Civil Maintenance Work at PRPD Township Anupuram

Amount

Excavating trenches by mannualmeans of required width(0.45m) minimum depth 60 cm for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.00 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m (Pipes, cables etc. Not exceeding 80 mm dia. ) as per specifications and as directed by the Engineer-in-charge

Excavating trenches by mannual means of required width(0.6m) and minimum depth .95 m for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m (Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia) as per specifications and as directed by the Engineer-in-charge

Conveying the surplus excavated earth , debris , boulders and spoil by mechanical means and depositing at places inside township installation identified as dumping yard as per requirement with a lead specified below including loading ,unloading, breaking clods , leveling all complete as per specification and as directed by the Engineer - in- Charge. 1) The rates in respect of this Item are applicable for the NET quantities arrived at after making deductions for the voids @20 % in respect of soil and @50% in respect of Rock from the corresponding Stack/ truck measurements.2) The earth shall be dumped well inside the dumping yard and not over approach pathway road. Lead charges for 1st 1 kilometer or part thereof .

Dismantling Plain Cement Concrete by manually/by mechanical means at all levels, carefully without damaging adjacent structures including disposal of debris with 50m lead, labour, tools required etc. complete in all respects as per specifications and directed by the Engineer-in-charge.

Dismantling of RCC works at all levels by manually/ by mechanical means, including cutting and stacking of steel reinforcement bars and disposal of unserviceable materials within 50m lead as per specification and directed by the Engineer-in-charge.

Dismantling brick work in cement mortar at all levels by manually/ by mechanical means carefully without damaging adjacent structures including stacking of serviceable materials and disposal of unserviceable materials within 50m lead all as per specification and directed by the Engineer-in-charge.

Dismantling tile work ( thickness of tile up to 25 mm) in floors, dado and roofs laid in cement mortar at all levels including stacking material within 50 meters lead complete all as per specifications and as directed by the Engineer-in-Charge.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Providing and laying Plain Cement Concrete (1:4:8 ) using 20 mm maximum size graded aggregates including mechanical mixing, transporting and placing in required position, ramming, compaction leveling, curing, shuttering, dewatering if any, complete all as per specifications for leveling courses in foundation for walls, footings, floor drains etc. encasing pipes and other required works directed by Engineer-in-charge complete all as per specification.

Providing and Making Plinth Protection 50 mm thick of Cement Concrete (1:2:4) 20 mm down graded over 75 mm thick PCC (1:3:6) 20 mm down graded bed well rammed and consolidated and including curing, etc. complete all as per drawings, specifications and as directed by the Engineer-in-Charge.

Supplying of suttering materials, fabricating, erecting and fixing in position at all levels, centering and shuttering to correct line and levels including strutting, propping etc., with necessary bracings in all axes to give a stable assembly with provision for making the joint in the shuttering full leak proof and with provision for fixing coil nuts with tie rods along with suitable channel for lateral supports and for inserts, projecting dowels, anchor bolts or any other fixture, including staging, access and working platforms etc., all complete as specified and directed including dismantling and removing the aforesaid assembly after the concrete attains the sufficient strength to self-support itself without cracking and distortion all as per specification, including all materials and labour complete in all respect at all lifts. The measurement for the formwork will be actual area of forms in contact with concrete surfaces. Shuttering with plywood panels alone will be permitted.

Providing, straightening, decoiling wherever necessary bending , cutting, binding and fixing in position steel reinforcement TMT bars of Fe500D grade steel confirming to IS(1786 : SAIL or VIZAG or approved equal and make) and tying with approved annealed binding wire of 1.6mm dia in all reinforced cement concrete work at all lifts, including cost of supplying and fixing the spacer/ cover blocks in cement mortar 1(2) and binding wire complete all as per specifications and as directed by the Engineer-in-Charge at all lifts. Note (The rate shall be including the cost of reinforcement steel. The reinforcement steel will be procured from dealers with a test certificate as approved by the department. For further details please see clause 11 of section VIII, General information for Guidance of Tenderers.

Providing. Supplying, cutting, bending to shape, welding, fabrication, hoisting, placing and fixing in position structural steel members like trusses Purlin etc. using MS hollow/circular/square/rectangular tubular sections , angles, channels, I-section, plates, tees, flats, rounds, plates etc. including chamfering and rounding off the edges, applying a coat of Red lead paint primer/zinc chromet primer of approved make and 2 coats of flat oil paint /synthetic enamel paint of approved colour and make, scaffolding and staging required for fabrication as well as erection complete all as per specification, drawing and as directed by the Engineer-in-charge. Note : Lifting device arrangements if any required also arranged by the contractor at his own cost.

Providing and laying reinforced cement concrete 1:1.5:3 using 20mm maximum size graded aggregates including mechanical mixing, transporting and placing in required position , ramming, compaction, leveling, curing, dewatering if any, complete all as per specification for leveling courses in foundation for column, walls, footings, floor as per drawings etc., works directed by the Engineer-in-Charge complete all as per specifications.

Providing and constructing brick masonry at all lifts using fly ash bricks in cement mortar 1:5 including suitable scaffolding, racking out joints, curing complete as per specifications and drawings for foundation, superstructure, etc. for the following floors. complete all per specifications and as directed by the Engineer-in-charge.

Providing and constructing at all floors and lifts 115 mm thick brick work in cement mortar 1:4 using fly ash including providing and placing in position 2 nos. of 8 mm dia rods at every 4th layer, scaffolding, curing, racking out the joint on both faces etc. complete all per specifications and as directed by the Engineer-in-charge.

Providing and laying 110mm thick (plus or minus 5mm) brick work with fly ash brick in Cement Mortar 1:4 for solid Compound Wall above ground level with brick on edge coping 230mm wide and 230 x 230mm pillars in Cement Mortar 1:4 at junctions, corners, sides of gate and pillars at every 3 metre intervals and as directed , curing, raking out joints etc. complete at all lifts as per specifications and drawings as directed by Engineer-in-Charge.

Providing and laying 110mm thick (plus or minus 5mm) brick work with fly ash brick in Cement Mortar 1:4 for Honey Comb Compound Wall above ground level with brick on edge coping 230mm wide and 230 x 230mm pillars in Cement Mortar 1:4 at junctions, corners, sides of gate and pillars at every 3 metre intervals and as directed , curing, raking out joints etc. complete as per specifications and drawings as directed by Engineer-in-Charge.

Providing and Plastering to the internal/external surfaces of brickwork/ concrete at all elevations in cement mortar 1:5, 12mm thick including hacking of concrete of surfaces with pointed to, scaffolding finishing, curing, forming grooves wherever necessary, complete as per specifications and drawings as directed by Engineer-in-Charge..

Providing rough cost plastering 20mm thick at all elevation and levels consisting of 8 mm thick rough cast in cement mortar 1:3 using 6mm to 10mm size hard granite stone, over a bed of 12mm thick cement mortar 1:5 for external faces, including scaffolding, curing, providing grooves wherever required complete all as per specifications and drawing and as directed by the Engineer-in-charge.

Providing and Plastering the external surfaces of Brick work/ concrete at all elevations in C.M 1:5, 20 mm thick in two coats including hacking of concrete surfaces with pointed tool, scaffolding, finishing, curing, forming grooves wherever necessary complete all as per specifications and drawings as directed by Engineer-in-Charge.

Providing and water proof plastering cement mortar( 1:4), 20 mm thick at all elevation with 2% of water proofing compound or as per manufacturers specification, Dr. fix it/'lmermo' or approved equivalent make including hacking of concrete surfaces with pointed to, scaffolding finishing, curing etc. complete all as per specifications and drawings as directed by Engineer-in-Charge..

Providing and laying Brick on edge flooring (With available bricks/brick bats) on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks 1:4 (1 cement : 4 coarse sand)

Providing and laying 25 mm thick Indian pattern stone flooring and skirting with cement concrete 1:2:4, using 10mm and below size hard broken granite stone jelly including dividing strips, laying in panels, consolidating, curing, rubbing the surface smooth, cleaning the surface neatly at the time of handing over the area complete all as per specifications and as directed by the Engineer.

Providing & fixing 25mm to 30mm thick one side polished cuddapah stone slab, set in Cement Mortar 1:3, 20mm thick for topping of Kitchen platform and kitchen sink etc. including removing existing damaged Cuddapah stones , labour, pointing the joints, fixing sink waste coupling, curing, complete all as per specifications and drawings as directed by Engineer-in-Charge.. (Note:- Cuddapah stones shall be got approved by the Engineer before making bulk order).

Providing and replacing and fixing 25mm to 30mm thick both side polished cuddapah stone slabs including making grooves in the brickwork and fixing as per the drawing for Shelves in Cupboard/ Wardrobe/ Shoe rack including front face polishing including removing existing damaged Precast Concrete Shelves , labor, materials, tools, scaffolding etc. at all lifts complete all as per specifications and drawings as directed by Engineer-in-Charge..(Note:-Cuddapah stones shall be got approved by the Engineer before making bulk order).

Providing and fixing 1st Quality Ceramic glazed mat finished floor tiles `KAJARIA/ SPARTEK/ ORIENT' or other approved equivalent make, confirming to IS 15622 of approved size, shade and colour (as approved by engineer-in-charge), free from crack, fissures and flakes with straight edges & perfect corners fixed at right angles as per design and pattern required for risers of steps and dados over 20 mm thick bed of cement mortar 1:4), including machine/hand cutting to required size and shape, pointed neatly with white cement mixed with colouring pigment to match color of tile, properly finished in all respects, curing, cleaning the surface neatly at the time of handing over the area, all materials and labour complete. as per specifications and as directed by the Engineer-in-Charge. Note: The sample tile shall be got approved by the Architect/Engineer before procurement.

Providing and fixing 1st Quality Ceramic glazed wall tiles `KAJARIA/ SPARTEK/ ORIENT' or other approved equivalent make, confirming to IS 15622 of approved size, shade and colour (as approved by engineer-in-charge), free from crack, fissures and flakes with straight edges & perfect corners fixed at right angles as per design and pattern required for risers of steps and dados over 12 mm thick bed of cement mortar 1:3), including machine/hand cutting to required size and shape, pointed neatly with white cement mixed with colouring pigment to match color of tile, properly finished in all respects, curing, cleaning the surface neatly at the time of handing over the area, all materials and labour complete. as per specifications and as directed by the Engineer-in-Charge. Note: The sample tile shall be got approved by the Architect/Engineer before procurement.

Providing and fixing VITRIFIED Floor tiles in different sizes with water absorption less than .08 % and confirming To Is 15622 of Marbonite or approved make in all colors and shades in Glossy or mat or Satin finish ( as required by Engineer -in- Charge) laid over a bed of minimum 20 mm thick bed of cement mortar ( 1:4) including machine/hand cutting to required size & shape , grouting the joints with white cement mixed with coloring pigment to match colour of tile patterns , curing, cleaning the surface neatly at the time of handing over the area complete all as per drawings and specifications. Note:- The sample tile shall be got approved by the Architect/ Engineer before Procurement.

Providing and fixing VITRIFIED wall tiles (in skirting, risers of steps and dados) in different sizes with water absorption less than .08 % and confirming To Is 15622 of Marbonite or approved make in all colors and shades in Glossy or mat or Satin finish ( as required by Engineer -in- Charge) laid over a bed of minimum 20 mm thick bed of cement mortar ( 1:4)( in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3) including machine/hand cutting to required size & shape , grouting the joints with white cement mixed with coloring pigment to match colour of tile patterns , curing, cleaning the surface neatly at the time of handing over the area complete all as per drawings and specifications. Note:- The sample tile shall be got approved by the Architect/ Engineer before Procurement.

Providing and laying with very good quality Designer tiles of make "Eurocon" / "Ultra" or other approved equivalent make of pre-polished cement concrete tiles for Flooring/cladding conforming to IS Specifications of approved size, shape and colour in CM 1:1 over brickwork/concrete surfaces over a base coat of 20mm thick CM 1:3, including filling the joints with the matching colour paste (white cement plus colour pigments), simultaneous sunk pointing at all levels, scaffolding, curing, finishing (washing the floor with soap solution) etc., all complete as per specifications and as directed by the Engineer.

Providing 20 mm nominal bore sizes of LEADER make gun metal full way gate valves female ends screwed bonnet integral seat non rising spindles class I ISI marked to IS: 778 tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing 25mm nominal bore sizes of LEADER make gun metal full way gate valves female ends screwed bonnet integral seat non rising spindles class I ISI marked to IS: 778 tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing 40 mm nominal bore sizes of LEADER make gun metal full way gate valves female ends screwed bonnet integral seat non rising spindles class I ISI marked to IS: 778 tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing 50 mm nominal bore sizes of LEADER make gun metal full way gate valves female ends screwed bonnet integral seat non rising spindles class I ISI marked to IS: 778 tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing 80 mm nominal bore sizes of LEADER make gun metal full way gate valves female ends screwed bonnet integral seat non rising spindles class I ISI marked to IS: 778 tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing 50 mm nominal bore sizes of LEADER make gun metal Horizontal type Non Return Valve female ends screwed class I ISI marked to IS: tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing 80 mm nominal bore sizes of LEADER make gun metal Horizontal Type Non Return Valve female ends screwed class I ISI marked to IS: 778 tested to 20 kg/sqcm hydraulic pressure etc. complete all as per specification a and direction of engineer in charge

Providing and fixing on the wall 20mm nominal size ( CPVC) pipes thickness 2.0 to 2.50 mm Chlorinated Poly Vinyl Chloride ( CPVC) SDR 11 pipes Supreme/ Flow Guard/Jain/Kissan or other approved equivalent make having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings (cost of all types of specials such as tees, reducers, coupler, reducing bushes, threaded adaptor fittings ("T", Elbow,MTA/FTA), elbow, tail pieces, caps etc.,) including jointing of pipes & fittings with one step CPVC solvent cement, fixing the pipe with clamps at 1.00 m spacing and testing the line as directed by the Engineer in charge.

Providing and Fixing on the wall 40 mm dia Nominal size Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 Supreme/ Flow Guard/Jain/Kissan or other approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing all CPVC plain and brass threaded fittings, fixing the clamps at 1m spacing, pvc plugs, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Internal work- Exposed on wall) 40mm dia Nominal size

Providing and Fixing in gound 40 mm dia Nominal size Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 Supreme/ Flow Guard/Jain/Kissan or other approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing all CPVC plain and brass threaded fittings, fixing the clamps at 1m spacing, jointing of pipes and fittings with 1 step CPVC solvent cement, testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Internal work- Under ground) 40mm dia Nominal size

Providing and Fixing in trench 50mm dia Nominal size Chlorinated Polyvinyl Chloride (CPVC) pipes (Class-I) of SDR-11 of Supreme/ Flow Guard/Jain/Kissan or other approved make conforming to IS 15778 having thermal stability for hot and cold water supply including providing all CPVC plain and brass threaded fittings, jointing of pipes and fittings with 1 step CPVC solvent cement, and testing of joints, etc., all complete as per specification and as directed by Engineer In-Charge. (Note:- For External work- In Ground exluding excavtion of trench) .

Providing of uPVC pipe 76mm OD FINOLEX/PRINCE or other approved equivalent make of UPVC stabilized - SWR PVC pipes - Type B (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) conforming to IS - 13592 - Latest edition and PVC pasting type specials such as door bends, door tees and cowls etc. heavy quality for soil waste or vent or antisyphonage PVC pipe with necessary PVC clips and joints complete all as per drawings, specifications and as directed by the Engineer-in-Charge.

Providing 90mm OD uPVC pipes FINOLEX/PRINCE or other approved equivalent make of UPVC stabilized - SWR PVC pipes - Type B (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) conforming to IS - 13592 - Latest edition complete all as per drawings, specifications and as directed by the Engineer-in-Charge..

Providing 110mm OD uPVC pipes FINOLEX/PRINCE or other approved equivalent make of UPVC stabilized - SWR PVC pipes - Type B (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) conforming to IS - 13592 - Latest edition complete all as per drawings, specifications and as directed by the Engineer-in-Charge..

Providing 75 mm to 100 mm dia UPVC pasting type specials suitable to UPVC Soil Pipes Type- B(( As per IS -13592) such as socket, door bends, door tees, door 'Y' and cowls etc. heavy quality for soil waste or vent or antisyphonage UPVC pipe .

Providing, replacing and fixing UPVC rain water downtake pipes with [existing G.I. Bracket ( 200 mm long made of 50X 6 mm flat 1 no.), anchor bolt (10 mm dia 75 mm long 2 no.) , G.I."U" clamp for 100 mm], PVC pipe made of 3 mm thick, PVC rawl Plug each joint at 1.7 meter center to center pipe fixed to walls wherever required FINOLEX/PRINCE or other approved equivalent make of UPVC stabilized - SWR PVC pipes - Type A (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) conforming to IS - 13592 - Latest edition and PVC solvent jointing complete all as per drawings, specifications and as directed by the Engineer-in-Charge..110mm OD PVC pipes and specials.

Providing and fixing PVC Nahni trap of size( 110x75mm) of FINOLEX/PRINCE or other approved equivalent make conforming to the relevant IS code, heavy quality of self cleaning design with 75mm internal dia and outlet 125mm dia. PVC grating with perforated holes on top, including embedding in cement concrete 1:2:4, forming circular holes by providing and fixing 110mm OD PVC pipes of required height up to floor level, leveling and rendering smooth, making good the floor and wall etc. complete as per specifications. (Rate shall include cost of PVC pipe and it shall not be paid extra).

Providing and fixing PVC Multi connection Floor trap of Size(100mmx75mmx75 mm) of Flow gaurd/ Supreme/FINOLEX/PRINCE or other approved equivalent make conforming to the relevant IS code, heavy quality of self cleaning design with 110mm internal dia and outlet 125mm dia. PVC grating with perforated holes on top, including embedding in cement concrete 1:2:4, forming circular holes by providing and fixing 110mm OD PVC pipes of required height up to floor level, leveling and rendering smooth, making good the floor and wall etc. complete as per specifications. (Rate shall include cost of PVC pipe and Embedding PCC ,it shall not be paid extra).

Taking out C.I. Cover with frame from R.C.C. top slab of inspection chambers of various sizes including demolishing of RCC work manually /by mechanical means and stacking of use full material near the site and disposal of unserviceable materials within 50 metres leadasper direction of Enginer-in-Charge.

Providing and fixing fiber reinforced polymer frame and cover (300x300 mm) PRINCE or other approved equivalent make conforming to the relevant IS code,2:4, forming circular holes by providing and fixing 110mm OD PVC pipes of required height up to floor level, leveling and rendering smooth, making good the floor and wall etc. complete as per specifications. (Rate shall include cost of PVC pipe and it shall not be paid extra).

Supply and fixing of Composite (FRP/GRP) manhole cover & frame of size 450x450mm and classification of make HP-Strong Drain or Everlast or other approved equivalent make including fixing/embedding the frame in concrete, finishing to match the surface level, placing the cover, etc., all complete as directed by Engineer-in-charge. Note : Cost concrete to embed the frame shall be paid for seperately under relevant item

Supply and fixing of Composite (FRP/GRP) manhole cover & frame of size 600x600mm and classification of make HP-Strong Drain or Everlast or other approved equivalent make including fixing/embedding the frame in concrete, finishing to match the surface level, placing the cover, etc., all complete as directed by Engineer-in-charge. Note : Cost concrete to embed the frame shall be paid for seperately under relevant item

Making connection of drain or sewer line with existing manhole including breaking in to and make good the walls, floors with cement concrete 1:2:4 mix (1cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size) cement plastered on both side with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary For pipes 100 mm to 230 mm diametre

Providing and fixing heavy quality 15mm C.P. Brass stop COCK with wall flange of ”JAQUAR' [Continental Series] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification.

Providing and fixing heavy quality 15mm CP brass Angle Stop Cock with wall flange of 'JAQUAR’ [Continental Series] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification.

Providing and fixing heavy quality C.P. Brass Wall Mixer(Two in One) with provision for Overhead Shower with 115mm long bend pipe and wall flange of PARRYWARE( G572FA1)/”JAQUAR’ [Continental Series] or approved equivalent make including fixing with flange etc., all complete as per specification.suitable

Providing and fixing heavy quality 15mm C.P. Brass SINK COCK with swinging spout and wall flange of PARRYWARE((G3321A1)/ JAQUAR’ [Continental Series - Wall Mounted] or approved equivalent make including fixing with suitable SS valve/cup, flange etc., all complete as per specification.

Supplying of tested heavy quality C. I. specials/ fittings like sockets, spigot and flanged specials such as bends, collars, tappers, tees, duck foot bend, flanged socket and flanged spigot tail pieces, blank flanges etc. and confirming to IS and socket specials/ fitting shall be suitable for rubber gasket/lead joint etc. completed. (Joints will be paid for separately under relevant items).

Supplying of tested heavy quality D. I. specials/ fittings K12 class like mechanical joint collar ,sockets, spigot and flanged specials such as bends, collars, tappers, tees, duck foot bend, flanged socket and flanged spigot tail pieces, blank flanges etc. and confirming to IS and socket specials/ fitting shall be suitable for rubber gasket/lead joint etc. completed. (Joints will be paid for separately under relevant items).

Providing 6 mm thick ( 600x450 mmX6mm) Mirrors "Modiguard" or approved make with beveled edges complete with 6 mm thick asbestos sheet background

Providing best quality white Universal type Water closet with seat cover white of M/s. Parryware Sanitary ware, Hindware or Johnson make white glazed vitreous chinaware, conforming to IS: 2556-1973

Providing best quality Economy 10lts. capacity DUAL FLUSH (E8057) LOW LEVEL FLUSHING CISTERN of plastic cistern of gleaming white /color shade conforming to IS 7231 SLIMLINE make with all internal non ferrous fittings and matching flush bend mounted on a pair of suitable brackets etc., complete as per drawing, as per specifications and as directed by the Engineer.

Providing White/ Color SOLID PLUS(E8307 Soft Close White) soft close plastic seat Cover For European type water closet "PARRYWARE" make .

roviding White/ Color SOLID PLUS(E8307 Soft Close White) soft close plastic seat Cover For European type water closet "PARRYWARE" make

Supplying and fixing of CP toilet paper roll holder of parryware(T60051)/"Jaquar" [Continental series - ACN1155N] or approved equivalent make including fixing it to the wall, finishing the joints with white cement or approved grouting materials etc., all complete as per specification and as directed by the Engineer-in-charge.

Supplying and fixing of CP toilet paper roll holder of parryware(T60051)/"Jaquar" [Continental series - ACN1155N] or approved equivalent make including fixing it to the wall, finishing the joints with white cement or approved grouting materials etc., all complete as per specification a

Providing Connection Hose 1.5 feet T991299 Parryware make

Providing heavy quality 15mm C.P. Brass BIB COCK Metro ( Omega) make and suitable SS valve/cup complete all as per specifications and as directed by Engineer -In-Charge.

Providing heavy quality 15mm C.P. Brass BIB COCK long Body Omega (Metro ) make and suitable SS valve/cup complete all as per specifications and as directed by Engineer -In-Charge.

Providing heavy quality 20mm C.P.Brass screw down CONCEALED TYPE STOP COCK 'PARRYWARE' Agate G0651A1 &G5053A1 (concealed body CSC & Upper trim CSC) make and suitable SS valve/cup. complete all as per specifications and as directed by Engineer -In-Charge.

Providing heavy quality 15mm C.P.brass ANGLE STOP COCK without pipe PARRYWARE STAR MODEL (T9926A1)make and suitable SS valve/cup. complete all as per specifications and as directed by Engineer -In-Charge.

Providing Two Way Bib Cock with Two Knobs (T5834A1) Parryware make complete all as per specifications, drawings and as directed by Engineer-in charge.

Removing of white wash/color wash with mechanically, using vacuum type sanding machine, with hand using scraper, wire brush, sand paper etc. cleaning the dust from the door, window and other area ,disposal of debris within one Km at specified location complete all as per specification and directed by the Engineer-in-charge.

Providing and supply, Applying one internal surface one coat of water thinnable cement primer (Asian/ Snowcem or other approved brand and manufacture) on wall surface including labour, material ,preparation of the surfaces scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete all as per specifications, drawings and as directed by Engineer-in charge.

Providing and applying painting Two coats at all levels with Premium Plastic emulsion paint, (Apcolite of Asian or Equivalent approved brand, colour and manufacturer) having VOC (Volatile Organic Compound) content less than 50 grams/liter to give an even shade including one under coat of cement primer having VOC (Volatile Organic Compound) content less than 50 grams/liter , applying putty, preparation of the surfaces cover scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying painting One coat at all levels with Premium Plastic emulsion paint of (Apcolite Asian or Equivalent approved brand, colour and manufacturer) having VOC (Volatile Organic Compound) content less than 50 grams/liter to give an even shade including preparation of the surfaces, applying putty, scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and supply, Applying on external surface one coat of water thinnable cement primer (Asian/ Snowcem or other approved brand and manufacture) having VOC (Volatile Organic Compound) content less than 50grams/liter , on wall surface including labour, material ,preparation of the surfaces scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and supply, Applying Two coat of water thinnable Water proof cement Paint ( Snowcem Plus or other approved brand and manufacture) on wall surface including labour, material ,preparation of the surfaces scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying painting Two coats at all levels with premium Acrylic emulsion paint (ACE of Asian or Equivalent approved brand, colour and manufacturer) to give an even shade including one under coat of suitable primer, applying putty, preparation of the surfaces scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying painting Two coats on wood work and other required internal surfaces at all levels with Synthetic Enamel paint (Asian or approved brand, colour and manufacturer) to give an even shade including one under coat of suitable primer, preparation of the surfaces, scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying painting One coat on wood work and other required internal surfaces at all levels with Synthetic Enamel paint (Asian or approved brand, colour and manufacturer) to give an even shade including preparation of the surfaces, scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying painting One coat on steel door/window work and other required internal surfaces at all levels with Polyurethane paint (Asian or approved brand, colour and manufacturer) to give an even shade including preparation of the surfaces, scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

Providing and applying painting one coat on surface at all levels with white/ color Acrylic Emulsion Paint ( Asian Apex or equivalent approved, brand and manufacturer) to give an even shade including preparation of the surfaces, scaffolding, curing complete all as per , specifications and as directed by the Engineer-in-Charge. ( For ROAD KERB WALL AND SPEED BREAKER )

Removing and Re- laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.( Note:-Including labour charge of removal of tile and Excluding the cost of Roof tiles)

Providing and laying pressed flat clay tiles 230 x 230 mm size and 20mm thick tiles on roofs slave jointed with cement mortar 1:3 (1 cement : 3 coarse sand) mixed with 2% integral waterproofing compound lied over a bed of 20 mm thick cement mortar 1:3 and finished neat complete all as per specifications and as directed by the Engineer-in-Charge.

Cleaning the over head water tanks located at a height up to 20 Meters. above ground level by closing the in coming valve of water line, draining out the existing water in the tank, thoroughly cleaning the inside of the tank by using brush and Active Bleaching Powder completely, removing the dirty materials, closing the scour valve and releasing the water into the tank after thoroughly cleaning, re-fixing the manhole cover in position etc. including cost of labor. Bleaching Powder and all tools & tackles etc. complete all as per specification and as directed by Engineer -in- charge. ( Note:- Tank cleaning shall be as per time mentioned in check list. Check list shall be cleared by departmental supervisor.) Residential buildings(IV D,III C & II B type) (0.6kg of Active Bleaching Powder shall be used for cleaning the tank)

Cleaning the over head water tanks located at a height up to 20 Meters. above ground level by closing the in coming valve of water line, draining out the existing water in the tank, thoroughly cleaning the inside of the tank by using brush and Active Bleaching Powder completely, removing the dirty materials, closing the scour valve and releasing the water into the tank after thoroughly cleaning, re-fixing the manhole cover in position etc. including cost of labor. Bleaching Powder and all tools & tackles etc. complete all as per specification and as directed by Engineer -in- charge. ( Note:- Tank cleaning shall be as per time mentioned in check list. Check list shall be cleared by departmental supervisor.) Public buildings(Big size)(1.00kg of Active Bleaching Powder shall be used for cleaning the tank)

Cleaning the over head water tanks located at a height up to 20 Meters. above ground level by closing the in coming valve of water line, draining out the existing water in the tank, thoroughly cleaning the inside of the tank by using brush and Active Bleaching Powder completely, removing the dirty materials, closing the scour valve and releasing the water into the tank after thoroughly cleaning, re-fixing the manhole cover in position etc. including cost of labor. Bleaching Powder and all tools & tackles etc. complete all as per specification and as directed by Engineer -in- charge. ( Note:- Tank cleaning shall be as per time mentioned in check list. Check list shall be cleared by departmental supervisor.) Residential buildings( V E type)(0.25kg of Active Bleaching Powder shall be used for cleaning the tank)

Cleaning the Under Ground Storage Sumps of Six lakh liter capacity a depth of up to 4.0 meters. below ground level by dewatering, cleaning the wall, floor surface by removing the deposited silt, sand etc. Cleaning and washing walls /floor thoroughly with bleaching powder and bailing out the dirty water etc. at the places shown etc. complete including cost of labor, bleaching powder, tools & tackles all as per specification and as directed by Engineer -in- charge(4.00kg of Bleaching powder shall be used for cleaning the tank) ( Note:- Tank cleaning shall be as per time mentioned in check list. Check list shall be cleared by departmental supervisor.)

Cleaning the under ground sewer line/drain line including Inspection chamber, man -hole, cleaning all the sludge and washing with water etc. complete all as per specifications and as directed by Engineer-in-charge.( Note:- Sewer cleaning shall be as per time mentioned in check list. Check list shall be cleared by departmental supervisor.)

Providing, making and fixing second class Teak wood work in frames of doors, windows, clerestory openings and other frames, wrought framed, fixed in position of required size and shape including sawing, jointing, marking rebates for shutters, making grooves as shown in the drawings, architectural beading with teak wood 50 X 6 mm all-round, finishing the surface to the required finish all as per specification and drawings including necessary MS hold fasts 300 mm long, 5 mm thick or with rawl plucks and screws including protective painting to the surface that will come in contact with walls, joining materials, labours etc., complete all as per specifications and as directed by Engineer-in-Charge

Providing and fixing 30 mm thick second class teak wood glazed window shutters using size of 75x30 mm including the ISI marked heavy quality 75 mm long Stainless steel Butt hinges 2 Numbers for and necceessary screws for the each shutter with 5 mm Glazed panelling including fixing in window frame complete all as per specification and directed. design of the glazed window to be got approved by the Engineer-in-chrage.

Providing and fixing glazing with 5 mm thick clear float glass pane in aluminum doors, windows, ventilator shutters and partitions etc. with Neoprene gasket including cost of Neoprene gasket complete as per the drawings and directions of the Engineer-in-charge.

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including supply and fixing of 250 mm dia RCC Collar and repairing of wall, making good the same etc. complete as per direction of Engineer-in-charge.

Modification of existing Glazed windows to accommodate 1.50 Ton Air conditioner by cutting the existing window and introducing 1300 to 1500mm long second class Teak wood of size 100 x 50mm horizontally and using retrieved wood for vertical support, Providing and replacing new shutter with 65x35mm frame work, 4mm thick sheet plain glass with necessary beading and new M.S. grill of existing pattern for side open portion including altering/fixing the existing shutter and grill of existing pattern to required size and shape using the dismantled materials wherever possible for top portion, Providing and replacing75mm long SS butt hinges, 100mm aluminum 'D' Handles, 100mm aluminum Tower bolts, 230mm long Aluminium peg stay with necessary screws, painting with two coats of synthetic enamel paint to match the existing surface over a coat of wood primer etc., complete at all lifts all as per specifications and as directed by Engineer-in-charge.

Attending/opening night on non -availability of key and re fixing after service of Night latch door lock complaints on emergency basis as and when required by engaging qualified carpenters with helper for Residential quarters of different types to including caring ladder etc. all lifts etc., complete as per specification and as directed by the Engineer.

Providing of single leaf of 35 mm thick non decorative type factory made wood Polymer Composite (WPC) solid door shutters both side pre-laminated of approved make ( ecoste or other equivalent make ) having density of 600 kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa all complete as per specification and as directed by Engineer in Charge.

Providing of single leaf of 30 mm thick non decorative type factory made wood Polymer Composite (WPC) solid door shutters both side pre-laminated of approved make ( ecoste or other equivalent make ) having density of 600 kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa all complete as per specification and as directed by Engineer in Charge.

Providing of single leaf of 28 mm thick non decorative type factory made Wood Polymer Composite (WPC) solid door shutters both side pre-laminated of approved make ( Ecoste ,HardyPlast or other equivalent make ) having density of 550 kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa all complete as per specification and as directed by Engineer in Charge.

Providing of single Rebate solid door frame of Size 100X50 mm thick factory made wood Polymer Composite (WPC) (IVORY color) of approved make (Ecoste/HARDY PLAST or other equivalent make ) having density of 900 kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa all complete as per specification and as directed by Engineer in Charge.

Providing of single Rebate solid door frame of Size 75X50 mm thick factory made wood Polymer Composite (WPC) (IVORY color) of approved make (Ecoste/HARDY PLAST or other equivalent make ) having density of 900 kg/Cum, water absorption less than 1% and tensile strength greater than 12 MPa all complete as per specification and as directed by Engineer in Charge.

Providing Open Profile ( PUF INSULATED / filled) Door frames fabricated from roll formed sections made of Galvanized Steel (Base Steel as per IS 513  quality, Galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 1.20 mm ( section 105mmX60mm ), coated with one coat of ETCh primer. The frame sections should be cut to length and mitre joined with Corner Bracket made of CRCA Powder Coated, Hold fast 24X6X100 mm long provided 3 places in each side of frame. Tie Rod in 10mm square bar provided at Bottom, with necessary provision( holes) for fixing SS hinges, fixing of night latch , fixing of Aldrop 16 mm dia, fixing of Tower bolts ,fixing of door chain etc. specification complete as per direction of Engineer-In-Charge

Attending day to day complaints on minor repair in Aluminium Door window, wooden (Door, windows), Steel Door /windows/ wooden cupboards/ steel cupborad various types by servicing the fittings and replacing the worn out fittings if any re-fixing same and also other carpentry related complaints if any etc. complete all as per direction of Engineer - in charge. (Note:-The work shall necessitate one Fitter/Carpenter/Welder with one helper man mazdoor, carpenter and one helper /man mazdoor for executing the works from 9.00 AM to 17.30 PM.)

Replacement White vitreous china water closet squatting pan (Indian water closet ) along with "S" or "P" trap including removing/ dismantling of old WC seat and "S" or "P" trap, removing of sand &shifting to ground, with all operations including all necessary materials ( cement, sand , grit etc) , labour for fixing of IWC , refilling of sand/compaction and disposal of dismantled material i/c malba up to 1KM, all complete as per the direction of Engineer-in charge.( Note :-Excluding cost of IWC )

Replacement of European water closet with "S" or "P" trap including fixing require 100 mm dia pipe UPVC Pipe, 100 mm dia UPVC " T", 100 mm dia Nahani Trap, 100 mm PVC Grating with all operations including all necessary materials PVC rawl plugs, SS screws, ( cement, sand , grit etc) , labour for fixing of EWC , Re-connection of flush tank and disposal of dismantled material i/c malba up to 1KM, all complete as per the direction of Engineer-in charge.( Note :-Excluding cost of EWC )

Providing and laying 300 mm dia non pressure NP2 class RCC Hume pipes conforming to IS;458, with collars jointed with stiff mixture of cement mortar in proportion of 1:2 using crushed stone sand, laying to the levels, slopes including testing of joints etc. complete all as per the drawings and specifications as directed by the Engineer-in-charge.

Providing and fixing double Tubular Using H frame/AOS System (cup lock type) on the exterior side up to seven storey height made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal and vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once irrespective of duration of scaffolding (3) The scaffolding shall be paid only for repair work like mainly roof tile work ,dismantling, brickwork, plaster, RCC , formwork, reinforcement etc. wherever required.

Re-fixing of G.I. pipes 20 mm dia 50 mm dia complete including supply of G.I. Clamps, S.S. screws, Plug , and fixing removing old clamps/packing wood, filling the holes with cement mortar(1:4)/ concrete( 1:2:4) and making good the wall and painting with two coat of cement paint ( Smocem Make)

Providing and Painting 20 mm dia G.I. pipes and fittings with synthetic enamel paint with two coats over a ready mixed priming coat (red oxide zinc chromate), both of approved quality for approved brand and manufacture and required colour on old work including labour,scafolding, sand paper, ware brush, paint brush etc complete as per direction of engineer-in-charge and specification.

Providing and Painting 40 mm - 50 mm dia G.I. pipes and fittings with synthetic enamel paint with two coats over a ready mixed priming coat (red oxide zinc chromate), both of approved quality for approved brand and manufacture and required colour on old work including labour,scafolding, sand paper, ware brush, paint brush etc complete as per direction of engineer-in-charge and specification.

Providing of 43 grade ( 50 kg ) OPC cement

Providing of WHITE cement

Providing of PTA STAR Screw 4x25 mm (1000 No)

Providing of PTA STAR Screw 4x35 mm (1000 No)

Providing of PTA STAR Screw 4x50 mm (400 No)

Providing of PTA STAR Screw 6x75 mm (250 No)

Attending day to day complaints on minor masonry repair in PCC, RCC, brick work, plaster, flooring, plumbing making exhaust fan opening, replacing/ fixing ( door frame, window frames) and other masonry related complaints at all levels etc. complete all as per direction of Engineer - in charge. (Note:-The work shall necessitate one mason with one helper man mazdoor, for executing the works from 9.00 AM to 17.30 PM.)

Attending None scheduled Micslaneous items like cleaning of stores / stacking materials/ shifting of material, cleaning of valve pits , cleaning of terraces /sunshades, Cleaning around sewer line chamber, cleaning of houses ,removing of debris etc on complaint basis and other masonry related complaints at all levels etc. complete all as per direction of Engineer - in charge. (Note:-The work shall necessitate one helper /man mazdoor, for executing the works from 9.00 AM to 17.30 PM.)

Supply of Godrej make Ultra XL+ Vertibolt with Four Keys as per detail Specification