPE) ON ERECTED STRUCTURE / SUPPORT ( SET OF 3 NOS. )

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

Danger plate of size 200 X 250 mm complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

(D) Cabling Works in Theft Prone Area

LT Ariel Bunch Cable

PCC Poles

PCC Pole 9 mtrs long (200 KG)

Overhead ABC(Aerial bunched cable) with Bare Messenger

1C X25 +1CX25 sqmm

3C X25 +1CX25 sqmm

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Dead end (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

Suspension (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

LT insulation piercing connectors NFC Type A (main to tap) (main 16-50 mm2, Tap off 2.5-16 mm2)

LT insulation piercing connectors NFC type B ( main to main) (size 16-50 mm2)

Spring loaded box (1 phase)

Spring loaded box (3 phase)

LT Underground Cable

4 Core LT XLPE insulated PVC sheathed armoured Cable

Size 4CX70 SQ. mm

Size 4CX120 SQ. mm

Size 4CX185 SQ. mm

Size 4CX300 SQ. mm

LT DISTRIBUTION BOX AS PER SPECIFICATION OF NIGAM.

100 AMP LT DISTRIBUTION BOX

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

LT Armoured Service Cable

2CX4 Sq MM

4CX16 Sq MM

(E)Segregation of 11 KV Ag-Non Ag Feeders

11 KV Bay

Outdoor 11 KV O/D VCB KIOSK complete with accessories including use of special tools

Control Cable of size 4 X 4 SQ.MM. 1100 Volts PVC Insulated including supplyof ferrules

Control Cable of size 12C X 2.5 SQ.MM. 1100 Volts PVC Insulated including supply of ferrules

Overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing

M.S. Flat 50 X 6 mm (Galvanized) for earthing

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

Metering points on 11 KV outgoing feeder at 33/11 KV S/S. (including following cost of (a) and (b) )

(a) Mounting structure (Galvanized)

(b) The requisite steel members will be supplied by contractor including the hardware.Contractor shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor.

Installation of Metering equipments:

11KV CT PT Set(200/5 Amp.)

MIP meter box.The meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

PCC Poles

PCC Pole 9 mtrs long (200 KG)

45KN. porcelain disc.insulators for 11 KV ( each unit consisting of disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

11 KV Danger plate of size 200 X 250 mm complete in all respect

M.S Channel 100x50x6mm

M.S Angle 65x65x6mm

11 KV UnderGround Cable Work

PCCPoles

PCC Pole 9 mtrs long (200 KG)

UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED

Under ground Cable of Size 3X185 SQ.MM for 11 KV

G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK)

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE

XLPE 3X185 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

HD Galvanised M.S.Rod type earthing set (including nuts & bolts) made up of M.S.Rod 20 mm dia. 3 meter long alongwith earthing clamp & 8 SWG earth wire 15 meter long (for earthing of 11 KV line)

Double break without EB Isolator on existing bracket complete in all respect as required including hardware nut, bolts & washer etc.

11KV (with 9 x 12 KV Post Insulator ) 400 Amp. - as per latest specification, design & drawing approved by the NIGAM

11 KV Over Head Line Work

PCC Poles

PCC Pole 9 mtrs long (200 KG)

11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING.

11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps nut and bolts as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm weight(92.969 kgs.) Approx

Overhead steel cored aluminum ACSR Rabbit conductor in all respect

11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

11 KV Danger plate of size 200 X 250 mm complete in all respect

1.4 Mtr Channel bracket with clamp

3-Phase DTR

PCC Poles

PCC Ploe 9.0 mtrs long.(400 Kg.)

XLPE Insulated ACSR Rabbit (For HT)

LT XLPE Cable

Size 4CX70 SQ. mm

Size 4CX185 SQ. mm

Size 4CX120 SQ. mm

11 /0.4 KV Al wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

LT Supply Pillar Box of 200 Amp. capacity as per specification of Nigam .

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11/0.4 KV SubStation structure set on existing poles in all respect with clamps made from M.S. channel 100x50 X6 mm and 75x40 mm, M.S. angle 50x50x6 and M.S. flat 50x6 mm and 50x8 mm weight(147.3 kgs.) Approx (All galvanized as per relevant IS)

Horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

LIGHTENING ARRESTOR ( FEEDER TYPE) ON ERECTED STRUCTURE / SUPPORT ( SET OF 3 NOS. )

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

Danger plate of size 200 X 250 mm complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

LT Ariel Bunch Cable

PCC Poles

PCC Pole 9 mtrs long (200 KG)

Overhead ABC(Aerial bunched cable) with Bare Messenger

3C X25 +1CX25 sqmm

3C X50 +1CX35 sqmm

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Dead end (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

Suspension (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

LT insulation piercing connectors NFC Type A (main to tap) (main 16-50 mm2, Tap off 2.5-16 mm2)

LT insulation piercing connectors NFC type B ( main to main) (size 16-50 mm2)

(F-2)Construction of New 33/11 KV Sub Station (RURAL)

5 MVA 33/11KV Copper wound Power Transformer complete with first filling of transformer oil , OFF circuit tap changer and all fittings

Outdoor 11 KV O/D VCB KIOSK complete with accessories including use of special tools

Outdoor 36 KV O/D VCB KIOSK complete with accessories including use of special tools

33/11KV S/S structure (Galvanized) on existing PCC Poles including necessary nut & bolts & clamps etc. steel wt. 4087 Kg. made of MS Channel 100x50, MS Flat 50x6 and MS Sheet as per approved design and drawing.

Control Cable of size 4 X 4 SQ.MM. 1100 Volts PVC Insulated including supplyof ferrules

Control Cable of size 12C X 2.5 SQ.MM. 1100 Volts PVC Insulated including supply of ferrules

Overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing

Earth mesh (Galvanized) at sub-station as per approved map & design using MS Flat 50 x 6 mm & MS rod 20 mm dia (Galvanized)

M.S. Flat 50 X 6 mm (Galvanized) for earthing

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

Earthing electrode shall consist of G.I. Pipe 100 mm,of 3 Mtr Length. .

Maintenance free Gel Earthing with Pipe in pipe / Pipe in strip technology filled with anti corrosive conductive compound ( CPRI Tested )

11 /0.4 KV 25 KVA Al wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming

Mesh on the guarding for crossing as per standard or required as per location including binding as per drawing for road/P&T/Power line crossing

Metering points on 11 KV outgoing feeder at 33/11 KV S/S. (including following cost of (a) and (b) )

(a) Mounting structure (Galvanized)

(b) The requisite steel members will be supplied by contractor including the hardware.Contractor shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor.

Installation of Metering equipments:

11KV CT PT Set(200/5 Amp.)

MIP meter box.The meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 NOS

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

11 KV ROASTER SWITCH WITHOUT ON EXISTING BRACKET COMPLETE IN ALL RESPECT AS REQUIRED INCLUDING HARDWARE NUT, BOLTS & WASHER ETC.

11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps nut and bolts as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm weight(92.969 kgs.) Approx

33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works.

PCC Poles

PCC Ploe 9.0 mtrs long.(400 Kg.)

45 KN Composite polymer insulators for 33 KV on brackets complete including all acessories like hardware fitting etc.

45KN. porcelain disc.insulators for 11 KV ( each unit consisting of disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Porcelain 33KV Pin Insulator with Pins on pole complete in all respect

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps (For Dog) made of aluminum alloy as per IS:617-1994 (with latest amendments if any). All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

11 KV Danger plate of size 200 X 250 mm complete in all respect

NEW Incoming 33 KV Feeders (RURAL)

33 KV Overhead Line

PCC Poles

PCC Pole 9 mtrs long (400 KG)

33 KV double pole line structure set (Galvanized) on 9mtrs PCC poles for cut point complete on existing poles in all respect as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 65x65x6 ,M.S. Angle 50x50x6 mm and M.S. flat 50x6 mm [excluding cost of pole] weight(130.338 kgs.) Approx

33 KV Cross Arm with Top Hamper with clamps (Galvanized) made of MS Angle 75x75x6mm, clamp 50X10 mm, earth clamp 50X6 mm (wt.=23.486 approx)

33 KV PORCELAIN PIN INSULATOR WITH PIN ON EXISTING POLE COMPLETE INCLUDING ALL ACCESSSORIES LIKE HARDWARE FITTING AND NUTS AND BOLTS ETC.

45 KN Composite polymer insulators for 33 KV on brackets complete including all acessories like hardware fitting etc.

Overhead steel cored aluminum ACSR Dog conductor in all respect

PG clamps (For Dog) made of aluminum alloy as per IS:617-1994 (with latest amendments if any). All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

GS Stay set complete with 20 mm dia., 2.4 meter long stay rod with zinc coated steel Anchor Plate of size 300x300x4 mm with square hole of size 18x18 mm at centre IN GROUND AND GS STAY WIRE 7/8 MM TIGHTENED THROUGH 33 KV STAY INSULATOR INCLUDING CLAMPS

6 SWG GI Wire for continuous earthing of 33 KV Line hot dip (Galvanised) as per technical specification, approved drawings and scope of work.

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length along with G.I wire 8 SWG (approx. total length / weight, 50 meter/4.907 Kg. ) .

Danger plate of size 200 X 250 mm complete in all respect

11 KV OUTGOING FEEDERS (INTERCONNECTION):

11 KV Over Head Line Work

PCC Poles

PCC Pole 9 mtrs long (200 KG)

11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps nut and bolts as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm weight(92.969 kgs.) Approx

Overhead steel cored aluminum ACSR Rabbit conductor in all respect

11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

11 KV Danger plate of size 200 X 250 mm complete in all respect

1.4 Mtr Channel bracket with clamp

11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING.

(G) Installation of Capacitors for AG Consumers

For Ag consumers(5.0 to & 7.5 Hp) - 3 KVAR

For Ag consumers(7.5 to & 10.0 Hp) - 6 KVAR

For Ag consumers(Above 10.0 Hp) - 6 KVAR

(H) Infrastructure of Public Vehicles (EV) Charging Stations

SUB STATION STRUCTURE

PCC Poles

PCC Ploe 9.0 mtrs long.(400 Kg.)

11 /0.4 KV Al wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

LT Supply Pillar Box of 200 Amp. capacity as per specification of Nigam .

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11/0.4 KV SubStation structure set on existing poles in all respect with clamps made from M.S. channel 100x50 X6 mm and 75x40 mm, M.S. angle 50x50x6 and M.S. flat 50x6 mm and 50x8 mm weight(147.3 kgs.) Approx (All galvanized as per relevant IS)

Horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

LIGHTENING ARRESTOR ( FEEDER TYPE) ON ERECTED STRUCTURE / SUPPORT ( SET OF 3 NOS. )

Earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

Danger plate of size 200 X 250 mm complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

PCC Poles

PCC Pole 9 mtrs long (200 KG)

11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps nut and bolts as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm weight(92.969 kgs.) Approx

Overhead steel cored aluminum ACSR Rabbit conductor in all respect

11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

Earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

11 KV 45KN composite polymer Pin Insulator complete in all respect

PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

11 KV Danger plate of size 200 X 250 mm complete in all respect

11 KV UnderGround Line with 3C*185 SQMM

UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED

Under ground Cable of Size 3X185 SQ.MM for 11 KV

G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK)

GI PIPE for Cable Support at Pole ( Each 3 Mtr )

CABLE FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

Description of Work / Item(s)

Amount

(A)Bifurcation of 33 KV Line due to overloading

33 KV Bay

Grass cutting and surface dressing including removal of unwanted/rubbish plants with roots from open ground /yard and other Nigam premises with stacking of grass/plants at desired place near the ground.

Levelling of ground up to 30 cm.depth. with tractor and T&P required as per condition of ground including removal of rubbish plants from ground & marking of boundary with lime powder.(Including all lead & lifting)

Erection of outdoor 36 KV O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect

Drawing of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing including PG clamp

Laying of M.S. Flat 50 X 6 mm (Galvanized) for earthing

Erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Fixing of GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 NOS

Fixing of 33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works.

erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum for 8 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Ploe 9.0 mtrs long.(400 Kg.)

In normal soil

In Hard Soil

In ordinary rock which does not require drilling

In Hard Soil which require blasting or through drilling

Constn. Of 36 KV VCB Kiosk Platform 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect. (including supply of material)

Fixing of 45 KN Composite polymer insulators for 33 KV on brackets complete including all acessories like hardware fitting etc.

fixing of porcelain 33KV Pin Insulator with Pins on pole complete in all respect

Ffixing of PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

Fixing of 33 kV Danger plate of size 200 X 250 mm complete in all respect

33 KV UNDERGROUND CABLE

ERECTION OF 9.0 MTR. PCC POLES (400 KG) IN ALLIGNMENT INCLUDING EXCAVATION OF PIT IN GROUND AND BACK FILLING SOIL CONSOLIDATING EACH DEPOSIT LAYER OF 0.15 MTR. BY PROPER WATERING & RAMMING ETC. IN THE LENGTH.

PCC Pole 9 mtrs long (400 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

ERECTION OF 12.8 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING With 03 NOS. of 33 KV Channel Cross Arm(100x50 mm) with 48 NOS. of Nut & Bolts(M 16x45) INCLUDING EXCAVATION OF PIT 1.50 X 1.50 X 2.10 M IN GROUND. THE TOWER SHOULD BE ERECTED BY CC GROUTING & MUFFED IN CEMENT CONCRETE OF MIX RATIO 1:3:6 HAVING SIZE OF 1.20 X 1.20 X 2.10 M OVER BASE CONCRETE OF 100 MM THICK IN MIX 1:5:10 AS PER IS SPECIFICATIONS. THE REMAINING POSITION OF THE PIT BE BACK FILLED WITH WATERING & RAMMING AND SURPLUS MATERIAL SHALL BE DISPOSE- OFF WITHIN LEAD OF 50 M. (Galvanized) Weight(580.827 kg)

IN ALL TYPES OF ordinary SOIL - TOWER WEIGHT - 580.827 KG

IN ALL TYPES OF HARD SOIL - TOWER WEIGHT - 580.827 KG

ORDINARY ROCK (WHERE BLASTING IS NOT REQUIRED) / PACCA ROAD -TOWER WEIGHT 580.827 KG.

HARD ROCK/CC ROAD WHERE BLASTING/DRILLING IS REQUIRED -TOWER WEIGHT 580.827 KG.

LAYING, ENERGISATION & COMMISSIONING OF UNDERGROUND CABLE FOR WORKING VOLTAGE OF 33KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED IN EXCAVATED TRENCH AS PER IE RULES AND METHODS OF IS:1255, 25 CM. THICK UNDER LAYER OF SAND, II CLASS BRICK COVERING, REFILLING OF EARTH IN THE REMAINING PORTION, MAKING NECESSARY CONNECTION INCLUDING TESTING ETC. AS REQUIRED AND PROVIDING /FIXING CABLE ROUTE INDICATORS AT EVERY 30 MTR OF CABLE & AT EVERY TURN (AS PER LATEST SPECIFICATIONS AND DESIGN & DRAWING APPROVED BY NIGAM). [ROAD CROSSING OF CABLE SHALL BE IN DOUBLE WALLED CORRUGATED PIPE OF APPROPRIATE DIAMETER]

Under ground Cable of Size 3X300 SQ.MM for 33 KV

In open air and loop

Through open trench (Kaccha road/soil)

Through open trench (Pakka road/ordinary rock)

Through HDD Vermier(Hard Rock)

Through manual trench less (Bogie)

PROVIDING AND FIXING OF G.I. PIPE OF 150 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 33 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE END TERMINATION KIT/ST JOINT, MAKING OUTDOOR JOINT FOR 33 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE WITH OUTDOOR AND TERMINAL END PREPARATION OF JOINT AS PER MANUFACTURES KIT GUIDANCE AND DIRECTION INCLUDING PREPARATION OF CABLE END & TESTING ETC

XLPE 3X300 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X300 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X300 SQ.MM H.S.S.T. JOINT

FABRICATION AND FIXING OF BACK CLAMP AND STAY CLAMP USING MS FLAT 50X10MM(COLD BENDING) FOR CROSS ARMS, STAY, EARTH AND GUARDING BRACKET OF MS FLAT INCLUDING CUTTING WELDING DRILLING OF HOLES IN ALL RESPECT AS PER DESIGN AND DRAWING INCLUDING REQUIRED NUT BOLTS. (Galvanized as per IS)

INSLLATION OF HD GALVANISED M.S.ROD TYPE EARTHING SET MADE UP OF M.S.ROD 20 MM DIA. 3 METER LONG ALONGWITH EARTHING CLAMP & 8 SWG EARTH WIRE 15 METER LONG (FOR EARTHING OF 33 KV LINE) DRIVEN BY MECHANICAL MEANS INTO EARTH HOLE (MADE BY AUGERING) AND CONNECTING THE MS ROD TYPE EARTHING SET WITH CROSS ARMS, TOP HAMPERS, PCC POLE/STRUCTURE & EARTH WIRE ETC.

33 KV OVERHEAD LINE WORK

CONDUCTING ROUTE SURVEY , TRIMMING OF TREE BRANCHES ALONG THE ROAD AS PER APPROVED ROUTE MAP AND PEGGING OF ROUTE WITH SECTION POINT/DOUBLE POLE LOCATION FOR SPECIFIED NUMBERS OF DIFFERENT WORKS AT DIFFERENT LOCATIONS.

ERECTION OF 9.0 MTR. PCC POLES (400 KG) IN ALLIGNMENT INCLUDING EXCAVATION OF PIT IN GROUND AND BACK FILLING SOIL CONSOLIDATING EACH DEPOSIT LAYER OF 0.15 MTR. BY PROPER WATERING & RAMMING ETC. IN THE LENGTH.

PCC Pole 9 mtrs long (400 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

ERECTION OF 12.8 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING With 03 NOS. of 33 KV Channel Cross Arm(100x50 mm) with 48 NOS. of Nut & Bolts(M 16x45) INCLUDING EXCAVATION OF PIT 1.50 X 1.50 X 2.10 M IN GROUND. THE TOWER SHOULD BE ERECTED BY CC GROUTING & MUFFED IN CEMENT CONCRETE OF MIX RATIO 1:3:6 HAVING SIZE OF 1.20 X 1.20 X 2.10 M OVER BASE CONCRETE OF 100 MM THICK IN MIX 1:5:10 AS PER IS SPECIFICATIONS. THE REMAINING POSITION OF THE PIT BE BACK FILLED WITH WATERING & RAMMING AND SURPLUS MATERIAL SHALL BE DISPOSE- OFF WITHIN LEAD OF 50 M. (Galvanized) Weight(580.827 kg)

IN ALL TYPES OF ordinary SOIL - TOWER WEIGHT - 580.827 KG

IN ALL TYPES OF HARD SOIL - TOWER WEIGHT - 580.827 KG

ORDINARY ROCK (WHERE BLASTING IS NOT REQUIRED) / PACCA ROAD -TOWER WEIGHT 580.827 KG.

HARD ROCK/CC ROAD WHERE BLASTING/DRILLING IS REQUIRED -TOWER WEIGHT 580.827 KG.

Erection of 33 KV 'V' cross arms with TOP Hamper made of MS Angle75X75X6 mm with clamp of size 50X10 mm,earth clamp50X6 mm with nuts, bolts & Washers as per latest specification and drawings adopted & approved by Nigam (Galvanized as per IS)

FIXING OF A SET OF 4 NOS. 33KV 'V' CROSS ARMS(CHAKRI) MADE OF M.S. CHANNEL 100X50 MM ISMC [9.56 KG PER MTRS.] ON THE EXISTING LATTICE TOWER WITH BRACING OF M.S. FLAT ( 50 X 10 MM) INCLUDING NUT AND BOLTS ETC. WEIGHT OF THE ITEM WILL BE AS PER DRAWING

Fixing of a set of 4 NOS. 33 KV 'V' cross arms (Chakri) made of M.S.Angle 75x75x6 mm with bracing of M.S.Flat 50 x 10 mm including all necessary clamps, nuts & bolts etc. (Galvanized as per IS)

FIXING OF M.S. CHANNEL [CUT POINT ] 100X50 MM ISMC [9.56 KG. PER MTR] 2X1.8 MTRS LONG WITH PILOT PATTI 50X6MM [2.36 Kg. per mtr] THICK AND NECESSARY NUTS AND BOLTS ETC. WEIGHT OF THE CUT POINT CHANNEL WILL BE AS PER DRAWING APPX. 39.00 Kg. (Galvanized as per IS).

FIXING OF 33 KV DOUBLE POLE LINE STRUCTURE SET FOR CUT POINT COMPLETE ON EXISTING POLES IN ALL RESPECT WITH CLAMP, NUT & BOLTS AS REQURIED MADE FROM M.S.CHANNEL 100 X 50 X ISMC ( 9.56 KG. PER MTR.) ISA M.S.ANGLE 65 X 65 X 6 MM, M.S.ANGLE 50 X 50 X 6 MM AND M.S.FLAT 50 X 6 MM.(Galvanized as per IS)

FIXING OF 33 KV PORCELAIN PIN INSULATOR WITH PIN ON EXISTING POLE COMPLETE INCLUDING ALL ACCESSSORIES LIKE HARDWARE FITTING AND NUTS AND BOLTS ETC.

FIXING OF 3 NO. 11 KV B&S TYPE 120 KN PORCELAIN DISC INSULATOR ON COMPLETE LINE DP INCLUDING ALL ACCESSORIES LIKE HARDWARE FITTING 1 NO. AND NUTS AND BOLTS ETC.

Erection of GS Stay set complete with 20 mm dia., 2.4 meter long stay rod with zinc coated steel Anchor Plate of size 300x300x4 mm with square hole of size 18x18 mm at centre IN GROUND AND GS STAY WIRE 7/8 MM TIGHTENED THROUGH 33 KV STAY INSULATOR INCLUDING CLAMPS INCLUDING excavation of pit size 0.75x0.5x1.6 CUM in ground for all type of soil refilling, grouted and muffed in cement concrete.

SOIL (EVERY TYPE)

ORDINARY ROCK / PACCA ROAD

HARD ROCK/CC ROAD

By drilling method (Wherever required)

DRAWING OF GS WIRE NO.6 SWG HOT DIP GALVANIZED [5.0 MM DIA] COMPLETE IN ALL RESPECTS WITH BINDING WIRE EACH POLE WITH TOP HAMPER & CROSS ARM (WITH 1.1 M WIRE).

Drawing of overhead ACSR 100 Sq.mm. Dog conductor on existing cross arms through insulator including binding with 6 mm soft aluminium conductor & twisting etc. complete in all respect. (Cost of material includes the sag and jumpering)

ACSR Dog conductor

Fixing of PG Clamps for Dog conductor

INSLLATION OF HD GALVANISED M.S.ROD TYPE EARTHING SET MADE UP OF M.S.ROD 20 MM DIA. 3 METER LONG ALONGWITH EARTHING CLAMP & 8 SWG EARTH WIRE 15 METER LONG (FOR EARTHING OF 33 KV LINE) DRIVEN BY MECHANICAL MEANS INTO EARTH HOLE (MADE BY AUGERING) AND CONNECTING WITH G.I.EARTH WIRE.

PROVIDING AND LAYING OF CEMENT CONCERETING M.10 GRADE [ 1:3:6 ONE CEMENT THREE COARSE SAND,6 GRADED STONE AGGREGATE] INCLDUING CURING COMPACTION ETC. COMPLETE USING STONE AGGREGATE 20 MM NOMINAL SIZE.IN FOUNDATION AND PLINTH.

FABRICATION AND FIXING OF BACK CLAMP AND STAY CLAMP FOR CROSS ARMS, STAY, EARTH AND GUARDING BRACKET OF MS FLAT INCLUDING CUTTING, WELDING DRILLING OF HOLES IN ALL RESPECT AS PER DESIGN AND DRAWING.

FIXING OF 33KV DANGER PLATE ON THE TOWERS/ POLES COMPLETE IN ALL RESPECT AS PER DRAWING.

FIXING OF ISA M.S. ANGLE 50X50X6 MM (Galvanized as per IS)

FIXING OF ISA M.S. ANGLE 65X65X6 MM (Galvanized as per IS)

FIXING OF ISA M.S. Flat 50X 6 (Galvanized as per IS)

FIXING OF ISA M.S. Channel 100X50X6 (Galvanized as per IS)

(B)Bifurcation of 11 KV Line due to oveloading

11 KV Bay

Grass cutting and surface dressing including removal of unwanted/rubbish plants with roots from open ground /yard and other Nigam premises with stacking of grass/plants at desired place near the ground.

Levelling of ground up to 30 cm.depth. with tractor and T&P required as per condition of ground including removal of rubbish plants from ground & marking of boundary with lime powder.(Including all lead & lifting)

Erection of outdoor 11 KV O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (excluding civil works).

Laying, Testing Termination of control Cable of size 12C X 2.5 SQ.MM. 1100 Volts PVC Insulated including installation of ferrules to design various cores of control cables by terminal no. of identification including utilisation of cable gland.

Drawing of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing

Laying of M.S. Flat 50 X 6 mm (Galvanized) for earthing

Erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Installation of metering points on 11 KV outgoing feeder at 33/11 KV S/S.The installation work to be carried out as per drawing/design,under the supervision of concern Assistant Engineer (including erection cost of (a), (b), (c), (f), (g), (h) )

(a) Mounting structure (Galvanized)

(b) The requisite steel members shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor.

Civil works

(c) Erection of lattices in alignment including excavation and concreting of structure foundation including cement, sand and grit 20 mm size (crusher broken) having ratio 1:3:6 and grit 40 mm size for ratio 1:5:10 and curing for period as required (21 days). Area of concreting will be as per the drawing.

Installation of Metering equipments:

(d) Installation 11KV CT PT Set(200/5 Amp.)

(e) Installation MIP meter boxThe meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

Painting

(f) All surfaces interior and exterior of lattice structure shall be white aluminium painted

(g) The required cables from CTPT set to meter box laid down in 50 mm GI pipe with suitable bends & nipples, shall be provided by contractor alongwith the consumable items such as PVC tapes, petroleum jelly etc. The cable should be PVC multi strand copper 4 core 2.5/4 Sq. mm ISI marked and firm & tight connections shall be made by suitable connector e.g. at CTPT sets by using clamps and at meter/TTB by suitable lugs etc. The CTPT sets so installed shall be earthed by means of the MS Flat (size 50x6 mm) by joining it with the nearest earthing available at the sub-station. Requisite earthing material shall be made available by the contractor.

(h) Commissioning of Metering Equipments:Installed meters inside the box and metering equipments duly mounted on the mounting structure will be powered up by connecting load in the presence of the concerned Assistant Engineer who will arrange the necessary shut down. The completion certificate shall be furnised by contractor.be filled accordingly. Since the work involves higher A.C. voltage level, the contractor shall take full care regarding safety norms, so as to avoid any accidental hazards.

Fixing of GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum for 8 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC POLE 9.0 mtrs long.(200 Kg.)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Constn. Of 11 KV VCB Kiosk Platform 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the platform finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect. (including supply of material)

Fixing of ,45KN. porcelain disc.insulators for 11 KV ( each unit consisting of disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

Fixing of 11 kV Danger plate of size 200 X 250 mm complete in all respect

Erection of M.S Channel 100x50x6mm

Erection of M.S Angle 65x65x6mm

11 KV UnderGround Cable Work

ERECTION OF 9.00 M PCC POLES (200 KG) IN ALLIGNMENT INCLDUING EXCAVATION OF PIT IN GROUND AND BACK FILLING OF SOIL CONSOLIDATING EACH DEPOSIT LAYER OF 0.15 MTR. BY PROPER WATERING & RAMMING ETC. IN THE LENGTH.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

LAYING, ENERGISATION & COMMISSIONING OF UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED AS PER IE RULES AND METHODS OF IS:1255/JVVNL STANDARDS INCLUDING EXCAVATION OF 30 CMX120CM DEEP TRENCH IN LAND SPECIFIED AS BELOW, 25 CM. THICK UNDER LAYER OF SAND, "A" CLASS BRICK COVERING, REFILLING OF EARTH IN THE REMAINING PORTION, MAKING NECESSARY CONNECTION INCLUDING TESTING ETC. AS REQUIRED AND PROVIDING /FIXING CABLE ROUTE INDICATORS AT EVERY 30 MTR OF CABLE & AT EVERY TURN (AS PER LATEST SPECIFICATIONS AND DESIGN & DRAWING APPROVED BY NIGAM).[ROAD CROSSING OF CABLE SHALL BE IN DOUBLE WALLED CORRUGATED PIPE OF 200 MM DIAMETER]

Under ground Cable of Size 3X185 SQ.MM for 11 KV

In open air and loop

Through open trench (Kaccha road/soil)

Through open trench (Pakka road/ordinary rock)

Through HDD Vermier(Hard Rock)

Through manual trench less (Bogie)

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE END TERMINATION KIT/ST JOINT, MAKING OUTDOOR JOINT FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE WITH OUTDOOR AND TERMINAL END PREPARATION OF JOINT AS PER MANUFACTURES KIT GUIDANCE AND DIRECTION INCLUDING PREPARATION OF CABLE END & TESTING ETC

XLPE 3X185 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

insllation of HD Galvanised M.S.Rod type earthing set (including nuts & bolts) made up of M.S.Rod 20 mm dia. 3 meter long alongwith earthing clamp & 8 SWG earth wire 15 meter long (for earthing of 11 KV line) driven by mechanical means into earth hole (made by augering) and connecting the MS Rod type earthing set with cross arms, top hampers, PCC pole/structure & earth wire etc.

11 KV Over Head Line Work

Conducting route survey as per approved route map and pegging of route with section point/double pole location

Trimming of tree branches and preparing route appraoches for the proposed line

erection of PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs 200 Kg in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

ERECTION OF 11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING INCLUDING EXCAVATION OF PIT 1.50 X 1.50 X 2.10 M IN GROUND. THE TOWER SHOULD BE ERECTED BY CC GROUTING & MUFFED IN CEMENT CONCRETE OF MIX RATIO 1:3:6 HAVING SIZE OF 1.20 X 1.20 X 2.10 M OVER BASE CONCRETE OF 100 MM THICK IN MIX 1:5:10 AS PER IS SPECIFICATIONS. THE REMAINING POSITION OF THE PIT BE BACK FILLED WITH WATERING & RAMMING AND SURPLUS MATERIAL SHALL BE DISPOSE- OFF WITHIN LEAD OF 50 M.

IN ALL TYPES OF Ordinary SOIL - TOWER WEIGHT - 449.85 KG

IN ALL TYPES OF Hard SOIL - TOWER WEIGHT - 449.85 KG

ORDINARY ROCK (WHERE BLASTING IS NOT REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

ORDINARY ROCK (WHERE BLASTING/drilling is REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

fixing of 11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Drawing of overhead steel cored aluminum ACSR Rabbit conductor in all respect

fixing of 11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In Ordinary/normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986

Erection of 8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of 1.4 Mtr Channel bracket with clamp

(C)HVDS works

11 KV Overhead Line-1-Phase

Conducting route survey as per approved route map and pegging of route with section point/double pole location

Trimming of tree branches and preparing route appraoches for the proposed line

erection of PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs 200 Kg in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Drawing of overhead steel cored aluminum ACSR WEASEL [30 sq.mm (6+1)/(2.59+2.59) mm ]conductor

Fixing of 11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of LT Porcelain Pin insulators with pins

Erection of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended)

erection of 8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of 1.4 Mtr Channel bracket with clamp

11 KV Overhead Line-3-Phase

Conducting route survey as per approved route map and pegging of route with section point/double pole location

Trimming of tree branches and preparing route appraoches for the proposed line

erection of PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs 200 Kg in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

ERECTION OF 11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING INCLUDING EXCAVATION OF PIT 1.50 X 1.50 X 2.10 M IN GROUND. THE TOWER SHOULD BE ERECTED BY CC GROUTING & MUFFED IN CEMENT CONCRETE OF MIX RATIO 1:3:6 HAVING SIZE OF 1.20 X 1.20 X 2.10 M OVER BASE CONCRETE OF 100 MM THICK IN MIX 1:5:10 AS PER IS SPECIFICATIONS. THE REMAINING POSITION OF THE PIT BE BACK FILLED WITH WATERING & RAMMING AND SURPLUS MATERIAL SHALL BE DISPOSE- OFF WITHIN LEAD OF 50 M.

IN ALL TYPES OF Ordinary SOIL - TOWER WEIGHT - 449.85 KG

IN ALL TYPES OF Hard SOIL - TOWER WEIGHT - 449.85 KG

ORDINARY ROCK (WHERE BLASTING IS NOT REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

ORDINARY ROCK (WHERE BLASTING/drilling is REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

Fixing of 11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Drawing of overhead steel cored aluminum ACSR Rabbit conductor in all respect

Fixing of 11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986

erection of 8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of 1.4 Mtr Channel bracket with clamp

11 KV Underground Cable

ERECTION OF 9.00 M PCC POLES (200 KG) IN ALLIGNMENT INCLDUING EXCAVATION OF PIT IN GROUND AND BACK FILLING OF SOIL CONSOLIDATING EACH DEPOSIT LAYER OF 0.15 MTR. BY PROPER WATERING & RAMMING ETC. IN THE LENGTH.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

LAYING, ENERGISATION & COMMISSIONING OF UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED AS PER IE RULES AND METHODS OF IS:1255/JVVNL STANDARDS INCLUDING EXCAVATION OF 30 CMX120CM DEEP TRENCH IN LAND SPECIFIED AS BELOW, 25 CM. THICK UNDER LAYER OF SAND, "A" CLASS BRICK COVERING, REFILLING OF EARTH IN THE REMAINING PORTION, MAKING NECESSARY CONNECTION INCLUDING TESTING ETC. AS REQUIRED AND PROVIDING /FIXING CABLE ROUTE INDICATORS AT EVERY 30 MTR OF CABLE & AT EVERY TURN (AS PER LATEST SPECIFICATIONS AND DESIGN & DRAWING APPROVED BY NIGAM).[ROAD CROSSING OF CABLE SHALL BE IN DOUBLE WALLED CORRUGATED PIPE OF 200 MM DIAMETER]

Under ground Cable of Size 3X185 SQ.MM for 11 KV

In open air and loop

Through open trench (Kaccha road/soil)

Through open trench (Pakka road/ordinary rock)

Through HDD Vermier(Hard Rock)

Through manual trench less (Bogie)

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE END TERMINATION KIT/ST JOINT, MAKING OUTDOOR JOINT FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE WITH OUTDOOR AND TERMINAL END PREPARATION OF JOINT AS PER MANUFACTURES KIT GUIDANCE AND DIRECTION INCLUDING PREPARATION OF CABLE END & TESTING ETC

XLPE 3X185 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

insllation of HD Galvanised M.S.Rod type earthing set (including nuts & bolts) made up of M.S.Rod 20 mm dia. 3 meter long alongwith earthing clamp & 8 SWG earth wire 15 meter long (for earthing of 11 KV line) driven by mechanical means into earth hole (made by augering) and connecting the MS Rod type earthing set with cross arms, top hampers, PCC pole/structure & earth wire etc.

1-Phase DTR

erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (400 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Installation of 6.35KV/240 V aluminium wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming

erection M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

Fixing of 6.35/0.24 KV substation structure for 5 KVA complete (galvanized as per IS) complete in all respect made of MS Channel, MS angle and MS flat etc. including nut ,bolt,flat and spring washer (as per latest specification and drawing adopted & approved by NIGAM) (36.054 Kg. + 2 Kg. approx.)

Fixing of 6.35/0.24 KV substation structure for 10/16/25 KVA complete (galvanized as per IS) complete in all respect made of MS Channel, MS angle and MS flat etc. including nut ,bolt,flat and spring washer (as per latest specification and drawing adopted & approved by NIGAM) (36.054 Kg. + 2 Kg. approx.)

Fixing of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

Fixing of 11 KV 100 Amp. Drop out cum isolator with 5.0 Amp. fuse & 12 KV post insulators including nut, bolt & washers as required as per technical specifications, approved drawings and scope of work.

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of Danger plate of size 200 X 250 mm complete in all respect

Fixing of PG clamps (Weasel to Weasel) made of aluminum alloy as per IS:617-1994 etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

3-Phase DTR

erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Ploe 9.0 mtrs long.(400 Kg.)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Supp & erection of XLPE Insulated ACSR Rabbit (For HT)

Erection of LT XLPE Cable

Size 4CX70 SQ. mm

Size 4CX185 SQ. mm

Size 4CX120 SQ. mm

Installation of 11 /0.4 KV Al/Cu wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

25 KVA (Aluminium)

40 KVA (Aluminium)

63 KVA (Aluminium)

100 KVA (Aluminium)

erection M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

Erection and foundation of LT Supply Pillar Box of 200 Amp. capacity as per specification of Nigam . Each Base should be grouted including excavation , bricks , sand, cement masonary of size 4"X3"X10" and 3' in ground & 1.5' above road level with muffing to support & mounting the Pillar . The masonary will have 4"X4" opening 2" below ground level two in rear side & one each in the remaining sides to facilitate entry & exit of incoming & outgoing cables inside the pillar box shall be connected to DP Earth with 7/10 SWG Stay Wire & Lugs duly bolted on the place meant for XLPE cables inside the box shall be fixed with clamps making connections / jumpers by Aluminium lugs / PG Clamps of required size on LT Distribution mains on one end & with MCB / with isolator on the other end. Lugs should be crimped with crimping tools including cost of lugs, etc.

Fixing of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

Fixing of 11/0.4 KV SubStation structure set on existing poles in all respect with clamps made from M.S. channel 100x50 X6 mm and 75x40 mm, M.S. angle 50x50x6 and M.S. flat 50x6 mm and 50x8 mm weight(147.3 kgs.) Approx (All galvanized as per relevant IS)

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

INSTALLATION OF LIGHTENING ARRESTOR ( FEEDER TYPE) ON ERECTED STRUCTURE / SUPPORT ( SET OF 3 NOS. ) INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., WITH ALL ACCESSORIES IN SEPARATE EARTH PIT

Fixing of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of Danger plate of size 200 X 250 mm complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

(D) Cabling Works in Theft Prone Area

LT Ariel Bunch Cable

erection of 9.0 Mtr.long (200 Kg.) PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.35 cum for 8 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Laying of overhead ABC(Aerial bunched cable) with Bare Messenger

1C X25 +1CX25 sqmm

3C X25 +1CX25 sqmm

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of Dead end (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

Fixing of Suspension (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

Fixing of LT insulation piercing connectors NFC Type A (main to tap) (main 16-50 mm2, Tap off 2.5-16 mm2)

Fixing of LT insulation piercing connectors NFC type B ( main to main) (size 16-50 mm2)

Spring loaded box (1 phase)

Spring loaded box (3 phase)

LT Underground Cable

Laying of 4 Core LT XLPE insulated PVC sheathed armoured Cable

Size 4CX70 SQ. mm

Size 4CX120 SQ. mm

Size 4CX185 SQ. mm

Size 4CX300 SQ. mm

ASSEMBLY & INSTALLATION OF LT DISTRIBUTION BOX AS PER SPECIFICATION OF NIGAM WITH BRICK MASONARY USING CEMENT MORTAR OF RATIO 1: 6. INCLUDING Erection OF BRICK & CEMENT MORTAR BY THE CONTRACTOR.

100 AMP LT DISTRIBUTION BOX

erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Laying of LT Armoured Service Cable (Overhead or Underground as per site requirement)

2CX4 Sq MM

4CX16 Sq MM

(E)Segregation of 11 KV Ag-Non Ag Feeders

11 KV Bay

Grass cutting and surface dressing including removal of unwanted/rubbish plants with roots from open ground /yard and other Nigam premises with stacking of grass/plants at desired place near the ground.

Levelling of ground up to 30 cm.depth. with tractor and T&P required as per condition of ground including removal of rubbish plants from ground & marking of boundary with lime powder.(Including all lead & lifting)

erection of outdoor 11 KV O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (excluding civil works).

Laying, Testing Termination of control Cable of size 4 X 4 SQ.MM. 1100 Volts PVC Insulated including installation of ferrules to design various cores of control cables by terminal no. of identification including utilisation of cable gland.

Laying, Testing Termination of control Cable of size 12C X 2.5 SQ.MM. 1100 Volts PVC Insulated including installation of ferrules to design various cores of control cables by terminal no. of identification including utilisation of cable gland.

Drawing of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing

laying of M.S. Flat 50 X 6 mm (Galvanized) for earthing

erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

Installation of metering points on 11 KV outgoing feeder at 33/11 KV S/S.The installation work to be carried out as per drawing/design,under the supervision of concern Assistant Engineer (including erection cost of (a), (b), (c), (f), (g), (h) )

(a) Mounting structure (Galvanized)

(b) The requisite steel members shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor.

Civil works

(c) Erection of lattices in alignment including excavation and concreting of structure foundation including cement, sand and grit 20 mm size (crusher broken) having ratio 1:3:6 and grit 40 mm size for ratio 1:5:10 and curing for period as required (21 days). Area of concreting will be as per the drawing.

Installation of Metering equipments:

(d) Installation 11KV CT PT Set(200/5 Amp.)

(e) Installation MIP meter boxThe meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

Painting

(f) All surfaces interior and exterior of lattice structure shall be white aluminium painted

(g) The required cables from CTPT set to meter box laid down in 50 mm GI pipe with suitable bends & nipples, shall be provided by contractor alongwith the consumable items such as PVC tapes, petroleum jelly etc. The cable should be PVC multi strand copper 4 core 2.5/4 Sq. mm ISI marked and firm & tight connections shall be made by suitable connector e.g. at CTPT sets by using clamps and at meter/TTB by suitable lugs etc. The CTPT sets so installed shall be earthed by means of the MS Flat (size 50x6 mm) by joining it with the nearest earthing available at the sub-station. Requisite earthing material shall be made available by the contractor.

(h) Commissioning of Metering Equipments:Installed meters inside the box and metering equipments duly mounted on the mounting structure will be powered up by connecting load in the presence of the concerned Assistant Engineer who will arrange the necessary shut down. The completion certificate shall be furnised by contractor.be filled accordingly. Since the work involves higher A.C. voltage level, the contractor shall take full care regarding safety norms, so as to avoid any accidental hazards.

Fixing of GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum for 8 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Constn. Of 11 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect. (including supply of material)

Fixing of ,45KN. porcelain disc.insulators for 11 KV ( each unit consisting of disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

Fixing of 11 kV Danger plate of size 200 X 250 mm complete in all respect

Erection of M.S Channel 100x50x6mm

Erection of M.S Angle 65x65x6mm

11 KV UnderGround Cable Work

ERECTION OF 9.00 M PCC POLES (200 KG) IN ALLIGNMENT INCLDUING EXCAVATION OF PIT IN GROUND AND BACK FILLING OF SOIL CONSOLIDATING EACH DEPOSIT LAYER OF 0.15 MTR. BY PROPER WATERING & RAMMING ETC. IN THE LENGTH.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

LAYING, ENERGISATION & COMMISSIONING OF UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED AS PER IE RULES AND METHODS OF IS:1255/JVVNL STANDARDS INCLUDING EXCAVATION OF 30 CMX120CM DEEP TRENCH IN LAND SPECIFIED AS BELOW, 25 CM. THICK UNDER LAYER OF SAND, "A" CLASS BRICK COVERING, REFILLING OF EARTH IN THE REMAINING PORTION, MAKING NECESSARY CONNECTION INCLUDING TESTING ETC. AS REQUIRED AND PROVIDING /FIXING CABLE ROUTE INDICATORS AT EVERY 30 MTR OF CABLE & AT EVERY TURN (AS PER LATEST SPECIFICATIONS AND DESIGN & DRAWING APPROVED BY NIGAM).[ROAD CROSSING OF CABLE SHALL BE IN DOUBLE WALLED CORRUGATED PIPE OF 200 MM DIAMETER]

Under ground Cable of Size 3X185 SQ.MM for 11 KV

In open air and loop

Through open trench (Kaccha road/soil)

Through open trench (Pakka road/ordinary rock)

Through HDD Vermier(Hard Rock)

Through manual trench less (Bogie)

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

GI PIPE for Cable Support at Pole ( Each 3.3 Mtr )

GI PIPE for Cable Support at Tower ( Each 3.3 Mtr )

CABLE END TERMINATION KIT/ST JOINT, MAKING OUTDOOR JOINT FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE WITH OUTDOOR AND TERMINAL END PREPARATION OF JOINT AS PER MANUFACTURES KIT GUIDANCE AND DIRECTION INCLUDING PREPARATION OF CABLE END & TESTING ETC

XLPE 3X185 SQ.MM H.S. ON INDOOR TYPE

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

XLPE 3X185 SQ.MM H.S.S.T. JOINT

insllation of HD Galvanised M.S.Rod type earthing set (including nuts & bolts) made up of M.S.Rod 20 mm dia. 3 meter long alongwith earthing clamp & 8 SWG earth wire 15 meter long (for earthing of 11 KV line) driven by mechanical means into earth hole (made by augering) and connecting the MS Rod type earthing set with cross arms, top hampers, PCC pole/structure & earth wire etc.

Fixing of double break without EB Isolator on existing bracket complete in all respect as required including hardware nut, bolts & washer etc.

11KV (with 9 x 12 KV Post Insulator ) 400 Amp. - as per latest specification, design & drawing approved by the NIGAM

11 KV Over Head Line Work

Conducting route survey as per approved route map and pegging of route with section point/double pole location

Trimming of tree branches and preparing route appraoches for the proposed line

erection of PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs 200 Kg in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

ERECTION OF 11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING INCLUDING EXCAVATION OF PIT 1.50 X 1.50 X 2.10 M IN GROUND. THE TOWER SHOULD BE ERECTED BY CC GROUTING & MUFFED IN CEMENT CONCRETE OF MIX RATIO 1:3:6 HAVING SIZE OF 1.20 X 1.20 X 2.10 M OVER BASE CONCRETE OF 100 MM THICK IN MIX 1:5:10 AS PER IS SPECIFICATIONS. THE REMAINING POSITION OF THE PIT BE BACK FILLED WITH WATERING & RAMMING AND SURPLUS MATERIAL SHALL BE DISPOSE- OFF WITHIN LEAD OF 50 M.

IN ALL TYPES OF SOIL - TOWER WEIGHT - 449.85 KG

IN ALL TYPES OF HARD SOIL - TOWER WEIGHT - 449.85 KG

ORDINARY ROCK (WHERE BLASTING IS NOT REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

ORDINARY ROCK (WHERE BLASTING/DRILLING IS REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

Fixing of 11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Drawing of overhead steel cored aluminum ACSR Rabbit conductor in all respect

Fixing of 11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986

erection of 8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of 1.4 Mtr Channel bracket with clamp

3-Phase DTR

erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Ploe 9.0 mtrs long.(400 Kg.)

In normal soil

In Hard Soil

In ordinary rock which does not require drilling

In Hard Soil which require blasting or through drilling

Supp & erection of XLPE Insulated ACSR Rabbit (For HT)

Erection of LT XLPE Cable

Size 4CX70 SQ. mm

Size 4CX185 SQ. mm

Size 4CX120 SQ. mm

Installation of 11 /0.4 KV Al wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

erection M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

Erection and foundation of LT Supply Pillar Box of 200 Amp. capacity as per specification of Nigam . Each Base should be grouted including excavation , bricks , sand, cement masonary of size 4"X3"X10" and 3' in ground & 1.5' above road level with muffing to support & mounting the Pillar . The masonary will have 4"X4" opening 2" below ground level two in rear side & one each in the remaining sides to facilitate entry & exit of incoming & outgoing cables inside the pillar box shall be connected to DP Earth with 7/10 SWG Stay Wire & Lugs duly bolted on the place meant for XLPE cables inside the box shall be fixed with clamps making connections / jumpers by Aluminium lugs / PG Clamps of required size on LT Distribution mains on one end & with MCB / with isolator on the other end. Lugs should be crimped with crimping tools including cost of lugs, etc.

Fixing of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

Fixing of 11/0.4 KV SubStation structure set on existing poles in all respect with clamps made from M.S. channel 100x50 X6 mm and 75x40 mm, M.S. angle 50x50x6 and M.S. flat 50x6 mm and 50x8 mm weight(147.3 kgs.) Approx (All galvanized as per relevant IS)

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

INSTALLATION OF LIGHTENING ARRESTOR ( FEEDER TYPE) ON ERECTED STRUCTURE / SUPPORT ( SET OF 3 NOS. ) INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., WITH ALL ACCESSORIES IN SEPARATE EARTH PIT

Fixing of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of Danger plate of size 200 X 250 mm complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

LT Ariel Bunch Cable

erection of 9.0 Mtr.long (200 Kg.) PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.35 cum for 8 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Laying of overhead ABC(Aerial bunched cable) with Bare Messenger

3C X25 +1CX25 sqmm

3C X50 +1CX35 sqmm

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of Dead end (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

Fixing of Suspension (anchor) clamps for insulated or bare messenger + one Pole Bracket + 1.5 mtr S.S. (Stainless Steel) Strap + two SS Buckles as per NFC Standard suitable for AB Cable Complete in all respect (galvanized as per IS)

Fixing of LT insulation piercing connectors NFC Type A (main to tap) (main 16-50 mm2, Tap off 2.5-16 mm2)

Fixing of LT insulation piercing connectors NFC type B ( main to main) (size 16-50 mm2)

(F-2)Construction of New 33/11 KV Sub Station (RURAL)

Grass cutting and surface dressing including removal of unwanted/rubbish plants with roots from open ground /yard and other Nigam premises with stacking of grass/plants at desired place near the ground.

Levelling of ground up to 30 cm.depth. with tractor and T&P required as per condition of ground including removal of rubbish plants from ground & marking of boundary with lime powder.(Including all lead & lifting)

Loading & unloading and erection, testing and commissioning of 5 MVA 33/11KV Copper wound Power Transformer complete with first filling of transformer oil , OFF circuit tap changer and all fittings

erection of outdoor 11 KV O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (excluding civil works).

erection of outdoor 36 KV O/D VCB KIOSK complete with accessories including use of special tools & conducting all pre commissioning tests before energisation, filling oil etc. complete in all respect with erection& grouting of structure (excluding civil works).

Fixing of 33/11KV S/S structure (Galvanized) on existing PCC Poles including necessary nut & bolts & clamps etc. steel wt. 4087 Kg. made of MS Channel 100x50, MS Flat 50x6 and MS Sheet as per approved design and drawing.

Laying, Testing Termination of control Cable of size 4 X 4 SQ.MM. 1100 Volts PVC Insulated including installation of ferrules to design various cores of control cables by terminal no. of identification including utilisation of cable gland.

Laying, Testing Termination of control Cable of size 12C X 2.5 SQ.MM. 1100 Volts PVC Insulated including installation of ferrules to design various cores of control cables by terminal no. of identification including utilisation of cable gland.

Drawing of overhead steel cored aluminum ACSR DOG[100SqMM(6+7) /(4.72+1.57)] conductor complete in all respect as per latest specification and drawing

Fixing of earth mesh (Galvanized) at sub-station as per approved map & design using MS Flat 50 x 6 mm & MS rod 20 mm dia including laying of flat at the depth 0.65 mtr & MS rod at 3 metre depth Welding & jointing at joints, structures & equipments etc. in switch yard area of 35 M x 35 M as per drawing (Galvanized)

laying of M.S. Flat 50 X 6 mm (Galvanized) for earthing

erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length

erection of earthing electrode shall consist of G.I. Pipe 100 mm,of 3 Mtr Length. The electrode shall be buried as far as practicable 3 meters below ground level. Wherever possible, earth electrodes shall be located as near the water tap, water drain or near down take pipe. Earth electrodes shall not be installed in proximity to a metal fence. It shall be kept clear of the buildings foundations and in no case it shall be nearer than 2 meters from the outer face of the wall. The electrode shall be surrounded with layer of charcoal dust and salt mixture through out the length. The 100 mm GI pipe shall be provided with holes of 12 mm dia. drilled at 75 mm interval upto 2.5 meters length from bottom. The top of the pipe shall be provided with a G.I. threaded cap for watering the earth through a pipe. A Clamp with Pati of 12" of M.S. Flat of size 50X6 mm shall be fixed (Bolted) on the top edge of the pipe which in turn shall be connected to Neutral / Body of the Power Transformer through M.S. Flat size 50X6 mm. The G.I. cap over the GI pipe shall be housed in a masonry chamber, approximately 300 mm x 300 mm x 300 mm deep. The masonry chamber shall be provided with a RCC inspection cover resting over a RCC frame, embedded in masonry.

Erection of Maintenance free Gel Earthing with Pipe in pipe / Pipe in strip technology filled with anti corrosive conductive compound ( CPRI Tested ) below the ground in 150 - 200 mm dia. earth pit & surrounding filled with required mineral filling compound ( MFC should have hygroscopic property to retain the moisture for long time to create low resistance zone ) and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size 300mm x 300mm complete testing of earth resistance as required. The value of Earth resistance shall be obtained 0.5 Ohm in individual earthing. G.I Pipe (IS: 1239 marks) GI pipe 3000 mm long, 80 I 40 mm, Terminal 12 mm GI Strip. Earthing as per 18:3043-1987

Installation of 11 /0.4 KV 25 KVA Al wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming

Drawing and laying of Mesh using GS Wire 8 SWG (Galvanized) on the guarding for crossing as per standard or required as per location including binding as per drawing for road / P&T/ Power Line crossing.

Installation of metering points on 11 KV outgoing feeder at 33/11 KV S/S.The installation work to be carried out as per drawing/design,under the supervision of concern Assistant Engineer (including erection cost of (a), (b), (c), (f), (g), (h) )

(a) Mounting structure (Galvanized)

(b) The requisite steel members shall joint/weld the members to form the mounting structure as per drawing.Necessary tools,welding ,machines,lifting devics etc. shall be arranged by contractor.

Civil works

(c) Erection of lattices in alignment including excavation and concreting of structure foundation including cement, sand and grit 20 mm size (crusher broken) having ratio 1:3:6 and grit 40 mm size for ratio 1:5:10 and curing for period as required (21 days). Area of concreting will be as per the drawing.

Installation of Metering equipments:

(d) Installation 11KV CT PT Set(200/5 Amp.)

(e) Installation MIP meter boxThe meter box will be fixed firmly with sufficient strength at a place as per drawing. The test terminal block(TTB) link type shall be provided by contractor in the meter box.

Painting

(f) All surfaces interior and exterior of lattice structure shall be white aluminium painted

(g) The required cables from CTPT set to meter box laid down in 50 mm GI pipe with suitable bends & nipples, shall be provided by contractor alongwith the consumable items such as PVC tapes, petroleum jelly etc. The cable should be PVC multi strand copper 4 core 2.5/4 Sq. mm ISI marked and firm & tight connections shall be made by suitable connector e.g. at CTPT sets by using clamps and at meter/TTB by suitable lugs etc. The CTPT sets so installed shall be earthed by means of the MS Flat (size 50x6 mm) by joining it with the nearest earthing available at the sub-station. Requisite earthing material shall be made available by the contractor.

(h) Commissioning of Metering Equipments:Installed meters inside the box and metering equipments duly mounted on the mounting structure will be powered up by connecting load in the presence of the concerned Assistant Engineer who will arrange the necessary shut down. The completion certificate shall be furnised by contractor.be filled accordingly. Since the work involves higher A.C. voltage level, the contractor shall take full care regarding safety norms, so as to avoid any accidental hazards.

Fixing of GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

33KV (with 18 x 24 KV Post Insulator ) 800 Amp.

11KV ( with 9 x 12 KV Post Insulator ) 400 Amp.

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc.

33KV ( with 12 x 24 KV Post Insulator ) 1 Set=3 NOS

11KV ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

FIXING OF 11 KV ROASTER SWITCH WITHOUT ON EXISTING BRACKET COMPLETE IN ALL RESPECT AS REQUIRED INCLUDING HARDWARE NUT, BOLTS & WASHER ETC.

Fixing of 11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps nut and bolts as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm weight(92.969 kgs.) Approx

Fixing of 33 KV Sub-station type (30 KV 10 KA Station class) (1 set=3 No.) lightening arrestors on the existing brackets in all respect as required including hardware, nut , bolt & washers etc. For O&M works.

erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum for 8 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Ploe 9.0 mtrs long.(400 Kg.)

In normal soil

In Hard Soil

In ordinary rock which does not require drilling

In Hard Soil which require blasting or through drilling

Construction of 33/11KV Transformers plate form 2.4 x 2.4x 2.0 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, stone masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 alongwith 2 NOS. M.S. Rails 90 Pounds of 2.4 Mtr. length each, alongwith cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect. (including supply of material)

Constn. Of 11KV/ 36 KV VCB Kiosk Plate form 3.0 x 1.5 x 1.5 Mtrs. Including excavation in all type of soil up to the depth of 900 mm, foundation concrete in C.C. - 1 : 5 :10 for 150 mm thickness, brick masonary in cement mortar of mix. 1:8 with top of the plate form finished with 100 mm layer of C.C. 1:2:4 including fixing of foundation bolts and cement plaster - 20 mm thick of mix ratio 1:6, on all the exposed surfaces of the plate form - complete in all respect. (including supply of material)

Fixing of 45 KN Composite polymer insulators for 33 KV on brackets complete including all acessories like hardware fitting etc.

Fixing of ,45KN. porcelain disc.insulators for 11 KV ( each unit consisting of disc insulators & one B&S Type hardware) on brackets complete including all acessories like hardware fitting etc.

Fixing of porcelain 33KV Pin Insulator with Pins on pole complete in all respect

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of PG clamps Dog to Dog on over headlines/jumpers, etc. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanising

Fixing of 11 kV Danger plate of size 200 X 250 mm complete in all respect

NEW Incoming 33 KV Feeders (RURAL)

33 KV Overhead Line

Conducting route survey as per approved route map and pegging of route with section point/double pole location

Trimming of tree branches and preparing route appraoches for the proposed line

erection of 9.0 mtrs long.(400 Kg.) PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (400 KG)

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

Fixing of 33 KV double pole line structure set (Galvanized) on 9mtrs PCC poles for cut point complete on existing poles in all respect as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 65x65x6 ,M.S. Angle 50x50x6 mm and M.S. flat 50x6 mm [excluding cost of pole] weight(130.338 kgs.) Approx

Fixing of 33 KV Cross Arm with Top Hamper with clamps (Galvanized) made of MS Angle 75x75x6mm, clamp 50X10 mm, earth clamp 50X6 mm (wt.=23.486 approx)

Fixing 33 KV porcelain Pin insulator with Pin on pole complete including all accessories like hardware fittings etc.

Fixing of 45 KN Composite polymer insulators for 33 KV on brackets complete including all acessories like hardware fitting etc.

Drawing of overhead steel cored aluminum ACSR Dog conductor in all respect

erection of PG clamps (For Dog) made of aluminum alloy as per IS:617-1994 (with latest amendments if any). All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

Erection of GS Stay set complete with 20 mm dia., 2.4 meter long stay rod with zinc coated steel Anchor Plate of size 300x300x4 mm with square hole of size 18x18 mm at centre IN GROUND AND GS STAY WIRE 7/8 MM TIGHTENED THROUGH 33 KV STAY INSULATOR INCLUDING CLAMPS INCLUDING excavation of pit size 0.75x0.5x1.6 CUM in ground for all type of soil refilling, grouted and muffed in cement concrete.

HARD SOIL / PACCA ROAD

HARD ROCK/CC ROAD

Erection of 6 SWG GI Wire for continuous earthing of 33 KV Line hot dip (Galvanised) as per technical specification, approved drawings and scope of work.

Erection of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length along with G.I wire 8 SWG (approx. total length / weight, 50 meter/4.907 Kg. ) .

Erection of Danger plate of size 200 X 250 mm complete in all respect

11 KV OUTGOING FEEDERS (INTERCONNECTION):

11 KV UnderGround Cable Work

11 KV Over Head Line Work

Conducting route survey as per approved route map and pegging of route with section point/double pole location

Trimming of tree branches and preparing route appraoches for the proposed line

Erection of PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs 200 Kg in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Fixing of 11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Drawing of overhead steel cored aluminum ACSR Rabbit conductor in all respect

Fixing of 11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

Fixing of 11KV T&C Type composite polymer insulator complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986

Erection of 8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

Fixing of 1.4 Mtr Channel bracket with clamp

ERECTION OF 11.4 MTR. LONG LATTICE TOWER MADE OF 65 X 65 X 5 MM M.S. ANGLE WITH 50 X 6 MM M.S. FLAT FOR BRACING INCLUDING EXCAVATION OF PIT 1.50 X 1.50 X 2.10 M IN GROUND. THE TOWER SHOULD BE ERECTED BY CC GROUTING & MUFFED IN CEMENT CONCRETE OF MIX RATIO 1:3:6 HAVING SIZE OF 1.20 X 1.20 X 2.10 M OVER BASE CONCRETE OF 100 MM THICK IN MIX 1:5:10 AS PER IS SPECIFICATIONS. THE REMAINING POSITION OF THE PIT BE BACK FILLED WITH WATERING & RAMMING AND SURPLUS MATERIAL SHALL BE DISPOSE- OFF WITHIN LEAD OF 50 M.

IN ALL TYPES OF HARD SOIL - TOWER WEIGHT - 449.85 KG

ORDINARY ROCK (WHERE BLASTING IS NOT REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

ORDINARY ROCK (WHERE BLASTING/DRILLING IS REQUIRED) / PACCA ROAD -TOWER WEIGHT 449.85 KG.

(G) Installation of Capacitors for AG Consumers

For Ag consumers(5.0 to & 7.5 Hp) - 3 KVAR

For Ag consumers(7.5 to & 10.0 Hp) - 6 KVAR

For Ag consumers(Above 10.0 Hp) - 6 KVAR

(H) Infrastructure of Public Vehicles (EV) Charging Stations

SUB STATION STRUCTURE

Erection of PCC Poles in all types of soil & allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs and 1.2x0.6x1.35 cum PCC poles in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Ploe 9.0 mtrs long.(400 Kg.)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Supp & erection of XLPE Insulated ACSR Rabbit (For HT)

Installation of 11 /0.4 KV Al wound, conventional outdoor type distribution transformers with all fittings and accessories and first filling of transformer oil alongwith MCCB. Protection on LV side confirming to technical specification

erection M.S. Flat 50 X 6 mm for mounting single phase transformer on poles.

Erection and foundation of LT Supply Pillar Box of 200 Amp. capacity as per specification of Nigam . Each Base should be grouted including excavation , bricks , sand, cement masonary of size 4"X3"X10" and 3' in ground & 1.5' above road level with muffing to support & mounting the Pillar . The masonary will have 4"X4" opening 2" below ground level two in rear side & one each in the remaining sides to facilitate entry & exit of incoming & outgoing cables inside the pillar box shall be connected to DP Earth with 7/10 SWG Stay Wire & Lugs duly bolted on the place meant for XLPE cables inside the box shall be fixed with clamps making connections / jumpers by Aluminium lugs / PG Clamps of required size on LT Distribution mains on one end & with MCB / with isolator on the other end. Lugs should be crimped with crimping tools including cost of lugs, etc.

Fixing of 11KV ( with 9 x 12 KV Post Insulator ) 400 Amp. GO double break without EB Isolator on existing bracket complete in all respect as required including hardware etc.

Fixing of 11/0.4 KV SubStation structure set on existing poles in all respect with clamps made from M.S. channel 100x50 X6 mm and 75x40 mm, M.S. angle 50x50x6 and M.S. flat 50x6 mm and 50x8 mm weight(147.3 kgs.) Approx (All galvanized as per relevant IS)

Fixing of horn gap sets on existing brackets in all respect as required including hardware nut & bolt & washer etc. ( with 6 x 24 KV Post Insulator ) 1 Set=3 NOS

INSTALLATION OF LIGHTENING ARRESTOR ( FEEDER TYPE) ON ERECTED STRUCTURE / SUPPORT ( SET OF 3 NOS. ) INCLUDING CONNECTION WITH EARTH BY 6 SWG GI WIRE AS REQUIRED AND JUMPERING ETC., WITH ALL ACCESSORIES IN SEPARATE EARTH PIT

Fixing of earthing rod sets for S/S made with MS Rod (Galvanized ) 20 mm dia, 3 meter length as per latest specification and drawing adopted & approved by NIGAM.

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of 11KV T&C Type composite polymer Insulators complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Fixing of Danger plate of size 200 X 250 mm complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994. All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986(latest amended) com plete in all respect as required for ACSR conductor,

Erection of PCC Poles in allignment including excavation of pit size 1.2x0.6x1.5 cum. for 9 mtrs 200 Kg in ground and back filling soil consolidating each deposit layer of 0.15 mtr. by watering and ramming etc. in the length.

PCC Pole 9 mtrs long (200 KG)

In normal soil

In Hard soil

In ordinary rock/Hard Soil which does not require blasting

In ordinary rock/Hard Soil which require blasting or through drilling

Fixing of 11 KV double pole line structure set (Galvanized) on existing poles in all respect with clamps as required made from M.S. channel 100x50 X6 mm ISMC [9.56 kg. per mtr] ISA M.S. angle 50x50x6 and M.S. flat 50x6 mm [excluding cost of pole/RS Joist] weight(93 kgs.) Approx

Drawing of overhead steel cored aluminum ACSR Rabbit conductor in all respect

Fixing of 11KV Cross Arm with Top Hamper with clamps made of MS Angle 65x65x6mm, clamp 50X6 mm, earth clamp 50X6 mm (Galvanized)

Fixing of GI stay set (Galvanized) complete (stay rod 16 mm dia,1.8 m long,anchor plate 300X300X4 mm,12 mm dia turn buckle) including stay clamps, strain insulator, Stay wire7/10 SWG

In normal soil

In Hard Soil

ordinary rock / PACCA road

HARD ROCK/CC ROAD( Where drilling/blasting is required)

Fixing of earthing rod set for 11 KV lines made with MS rod (Galvanised) 20 mm dia, 3 meter length along

drawing of 11KV T&C Type COMPOSITE POLYMER Insulators complete including all accessories like hardware fitting (as per latest specifications and drawings adopted & approved by NIGAM)

Fixing of 11 KV 45KN composite polymer Pin Insulator complete in all respect

Erection of PG clamps (For Rabbit) made of aluminum alloy as per IS:617-1994 . All ferrous metal part intended for outdoor use except those made of stainless steel shall be protected by hot dip galvanizing in accordance with IS 2633-1986

Erection of 8 SWG (4mm dia) GI Wire for continuous earthing of 11 KV Line hot dip (Galvanised)

Erection of 11 KV Danger plate of size 200 X 250 mm complete in all respect

11 KV UnderGround Line with 3C*185 SQMM

LAYING, ENERGISATION & COMMISSIONING OF UNDERGROUND CABLE FOR WORKING VOLTAGE OF 11KV ALUMINIUM CONDUCTOR (IS 7098) CABLE XLPE ARMOURED AS PER IE RULES AND METHODS OF IS:1255/JVVNL STANDARDS INCLUDING EXCAVATION OF 30 CMX120CM DEEP TRENCH IN LAND SPECIFIED AS BELOW, 25 CM. THICK UNDER LAYER OF SAND, "A" CLASS BRICK COVERING, REFILLING OF EARTH IN THE REMAINING PORTION, MAKING NECESSARY CONNECTION INCLUDING TESTING ETC. AS REQUIRED AND PROVIDING /FIXING CABLE ROUTE INDICATORS AT EVERY 30 MTR OF CABLE & AT EVERY TURN (AS PER LATEST SPECIFICATIONS AND DESIGN & DRAWING APPROVED BY NIGAM).[ROAD CROSSING OF CABLE SHALL BE IN DOUBLE WALLED CORRUGATED PIPE OF 200 MM DIAMETER]

Under ground Cable of Size 3X185 SQ.MM for 11 KV

In open air and loop

Through open trench (Kaccha road/soil)

Through open trench (Pakka road/ordinary rock)

Through HDD Vermier(Hard Rock)

Through manual trench less (Bogie)

PROVIDING AND FIXING OF G.I. PIPE OF 125 MM DIAMETER, B-CLASS (IS:1239 MARK), AT THE STARTING AND FINISHING POINT OF 11 KV UNDER GROUND CABLES AND TO LAY & CLAMP VERTICALLY WITH THE EXISTING SUPPORT, INCLUDING LABOUR CHARGES.

GI PIPE for Cable Support at Pole ( Each 3 Mtr )

CABLE END TERMINATION KIT/ST JOINT, MAKING OUTDOOR JOINT FOR11 KV ALUMINUM CONDUCTOR XLPE ARMOURED HT CABLE WITH OUTDOOR AND TERMINAL END PREPARATION OF JOINT AS PER MANUFACTURES KIT GUIDANCE AND DIRECTION INCLUDING PREPARATION OF CABLE END & TESTING ETC

XLPE 3X185 SQ.MM H.S. ON OUTDOOR TYPE

(I-1) Civil works of 18 NOS GSS (RURAL)

PART- 'A' (BUILDING WORK)

(1.8) Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter All kinds of soil.

(3.1.6) Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

(6.1.6) Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand).

Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix (4.1)

Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. (4.9)

(6.18.1) Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 :upto 15 cm thick.

(4.3) Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

(4.10.2) Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc.

(4.13.2) Providing and fabricating reinforcement for R.C.C. work includingstraightening, cutting, bending, placing in position and binding(including cost of binding wire) all complete up to floor five level.Hot rolled deformed bars (IS : 1139).

(5.8.3) Half brick masonry in Superstructure, using bricks of designation 75 in CM 1:6 upto third storey.

(5.2.2) Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand)

(10.17.1) Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

(3.8) Providing & fixing precast cement concrete coping 1 : 2 : 4 mix 50mm thick complete as per specification .

10.22 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

(9.19.3) Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :Windows side hung /Ventilators top or centre hung (openable) .

(9.26) Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance.

(9.27) Providing and fixing Square bars or other flat welded to window, ventilatiors etc.

(11.26) Random rubble dry stone Kharanja under floor.

(9.5) Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

(6.17.3) Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges : Kota stone minimum 30mm thick.

(8.13.2.1) Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' :comercial veneer both side 30 mm thick .

(9.17.1+9.17.2) Providing and fixing M.S. sheet double leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint M.S. Shhet 20 S.W.G.

Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish:(A) 20mm thick. (12.3.2)

(B) 12 mm thick (12.3.3)

6 mm thick cement plaster to ceiling of mix 1:3 (1 cement :3 fine sand). (12.5)

(7.14) Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).

(7.15) Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).

(11.18.2) Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)For area of each slab from 2001 to 5000 Sq.Cm

(11.19.1) Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete For area of each slab upto 2001 Sqcm

(9.39) Providing and fixing of double leaf steel shutter for cupboard the frame is made of pressed steel ISI section 80x25 mm x 1.25 mm thick with 1.00 mm MS sheet to spot welded includig holdfast of 15 x 3 mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direciton of Engineer in charge.

12.45.1 Applying priming coat : With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood.

(12.46.1) Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

(12.22.1) Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats)

(12.37.1) Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats) over and including scrapping and priming coat with cement primer.

(12.42) Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ).

(12.20) Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per approved design

(12.19) Making grooves as per design in plaster 10mm to 20mm wide.

(11.3.1) Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of NOSing of steps etc. complete.40mm thick with 20mm thick nominal size aggregate.

(R/4.9) Providing, laying spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (pug mill), carriage of mixed material by tipper to site, laying in uniform layers in sub base/base course on a well prepared sub base and compacting with smooth wheel roller of 80 to 100 KN weight to achive the desired density including lighting, barricading and maintenance of diversion, etc as per table 400.11 & 400.12 and MoRD specification clause 406. By mechanical means with 1 km lead.

R/6.7 (iii) (a) P & l of Interlocking M-30 grade concrete Block pavements having thickness 80 mm as per drawings & MoRD Specification Clause 1504 with M-30 Grade 0.30 Mtr X 0.30 Mtr X 0.15 Mtr Edge Blocks. Category 'A' Dentated units to key into each other on all four faces zigzag shape as per IRC: SP:63-2004.

(1.2.2) P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor:Size 580x440mm.

(1.14.1) P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.Flat Back (small) size 456x355x265mm.

1.36.4 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 580 mm x 450 mm

P & F Towel Rail or Ring of approved quality/make (a) C.P. brass towel rail with brackets 600 x 20mm. (1.47.4):

2.26.2/S-2 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 300 ltr capacity

P & F looking Mirrors with P.V.C. frame of approved (Atul, Modi Guard, Saint Gobin or equivalent).Size 500 x 400 mm. (1.45.1)

P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: (Exposed on wall) (a)15 mm dia nominal bore'B' Class (2.1.1)

(B)25 mm dia nominal bore'B' Class (2.1.3)

2.2.1, 2.2.3 P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. (a)15mm dia nominal bore B- Class

(b)25mm dia nominal bore B- Class

2.3.1/S-1 Making connection of G.I. distribution branch with G.I. main including all fittings.upto 25mm dia.

2.7.3 /S-2 P & F Bib cock (IS: 8931 Mark), Superior quality of approved make: (A) C.P. brass bib cock 15mm nominal bore.

(2.11.1) P&F Ball Cock (IS:1703 Mark) with Rod & P.V.C. Ball complete:Brass wt. not less than 300 grm, 15mm.

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : (a)Gun-metal 15mm nominal bore.(2.15.1)

(B)Gun-metal 25mm nominal bore.(2.15.3)

(2.14.9) P & F Flush Cock/Flush Valve(IS : 9758 Mark) for WC ofapproved quality make : Brass/Gun metal Half-turn wt. 1 Kg. of approved quality/make, 25mm nominal bore.

(2.12.1) P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc.C.P. Inlet connection 15mm.Brass (IS : 8931 marked)

P & F 15 mm. Dia Connection Pipe of approved quality/make : (a) PVC pipe with C.P. Brass nuts upto length, 300mm(2.13.1)

(3.19.1) Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth up to 0.5 M

(3.22.3) Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: Size 240 Cm. dia outside & 240 Cm. depth.

(3.27.1) Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 NOS stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 200x100x130 cm.(for 10 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect.

(3.3.1) Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) upto haunches of S.W. pipes including 150 mm thick bed concrete as per Rajasthan PWD specifications (Width W= Dia of pipe in Cm+ 30Cm.) concrete width to be reduced from width W at center of pipe to `0` at top of pipe. 100mm dia S.W. pipe

(3.16.2 , 3.16.3) P & F rigid PVC Pipe (IS : 4985 mark) class II / (4 Kg. / Cm2 .) approved quality / make including joining the pipe with solvent cement rubber ring and lubricant. (a)75 mm dia

(b)110 mm dia

P & F rigid pvc pipe fittings (IS : 4985 mark) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant :110 mm dia.(A) Bend 45˚ (3.17.8.ii)

(B) Bend 87.5˚ .(3.17.9.ii)

(C) Vent Cowel (3.17.12.ii)

(D) Gully trap (3.17.27)

Supply & Fixing G.I. Union ISI marked in G.I pipes line as required complete in all respect of size . (A)15 mm dia nominal bore 'B' Class. (2.32.1)

(B)25 mm dia nominal bore 'B' Class. (2.32.3)

P & F Grating of approved quality/ make Stainless steel sheet size 125 mm dia. (1.48.1)

(1.38.9.1) 1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling. Overall size 18 x 16 x 6 (inches) Bowl size 16x14x6 (inches)

(E020101,E020102,E020103) Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's accessories, round tiles,18 SWG M.S. box with earth terminal, 6 A switch, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required.group2 (a) Short point (up to 3 mtr.)

(b)Medium point (up to 6 mtr.)

© Long point (up to 10 mtr.)

(E020301) Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's accessories, 18 SWG 175 mm x 100 mm x 60 mm M.S. box with earth terminal, 6 A switch, 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required.on board. group2

(E040500) Supplying and fixing of power plug point accessories on 18 SWG metal box of size 175 x 100 x 60 mm. on surface or in recessed with suitable size phenolic laminated sheet cover including cost of 6 pin 16 amp. Switch and socket outlet , making connection , testing , etc. as required.Group2

(E040108), (E040117) Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. Group2 (a) 2 x 2.5 sq. mm. + 1x1.5sqmm

(b) 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

E150705 S & Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 8 SWG G.I. Hot dipped Wire

(E150200) Plate Earthing as per IS:3043 with G.I. Earth plate of size 600mm x600mm x6.0mm by embodying 3 to 4 mtr. below the ground level with 25 mm dia G.I. 'B' class watering pipe including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and C.C. finished chamber covered with hinged type with loking arrangement C.I. Cover, C.I. Frame of size 300mmx300mm and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance as required.

P & F of IP 20 LED tubelight 20 Watt with external batten made from CRCA sheet steel suitable to replace T-8 /T-12 tube light, integral driver, 2000 Lumens + 5% tolerance system lumen efficiency of 100 Lm/Watt minimum expected lifetime of 25000 burning hours, CCT 5700 K, ANSI, CRI 80, driver efficiency > 85% life expectancy of driver min 30000 hrs. PF 0.95 at full load / 230 volt AC. (E301400)

(E203903) S & F of street light bracket made out from following size of 'B' GI pipe with heavy duty pole clamp, Saddles suitable fastners etc. as required. 32 mm Dia.

E170600 P & F 18swg M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on side .

(E060112) P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections with lugs, testing etc. as required. Group1 Single pole MCB 6 A to 32 A rating

(E060211) P&F 240/415 V isolator conforming to IS:13947-III/ IEC 60947-3 on existing board / sheet including making connections with lugs , testing etc. as required.Group1 Double pole isolator 30 A / 40 A rating

(E060513, E060512) P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with 100 A copper bus bar, shorting link , neutral link, earth link and din bar, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required.Group2 Single door (single phase) (A)8 way

E110103A, E110101A P/l PVC / XLPE insulated & PVC sheathed cable of 1.1KV grade with aluminium conductor of IS:1554 P-I / IS:7098 P-I of Group 1 of approved make in ground as perIS:1255 including excavation of 30cmx75cm size trench, 25cm thick under layer of sand, Iind class bricks covering refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. (A) 6.0sqmm 2core. ARM.

(B) 2.5 sqmm 2core. ARM.

"P & F IP-65 protected LED street light luminaire on existing bracket . Fixture made of powder coated single piece pressure die cast alluminium with heat disscipation fins on housing with UV Stablized PC/Toughened glass cover (from 45 Watt onwards ) and should be secondary lens on each LED - The system level luminare efficiency >= 100 with high power LED's of CREE/ NICHIA/ OSRAM/ PHILIPS/ SEOUL make is to be used . The LED driver shall be BIS certified and Input Voltage AC 110 to 270 V AC with input frequency50Hz+- 3% Power factor > 0.95 driver efficiency >85%, TIID (1) < 10%. Humidity 10% to 90% RH working Temp -20C to 50C. Life Expectancy equal or more than 50000 burning hrs with minimum 70% initial lumens maintained , Rendering index > 75% , Surge protection shall be min >= 5 KV internal and min 10 KV external. Manufactures word Mark / Name Engraved / Emborsedd on die cast housing to allow traceability / authenticity till life of fixture . Fixture shall be CE complianed. (A) LED street light fixture 90 WATT. (E304407)"

(B) LED street light fixture 20 WATT (E304401)

(E210101) S & E of PCC /RCC pole as per REC manual No. 15/1979 conforming to IS:2905/1996 including excavation of pit & back filling with stone aggregate / boulders & soil in 0.45 mtr. Consolidating each deposited layers of 0.45mtr. By ramming & watering etc. complete in all respect. 8.0 mtr. long as per Discome specification.

(E071400) P & F IS:371 marked 6 amp surface type ceiling rose including making connection testing etc. as required. Group 2

(E071500) P & F ISI marked 6 amp bakelite batten/angle holder including making connection testing etc. as required. Group2

E072200 P & F ISI marked socket size flush type 120/280 watt rotary 5 step fan regulator including making connection testing etc. as required. Group -I

E301500 P&F 1200 mm sweep BEE 5 Star rated double ball bearing capacitor start aluminium body and blade ceiling fan complying to IS 374 :1979, IP 50 watt at max speed and 320 volt, air delivery > 210 cmm, speed > 330 RPM With down rod upto 30cm with 3x1.5 sqmm PVC insulated flexible copper conductor making connection testing etc as required.

(4.3.2) Const. of Tube- well from ground level & upto 100 Meter depth and above to accommodate housing & assembly pipe of following sizes in all type of alluviium strata by percussion / rotary drilling method & with gravel as per as per IS:4097-1967 & packing as per IS : 2800 (Part - I & II) 1979 as amended upto date (the work includes the cost of gravel & its primary packing & packing during development, lowering of housing & strainer assembly pipes, with supply & wrapping of coir-rope, wherever necessary, for arresting fine sand particles. The work will notinclude cost of housing pipe & strainer pipe assembly & development work, but work would be completed after obtaining sand free water). 200 mm dia. Nominal bore.

(4.2.3) Const. of Tube- well upto 100 Meter depth and above in all type of Rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part - I & II) 1979 specifications. The work would be completed after obtaining sand free water.The tube-well should have a throughout bore as per nominal dia of casing pipe.150 mm dia. Nominal bore.

(4.16) S & I of 32 mm dia G.I. pipe medium class IS:1239 marked in 3m length including all accessories and fittings required for installation of hand pump.

(4.9) S & F M.S. clamp, set of 50 × 6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set.

(4.8.4) S & F tube well cover of M.S.sheet (6mm thick) with nuts and boltscomplete for casing size: 200mm dia Nominal bore

(E040605) P/Laying ISI marked PVC insulated submersible cable confirming to IS :694 with flexible copper conductor including making connection etc. as required. 10.0 Sq.mm 3 core flat/ Round.G 2

(4.5.4) Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. 200 mm Nominal bore.

(4.6.2) Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. 200 mm Nominal bore.

(E-260716) SITC of radial / mixed flow submersible motor pump sets ISI marked (IS:8034-1989) of approved make with required accessories including making connection suitable for T.W./ D.C.B./ Open well. The job includes lowering of riser pipe, G.I./ H.D.P.E. pipe with rope, cables, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. 100 mm diameter Submersible pump shall have following HP Rating, phase, Head, minimum Discharge respectively. 3.0 HP, 1-Ø, (69-125)Mtr, (110-33)LPM (Gr I)

(E261311) Supply and fixing of Oil / Air break Starter panel made out of sheet steel powder coated enclosure comprising of over load protection relay, short circuit & single phasing protection, ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. complete in all respect suitable for following rating motors. For single phase Submersible / Monoblock pump 0.5 HP to 3.0 HP (Group - 1)

PART B B/Wall

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measured at a height of 1m above ground level & removal of rubbish upto a distance of 50 Mtr. outside the periphery of the area cleared. (1.31)

E/W in excavation by mechanical means (hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5m in which or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering &ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils. (1.8)

P & L in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering -All work up to plinth level. (A) 1:4:8 ( 1 cement : 4 coarse sand: 8 graded stone aggregate 40mm nominal size.) (3.1.6)

(B) M-15 grade N.Mix ( 1 cement : 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size.) (3.1.2)

RR stone masonry for with hard stone in foundation and plinth in CSM above 30cm thick wall in CM 1:6 (1cement :6 Sand) (6.1.6)

Brick work with F.P.S. brick of class designation 75 in s/s above plinth level upto floor V level in all shapes & sizes in : CM 1:6 (1cement :6 coarse sand). (5.2.2)

P & F precast cement concrete coping 1 :2 : 4 mix 50 mm thick complete as per specification. (3.8)

Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finished. (A) 20mm thick. (12.3.2)

(B) 12mm thick. (12.3.3)

Providing and fixing steel gate, grating and grills made of angles , tees, square bars, flats, or black pipe with holdfast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. (9.8.1)

Structural steel work riveted or bolted in built up sections, trusses and frammed work, including cutting, hosting (height upto 10m), fixing in position and applying a priming coat of approved steel primer all complete. (9.2)

Add extra for Square or Rectangular pillars in S/S brick work upto V storey. Upto 45 cm length & all sides are free. (5.3.1)

Add extra if Square, Rectangular hollow tubelar section are or grill made by flats only. (9.8.2)

P & F rigid pvc pipe (IS : 4985 mark) class II/( 4 kg/cm2) approved quality / make including joining the pipe with solvent cement rubber ring and lubricant:110mm dia. (3.16.3)

Finishing wall with water proffing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: (A) New work (two or more coats applied @ 3.84 kg/ 10 sqm). (12.41.1)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work. (12.46.1)

C & S with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings strap beam, raft, bases of columns etc. (4.9)

Add extra for RR stone masonry with hard stone in Wall upto 30cm & less thickness. (6.3.4)

R/6.7 (iii) (a) P & l of Interlocking M-30 grade concrete Block pavements having thickness 80 mm as per drawings & MoRD Specification Clause 1504 with M-30 Grade 0.30 Mtr X 0.30 Mtr X 0.15 Mtr Edge Blocks. Category 'A' Dentated units to key into each other on all four faces zigzag shape as per IRC: SP:63-2004.

9.38.3 Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size. Welded mesh 25 mmx 25 mm x 2.1 mm

PART- 'C' (NON-BSR ITEMS)

E/W in filling of excavated earth except black cotton soil with watering & compaction of spreaded earth in 15-30cm layers levelled & neatly dressed as per requirement of site & direction of E/I, work includes cost of earth with taxes, loading, unloading, transportation, labour, water & T&P etc. complete with all lead & lift.

P &F sign board as per approved drawing and specification made of M.S sheet of 1.6mm thick of size 1200X900 mm stiffened by flat 20X3mm on both sides all arround the plate & duly framed with 32mm dia medium M.S black pipe fixed on frame of 50mm OD medium pipe ( Vertical post 3600mm, 3000mm above ground level with angle iron hold fast 35X35X5mm with Horizantal member 1500mm to be jointed with flat 40X6mm and post embeded in cement concrete blook M-15 grade of 450X450X750mm size below ground level as directed by E/I. all MS will be stove enameled and both side lettering, figuring and border on sheet with ready mix synthetic enamelled paint of superior quality in required shade and colour etc. complete in all respect all support framed post & steel tubes will be painted with primer and two coats of enamel paint as per specification & Direction of E/I. Over all size 1500 X 1200mm.

Supply and spreading of crusher dust free of organic matter including stacking spreading and laying in yard as per standard specification including all lead and lift, Transportation, labour, loading unloading, T&P required for spreading of crusher dust work as per direction of Engineer in Charge including dressing ground upto 15cm depth.

S, S & S of graded crusher brocken hard stone aggregate free from organic matter including stacking & spreading in yard / trenches as per the standard specification of size 40mm to 63mm incl. all lead & lift, transportation, labour, loading, unloading & require for graveling work as per direction if Engineer in charge incl. dressing & levelling.

P & F four No. 10ltr. Capacity steel bucket & filling of bucket by sand & appropriate size of steel stand for fixing the steel bucket. The stand made by 65x65x 6mm M.S. angle with two or more coats of enamel paint including primer coat of all buckets & stand including all material labour T&P and other required accessaries. The size & shape of bucket & stand (Length of 2No vertical posts 1.50 mtr. length each, 2 No. horizontal member length 0.90 mtr each & hold fast 2 No. 0.15 mtr each including E/W & duly grouted in CC 1:2:4 (2x30x30x45 cm ) as per direction of Engineer in charge including painting with primer & postman red colour paint and letter writting "FIRE".

Supply of steel office table having top of 19mm thick laminated particle board of size 5'x2' having frame size 25x25mm square hollow pipe MS Pipe thickness 1.6mm frame size 4'10"x 1'10" x 2'6" (750mm hieght) duly welded, grinding and fine finished, fitted with two no MS box each having three drawers, openable opposite side with locking arangement and handle as per fitting arrangement dully coated with steel primer (two or more coats) and painted with powder coated paint

Supply of chair having frame of 19mm round pipe of (16 gauge) and having seat and back of 18 gauge perforated steel sheet of 16"x16" and 16"x8" (semicircular) respectively and dully painting with powder coating paint . (Size of chair LxBxH= 20"x18"x33")

(J) Material to be retrieved

33KV works

ACSR Dog conductor

11KV 45KN Porcelain disc insulator - B&S Type

Hardware for B&S type disc insulator

33KV Pin

33KV Pin insulator

33KV Cross arm with clamp

11KV works

ACSR Weasel conductor

11KV 45KN Porcelain disc insulator - T&C Type

Hardware for T&C type disc nsulator

11KV 45KN Porcelain disc insulator - B&S Type

11KV Pin

11KV Pin insulator

11KV Cross arm with clamp

11KV Top hamper and clamp

Single phase distribution transformers

6.35/0.24 KV substation structure for Single phase distribution transformers

LT Works

AB Cable 1CX25+25 SQ. MM

AB Cable 3CX16+25 SQ. MM

AB Cable 3CX25+25 SQ. MM

AB Cable 3CX50+35 SQ. MM

LT Cross arm 2 feet

Suspension clamp for AB Cable

Lumino Industries Limited

UBITECH PVT LTD