Provn of defi parking shed including spl repair to reapps bldg. at Old Cantt Prayagraj and spl repair of OR bathroom at OD Fort Prayagraj and provn of Geyser for JCOs/OR qtr at Naria, Def Enclave at Varanasi Cantt.

Amount

Demolition of brick work or stone/boulders masonry built in cement mortar including all quoins arches pillar etc but excluding Ashlar facing, droved stone work and forecast concrete articles complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level complete all as specified and directed.

M&L for brick work with fly ash bricks(old size), straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for providing Cement concrete in foundations, filling and mass concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) complete all as specified and as directed

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006, 60 mm thickness, M-35 Grade with grey cement and pigment over and including 20mm thick sand cushning complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, staircases, landings and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in slab supported on wall, beams, and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar works complete all as specified and directed.

M&L for Mild steel TMT bars 6 to 8 mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for formwork to soffits of suspended slabs n. exc. 200 mm thick and similar works rough finished surfaces of concrete complete all as specified and directed.

Dismantling stone slabs of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry over and including 15 mm thick screed bed or bedding layer in CM (1:6) , pointed with white cement with admixture of pigment to match the shade of granite stone and grinding & polishing complete all as specified and directed.

Taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces of wall, finishing the surface fair and even complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces of wall, finishing the surface fair and even complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar 1:4 on ceiling surfaces , finishing the surface fair and even complete all as specified and directed.

M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades, selfs lintels etc. and cutting chases for concealed for water tubing or concealed conduit wiring etc and making good, cutting n.exc 10cm girth complete all as specified & as directed

Demolition of existing WPT from roofs, any thickness, including plastering, old water proofing membrane and , concrete padding, copping, leaping, brick/brick tiles etc complete (whether full thickness removed or only a part thereof) and removing the demolished material at a distance n.exc.50 m where directed complete all as specified & as directed

M&L for PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in roof padding in levelling course, benching etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M&L for screed bed 10 mm thick in cement mortar 1:3 over roof slab mixed with water proofing compound as per manufacturer’s instructions finished even & fair complete all as specified and directed. NOTE : WPC will be measured and paid separately as supply only.

Supply only integral water proofing compound complete all as specified & directed.

M&L for Water proofing treatment to the existing roof/ sunken floor surfaces comprising of the following:- (a) Cleaning surface by wire brushes, brooming to remove dust, etc as required. (a) Applying one coat of bitumen primer confirming to IS-3384-1965 @ 0.50 kg per sq.m. (b) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS – 702-1998 before lying waterproofing membrane. (c) Laying 3mm thick APP water proofing membrane( weight not less than 3 kg / sq.m ) over entire area with overlaps and sealed all as specified and directed. (d) Again apply a tack coat of hot blown bitumen 85/25 @ 1.2 kg / sq.m over water proofing membrane. (e) Dusting dry sand @ 0.75 kg per sq.m

Dismantling old unserviceable floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for glazed ceramic coloured tiles 350mmx250 mm x 7mm /450mmX300mm X7mm thick, as in vertical surface such as skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic white tiles 7 to 8 mm thick(square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections, segregating serviceable pipe for reuse complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections, segregating serviceable pipe for reuse complete all as specified and as directed.

S&F 15mm bore medium grade galvanised steel tubes with all fittings and fixed to wall or in floors etc complete all as specified & directed.

S&F 20mm bore medium grade galvanised steel tubes with all fittings and fixed to wall or in floors etc complete all as specified & directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) bedding, connection to trap, outgoing flushing pipe, anti sypohonage pipe,100 mm bore 'P' or 'S' of pipe etc complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pedestal pan white, including 10 ltrs PVC valve less, symphonic action type flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia, Plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed.

M&L for PCC 1:5:10 type E-2 (using 40mm graded crushed stone agg) as in mass concrete in sunken floor complete all as specified & directed.

S&F 100 mm bore Cast Iron ‘P’ or ‘S’ trap complete all as specified & directed.

S&F 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified & directed.

S&F in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets, 32 mm bore PVC flush pipe 600mm long complete all as specified and directed.

S&F in repair Vitreous China counter wash hand basin, oval type, size 570x420x185mm white including necessary fittings complete all as specified and as directed. (Model No.FLS010401 of Jaguar or equivalent from one of the make given in CA)

S&F Brass CP basin mixer for mixing hot & cold water for 15 mm dia, screwed down for iron pipe and fixed complete all as specified and as directed

S&F in repair Vitreous China Urinal, Half stall type, white complete all as specified and directed.

Supply only 32mm dia waste pipe of polythelene, flexible, for wash hand basin or urinals complete all as specified and directed.

S&F in repair fancy type looking mirror, 5mm thick, frame less rounded edge, area n exc 1 sqm each in any shape fix to wall with CP screw and decorative bolt complete all as specified and directed

S&F Flush pipe of polyethylene of low or high density or PVC, 32 mm dia, for low level cistern complete all as specified and directed

S&F in repair grating round/square as suitable 150 mm size with waste hole of PTMT (minimum weight 100 gms) complete all as specified and directed.

S&F in repair bib taps of 15mm bore fancy type, long body, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule all complete as specified and as directed.

S&F in repair 15 mm bore angle valve cast screwed down, high pressure, with crutch or butter fly handle, for iron pipe or for unions complete all as specified and directed.

S&F pillar taps cast copper alloy with capstan heads, chromium plated fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe 15 mm bore fixed in repair complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 65 to 90 mm size with swivel joints, complete all as specified and directed.

S&F in repairs PVC (SWR) pipe 75 dia single socketed in any length with rubber gasket cup washing, jointed fixed to wall complete all as specified and directed.

S&F in repairs PVC (SWR) pipe 75 single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends with access door any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) branch piece, double (double Y), equal or unequal with access door complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints fixed to walls with and including PVC clip complete all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair stop cock of 15mm bore fancy type, chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule complete all as specified and as directed

S& F in repair PVC connections 15 mm size with PTMT, 450 mm length with brass nuts at both ends complete all as specified and directed.

S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed fro iron pipe and fixed for 20mm bore size (minimum weight 210 gms) complete all as specified and directed.

S&F in repair gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and directed.

S&F in repair 100mm bore cast iron (Sand cast pipes) soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed

S&F two way angle valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle for iron pipe or for unions 15 mm bore, fixed in repair complete all as specified and directed.

S&F in repair health faucet (ABS body) with 8mm dia 1.5 meter long flexible tube and wall hook for fixing in 15 mm dia pipe complete all as specified and as directed. (Model No. ALD-CHR-593 of Jaguar or equivalent from one of the make given in CA)

Taking down chowkats or frames with shutter (without taking off shutters from the frames), , area of each opening not exceeding 1.5 Sqm complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) area of each opening exc 1.5 Sqm but n'exc 4.0 sqm complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of Mild Steel tubes for top & bottom rails. Mild Steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the Mild Steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in SSR Part-II 2010 and complete all as specified and directed.

S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed

S&F 4.00 mm thick figured frosted sheet glass ordinary quality and glazing with oil putty or wooden beads in square area not exc. 0.5 Sqm in each pane complete all as specified and directed

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel, 100 mm size type B-21 with galvanised mild steel hinge pin complete all as specified and directed.

S&F 125 mm size aluminium anodised handles, cast type complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 200 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for two coats of cement base paint over a coat of cement primer including preparation of new plastered surfaces of walls complete all as specified and directed.

M&L for two coat of oil bound distemper on newly plastered surface of walls over a coat of primer incl for preparation of surface by applying 1 mm thick wall care putty complete all as specified and directed.

M&L for two coats of white wash on newly plastered surface of ceiling after preparation of new plastered surface complete all as specified & directed.

M&L for preparing old plastered surface of wall and applying one coat of cement base paint complete all as specified and directed.

M&L for complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and applying two coat of oil bound distemper over a coat of (01 mm thick) putty including preparation of surface complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and applying two coat of white wash including preparation of surface complete all as specified and directed.

Surface dressing n exc 15 cm deep in soft/ loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for Mild steel work in tubular trusses, purlins, vertical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and directed.

M&L for Roof trusses (Framed), trussed Purlins, Crane gantries, rails and fastenings and heavy bracket framing (Beam, Tee, angle, Channel or flat section) including distance pieces, cleats etc. Conforming to Fe 410-W-(Gde-E-250) Quality A complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Form work to sides of pillars, posts, rough finished square, rectangular or polygonal surfaces of concrete complete all as specified and directed.

M&L for PCC 1:2 :4 type B1 (using 20 mm graded stone aggregate) as pilasters, buttresses coloumns, pillars, boundary pillars and posts including cap and bases and similar work complete all as specified and directed.

M&L for hard-core broken stone or boulder of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub floors, sub base, floors and pavings etc complete all as specified and directed.

S&F Plastic (PVC) dividing strips, 38 mm wide and 1.5mm thick complete all as specified and directed.

M&L for 100 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floors, finishing the surface even and smooth without using extra cement etc. complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coat of Synthetic enamel paint over a coat of red oxide, primer complete all as specified and directed.

M&L for preparation of new plastered /un plastered surface of walls and applying three coats of white wash complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and averaging 7.5 cm deep and getting out in soft/ loose soil complete all as specified and directed.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

Spreading and levelling excavated earth in layers n exc. 25 cm thick and well ramming including watering as required (below flooring ) complete all as specified and directed.

Taking down carefully aluminum/copper point wiring (light fan socket or power) complete and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified keeping aside serviceable items for reuse with in the same bldg and removing U/S items from site complete all as specified and directed.

Taking down main switches, distribution boards and cut outs of any capacity along with the existing boards and removing the same from site and keeping in safe custody for reuse or issue on credit to contractor and making good disturbed surface or portion of walls, complete all as specified & directed.

Taking down carefully sub main wiring of any numbers of wire on wooden batten or surface conduit or concealed conduits / casing caping any type complete all as specified & directed.

M&L for point wiring for One light/fan/exhaust fan point controlled by one switch in concealed PVC conduit complete including necessary chases cutting with PVC insulated and unsheathed cable 1.5 sqmm (nominal area) multi stranded copper conductor single core and including non metallic concealed PVC conduit not less than 20 mm dia with concealed in wall pressed steel terminal boxes not less than 1.6 mm thick of reqd size (factory made) with top cover 3 mm thick of plastic laminated sheets of required colour painting terminal boxes inside and outside with two coats of block bituminous paint over a coat of red oxide primer complete with all accessories and including PVC insulated and unsheathed cable 1.5 sqmm (nominal area) stranded copper conductor single core of green col our as earth wire to common earth and connected to earth dolly drawn in same concealed conduit incl making good disturbed surfaces and finished to match with existing surface complete all as specified and directed.

All as per item No. 105 above but for One 5 amp socket outlet point on same board with 2.5 Sqmm cable

All as per item No. 105 above but for One 5 amp socket outlet point on independent board with 2.5 Sqmm cable

All as per item No. 105 above but for One bell buzzer point controlled by single pole one way bell push

All as per item No. 105 above but for One 15 amp socket outlet point on independent board with 2.5 Sqmm cable

S&F switch piano, single pole one way 5 Amps 240 Volt complete all as specified and directed.

S&F socket outlet, 2in1, 5/6 amps 5 pin flush type , 230 volts complete all as specified and directed.

S&F switch piano flush button single pole one way 15/16 amps 240 volt complete all as specified and directed.

S&F socket outlet, 2 in 1, 15/16 amps 6 pin flush type , 230 volts complete all as specified and directed.

S&F lamp holder insulated body PVC/ Polycarbonate type with back plate suitable for batten/ angular / pendent holder fittings complete all as specified and directed

S&F ceiling rose three terminals/PVC/polycarbonate, isolated body on PVC board complete all as specified and directed.

S&F Switch, bell push, flush type, 5 amp, complete all as specified and directed.

S&F electric Bell dingdong type, AC 230 volts, 50 Hz, single pole complete all as specified and directed.

S&F Sheet metal enclosure MCB distribution board double door (Acrylic), triple pole and neutral , 415 volts, 4 way 200 Amp rated bus bars & blanking plate wherever required and IP-43 degree protection making necessary electric connections with lugs, complete all as specified & directed.

S&F sheet metal enclosure (MCB distribution board), 8 way single pole & neutral, 240 volts with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note-MCBs will be measured separately.)

S&F MCB TPN, 4 pole, 415 volts, 63 Amps, 'B' curve 10 KA, complete all as specified and directed.

S&F MCB single pole 240 volt any rating from 6 to 32 amps , with rupturing capacity 10 KA , including providing thimble for out going cable complete all as specified and directed.

S&F MCB SPN 240 volt any rating from 6 to 32 amps , with rupturing capacity 10 KA ,including providing thimble for out going cable complete all as specified and directed.

S&F 1 x 9/10 W LED Mirror light fitting, LED 6000K, Decorative Indirect up-down light for mirror and as wall light application with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp complete all as specified and directed.

S&F in repairs for LED tube light fitting 1 x 20 watt, decorative , ultra slim round profile LED lighting fixture with co extruded polycarbonate body , environmental friendly , energy efficient complete with all accessories, prewired and making connection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly complete all as specified and directed.

S&F Recess mounted decorative CRCA LED light fittings of size 2" x 2", 36 Watt LED 6500 K lumen efficiency, high brightness SMD leds, including suitable driver poly carbonate body, environment friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with flexible copper wire, fixed in repairs, complete all as specified & directed. Make : Havells Cat Part No VENUSNEOHE2X2R36WLED840PIRSENSOR or techno-commercially equivalent model in Bajaj or Philips as approved by GE.

S&F 36 Watt road lighting luminaire with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and Streets, 50% Energy Savings, IP66 Protection PC and FG Cover, High Impact Resistance complete including LED Lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20 m long made to shape and fixed to existing pole or bldg by means of 2 Nos mild steel flat iron 40x6mm clamps with suitable size bolt, nuts & washers and connecting with three core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box complete all as specified and directed. Make Philips Cat No BRP409 LED CW 036 MR FG S1 PSU GR or equivalent in Havells/ Bajaj/ Crompton greaves.

M&L for Earthing complete with steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel earth wire protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit made from PCC (1:2:4) type B-1(using 20mm graded stone aggregates) with 17mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25 x 25 x 6mm with lugs 02 No and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom, 1.75 metre long placed on top edge of earth plate, common salt & charcoal filling, test point made out of 17mm x 8mm FI with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No.5 of SSR Part-I connected to earth test point all as specified or indicated including testing on completion, complete all as specified and directed.

All as per item No. 123 above but connecting to the Galvanized iron earth strip made out of 32x6mm flat iron

M&L for sub main wiring with PVC insulated 1100V grade FRLS single core multi stranded copper conductor cable of size 2x4 sqmm + 1x4 sqmm as earth continuity cable passing through and including 25/20mm dia PVC conceal conduit complete all as specified and directed. Note - Two runs of 4sqmm including one run of 4 sqmm including PVC conduit shall be measured as unit length.

Taking down existing ceiling fan/ exhaust fan, any sweep, by disconnecting carefully all electric connection and refixing the same after necessary repair work as required (such as cleaning all the serviceable parts thoroughly, reassembling the fan after testing for proper functioning), with and including provision of electrical wire 3-core 23/0.0076 copper conductor,spray painting with synthetic enamel paint of tint same as that of existing, and wiriting MES No. on fan motor, complete all as specified and directed. NOTE : The quoted rates shall deemed to be inclusive of every minor items i.e., nut, bolts, screws, lugs etc., which are fairly required for the smooth functioning of fans.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one SP MCB 20 A complete all as specified and directed.

Supplying ,laying, commissioning & testing XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor, cross sectional area 50 Sqmm , 3.5 core complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Supplying ,laying, commissioning & testing XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor, cross sectional area 35 Sqmm , 3.5 core complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Supplying ,laying, commissioning & testing XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor, cross sectional area 25 Sqmm , 3.5 core complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

Supply and laying dry well burnt locally available brick sub class 'B' old size bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as specified and directed

M&L Sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand up to 18 cm thick and consolidated complete all as specified and directed. NOTE : Punned thickness only shall be measured.

S&F in repair LED retrofit lamp of capacity 9/10 Watt, B-22 holder base warm white complete all as specified and directed.

S &F for 50 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standing complete all as specified and directed.

S&F electric water heater geyser, storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, 600mm PVC connection pipes etc. complete all as specified and directed.

M&L for Sub main wiring complete with 2 runs of 6 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawing into existing conduit and connecting terminal ends to DB's including providing 1 run of 6 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly and making good disturbed surfaces to match with existing, complete all as specified and directed.

S&F in repair exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm including cutting of suitable hole for exhaust fan and making good disturbed surfaces of walls, floor to match with existing specification complete all as specified and directed.

S & F15 mm dia fancy type chromium plated with long shank and angle valve cast copper alloy screwed down type high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

M/S JAI DURGA CONSTRUCTION

KHALSA BUILDER

vs construction

M/s SKP CONSTRUCTION