Construction of New (Ten storied plus two basement of parking) Office Building for Establishment under the Commissioner of Taxes, Assam, Dispur, Guwahati-6-(Furnitures Work)

Amount

Providing, supplying and fixing in place COMMISIONER TABLE SIGNATURE SERIES CABIN TABLE - GLASS TOP MAIN TABLE: 2300W X 1000D X 750HT TABLE TOP - 1 no SIDE TABLE: 1300D X 550D X 750HT - 1 no Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping WITH GLASS TOP.Support: 25mm thick pre laminated particle board with 2mm PVC edge lipping & 3 equal drawer pedetal with aluminium die cast arms. Modesty Panel: 18mm thk pre lam board with 2mm PVC edge lipping of 450mm Ht.Wire Management: Slide connector. MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place in place COMMISIONER SIGNATURE SERIES Back Storage with Glass Top: Size : BACK STORAGE: 1500W X 600D X 750HT Table Top: 25mm thick pre laminated particle board with 2mm PVC edge lipping. Sides: 25mm thick pre laminated particle board with 2mm PVC edge lipping Back: 25mm thick pre laminated particle board with 2mm PVC edge lipping with aluminium die cast arms Shutters: 25mm thick pre laminated particle board with 2mm PVC edge lipping with brush steel handles and softclose drawer slides and hinges. MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place COMMISIONER CHAIR Model: Pinnacle Leather Chair Type: Central Tilt/Push Back/Knee Tilt Synchronic/Central Tilt Synchronic/Only Revolving without Tilting Mechanism With Tilt Tension Adjustment, Arm Type Adjustable, 3D Armrest with Height,Angle,Forward & Backward Adjustment Arm Material: Plastic sheel with Aluminum support frame, PU Armpad Overall Chair Height ( Minimum)(Mm): 1140mm Seat Height (Minimum)(Mm): 455mm Backrest Height(Mm): 510-560mm Backrest Width(Mm): 520mm Seat Width(Mm): 520mm Seat Depth(Mm): 400-460mm Aluminium Die Cast with PU Caster Wheels Minimum 5 Nos, of 65 mm Size Ergonomic Seat Design Two section backrest with Height adjustment Material Of Fabric Of Seat and Back Cover: EHS-HAM (100% Polyester) EHS-HAL (Genuine top grain leather) MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place COMMISIONER VISITOR'S CHAIR Model: FP Invention VA: Chrome Base: The frame is made out of 25.4mm tube of 16 gauge tube confirming to IS-7138-1973, Welded by Co2 welding process for uniform surface finish and higher tensile strength perforation on the sheet is of uniform 2.5mm dimension and gives good ventilation. Seating Structure: Seat is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood . Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. T Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Back: Cushioned Back with Leatherette Upholstery. Adjustable Lumbar Support Allows you to adjust the lumbar support position for good back support and blood circulation Armrest :Moulded self skinned polyurethene Arms confirming to IS 7078 with steel inserts for long life - Fixed Arms Leatherette: Seat & Back are duly upholstered with High Grade Leatherette MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place COMMISIONER SOFA Model: Barister MADE OFF : NEEM WOOD FRAME, SUPPORTED BY HIGH QUALITY OF WEBBING BELT, 40/32/40 DENSITY FOAM USED FOR UPHOLSTERY, 2” FOAM ARE USED ON TOP OF SEAT, FOR BETTER SUPPORT AND EXTRA COMFORT, ALL HARDWARE – USED FROM KANGAROO COMPANY (STAPLE PINS/ SOLUTIONS/ NAILS / SCREW-NUTS ETC), FABRIC CAN BE USED OF SF SEREIS FABRIC OR RESPONSE STYLO LEATHERRETE SHADE CARD . (LEGS ARE POWDER COATED GOLD – METAL LEGS) 2 Seater: 1610 x 975 x 820 H MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place COMMISIONER SOFA Model: Barister MADE OFF : NEEM WOOD FRAME, SUPPORTED BY HIGH QUALITY OF WEBBING BELT, 40/32/40 DENSITY FOAM USED FOR UPHOLSTERY, 2” FOAM ARE USED ON TOP OF SEAT, FOR BETTER SUPPORT AND EXTRA COMFORT, ALL HARDWARE – USED FROM KANGAROO COMPANY (STAPLE PINS/ SOLUTIONS/ NAILS / SCREW-NUTS ETC), FABRIC CAN BE USED OF SF SEREIS FABRIC OR RESPONSE STYLO LEATHERRETE SHADE CARD . (LEGS ARE POWDER COATED GOLD – METAL LEGS) 1 Seater: 980 x 975 x 820 H MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place COMMISIONER CENTER TABLE Model: Stark Coffee Table Size: L 1200 x 600D x 450 mm Ht Wooden coffee table Wooden legs Magazine shelf MAKE: FEATHERLITE or equivalent as directed by the dept. (Commissioner,Commissioner Rest Room, Addl. Commissioner, Addl.Com Rest Room,JCT, DCT, ACT,VIP Waiting, EX 1 2nd Floor(VIP for Auditorium))

Providing, supplying and fixing in place COMMISIONER Side TABLE Model: HobbitTable Size: L 660 x 410D x 460 mm Ht Wooden coffee table Wooden legs Magazine shelf MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place Model: Barister-933 - 3 Seater MADE OFF : NEEM WOOD FRAME, SUPPORTED BY HIGH QUALITY OF WEBBING BELT, 40/32/40 DENSITY FOAM USED FOR UPHOLSTERY, 2” FOAM ARE USED ON TOP OF SEAT, FOR BETTER SUPPORT AND EXTRA COMFORT, ALL HARDWARE – USED FROM KANGAROO COMPANY (STAPLE PINS/ SOLUTIONS/ NAILS / SCREW-NUTS ETC), FABRIC CAN BE USED OF SF SEREIS FABRIC OR RESPONSE STYLO LEATHERRETE SHADE CARD . (LEGS ARE POWDER COATED GOLD – METAL LEGS) Size: 2020 (W) x 975 (D) x 820 (H) MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place ADDL. COMMISIONER TABLE Model: Elite Size: 2200 x 950 x 760 Extention: 1900 x 600 x 620 1.E1 grade particle board with imported "Schattdecor" melamine finish. 2. Fixed side return with 2 drawers, single swing door, open shelf and open space for CPU, with holes for customer put their sockets. 3. Fixed side return 4. Wirebox on table top, with cover for wire entrance only. 5. Unique leg design MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place ADDL. COMMISIONER CHAIR MODEL: LIBERATE HB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as perCastors - Twin Castors 50mm dia castors compling toANSI / BIFMA X 5.1 – 2002 Gaslift: Class 4 tested -ANSI BIFMA performance standardsSeating Structure: Seat and back is made out of 12mm molded hotpressed plywood in ergonomic shape fitted with Imported T-nuts andrevited in to the wood Upholstery: Upholstery: Cushion ith premoulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: Distinctively and characteristically designed tiltmechanism offering a very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat to back recline ratioof 3:7, optimal for good back support.Multilock mechanism is fabricated from Sheets, undergo through CO2 welding processimparting uniform surface finish and tensile Sheets, undergo through CO2 welding process imparting uniform surface finish and strength.The components are processed with high degree of precision and careso as to assemble with other parts in perfect harmony to give smoothand effortless reclining experience. Tension springs are made outGrade II material conforming to Indian Standards. Also provided withrelease levers for locking mechanism and height adjustment of seat.Mechanism aides to operate the height adjustment, and has beenequipped with 4 locking positions, back rest “ Return Prevention”function .The chair back sways sideways along with the body movement. MAKE: FEATHERLITE or equivalent as directed by the dept. Addl. Commissioner, JCT,JCT Conference room

ADDL. COMMISIONER VISITOR'S CHAIR MODEL: CONTACT PROJECT VA Frame The frame is made out of 25.4mm tube of 16 gauge tube confirming to IS-7138-1973, Welded by Co2 welding process for uniform surface finish. Powdercoating: Thermo set powder coating epoxy polyester hybrids of hardness (pencil) H.B.74 and impact resistant (in lab) 60-160 kgs cm and to a thickness of 40-50 microns is carried out of 7 step pretreatment process. Fasteners: High quality metal hardware conforming to Hardness 38-44 and tensile strength – 1300 n/mm. IS 1363-1967 Seating Structure: Seat is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Japanese T-nuts and riveted into the plywood Upholstery: Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Armrest: Polypropylene injection moulded armrests - Fixed Arms Back: Mesh Back on Frame. Fabric : Seat are duly upholstered with approved fabric MAKE: FEATHERLITE or equivalent as directed by the dept.Addl. Commissioner, JCT,Commissioner Conference room, VIP WAITING, ex 1 2ND FLOOR(VIP for auditorium)

Providing, supplying and fixing in place ADDL. COMMISIONER SOFA Model: E007 SOFA MADE OFF SOLID WOOD FRAME, SUPPORTED WITH HIGH CLASS WEBBING BELT, 40/32/40 DENSITY FOAM USED ON SEAT AND BACK, EXTRA 2” FOAM COVERED ON SEAT FOR EXTRA COMFORT, BOTTOM FRAME MADE OF SOLID WOOD AND POLISHED WITH NATURAL WOOD POLISH, LEGS ARE MADE OF METAL AND POWER COATED IN BLACK, SOFA UPHOLSTERY DONE EITHER IN RESPONSE STYLO SHADE CARD OR FEATHERLITE GENESIS FABRIC. 3 Seater: 1930 x 880 x 840 H MAKE: FEATHERLITE or equivalent as directed by the dept. (Addl Com, Addl Com Rest Room, Post function waiting lobby)

Providing, supplying and fixing in placeADDL. COMMISIONER SOFA Model: E007 SOFA MADE OFF SOLID WOOD FRAME, SUPPORTED WITH HIGH CLASS WEBBING BELT, 40/32/40 DENSITY FOAM USED ON SEAT AND BACK, EXTRA 2” FOAM COVERED ON SEAT FOR EXTRA COMFORT, BOTTOM FRAME MADE OF SOLID WOOD AND POLISHED WITH NATURAL WOOD POLISH, LEGS ARE MADE OF METAL AND POWER COATED IN BLACK, SOFA UPHOLSTERY DONE EITHER IN RESPONSE STYLO SHADE CARD OR FEATHERLITE GENESIS FABRIC. 1 Seater: 900 x 880 x 840 H MAKE: FEATHERLITE or equivalent as directed by the dept. Addl. comm, Addl com rest room

Providing, supplying and fixing in place Model: STO 90210 900L X 450D X 2100HT Specification: The storage top 25mm thick, shutter & sides panel are made of 18mm thick & back panle is made of 09mm thick prelaminated particle board of approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping glued with hotmelt Eva glue free from any VOC.with finger groove handle & suitable (no visible handles) lock.All exposed area PVC edge lipping. MAKE: FEATHERLITE or equivalent as directed by the dept. (Addl Com,DCT,ACT,ST,cashier,OS, PA,Head Office)

Providing, supplying and fixing in place Model: STO 90120 900L X 450D X 1200HT Specification: The storage top 25mm thick, shutter & sides panel are made of 18mm thick & back panle is made of 09mm thick prelaminated particle board of approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping glued with hotmelt Eva glue free from any VOC.with finger groove handle & suitable (no visible handles) lock.All exposed area PVC edge lipping. MAKE: FEATHERLITE or equivalent as directed by the dept. (Addl Com,JCT,DCT,ACT,ST,IT, Cashier, issue receive docket, help desk)

Providing, supplying and fixing in place JCT TABLE Model HT 501- A Size: 2200 x 800 x 750 Ht Side Unit: 1010 W x 500 D x 650 H Specification: Material: MDF + particle board of 50 mm thickness. Surface finsish: Melamine Wire manager included. Color: Dark walnut MAKE: FEATHERLITE or equivalent as directed by the dept. JCT Table

Providing, supplying and fixing in place JCT Back Unit Model HT 325 Size: 1800 x 400 D x 2000 H Specification: Material: MDF + particle board of 50 mm thickness. Surface finsish: Melamine Wire manager included. Color: Dark walnut MAKE: FEATHERLITE or equivalent as directed by the dept. JCT Table

Providing, supplying and fixing in place JCT SOFA MODEL: INTERACT - 3 SEATER MADE OFF : THE SOFA IS MADE OF FINE QUALITY LEATHERRITE (3s = 8.0 mtr, 2s = 6.8 mtr, 1s= 5.3 mtr), THE STRUCTURE IS MADE FROM SILVER WOOD & PINE WOOD, 32 & 40 DENSITY FOAM IS USED WHICH IS COVERED WITH ROLL POLY FILLING FOR GIVING COMFORT AND EXTRA SOFTNESS TO SOFA. EXTRA MATERIAL USED FOR 902 SOFA  ELASTIC NEVAR BELT, STAPLER PINS LEGS : ARE MADE OF STAINLESS STEEL SIZE : 1800 W X 710 D X 780 H  3 SEATER MAKE: FEATHERLITE or equivalent as directed by the dept. JCT,JCT Rest Room,EX 1 2nd Floor(VIP for Auditorium)

Providing, supplying and fixing in place JCT SOFA MODEL: INTERACT - 1 SEATER MADE OFF : THE SOFA IS MADE OF FINE QUALITY LEATHERRITE (3s = 8.0 mtr, 2s = 6.8 mtr, 1s= 5.3 mtr), THE STRUCTURE IS MADE FROM SILVER WOOD & PINE WOOD, 32 & 40 DENSITY FOAM IS USED WHICH IS COVERED WITH ROLL POLY FILLING FOR GIVING COMFORT AND EXTRA SOFTNESS TO SOFA. EXTRA MATERIAL USED FOR 902 SOFA  ELASTIC NEVAR BELT, STAPLER PINS LEGS : ARE MADE OF STAINLESS STEEL 750 W X 710 D X 780 H  1 SEATER MAKE: FEATHERLITE or equivalent as directed by the dept.. JCT,EX 1 2ND floor(VIP for auditorium)

Providing, supplying and fixing in place DCT Model: FST MT 21090 Specification: MAIN TABLE: 2100W X 900D X 750HT Side Table: 1500 x 450D x 750 Ht Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Modesty Panel: 18/12mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25mm thick PLT gable end. Wire Management : Grommet Hole provided on table top. Mobile Pedestal Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle(No visible handles) and suitable locks. Trolley for UPS MAKE: FEATHERLITE or equivalent as directed by the dept. DCT

Providing, supplying and fixing in place ST, ACT Model: FST MT 18090 Specification: MAIN TABLE: 1800W X 900D X 750HT Side Table: 1500 x 450D x 750 Ht Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Modesty Panel: 18/12mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25mm thick PLT gable end. Wire Management : Grommet Hole provided on table top. Mobile Pedestal Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle(No visible handles) and suitable locks. Trolley for UPS MAKE: FEATHERLITE or equivalent as directed by the dept. ACT,ST

Providing, supplying and fixing in place DCT, ACT, ST CHAIR MODEL: ASTRO HB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift - Class 4 tested -ANSI BIFMA performance standards Seating Structure: Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 Sheets,The steel components are manufactured with highly precision tools accuracy in matching other parts for smooth functioning. The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile strength. Springs are made out of Grade II material. Composite release levers for locking mechanism & Gas lift height adjustment. Release lever mechanism for Locking and Gas lift height adjustment. Headrest: Adjustable Headrest Back: Back Frame is upholstered with Thinner Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support position for good back support and blood circulation Armrest: Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable.Tension Control : Tension control is below the Seat Fabric: Seat are duly upholstered with approved fabric Make: Featherlite ST,ACT

Providing, supplying and fixing in place DCT, ACT, ST VISITOR'S CHAIR MODEL: SMART VA Legs:Powdercaoted 4 Legs Back: Tinner Mesh Back Seating Structure: Seat is made out of 12mm molded hot pressed plywood in ergonomic shape fitted withImported T - nuts and revited in to the wood Upholstery: Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Back: Moulded Polypropylene back with netted fabric upholstred Armrest: These arms are made out of polypropylene injection molding component which offers the smooth finishes and Scratch resistance. Fixed Arms Fabric: Seat are duly upholstered with approved fabric Make: Featherlite DCT,ACT,ST,IT

Providing, supplying and fixing in place DCT, ACT SOFA SOFA Model: Pearl 238 1 Seater: 780 (W) x 725 (D) X 700 (H) 2 Seater: 1275 (W) x 725 (D) X 700 (H) 3 Seater: 1800 (W) x 725 (D) X 700 (H) MADE OFF: THE SOFA IS MADE FOR FINE QUALITY LEATHERITE (3s = 7 mtr, 2s = 5.5 mtr, 1s= 4.5 mtr), THE STRUCTURE IS MADE FROM SILVER WOOD & PINE WOOD , 32 & 40 DENSITY FOAM IS USED WHICH IS COVERED WITH SOFTY FOAM AND ROLL POLY FILLING FOR GIVING COMFORT AND EXTRA SOFTNESS TO SOFA. EXTRA MATERIAL USED FOR 238 SOFA è ELASTIC NEVAR BELT, STAPLER PINS MAKE: FEATHERLITE or equivalent as directed by the dept. DCT,ACT

Providing, supplying and fixing in place IT TABLE Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cafeteria table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure - Table top is supported on MS Powder coated Square perform Legs which is constructed by 50 x 50 mm Sq-1.6g ERW tube acts as vertical member & supporting MS cross beam, which is made of 40 x 20 x 1.6 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. Wire Management - 70mm thick, 250mm HT Raceway with laminate facia on main spine BTT provided with separator for data and power cables. Grommet Hole and vertebra for wire intake from floor is considered. Mobile Pedestal Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle(No visible handles) and suitable locks. Trolley for UPS MAKE: FEATHERLITE or equivalent as directed by the dept. Model : PER MT 18090 MAIN TABLE: 1800W X 750D X 750HT IT,PA

Providing, supplying and fixing in place IT CHAIRS Model: Contact Project MB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Castors: Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift - Class 4 tested -ANSI BIFMA performance standards Seating Structure: Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with ImportedT-nuts and revited in to the wood Upholstery: Upholstery: Cushion with h pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Synchro Mechanism: This mechanism is manufactured out ofcold Rolled Carbon Steel IS 513-1994 Sheets,The steel components are manufactured with highly precision tools Foraccuracy in matching other parts for smooth functioning. The steel components are fabricated by using Co2 welding processfor giving uniform surface finish with higher tensile strength.Springs are made out of Grade II material. Composite release levers for locking mechanism & Gas lift height adjustment.Release lever mechanism for Locking and Gas lift height adjustment. Tension Control: Tension control is below Seat Armrest: Polypropylene injection moulded armrests - Adjustable Arms Back: Mesh Back on Frames Fabric: Seat are duly upholstered with approved fabric MAKE: FEATHERLITE or equivalent as directed by the dept. IT,AHU Room, Meeting Room 5th Floor, Data Centre

Providing, supplying and fixing in place JR Assistant, Sr Assistant, OS, Help desk TABLE, Assistant, PA, Internal Auditor Model: PER MT 15060 MAIN TABLE: 1500W X 600D X 750HT Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cafeteria table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure - Table top is supported on MS Powder coated Square perform Legs which is constructed by 50 x 50 mm Sq-1.6g ERW tube acts as vertical member & supporting MS cross beam, which is made of 40 x 20 x 1.6 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. Wire Management - 70mm thick, 250mm HT Raceway with laminate facia on main spine BTT provided with separator for data and power cables. Grommet Hole and vertebra for wire intake from floor is considered. Mobile Pedestal Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle(No visible handles) and suitable locks. Trolley for UPS MAKE: FEATHERLITE or equivalent as directed by the dept. gr Floor AHU/CCTV Monitoring, Sr Asstt, Jr Asstt,Cashier, Computer Person/Int Aud, Issue Receipt Docket, Help Desk, OS, Assistant/EPABX

Providing, supplying and fixing in place JR ASSISTANT, SR ASSISTANT, HELP DESK, CASHIER ROOM, PA & ASSISTANT ROOM Model: Smart MB Base: The 630mm dia (25 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Castor: Castors - Twin Castors 50mm dia wheel made of castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift - Class 4 tested -ANSI BIFMA performance standards Seating Structure: Seat is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 Sheets,The steel components are manufactured with highly precision tools For accuracy in matching other parts for smooth functioning. The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile strength. Springs are made out of Grade II material. Composite release levers for locking mechanism & Gas lift height adjustment. Release lever mechanism for Locking and Gas lift height adjustment. Back: Moulded Polypropylene back with netted fabric upholstred Arm rest: These arms are made out of polypropylene injection molding component which offers the smooth finishes and Scratch resistance. Fixed Arms Fabric : Seat are duly upholstered with approved fabric MAKE: FEATHERLITE or equivalent as directed by the dept. Sr Asstt,Jr Asstt, cashier, computer person/int aud/OS/Assistant/PA

Providing, supplying and fixing in place Commissioners Conference ROOM TABLE Model: FST CT 870180 MAIN TABLE: 1800W X 600D X 750HT (1 NO) SIDE TABLE: 1350W X 600D X 750HT (6+6 NOS) Specifications Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Modesty Panel: 18/12mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25mm thick PLT gable end. Wire Management - 300mm Flip is considered on each table with cable dumb and 3nos vertical wire entry cover. MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place CONFERENCE MAIN CHAIR . Model: MODEL: FP OPTIMA HB Base: The 640mm dia (26 inches) five pronged base ismade out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudentlyand rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair StandardsGaslift - Class 4 tested -ANSI BIFMA performancestandards Seat and back is made out of 12mm molded hot pressedplywood in ergonomic shape fitted with Imported T-nutsand revited in to the wood Upholstery: Cushion with pre moulded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Distinctively and characteristically designed tilt mechanismoffering a very smooth and fluidic reclining motion with tension adjust knob and importantly offering seat toback recline ratio of 3:7, optimal for good back support .Multilock mechanism is fabricated from CR Sheets,undergo through CO2 welding process imparting uniform surface finish and tensile strength. Thecomponents are processed with high degree of precision and care so as to assemble with other parts in perfectharmony to give smooth and effortless reclining experience. Tension springs are made out Grade II material conformingto Indian Standards. Also provided with release levers for locking mechanism and height adjustment of seat.Mechanism aides to operate the height adjustment, and has been equipped with 4 locking positions, back rest“ Return Prevention” functionAdjustable Lumbar Support Allows you to adjust the lumbarsupport position for good back support and blood circulation Tension control is below Seat 3 Moulded polyurethene Arms confirming to IS 7078 withsteel inserts for long life. 2 way adjustable - Height & Swivel Adjustable. Seat is duly upholstered with approved with approved Fabric MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place CONFERENCE REVOLVING CHAIR Model: Amaze MB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift - Class 4 tested -ANSI BIFMA performance standards Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: Self Calibrating Multilock Mechansim Tested as per BIFMA Standards. Back Frame is inserted with Mesh & Dynamic Adaptable Lumbar Support Tension control is below the Seat. Armrest: Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable. Fabric: Seat is duly upholstered with approved fabric MAKE: FEATHERLITE or equivalent as directed by the dept. Commissioner conference room, VC Room, JCT Conference room, computer training room

Providing, supplying and fixing in place MEETING TABLE VC ROOM & AHU Rooms Model : FST MT 360120 SIZE: 3600W X 1200D X 750MM HT TABLE TOP Specification: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of meeting table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25mm thick PLT gable end. Modesty Panel: 18mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Wire Management: 300mm Anodised flip up Made of Aluminum in anodised finish, which has soft closure and three way wire acess & PVC cable dump. Vertebra for wire entry. MAKE: FEATHERLITE or equivalent as directed by the dept. VC Room, AHU Rooms

Providing, supplying and fixing in place MEETING TABLE Meeting Room 5th Floor Model : FST MT 300120 SIZE: 3000W X 1200D X 750MM HT TABLE TOP Specification: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of meeting table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25mm thick PLT gable end. Modesty Panel: 18mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Wire Management: 300mm Anodised flip up Made of Aluminum in anodised finish, which has soft closure and three way wire acess & PVC cable dump. Vertebra for wire entry. MAKE: FEATHERLITE or equivalent as directed by the dept. 3rd Floor Advance ruling, meeting room 5th floor

Providing, supplying and fixing in place MEETING CHAIR Model: Amaze HB Base: The 640mm dia (26 inches) five pronged base is made out of GF nylon Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards Castors - Twin Castors 50mm dia castors compling to ANSI / BIFMA X 5.1 – 2002 Gaslift - Class 4 tested -ANSI BIFMA performance standards Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52 kg/m3 Hardness -- 12.6kgf at 25% Mechanism: Self Calibrating Multilock Mechansim Tested as per BIFMA Standards. Back Frame is inserted with Mesh & Dynamic Adaptable Lumbar Support Tension control is below the Seat. Armrest: Moulded polyurethene Arms confirming to IS 7078 with steel inserts for long Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable. Fabric: Seat is duly upholstered with approved fabric MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place JCT Conference ROOM TABLE Model: FST CT 525180 MAIN TABLE: 1800W X 600D X 750HT (2 NOS) SIDE TABLE: 1350W X 600D X 750HT (3+3 NOS) Specifications Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cabin table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Modesty Panel: 18/12mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: 25mm thick PLT gable end. Wire Management - 300mm Flip is considered on each table with cable dumb and 3nos vertical wire entry cover.

Providing, supplying and fixing in place AUDITORIUM CHAIR Model: Click Auditorium Chair FRAME: The Frame is made out of 75x6mm thickness mild steel Flat is Confirming IS – 513:1994. The Frame is welded by Co2 welding process for Uniform finish and high Tensile Strength wire 0.8mm IS:0419-SL frame joints are brazed & neatly Finished. POWDER COATING : The Frame are powder coated with epoxy polyester Hybrids of hardness HB74 and Impact Resistant (IN LAB) and thickness 40 to 60 microns is carried out of 7 steps pre – treatment process.SEAT STRUCTURE & UPHOLSTRY: Seat & Back is made by 12mm Moulded Hot Pressed Plywood in Ergonomic Shape.They are Polyurethane Moulded Foam with Density 50 – 55 in same shape as the plywood, Upholstery is done by using High Pressure Pneumatic Spray Glue and Pneumatic Press and by covering with polypropylene seat cover. ARMS: Arms are made of Rubber wood with Melamine Finish to Size: 50x 300x 25. FASTENERS : High Quality Metal Screws confirming to IS:2269 Hardness HRC 38.44 and Tensile Strength 1300 N/mm square. side Panel/Aisle Panel The chair rests on the ground on two side panels frames made of 2.5mm thk CR steel. Each Side panel is fitted with two upholstered practical board of 9mm thk. The side panel frame is grouted to the floor using foundation expansion bolts through base. SEAT 480x480 mm BACK 620x470 mm SEAT HEIGHT 420 mm OVERALL HEIGHT 950 mm MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in placePost Function Lobby TABLE and Library Table Model: PER 15090 Size: 1500 x 900 x 750 Ht Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cafeteria table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure - Table top is supported on MS Powder coated Square perform Legs which is constructed by 50 x 50 mm Sq-1.6g ERW tube acts as vertical member & supporting MS cross beam, which is made of 40 x 20 x 1.6 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. MAKE: FEATHERLITE or equivalent as directed by the dept. Canteen,post function waiting lobby, library, canteen

Providing, supplying and fixing in place POST FUNCTION LOBBY CHAIR Model Loop Cushion Frame: The Frame is fabricated with special profile ERW tube of 75 mm (W) X 30 (H) mm X 1.6 (T) mm, conforming to IS – 4923. Frame is welded by CO2 welding process for uniform finish conforming to IS 816. Legs are fitted to aluminium die caster of 250 mm (L) X 39 mm (W) X 55 mm (H) conforming to JIS H 5302. Surface finish : Frame is powder coated to provide an attractive finish. It will be in Grey colour. The powder coating pre-treatment is carried out with three in one chemical. After pre-treatment process, the components are powder coated for better adhesion of paint. The frames are powder coated with epoxy polyester powder to the thickness of 40-60 microns as per IS 101 and oven baked at 180°. Product undergoes the following testing process for durability and functionality, cross cut test for ensuring adhesion of powder coating as per IS 13871. Powder coated products are durable & reduce the risk of scratches, chipping, abrasions, corrosion, fading and other wear issues. Seat & Back shell : Chair is molded with PP 20% GF conforming to ASTM D 638 STD & complying to ROHS compliance. Seat & back are integrated as a single product. Cushioned seat and back It is designed ergonomically to provide comfort to the user. Seat upholstery is carried out with “U” foam and imported SF series fabric, material Polyester & viscose- 380 GLM, Abrasion- > 45000 cycles. No flaming or progressive smouldering within one hour of placement of the cigarettes. MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place BOOK RACK Model: Guide Book Rack Upright - MS 40 x 40 x 1.6 Tube. Side Profile - MS Powder coated metal profile of 1.6mm with Acrylic pouch. Band : Made of MS Powder coated metal 1.6mm Shelves - Made of MS powder coated metal 1.2mm, supported with brackets. Back Panel - Made of MS Powder coted metal 0.8mm. Top panel , Side Panel & Bottom Panle - Made of 18mm thk PLT.Note - If Starter + Addon End Unit is brought together then multiple Addon Center units can be added Later If only Standalone unit is Brought then addon unit cannot be added later MAKE: FEATHERLITE or equivalent as directed by the dept. Starter Size: 1095 x 370 x 1950 Ht

Providing, supplying and fixing in place BOOK RACK Model: Guide Book Rack Upright - MS 40 x 40 x 1.6 Tube. Side Profile - MS Powder coated metal profile of 1.6mm with Acrylic pouch. Band : Made of MS Powder coated metal 1.6mm Shelves - Made of MS powder coated metal 1.2mm, supported with brackets. Back Panel - Made of MS Powder coted metal 0.8mm. Top panel , Side Panel & Bottom Panle - Made of 18mm thk PLT.Note - If Starter + Addon End Unit is brought together then multiple Addon Center units can be added Later If only Standalone unit is Brought then addon unit cannot be added later MAKE: FEATHERLITE or equivalent as directed by the dept. Starter Add on Size: 900 x 370 x 1950 HT

Providing, supplying and fixing in place COMPUTER TRAINING TABLE Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cafeteria table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure - Table top is supported on MS Powder coated Square perform Legs which is constructed by 50 x 50 mm Sq-1.6g ERW tube acts as vertical member & supporting MS cross beam, which is made of 40 x 20 x 1.6 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. Wire Management - 70mm thick, 250mm HT Raceway with laminate facia on main spine BTT & Grommet Hole is considered. and vertebra for wire intake from floor. MAKE: FEATHERLITE or equivalent as directed by the dept. Model : PET TT 19560 Size: 1950 x 600 x 750 Ht (3 Seater)

Providing, supplying and fixing in place COMPUTER TRAINING TABLE Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cafeteria table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure - Table top is supported on MS Powder coated Square perform Legs which is constructed by 50 x 50 mm Sq-1.6g ERW tube acts as vertical member & supporting MS cross beam, which is made of 40 x 20 x 1.6 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. Wire Management - 70mm thick, 250mm HT Raceway with laminate facia on main spine BTT & Grommet Hole is considered. and vertebra for wire intake from floor. MAKE: FEATHERLITE or equivalent as directed by the dept. Model : PET TT 24060 Size : 2400 x 600 x 750 Ht (3 Seater)

Providing, supplying and fixing in place COMPUTER TRAINING TABLE Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of cafeteria table surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure - Table top is supported on MS Powder coated Square perform Legs which is constructed by 50 x 50 mm Sq-1.6g ERW tube acts as vertical member & supporting MS cross beam, which is made of 40 x 20 x 1.6 gauge rectangular tube and connected to legs with aluminium die cast wing connectors. Wire Management - 70mm thick, 250mm HT Raceway with laminate facia on main spine BTT & Grommet Hole is considered. and vertebra for wire intake from floor. MAKE: FEATHERLITE or equivalent as directed by the dept. Model : PET TT 30060 3000 x 600 x 750 Ht (4 Seater)

Providing, supplying and fixing in place CANTEEN CHAIR Model: Tang RM : Pre colored PP+GF20% ( 20% short glass fibre reinforced polypropylene) Make : Injection molding Color – 6 colors (Black, white, Orange, Red, Green & Grey) Chair size : 568x487x811 mm Chair weight : 4Kg MAKE: FEATHERLITE or equivalent as directed by the dept. help desk,canteen,staff rest room/peons

Providing, supplying and fixing in place 3 SEATER METAL TANDEM Model: Bruney Metal 7-A Bruney Three Seater Perforated Metal Tandem with Fixed Arms Size : L 1980 x D 690 x H 825 mm Tubular Steel Frame:- a. Frames are made out of ERW tube conforming to IS 3074 and 7138 of 1973. Frames are made out of Dia 50 x 1.5 mm wall thickness. b. Arms are made out of ERW Oval tubes of size 48 x 22 x 1.6mm wall thickness. Seat & Back: a. Frames are made out of ERW Tube Dia 16 x 1.2mm wall thickness. b. Seat and back are made out of CRCA 1.6mm thickness duly perforated. c. Brazing and welding : All the frames joints are brazed and finished. d. Seat and back are welded by Co2 welding process for uniform surface finish and higher tensile strength. Wire specification: IS 6419-197 54 DIN SG2 DIN 8559. Powder Coating: Pre treatment : i.e., degrease, de-rust and phosphate prior to powder coating. Thermoset powder coating by applying epoxy hybrids. Property & Range Hardness (pencil) / HB – 7H, Impact Resistance (in labs) / 60 – 160 Gloss ( 60 degree meter ) / 11 – 18% Colour – salt spray / 1000 hrs. minimum cure range. (Type 2 MLL) (0.05mm) / 3 min. @ 450 F (232 D) Film – time at metal Tem / 25 min @ 220 – 250 F (121 c). Thickness of powder coating 45 to 50 Microns. Elasticity : 3 to 6mm (ASTM D 522 ) Don 5312. Epoxy barger ultra coat is used which is manufactured in collaboration with world leader NV of Holland and Hoechst AG, Germany adhering to international standards. Nickel chromium plated decorative knobs: All the knobs prior to chrome plating are degreased, de-rust. Nickel plating is carried out on Nickel Sulphate bath at 600 degree C temperature with Continuous air agitation and filtration at a current of 4 Amps / sq.ft. Chrome plating done on Chloric Acid bath at 45 degree C current of 15 Amps/Dim2 Frame height adjustable Knob: are made out of modified PCL synomate ABS/PC alloy grade M – 850 jet Block. HardWard : Hard ware items conforming IS 6101 OF UNBRECO / TVS. Three seater (Tandem) chair can be sent in knock down condition and can be assembled at site MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place 3 SEATER CUSHION TANDEM Model: Loop 3 seater tandem * With Arms & With seat cushion * Aluminium side legs with cross beam in grey PC Designed for group and public seating, the Featherlite Tandem series is a fine articulation of practicality of purpose, and durability. These fixed chairs are engineered to make a seating space welcoming. They are built-in sturdy, medium-back variants that can keep users comfortably seated during waiting hours. These chairs are great for visitors’ lobbies in private offices and seating in public places such as airports, train stations, and health and wellness sectors. MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in place POST FUNCTION LOBBY CENTER TABLE WALLNUT RECTANGULAR CENTRE TABLE TABLE WITH 18 MM PLB TOP AND PC SWAGE LEG SIZE: 1050W X 525D X 450HT MAKE: FEATHERLITE or equivalent as directed by the dept.

Providing, supplying and fixing in placePOST FUNCTION LOBBY CORNER TABLE WALLNUT CORNER TABLE TABLE WITH 18 MM PLB TOP AND PC SWAGE LEG SIZE: 600W X 450D X 450HT MAKE: FEATHERLITE or equivalent as directed by the dept.