GE S U 04 2022 23 REWIRING OF BUILDING NO NP04 AND NP05 OR LIVING OTM ACCN REPAIR REPLACEMENT OF CERTAIN BER OF CEILING FANS EXHAUST FANS ELECTRONIC METERS PROVN OF CALL BELL IN CERTAIN JCOS OR MD ACCN PROVN OF CEILING FANS AND CERTAIN BR

Amount

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick below or above ground level complete all as specified and directed.

Demolition of cement concrete (reinforced) as in roof, floors (other than ground floor), beams, staircase, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square meter each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square meter each, including cutting holes for taking out fasts or dismantling brick work (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish any extra cost to Govt) complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking up or down steel tubing 15 mm bore including cleaning for refixing or removal to store complete all as specified and directed.

All as per ser item No 7 above but 20 mm Bore complete all as specified and directed.

Demolition of and breaking up of AC rain water pipes any dia fixed in any position complete all as specified and directed.

Dismantling water tank of capacity exceeding 250 ltrs but not exceeding 500 ltrs complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

PCC 75 mm thick 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and directed.

10 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

Non skid coloured ceramic tiles (square/rectangular) 8 to 9 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles complete all as specified and directed.

Coloured glazed ceramic tiles 300 mm x 600 mm x 7 mm/300 mm x 450 mm x 7 mm or 8 mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments in vertical surfaces complete all as specified and directed. Note : Contractor shall have no claim on colour or shade what so ever on this account complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200 mm thick surface horizontal or sloping, fair finished surface of concrete complete all as specified and directed.

Precast cement concrete Block (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in bond stones set in cement mortor 1:6 complete all as specified and directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Rendering 15 mm thick in two layer (10 + 5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed. (Water proofing compound to be measured and paid for separately).

10 mm thck rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 5 mm thick on fair faces of concrete such as chajjas/ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and directed. Note : Rate quoted by contractor deemed to be included for plastering chajjas to up to height of 10 mtrs.

Rendering 10 mm thick in CM 1:3 on roof sufaces, finished even and smooth without using extra cement complete all as specified and directed. Note :- Supply only water proofing compound shall be measured and paid seperately under the respective item.

Applying bituminous primer on roof surfaces @ 0.40 liters/Sqm and applying one coat of semi hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and thereafter supply and laying 3mm thick polymeric water proofing membrane, five layered, of weight not less than 3 Kg per Sqm with centre layer core of 90 micron high molecular density polyethylene film and bonded completely to the surface with overlap of 10 cms (overlaps to be thermo fused by flame) followed by another coat of semi hot blown bitumen 85/25 grade bitumen @ 0.70 Kg/Sqm and provide aluminium paint as per manufacturers instruction complete all as specified and directed. Note:- Water proofing treatment will be done by IWL or through a specialized agancy.

Supply only Liquid water proofing compound complete all as specified and directed.

Two coats cement base paint on newly plastered surfaces including preparation of surfaces on external walls complete all as specified and directed.

Two coats of white wash on newly plastered wall surfaces over a coat of chalk whiting as preparatory to distempering including preparation of surfaces complete all as specified and directed.

Three coats of white wash on newly plastered ceiling surfaces including preparation of surfaces complete all as specified and directed.

Pressed steel frames of size 105mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified supplied and fixed as in repair complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified and directed.

35 mm thick flush shutters, premium quality, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Factory made PVC door frames of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube suitable for opening as per site condition complete all as specified and directed and shown in SSR.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling, of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed and shown in SSR.

Factory made mild steel ventilators box type with upper top hung with glazing bars, shutters and bottom openable,locking arrangements type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 ii) Glazing, wire gauge and Glass shall be measured and paid for separately.

3 mm thick figured glass, pin head type and glazing with wooden beading, not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Aluminium alloy wire cloth, 0.45 mm nominal dia of wire & average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

Extruded aluminum alloy handles, fabricated type and powder coated, 150 mm size complete all as specified and directed.

All as per ser item No 40 here in before but 100 mm complete all as specified and directed.

Aluminium alloy, anodised, 200 mm sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruted sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

All as per ser item No 43 here in before but 100 mm long complete all as specified and directed.

15 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches complete all as specified and directed.

All as per ser item No 45 above but 20 mm bore complete all as specified and directed.

110 mm bore PVC (SWR) pipe single socketed, in any length with rubber joints fixed to walls complete all as specified and directed.

75 mm bore PVC (SWR) pipe single socketed, in any length with rubber joints laid in trenches complete all as specified and directed.

75 mm bore PVC (SWR) pipe single socketed, in any length with rubber joints fixed to walls complete all as specified and directed.

110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

110 mm bore PVC (SWR) bend with oval acees door complete all as specified and directed.

75 mm bore PVC (SWR) bend complete all as specified and directed.

110mm bore PVC (SWR) reducer complete all as specified and as directed.

Sand cast iron 'P' or S trap 100mm bore for Indian type W/C complete all as specified and directed.

75mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4 complete all as specified and as directed.

75mm bore PVC (SWR) vent cowl fixed with same dia of pipe complete all as specified and as directed.

100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and as directed.

150mm x 150mm size of gully trap Salt-glazed stoneware gully traps, square or round mouthed, type 'P' complete all as specified and as directed.

Stack clamps out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm bore of pipe complete all as specified and as directed.

Viterous china wash hand basin flat back size 580 x 450 mm excluding traps, waste, chain, plug and porcelain stopper including brackets "as in repair" complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including cast iron P trap, bore of pipe 100 mm and provision of concrete bedding "as in repair" complete all as specified and directed.

PVC flushing cistern 10 ltrs capacity with complete in let ball valve as in repair complete all as specified and directed.

Viterous China urinal half stall type white including CP spreader, waste pipe etc. "as in repair" complete all as specified and directed.

PVC waste pipe 32 mm bore with cup and washers "as in repair" complete all as specified and directed.

Chromium plated 32 mm bore size full threaded with 80 mm height including all necessry washers "as in repair" complete all as specified and directed.

15 mm bore pillar tap cast copper alloy with capstan head chromium plated screwed down under high pressure with or without lettered hot or cold with long shank and fly nuts screwed for iron pipe complete all as specified and directed.

15 mm bore angle valve, cast copper alloy chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed "as in repair" complete all as specified and directed.

Bib Tap, fancy type, cast copper alloy chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm in repair complete all as specified and directed.

20 mm bore brass float valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule "as in repair" complete all as specified and directed.

S&F in repair PVC connection 15mm bore with PTMT nuts of length 450mm complete all as specified and directed.

500 ltrs capacity rotational moulded polythene water storage tanks cylndrical with closed top hoisted and fixed in position complete all as specified and directed.

20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Aluminium anodised tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

Two coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide zinc chrome primer complete all as specified and directed.

Two coats of synthetic enamel paint on new wooden surfaces including preparation over a coat of pink primer complete all as specified and directed.

Demolition and breaking up 150mm internal dia of drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard /dense soil, complete all as specified and directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

Returning, filling including spreading leveling watering and well ramming in layers not exceeding 25mm in any type of soil complete all as specified and directed.

Removing excavated material (soils) exceeding 250 m but n.exc. 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for cement concrete 1:3:6 type C1 (20mm graded crushed stone aggregate) as in surface channels and drains including necessary formwork etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc complete all as specified and as directed.

150 mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregates) as in bed to 150 mm dia pipes including packing under, and haunching against the sides of pipes after they are laid and tested for complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel of 150mm internal dia of pipe (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

Providing precast cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate ) as in manholes cover slab etc complete all as specified and directed.

Providing cement concrete 1:2:4 type B-0 as in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia cut to length bent to shape required including cranking bending spirally for hooping ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth and getting out in soft/loose soil complete all as specified and directed.

Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed.

M&L cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in foundation, filling, sub base and mass concrete all as specified.

RCC M-25 (Design mix) (using 20mm graded crushed stone aggregate) as foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed

RCC M-25 (Design mix) (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed

Material and labour for providing Reinforced Cement Concrete M - 25 design Mix using 20 mm graded crushed stone aggregate) as in beams, cantilever, lintels over 1.5 m complete all as specified and as directed

Formwork to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed

Formwork to flat sides of columns and stanchions complete all as specified and as directed

Use and waste formwork to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantlievers, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and as directed

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

All as per srl item No. 99, above but 5mm dia and over including 10mm dia in stirrups, spaces and binders etc all as specified.

M&L for broken glass coping in cement mortar 1:3 on top of walls complete all as specified and as directed.

M&L for preparation of new plastered surfaces on walls and applying two coats of cement base paint complete all as specified and as directed

PVC (SWR) pipes 110mm bore as in weep holes complete all as specified and as directed.

Providing precast cement concrete type 1:2:4 type B-0 as in louvres and jallies 40mm thick , including all moulding but excluding frame set in cement mortor 1:4 complete all as specified and as directed

Providing cement concrete 1:2:4 type B-1(using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, formwork complete all as specified and as directed

Framed work as in doors or gates of angle or tubular section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with or including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. Fe 410 - (Gde- E- 250) complete all as specified and as directed

Walling of random rubble masonary uncoursed well bonded bedded and solidly hearted built in CM 1:6 including flush pointing at back side as work proceed complete all as specified and as directed.

PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and as directed

Extra over stone walling for hammer dressing with miximum depression on face from straight edge held against the dressed surface not exceeding 40 mm to face stones (Lime or sand stone) and dressing of face beds and joints, as specified of ranom rubble walling, uncoursed or brought upto courses complete all as specified and as directed

Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc complete all as specified and as directed.

Point wiring for one light /fan/exhaust fan/Bell point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable 1100V grade in and including not less than 2.00 mm thick and 20 mm dia Non metallic Rigid PVC surface/Concealed Conduit ( ISI marked ) with and all accessories 1.5 mm thick mild steel terminal boxes concealed on walls, painting the same inside and out side with one coat of black bitumen paint with 3mm thick hylam brand bakelite sheet cover for fixing of piano switches/sockets/ regulator etc along with PVC insulated and unsheathed FRLS 1.5sqmm multi stranded copper conductor cable (green color) as earth lead, & connected to common earth and earthdolly, making good the disturbed surface to match with the existing specification complete all as specified and as directed by GE. Make: Polycab/ Finolex/ Havells/ HPL

All as per srl item No 111, but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 111, but for 3 pin 5 Amps socket outlet independent board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 111, but for 3 pin 15 Amps socket outlet independent board with cable 2.5 sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

All as per srl item No 111, but for 3 pin 15 Amps socket outlet independent board with cable 4.0 sq mm including copper PVC insulated PVC unsheathed 2.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

S&F for modular switch 6 Amps single pole one way with outer strip complete all as specified and as directed.

S&F for socket combined 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and as directed.

Exhaust fan Ventil Air - DB 300 mm including louver complete all as specified and as directed.

S&F New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W complete all as specified and directed. Make- Havells Cat Part No LHEXBXPNIN1W020 or equivalent to Crompton/ Syska

S&F in replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 10 W complete all as specified and directed. Make- Havells Cat Part No LHEXBXPNIN1W010 or equivalent to Crompton/ Syska

S&F in replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) cat part no. LHEOAOP7UZ6W010 230 Volts wall/surface mounted complete with with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note-MCBs will be measured separately)

S&F in replacement MCB Single Pole, 230 Volt, Rating 6 to 32 Amps complete all as specified and as directed.

S&F in replacement MCB Single Pole and Neutral , 240 Volt, Rating 40 Amps complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES SSR 2009 (Part I) connected to main control board as specified and testing on completion.

Fixing & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 6 Sqmm x 2 core size all as specified including taking down old cable. Note : Earth work and other connected work shall be measured & paid sperately complete all as specified and as directed.

Removing excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

Brick sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed.

Switch piano flush type 5 Amps single pole one way complete all as specified and as directed.

S&F for socket 3 Pin 6 Amps flush type complete all as specified and as directed.

Switch socket combination 2-in-1 pin 5 Amps flush type complete all as specified and as directed.

Switch socket combination 2-in-1, 3 pin 5 & 15 Amps flush type complete all as specified and as directed.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

S&F in replacement MCB Single Pole, 230 Volt, Raiting 6 to 40 Amps complete all as specified and as directed.

S&F in replacement MCB Single Pole and Neutral , 230 Volt, Raiting 40 to 63 Amps complete all as specified and as directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note-MCBs will be measured separately)

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 08 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note-MCBs will be measured separately)

S & F in replacement sheet metal enclosures for DBs when MCBs to be used double door DB VTPN MCCB 125A 4 way IP43 Protection Make: Indoasian, Cat Part No - 811888 with 125A MCCB 16 KA complete all as specified and as directed. Make: Indoasian, Cat Pt No - 830153 or equivalent to Make : Indoasian/Legrand/C&S

S&F single pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of complete all as specified and as directed.

S&F in Replacement of fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Refixing of LED light fitting any type/ any wattage connected with 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Taking down/refixing ceiling fan/Exhaust Fan including disconnection of existing connection, dismanting of blades and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and rehanging the fan complete all as specified and as directed.

LED light fitting 10W bulkhead environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit ledluminaire comprising of high brightness leds Make-Havells Cat Part No - HEXAFT10WLED857SSYMBOPC or equivalent to Philips/ Wipro/ Bajaj complete all as specified and directed.

LED Street light 40W including angle arms (Bracket) with 25mm dia GI pipe. Make Havells Cat Part No - ENDURAPEARLNEOSL40WLED757PASYTOPC or equivalent to Philips/ Wipro/ Bajaj complete all as specified and directed .

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead complete all as specified and as directed Including taking down old sub main wire.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 06 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead complete all as specified and as directed Including taking down old sub main wire.

Taking down unserviceable Ceiling fans and Exhaust fans, sealing cable end, dismantling blade and deposit to MES Yard for a safe custody of a removed fan & geysers with all accessories complete all as specified and as directed,

Supply and fixing high speed Having service value >= 5.0, ceiling fan 1200mm sweep 230 volt AC single phase with all fixing accessories including providing the suitable size of fan hook in the ceiling as per site requirement complete with all suitable electrical point wiring connection complete all as specified and as directed.

Supply and fixing high speed Having service value >= 5.0, ceiling fan 1400mm sweep 230 volt AC single phase with all fixing accessories including providing the suitable size of fan hook in the ceiling as per site requirement complete with all suitable electrical point wiring connection complete all as specified and as directed.

Exhaust fans size 300mm Steel body 230 volt AC single phase complete with louvers including grounting of nut bolts for fixing of Exhaust Fan complete all as specified and as directed.

Exhaust fans size 450mm Steel body 230 volt AC single phase complete with louvers including grounting of nut bolts for fixing of Exhaust Fan complete all as specified and as directed.

Supply and fixing electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified and as directed.

Bell push flush type 5 amp complete all as specified and directed.

Call bell AC, 230 volts, SP complete all as specified and directed. Make - HPL Item Code EASMDB07 or equivalent in Havells (Carbtree)/ Legrand/Phillips/Seimens

Switch button single pole one way 10 Amps 240 volt ( Modular Type ) with outer strip, complete all as specified and as directed. (Note- All modular cover plate/ modular flush Box/Switch/Sockets Incorporated with this, should be in same Make - Havells/ Legrand/ Indoasian

Supply & fixing fan regulator 120W, 230V 50 C/S, delux Modular type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

MAHAJAN TRADING CO

SINGH CONST CO

shri ram dubey

DEV RAJ MAGOTRA