GE 861 EWS-85/2024-25

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

ditto as per Item No.2 above for each additional 1.5 m or part thereof in depth beyond the first 1.5 m complete all as specified and directed by Engineer-in-Charge.

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type D2, 1:4:8 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design Mix, M-25) using 20mm graded crushed stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design Mix, M-25) using 20mm graded crushed stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design Mix, M-25) using 20mm graded crushed stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design Mix, M-25) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete (Design Mix, M-25) using 20mm graded crushed stone aggregate in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed by Engineer-in-Charge.

S&F Mild Steel TMT bars 10mm and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip complete all as specified and directed by Engineer-in-Charge.

S&F Mild Steel TMT bars 5mm dia and over upto and including 10mm dia cut to length, bent to shape required, including cranking, bending spirally in stirrups, spacers and binders including mild steel wire (annealed) not less than 0.90mm dia or securing with clip complete all as specified and directed by Engineer-in-Charge.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for use and waste of formwork for rough finished surfaces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed by Engineer-in-Charge.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams for rough finished surfaces etc. complete all as specified and directed by Engineer-in-Charge.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge.

M&L for Damp proof course with 40mm thick PCC 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate to horizontal or vertical surfaces including necessary formwork complete all as specified and directed by Engineer-in-Charge.

Dismantling of CGI/PGI Sheet fixed with screws as in roof covering complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engineer-in-Charge.

S&F 1.25mm thick steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed by Engineer-in-Charge.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by Engineer-in-Charge.

S&F Ball bearing for rolling shutters complete all as specified and directed by Engineer-in-Charge.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed by Engineer-in-Charge.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engineer-in-Charge.

All as per Item No 30 but without glazing bars complete all as specified and directed by Engineer-in-Charge.

M&L for framed work such as grills etc with ends of bars shouldered and or riveted or forged into spike, framed guard bars and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

M&L for two coats synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surfaces including preparation of surfaces over 10 cm width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for 3mm thick plain sheet glass ordinary quality & glazing with oil putty n.exc 0.50 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

M&L for 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples including taking out old wire cloth complete all as specified and directed by Engineer-in-Charge.

M&L Chowkhat 2nd class hard wood and frames wrought , framed rebated on the solid rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick 2nd class hardwood, factory made plain framed, panelled shutters (two panel), with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick 2nd class hardwood glazed & skeleton shutters, open repeated & prepared to received glass gauze etc. (without sash bars) edges of framing plain for securing glass etc, fitted to chowkhats complete all as specified and directed by Engineer-in-Charge.

Taking down wooden frame not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down wooden frame exc 1.5 sq. m but n exc 4 sq. m each ® (Without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5 mm wood grain printed PVC sheet with mild steel square tube complete as per manufacturer specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement fixing in the frame at site as per specification drawing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made uPVC white colour Two track two panels sliding window upto 1.50 m height made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware’s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in- Charge. (Glass or wire mesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F 5.50mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F 5.50mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer-in-Charge.

S&F Butt hinges 100MM, medium weight, stainless steel complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm aluminium handle cast type, anodised, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash down water closet (Squat pattern) white complete as fixed in repair excluding flushing cistern and flush pipe "Orissa" pattern size 580x440 with integral footrest inject connection to trap anti-syphonage etc complete including joint between flushing pipe and socket of WC complete all as specified and directed by Engineer-in-Charge.

S & F Vitreous Ware wash down water closet (Pedestal), white (EWC) and fixed in repairs including seat cover with brass screws and excluding flush pipe and flushing cistern complete all as specified and directed by Engineer-in-Charge.

S&F 10Ltr PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge.

S & F in repairs PVC Low level flushing cistern 10 Ltr capacity including all fitting such as flush pipe brackets complete all as specified and directed by Engineer-in-Charge.

S&F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F Bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F stop valve/angle valve of 15mm bore, chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm Bib Taps with wall flange of chromium plated fancy type long shank screwed for Iron Pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stop valves/angle valves for 15 mm bore of pipe cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash down water closet (Squat pattern) white complete as fixed in repair excluding flushing cistern and flush pipe "Orissa" pattern size 580x440 with integral foot rest inject connection to trap anti syphonage etc complete including joint between flushing pipe and socket of WC complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC connection of 15 mm bore and 450 mm long with brass check nut and union etc complete all as specified and directed by Engineer-in-Charge.

S&F PVC connection 15 mm size PTMT nuts of length 600 mm complete all as specified and directed by Engineer-in-Charge.

S&F soap dish vitreous china white size 160x160x90mm approx complete all as specified and directed by Engineer-in-Charge.

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

S&F Health faucet (ABS Body) chromium plated suitable for 15 mm dia pipe with 125 metre long flexible tube and ABS wall hook Including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F Vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

S&F Brass CP mixer for mixing hot & cold water screwed down for 15mm iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F Brass in repairs CP mixer for mixing hot & cold water screwed down for 15mm iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing 20mm bore and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore gun metal glove or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F 1000 Ltr Capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/wall or in floors complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/wall or in floors

S&F 110mm bore PVC (SWR) bends any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore PVC (SWR) bends any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) junction double, (double T), equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F PVC 75(SWR) junction single, (Single T), equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

M&L 75mm outlet dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S &F Mild steel sliding door bolts 250mm long, plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and two on staple plate and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 300MM Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 100mm Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed by Engineer-in-Charge.

S&F MS ordinary rat tail rod pattern spring 300mm including roller and roller plate on wooden/steel chowkhat including welding, riveting etc complete all as specified and directed by Engineer-in-Charge.

S&F 200mm Mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and directed by Engineer-in-Charge.

S&F 150mm Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 125mm Cast iron or malleable cast iron handles, cast type, stove enamelled black complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long Cast iron or malleable cast iron handles, cast type, stove enamelled black complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by Engineer-in-Charge.

S&F in repair 2nd class small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by Engineer-in-Charge

S&F Mild steel flat iron 25x6mm as in hold fasts including all necessary cutting etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in bed block for fixing of hold fasts etc. complete all as specified and directed by Engineer-in-Charge.

M&L for painting on new wooden based surfaces of any description not other wise described over 10cm width or girth applying two coat synthetic enamel paint over one coat of pink primer including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for Hard core of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 150mm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (Unreinforced) in ground floor and paving n exc 15 cm thick blow or above ground level complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) as in sub base floor complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick Cement concrete type B-2,1:2:4 (using 40mm graded crushed stone aggregate) as in floor finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick Cement concrete type C- 2,1:3:6 (using 40mm graded crushed stone aggregate) as in subbase of floor complete all as specified and directed by Engineer-in-Charge.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (using 12.5mm graded crushed stone aggregate) as in floor for levelling course complete all as specified and directed by Engineer-in-Charge.

M&L Non-skid joints free Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry over screed bed or bedding layer of 15 mm thick with cement mortar 1:4 and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry over 10 mm thick rendering with CM 1:4 and pointed in white or colour cement to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

M&L for Plain cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in coping, pedestal complete all as specified and directed by Engineer-in-Charge.

M&L for Precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate for cover slab for Man holes / Septic tank set in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M&L Machine cut kota stone slab flooring 20-25mm thick over 20mm cement screed base of CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius for Wall, manholes/septic tank/soak well etc/ in sewer works with old size bricks in Cement Mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls with old site bricks built in CM 1:4 complete, in walls complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls etc including raking out joints, hacking for key scrubbing down with water and removal of rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15mm thick in CM 1:4 using liquid waterproofing compound as per manufacturer instruction on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick rendering in cement mortar (1:4) inside and outside brick wall of manhole /septic tank /concrete surfaces even and smooth without using extra complete all as specified and directed by Engineer-in-Charge.

M&L for Setting coat of 3mm thick of CM (1:2), trowelled to even and smooth finish over rendering 15mm thick in CM 1:4 on fair faces of brick work finished surface even & smooth with using water proofing compound complete all as specified and directed by Engineer-in-Charge.

Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-Charge.

S&F 6mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood (Kail) in scantling clean sawn and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section wrought fixed with nails exc 3 Sqcm and n exc 6 Sqcm bull, splayed, chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

S&F 2nd Class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 6 but not exc 13 sqcm complete all as specified and directed by Engineer-in-Charge.

S&F 2nd Class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 13 but not exc 25 sqcm complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section wrought fixed with nails n exc 3 Sqcm bull, splayed, chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm thick 2nd class softwood boarding planed one side with butt joint with nails in any situation complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L, for preparation of new surfaces of wall priming with alkali resistant primer and applying two coats of cement based paint complete all as specified and directed by Engineer-in-Charge.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer-in-Charge.

M&L complete removal of existing surface of old plastered surface of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces of wall and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper emulsion over 1 mm thick wall care putty over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old surfaces ceiling and applying one coat of oil bound distemper emulsion complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old surfaces of ceiling and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick Cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement.

M&L for Concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 using 40mm graded stone aggregate all as specified and directed.

M&L RCC pipes class NP-2 with socketed ends laid and jointed complete of 150mm bore complete all as specified and directed by Engineer-in-Charge.

M&L for Construction of 1.2 M dia and 3m depth Soakage wells including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonry in CM, RCC cover slab in M25/ SFRC cover, inter connecting pipes of RCC/DWC complete filled with brick bats of size complete as per drawing enclosed with tender Documents and all as specified and directed by Engineer-in-Charge.

Supply fixing and errection of On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 20 users complete all as specified and directed by Engineer-in-Charge.

Returning, filling in and including spreading, levelling, watering & well ramming in layers n.exceeding 25 cm in soil complete all as specified and directed by Engineer-in-Charge.

Removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in oft/loose soil complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size, & as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-149 here in above but for one 5A socket outlet on the same board controlled by one switch.

All as per srl item No-149 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

Description all as per item No 149 above but for 3 pin socket outlet 15 Amps independent board with 2.5 Sqmm.

Supply & fixing switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified and directed by Enginee-in-Charge.

M&L for Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal 230 volts complete all as specified and directed by Enginee-in-Charge.

M&L for Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal 230 volts complete all as specified and directed by Enginee-in-Charge.

Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp 10 W complete all as specified and directed by Engineer-in-Charge.

S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning. complete all as specified and directed by Engineer-in-Charge.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge. (ii) SPN 32 AMP

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to centre both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , for pit cover including testing on completion complete all as specified and directed by Engineer-in-Charge. Note:-After completion of work if desired test result is not obtained the earthing is to be redone without any extra cost to deptt.

Supply and Fixing exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge.

Supply and installed water heater vertical type, stationary storage type of 25 ltr capacity having S/S inner vessal, five star rating , ISI Marked close/vented type (star marked) , 240 volts with heating element and autocut thermostat, maximum output of hot water is 60 degree celsius, including fixing arrangement nut bolts, washer/fasteners and finishing work etc complete as per existing surface, complete all as specified and directed by Engineer-in-Charge.

Supply and laying or fixing or passing through pipe or binding with fencing/pole etc, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 Sq mm nominal cross section 2 core solid conductor complete all as specified and directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete all as specified and directed by Engineer-in-Charge.

JANDOO AND CO (BID ID -3265506)