construction of Chowkidar/Driver room and parking at Angling hut Bharmour Distt Chamba HP

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift up to any heights, stacking the excavated soil not more than 3 mtrs. (Three meters) clear from the edge of excavation and then retuning the stacked soil in15cm (Fifteen centimeter)layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-charge,

Providing form work with steel plates 3.15 mm .thick welded with angle iron in frame 30 x 30 x5mm. so as to give a fair finish including centring , shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete workinSides and soffits of beams, beam haunchings , cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing form work with steel plates 3.15 mm .thick welded with angle iron in frame 30 x 30 x5mm. so as to give a fair finish including centring , shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in Foundation , footings basis of columns etc. and mass concrete. including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing form work with steel plates 3.15 mm .thick welded with angle iron in frame 30 x 30 x5mm. so as to give a fair finish including centring , shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like. including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing form work with steel plates 3.15 mm .thick welded with angle iron in frame 30 x 30 x5mm. so as to give a fair finish including centring , shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in Columns, pillars, posts and struts including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing form work with steel plates 3.15 mm (Three point fiftteen milimetres) thick welded with angle iron in frames, Edges of slabs and breaks in floors and walls including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in Lintels, beams girders bressumers and cantilevers upto floor two level. lintal beams including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :Foundations, footings bases of columns and the like and mass concrete. Footings including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and laying cement concrete 1:1.5:3 and curing complete excluding cost of form work Suspended floor roofs landing and shelves and their support balconies, beams, girders, etc.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work inColumn, pillars, posts and struts upto floor two level : including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand: 8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth: including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing mild steel/Tor steel reinforcement for R.C.C. Work including bending, binding and placing in position complete upto floor two level :including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Brick work using Second Class common burnt clay building bricks in foundation and plinth in super structure Cement Mortar 1:6 (1 Cement : 6 Sand) including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Half brick masonry in Second Class common burnt clay building bricks in Cement Mortar 1:3( 1 cement:3 sand) in foundation and plinth in super structure including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing woodwork in frames of doors,windows ,clerestory, windows and other frames wrought,framed and fixed in position.2nd class deodar wood including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals .

Providing and fixing panelled glazed or panelled and glazedshutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws.40mm thick2nd class deodar wood.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. 40 mm thick. 2nd class deodar wood.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing 19mm thick Commercial Board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete) including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing 12mm (twalve millimetre) thick 150mm (one hundred fifty millimetre) wide pelmet with 25 mm (twenty fife millimetre ) diametre wooden curtain rods and brackets including fixing 25x3mm (twenty fife into three millimetre) M.S. flat at 10 cm. (ten centimetres) Long and plugs etcetra complete. First class deodar wood including carriage of material with in all leads and lifts and other incidentals in all heights as directed by the Engineer-in-Charge.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws Plain grill. including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing M.S. single acting spring hinges bright finished with necessary screws etc. complete.150mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete:300x16mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 300x10mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 100x10mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. 125 mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. 100 mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing bright finished hard drawn hooks and eyes.250mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and laying Duro stone vetrified tiles 300x 300mmx 8mm ) in grey/ coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

white glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and notting. Readymixed paint brushing wood primer pink including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Painting two coats (excluding priming coat)on new wood and wood based surfaces,with readymixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign mattersand papering and stopping:-Readymixed paint other then white including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Painting two coats (excluding priming coat)on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and other foreign matter With readymixed paint other than white including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

20mm Cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm ingirth and finished even and smooth. Cement Mortar 1:5 (1 Cement :5 sand) including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

15mm cement plaster in single coat on fair side of brick/ concrete /stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/ or rounded angles not exceeding 80mm in girth and finished even and smooth.Cement Mortar 1:5 (1 Cement :5 sand)

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials. including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

P/F to wall ceiling and floor galvanised mild steel tubes ( Medium grade )tube fittings and clamps including makin good the wall, ceiling and floor:15 mm nominal bore including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by P/F Tee i/c cutting and threading the pipes complete including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

P/F PVC Water storage tank of ISI 12701 marked G.I. Inlet & outlet connection ,15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement i/c hoisting ou to all heights above ground level 1000 litres net capacity tank including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately):-Angle Indian Universal closet including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing 100mm (One hundred millimetre) size 'P' of 'S' trap for water closet ( squating pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1( One Cement : One Sand ) . Sand cast iron .including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing Plastic seat ( solid type) and cover for wash down water closet with C.P. Brass hings and rubber buffers: White plastic seat and cover including carriage of material with in all leads and lifts in all heights including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing PTMT Coloured / white high density polythelene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovr flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) .including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing vitreous china wash basin flat back with single hole for pillar tap with C.I or M.S brackets painted white including holes and making good the same but excluding fittings(i) 630 x 450mm(Six hundred thirty into four hundred fifty millimeters) including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing stainless steel Kitchen sink of approved standard ISI make with drain board and C.P waste C.I. or M.S. brackets painted white i/c cutting holes and making good the same but excluding fitting . 610x460x200mm including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing rubber plug for sink/wash basin. 32mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing C.P. Brass waste for wash basin or sink 32 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing M.I. Union for wash basin or sink 32 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor,gully/Nahini trap. including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing 600x450 mm belevelled edge mirror of superior glass moulded on 6 mm thick A.C. sheet or ply wood and sheet and fixed to wooden plug with CP brass screws and washers . including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing C.P. brass towel rail complete with C.P. brackets fixed to wooden plugs with C.P. brass screws 600mm x 20mm .including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing C.P. brass bib tap with capstan head 15 mm dia meter including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals .

Providing and fixing C.P. brass Pillar tap with capstan head 15 mm dia meter including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing C.P. brass stop cocks 15 mm dia meter including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing G.I./M.I union of 15 mm nominal size including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals .

Providing and fixing PTMT jet spray of approved quality and colour with 1.5 mtr. tube.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing P.V.C connection with brass unions 300/450mm length 15mm nominal bore including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing c.p. brass angle valve 15mm without Nuts and pipe including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals .

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc.complete. 110 mm X 75 mm .including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-Charge and other incidentals.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete.110 mm diaincluding carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete.75 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.110 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.75 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. 110 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. 75 mm dia including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing brass shower rose with 15 mm inlet.100 mm dia.including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Providing and fixing Robe hook (Vitreous China) including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-charge and other incidentals

Constructing man hole with RCC top slab 1:2:4 mix in (One cement:Two sand:Four graded stone aggregqte 20mm (Twenty millimetre nominal size foundation concrete 1:4:8(One cement:Four sand:Eight graded stone aggregat 40mm(forty millimetre) nominal size inside plastering 15mm(Fifteen millimetre) thick with cement mortar 1:3(One cement Three sand) finished with the floating coat of neat cement and makaing channel cement concrete 1:2:4 mix(One cement:Two sand:Four graded stone aggregqte 20mm(Twenty millimetre) nominal size finished smooth complete curing and testing inside size 800x800mmx500 mm(Eight hundred into eight hundred into five hundred milimetre metre) deep including C.I. cover with frame(Light duty single pattern 450x610mm(Four hundred fifty into six hundred ten millimetre) internal dia metre total weight of cover and frame to be not less then 38 kg(Thirty eight kilogram) (weight of cover 23 kg(Twenty three kilogram) and wreight of frame is 15 kg (Fifteen kilogram) with 200mm(two hundred millimetre thick wall of brick masonry common brunt clay building bricks cement mortar 1:3(One cement:Three sand) .including carriage of material with in all leads and lifts in all heights as directed by the Engineer-in-Charge and other incidentals .

ANIL KUMAR

Ankush Kumar