Construction of Yatri Niwas (Shed) Building At- Satbahini Tirth Sthal, Kandi, Block kandi, Dist- Garhwa

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying in position cememt concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level 1:2:4 (1cement:2coarse sand (zone-111): 4 grade stone aggregate 20 mm nominal size)

Providing and laying in position cememt concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level 1:3:6 (1cement:3coarse sand (zone-111): 6 grade stone aggregate 20 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of cemtring , shuttering and finishing . 1:1/2:3 (1 C ement 1/2 Coarse Sand (Zone III): 3 graded stone agreggate 20 mm nominal size

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying in position cememt concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level 1:1.5:3 (1cement:1.5coarse sand (zone-111):3grade stone aggregate 20 mm nominal size)

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing Designation 100A 112 mm thick reinforced B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:4) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including the cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Reinforced cement concrete work in beams, suspended floors, roof having slope up to 15 landings, balconies, shelves, chajja, lintels, bands, Plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding the cost of centring, shuttering, finishing and reinforcement, with 1:1:5:3 (1 cement: 1.5 coarse sand (Zone - III) : 3 graded stone aggeragate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached plasters, buttresses, plinth and string courses, fillets, column, pillars,piers, abutments, posts and struts etc. above plinth level up to floor five level, xcluding cost of centering, shuttering, finishin and reinforcement

Providing Tor steel reinforcement of 8 mm dia rods & 10mm. ,12mm & 16mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

steel of 8 mm dia

Steel of 12 mm dia

10 mm dia

Steel of 16 mm

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Labour for laying, NP2 R.C.C spun pipe with coiiars in lines level and grade and providing approved jointing materials and joints properly filled to make them lead, proof including providing sight (150mm dia spun pipe)

Supplying of 150 mm dia NP2 hume pipe --do-- all complete E/I

Labour for laying, NP2 R.C.C spun pipe with coiiars in lines level and grade and providing approved jointing materials and joints properly filled to make them lead, proof including providing sight (150mm dia spun pipe)

Supplying of 250 mm dia NP2 hume pipe --do-- all complete E/I

HYDT: Cost of Drilling 200 mm x 165mm 125 meter deep bore well in all kinds of soil and rock in Rural area for installation of pumps set with Hydraulic DTH Rin machine all complete including supplying all materiuals tools, drilling rig. Air Compressor and Equipments as well as fuel lubricants and cost of TRransportation of Rig Machine and other Vechile up to site (i) From 0.0M to 50.0 M

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all omplete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in- charge.

Making 6x6mm grooves in plaster surface over walls truely horizontal or verical as specified at regular intervals, at all heights including cleaning, finishing scaffoding and curing with all leads and lifts of water all complete as per building specification and direction of E/l.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.

Providing and applying plaster of paris (POP) putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer.

Supplying, fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections f approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling C.P brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing paneling and dash fastners to be padi for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminimum door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc complete as per the architectural drawings and the directions or engineer-in-charge and the directions of engineer-in-charge ( Cost of aluminimum snap beading shall be paid n basic item): 21.3.2 with float glass panes of 5.50 mm thickness

Providing two coats of synthetic enamel paint over a coat of red oxdized paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/i

Providing and laying 20mm thick white makrana marble stone slab flooring of approved quality over 19mm. thick base of lime mortar (1:1:1) ( Lime putty : surkhi: coarse sand ) laid and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 6mm precast SEMI GLAZED CERAMIC TILES of approved quality in DADO over 12 mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I with Commercial grade white 15cmx15cm tiles

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement comound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green, Overlaps ofjoints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of sluurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air

Covering of treated surface with PCC :- Providing 25 mm PCC thick Cement Concrete M20 (1:1:5:3) maintaining slopein alternate 2 mt x 2 mt panels with approved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position , striking curing, taxes and royalty all complete as per building specification and direction of E/I. Panels that has been left should be casted next day. There should be 6mm gap betsween panels. Brand Sika_Plastocrate Plus, MYK Proof WP10 , Fosroc - conplast X 421 ic.DR. Fixit Pidiproof LW+

Providing and filling 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealent ( Poring grades) as per drawings and technical specifications and direction of E/I (with 18% GST) Brand : Sika- Polyshulphide, Fasroc-Thieoflex 600, Dr. Fixit Pidiseal PS (42P)MYK Seal, PS of EQuivalent

Point wiring in PVC conduit, with modular type switch: Wiring for light point/fan point/ exahust fan point/callbellpoint with 1.5 sqm mm FRPVC insulated copper conductor single core cable in surfac e/ recessed PVC

S/F Celling rose: Supplying and fixing 2 pin 5 amp celling rose on the existing junction bos/wooden block including connection etc as required

15/16 Watt LED Bulb

1x28 watt T5 tube light fitting

Ceilling fan 48" (1200mm)

12" (300mm) metal exaust fan

Bulk head fitting with 9/10 Watt CFL/LED

ITC fluorescent fitting directly on surface: Installation testing and commissioning of pre wired flourescent fitting/compact fluorescent fiting of all types, complete with all accessories and tube etc directly on celling/wall including connection with

ITC Celling fan: Installation, testing and commissioning of celling fan, including wiring the down rods of standard leanth (up to 30 mm) 1.5 mm RF PV C insulated coppr

ITC exhaust fan upto 450 mm sweep:- Installation of exhaust fan upto 450 mm sweep in the oxisting opening including making the hole suit the size of the above fan making good the damage connection testing commissioning etc as required

S/F Batten Holder: Supplying and fixing battrn/angle holder including connection etc as required

S/F power plug point with piano type accessoires:- Supplying and fixing suitable size G.I box with modular plate cover in front on surface or in recessed including providing and fixing 6 pin 15/16 amps modular socket outlet

S/F rewireable double pole/TP&N switch disconnector:- Providing and fixing following capacity double pole/TP&N sheet metal switc disconnector fusel unit in existing metal board with rewireable tyhpe fuses including drilling holes

32 amps double pole

Twin Control Point Wiring in PVC Conduit,with modular type switch:- Wiring for Twin control light point with 1.5sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit,2 way modular type switch,modular plate,suitable size G.I box etc as required

S/F 'C" Serise MCB:- Supplying and fixing 240 volts "C" series minature circuit breaker suita ble for inductivbe lads of following poles in the existing MCB DB complete with connections testing and

6/32 amps single pole

40 amps DP

S/F S.P MCB DB: Supplying and fixing following way single pole nutral, sheet, MCB distribution board, 240 volts on surface/recess complete with tinned copper busbar , nuturablbusbar, earth bar, din bar, detchable gland plate interconnection phosphate and powder painted

4 way single door

6 way single door

8 way single door

Circuit/Sub main wiring in PVC conduit: Wiring for circuit/sub main wiring along with earth wire with the following size PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required:

2x1.5 sq. mm + 1x1x2.5 sq.mm earth wire

2x2.5 sqmm + 1.252 sq mm earth wire

2x4.0 sq.mm + 1x4.5 sq mm earth wire

2x10 sqmm + 1x10 sqmm earth wire

S/V PVC/G.I boxes :- Supplying and fixing PVC/G.I box of following sizes on surface or in recessed with suitable size of phenolic laminated sheet cover inforont including paintin etc as required

75 mm 75 mm 50 mm deep / (4"x4")

72mm x 146 mm x 48 mm deep / (4"x7")

210 mm x 206 mm x 48 mm deep/ (10"x12")

S/F/ S.P MCB DB: Supplying and fixing following way single pole nutral, sheet, MCB distribution board, 240 volts on surface/recess complete with tinned copper busbar notralbusbar earth bar din bar

4 way Double door

16 wayDouble door

S/F Modular type Electronic Fan Regulator:- Supplying and fixing following modular type electronic Fan Regulator on the existing modular plate and switch box including

Erection on incandescent light fitting :- Erection of Wall Wall bracket/celling fitting of all sizes and shapes containing up to 2 GLS amps per fitting, complete with all accessories including connection etc as required

S/F Mopdular type blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate etc as required

S/F SP MCB blanking plate:- Supplying and fixing Single pole blanking plate nexisting MCB/DB complete etc as required

S/F HRC Fuse Type TP&N switch disconnector :- Providing and fixing following capacity double pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with ISI marked HRC fuses, including drilling holes in

TP&N HRD 200 A

S/F Panel montude changer over:- Providing and fixing following capacity 4 pole panel mounted change over switches in existing cubolle panel board making connectiuon earth

Change over switch 4 Pole 200 A

S/F Busbar Chamber :- Providing and fixing following capacity busb ar chamber with 4 strips of suitable size made of copper heavy duty, complete with all accessories including connections, earthing the body etc as required

Busbar 4 pole 100 A

Busbar 4 pole 200 A

S/F HRC Fuse Type TP&N switch disonnector : Providing and fixing following capacity double ple/TP&N sheet metal switch disconnector fuse unit in existing metal board with ISI

200 A Main Switch TP&N HRC

S/F DP MCB Isolator :- Supplying and fixing following rating, double pole, 240 volts, isolator n the existing MCBDB complete with connections testing

S/F S.P MCB DB:- Supplying and fixing following way single pole nutral, sheet, MCB distribution board, 240 volts on surface/recess, complete with tinned copper busbarm nutralbusbar, earth bar, din bar detachable etc as required (But without MCB/RCCB/Isolator)

4 WAY (4+12) Single door, TPN DB

S/F 'C' Series MCB:- Supplying and fixing , 240 volts 'C' series piniature circuit breaker suitable for inductive bads of followint poles in the existing MCB DB com,plete with connections testing and commisioning etc as required

6/32 amps TPN

S/F rewireable double pole/TP&N switch disonnector: Providing and fixing following capacity double pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable types fuses, including drilling hles metal board, amking connections etc as required 16 A Main Switch DP

S/F HRC fuse type TP&N switch disconnector:- Providing and fixing following capacity double pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with ISI : TP&N HRC 63 A

Cooper earth plate electrode:- Earthing with copper earth plate 600mmx600mmx3mm thick including accessories and providing masonary enclours with cover plate having locking arrangement and

Salt/Coke forplate earth clectrode:- Extra for using salt and coke for G.I or copper plate earth electrode as required

S/L 8 SWG copper wire in ground: Supplying and laying 8SWG copper wire at 0.50 meter below ground level for conductor earth electrode, including soldring as required

S/L 25mmx6mm G.I earth strip in ground : Supplying and laying 25mmx6mm G.I strip at 0.50 meter below grounds as strip earth

P/F G.I lighting conductor final : Providing and fixing of lighting conductor final made of 25 mm dia 300 mm long G.I tube having single prong at top with 85 mm dia 3 mm thick G.I base plate

Reverting sweating and soldring lighting conductor tape:- Reverting sweating and soldring of copper/G.I tape (with another copper/G.I tape base of the final or any another metalic object) as

P/F G.I lighting conductor tape in horizontal run:- Providing and fixing G.I tape 20 mm x 3 mm thick on parapet or surface of wall for lighting conductor complete as required (for horizonal run)

P/F G.I lighting conductor tape in horizontal run:- Providing and fixing G.I tape 20 mm x 3 mm thick on parapet or surface of wall for lighting conductor complete as required (for vertical run)

P/F Testing joint for G.I lighting conductor:- Providing and fixing testing joint 20 mm x 3 mm thick G.I strip 125 mm long, with 4 nos. of tinned brass bolts, nuts, check nuts and spring washers etc. complete as required

P/F G.I earth tape for lighting conductor :- Providing and laying G.I tape 32 mm x 6 mm from earth electrode directly in grounds as required

35 sq. mm 3.5 core for Lift

laying of one nuber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95sq mm direct in ground inculding excavation sand cushioning,protective covering and refilling the trench etc as required

Providing and fixsing Gun metal full way valve of approved quality all complete as per specification and direction of E/I

25 mm dia weight not less than 500 gram

40 mm dia weight not less than 1.0 kg

Cutting chajja or cronice for laying G.I pipe and restoring the same with R.C.C (1:2:4)0 brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of Engineer-in-charge

Making holes in walls for laying G.I Pipes and restoring the same after pipe laying as per specification and direction of E/I

125 mm thick wall

250 mm thick wall

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. With 12.5 lit low level PVC Cistern

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. Flat back or standard corner (600x350mm)

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l.

125 mm thick wall

250 mm thick wall

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (i) single socketed pipes .

75 mm dia

110mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with amps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

25 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per directionof Engineer in Charge.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing PTMT grating of approved quality and colour.

100 mm nominal dia

125 mm nominal dia with 25 mm waste dia

Polythenbe water storage tank of ISI mark (eg sintex/sinter/himgiri/hangotri etc with cover & Locking system

Supply Fitting and Fixing the following items complete with all materials as per specification and direction E/I Miirror of 6mm thick plate glass bevellved edge mirrir inculding C.P brass revolving fitting 3mm ply wood board and C.P hinges to with mirrior (600mmx450mm)

Providing and fixing PVC Pipe fitting with all accessories (Supreme make )

75 mm Coupler

110 mm coupler

110mm Single Pushfit coupler

110 mm Single tee with door

75 mm Single tee with door

110 mm Single tee without door

75 mm single tee without door

75 mm bend

110 mm bend

75 mm shoe

110 mm shoe

C.I. Rectangular cover 455x610 mm with frame (low duty)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mmdiameter, 1.8 m long complete as per standard design.

Carriage of Materials

Sand Lead 10 Km

Stone Chips lead 22Km

Brick Lead 8 Km

Fly Ash Brick 10 km

Stone Metal Lead 22 Km

Add 12 % GST

Add 1% Labour Cess

JITENDRA KUMAR CHATURVEDI

ARVIND TIWARI