Construction of Taluka Level Central Administrative Building at Mahad District Raigad

Providing and laying cast in situ/Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 600mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in-charge including placing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete.(Excluding steel reinforcement) (Item No. 22.29)

CAPPING BEAM-Capping beam for piles: Providing and laying Cast in situ/Ready Mixcement concrete M-35 of trap/granite/quartzite/gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.56)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/granite/quartzite/gneiss metal for foundation and bedding/steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 24.04)

Providing preconstructional antitermite treatment as per I.S. 6313(Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. (Item No. 21.22)

Providing preconstructional antitermite treatment as per I.S. 6313(Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper. (Item No. 21.24)

Providing preconstructional antitermite treatment as per I.S. 6313(Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30-60cm deep at 15cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper. (Item No. 21.25)

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15cm to 20cm including watering and compaction etc. complete. (Item No. 21.37)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.54)

... (Item No. 25.54, First Floor)

... (Item No. 25.54, Second Floor)

... (Item No. 25.54, Third Floor)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.35)

... (Item No. 25.35, First Floor)

... (Item No. 25.35, Second Floor)

... (Item No. 25.35, Third Floor)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.74)

... (Item No. 25.74, First Floor)

... (Item No. 25.74, Second Floor)

... (Item No. 25.74, Third Floor)

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/granite/quartzite/gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.07)

... (Item No. 26.07, First Floor)

... (Item No. 26.07, Second Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/quartzite/granite/gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete.(Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.26)

... (Item No. 26.26, First Floor)

... (Item No. 26.26, Second Floor)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.19)

... (Item No. 26.19, First Floor)

... (Item No. 26.19, Second Floor)

Providing and fixing in position HCRM/CRS(Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (Item No. 26.34)

... (Item No. 26.34, First Floor)

... (Item No. 26.34, Second Floor)

... (Item No. 26.34, Third Floor)

Waterproofing Treatment to new Toilet/bathroom by using Polymeric Cementitious Membrane as approved by Engineer in charge, followed by 112mm thick brick bat coba covered with 20mm mortar finish. If there are cracks on the bare slab, open the crack in V Groove and fill it with ready to use repair polymer modified mortar based on special cements, aldehyde based polymers with thixotropy modifying agents. If there are lots of honeycombs and identified bad patches of concrete the same should be grouted as per the instructions of site incharge.(The grouting shall be paid separately). Clean the entire surface thoroughly and over this prepared surface, apply three coats of polymeric Cementitious waterproofing coating having a non-toxic, 2-(methoxycarbonyl)-1-propene-Butyl-2 propenoate(MPBP) based polymeric waterproofing solution as approved by Engineer in charge. Provide and lay 112mm average thicknes of brick bat coba in cement mortar 1:5 over 12mm thickCM 1:3 bedding with one pouch of 330 grams of thorough blend of special cements, aldehyde based polymers, shrinkage compensating agents as approved by Engineer in charge per 50 Kg bag of cement and finishing with 20mm thick cement plaster in cement mortar 1:3 by mixing one 330 grams pouch of above admixture per 50 Kg bag of cement, including all lead, lifts and laid to proper slope to drain off water entirely preparing bell mouth including watta, beveled or champhered portion at the junction of wall and work up to a height of 300mm or as directed and including finishing the top layer of waterproofing treatement with false marking of 30cm x 30cm or as directed, curing and covering the whole treatment. MPBP Polymeric Waterproofing Coating for Concrete and Masonry should have following minimum properties:1) Elongation %(ASTM D412-2016): @ 100% 2) Tensile Strength N/mm2(ASTM D412-2016): 3.3 3) Specific Gravity: 1.02 ± 0.02 4) Total Solids(ASTM D1644-2012): 43.98 5) Hardness Shore A(ASTM D2240-2015): 82 (Item No. 52.13)

... (Item No. 52.13, First Floor)

... (Item No. 52.13, Second Floor)

... (Item No. 52.14, Third Floor)

Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete (Item No. 27.05)

... (Item No. 27.05, First Floor)

... (Item No. 27.05, Second Floor)

... (Item No. 27.05, Third Floor)

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. (Item No. 32.04)

... (Item No. 32.04, First Floor)

... (Item No. 32.04, Second Floor)

... (Item No. 32.04, Third Floor)

Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete. (Item No. 32.15)

... (Item No. 32.15, First Floor)

... (Item No. 32.15, Second Floor)

... (Item No. 32.15, Third Floor)

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. (Item No. 32.32)

... (Item No. 32.32, First Floor)

... (Item No. 32.32, Second Floor)

... (Item No. 32.32, Third Floor)

Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity.(With prior approval of S.E.) (Item No. 36.20)

... (Item No. 36.20, First Floor)

... (Item No. 36.20, Second Floor)

... (Item No. 36.20)

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete. (Item No. 35.24)

... (Item No. 35.24, First Floor)

... (Item No. 35.24, Second Floor)

... (Item No. 35.24, Third Floor)

Providing waterproof plaster in W.C. and bath 20mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing(and filling joints of Nahani trap and any outlet by properly) etc. complete. (Item No. 31.07)

... (Item No. 31.07, First Floor)

... (Item No. 31.07, Second Floor)

Providing water proof bedding for flooring of Bath and WC 25mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/-including ponding test etc. complete. (Item No. 31.05)

... (Item No. 31.05, First Floor)

... (Item No. 31.05, Second Floor)

Providing and laying in position flooring of telephone black/Amba White/Cat bary brown/Ruby red/Ocean Brown granite stone of approved shade and size 18mm to 20mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. (Item No. 33.34, First Floor)

... (Item No. 33.34, Second Floor)

Providing and laying telephone black/Amba White/Cadburybrown/Ruby red/Ocean Brown granite stone of 18 to 20mm thick for door frame/dado/window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. (Item No. 33.68)

... (Item No. 33.68, First Floor)

... (Item No. 33.68)

Providing and laying vitrified mirror/glossy finish tiles decorative type having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS. 15622-2006(group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. (Item No. 33.40, First Floor)

... (Item No. 33.40, Second Floor)

Providing and laying vitrified mirror/glossy finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS. 15622-2006(group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete (Item No. 33.41)

... (Item No. 33.41, First Floor)

... (Item No. 33.41, Second Floor)

Providing and fixing machine cut machine polished 18mm to 20mm thick telephone black/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. (Item No. 33.35)

... (Item No. 33.35, First Floor)

... (Item No. 33.35, Second Floor)

... (Item No. 33.35, Third Floor)

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600mm x 450mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30mm thick supports with kadappah top 35 to 40mm thick and polished granite 16 to 20mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15cm height and top granite of 75 x 40cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete.(Platform top size 5.00m x 0.60m and height is 0.75 m) (Item No. 41.78, First Floor)

Providing and laying Antiskid Ceramic tiles of approved quality of size 30cm x 30cm and confirming to IS 15622-2006(Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. (Item No. 33.67)

... (Item No. 33.67, First Floor)

... (Item No. 33.67, Second Floor)

Providing and laying ceramic tiles having size 30cm. x 60cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/colour cement slurry cleaning curing etc. complete. (Item No. 33.27, First Floor)

Providing and fixing machine cut mirror polished 18mm to 20mm thick telephone black granite/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish (Item No. 33.36)

... (Item No. 33.36, First Floor)

... (Item No. 33.36, Second Floor)

Providing and fixing solid core flush door shutter in single leaf 32mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. (Item No. 39.09)

... (Item No. 39.09, First Floor)

... (Item No. 39.09, Second Floor)

Providing and fixing solid core flush door shutter commercial in single leaf 32mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete. (Item No. 39.10)

... (Item No. 39.10, First Floor)

... (Item No. 39.10, Second Floor)

Providing and fixing Country cut teak wood double or single leaf second class fully panelled door shutter with 35mm thick style and rail with 25mm thick panels with openable fan light as per detailed drawings. Excluding the door frame 60mm x 100mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats.(Excluding the door frame) (Item No. 39.04)

... (Item No. 39.04, First Floor)

... (Item No. 39.04, Second Floor)

Providing and fixing fiber glass reinforced polyster door shutter 30mm thick as per IS 14856(2000)(Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete (Item No. 39.58)

... (Item No. 39.58, First Floor)

... (Item No. 39.58, Second Floor)

Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 Kilogram. to 20 Kilogram. Per Sq.m.) Spec.number: As directed by Engineer-in-charge. (Item No. 23.09)

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38mm x 1.22mm box type, 5mm thick sheet glass louvers, of approved quality etc. complete. (Item No. 39.68)

... (Item No. 39.68, First Floor)

... (Item No. 39.68, Second Floor)

Providing and fixing in position(as per 1868/1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90mm at weight 0.637 Kilogram/running metre. with window frame bottom track section 92 x 31.75 x 1.30mm at weight 1.070 Kilogram/running metre.. Top and side track section 92 x 31.75 x 1.30mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25mm at weight 0.417 Kilogram/running metre. Inter locking section 40 x 18 x 1.10mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box (Item No. 39.44)

... (Item No. 39.44, First Floor)

... (Item No. 39.44)

Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/square metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. (Item No. 40.02)

... (Item No. 40.02, First Floor)

... (Item No. 40.02, Second Floor)

Providing and Fixing mat finish stainless steel(of 302 grade) railing with top pipe of 50mm dia. and vertical pipe of 38mm dia at 0.60m c/c or as required and horizontal pipes of 25mm dia in three rows, all pipes of 2mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75mm dia above newel post of 75mm diameter etc. complete(Prior approval of sample and brand by Ex.Engineer is necessary before use) (Item No. 40.08, First Floor)

... (Item No. 40.08, Second Floor)

Providing and laying in trenches 50mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.66)

Providing and fixing on walls/ceiling/floor 15mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.55)

... (Item No. 42.55, First Floor)

... (Item No. 42.55, Second Floor)

Providing and fixing on walls/ceiling/floor 20mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.56)

... (Item No. 42.56, First Floor)

... (Item No. 42.56, Second Floor)

Providing and fixing on walls/ceiling/floor 32mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.58)

... (Item No. 42.58, First Floor)

... (Item No. 42.58, Second Floor)

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (Item No. 42.87)

Providing and fixing 100mm dia stabiliser pipe/P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. (Item No. 42.52)

Providing and fixing 15mm dia. screw down bib/stop tap of brass including necessary socket union nut complete. (Item No. 41.40)

... (Item No. 41.40, First Floor)

... (Item No. 41.40, Second Floor)

Providing and fixing screw down for 20mm dia. wheeled stop tap of brass including necessary sockets/union nut complete. (Item No. 41.44)

... (Item No. 41.44, First Floor)

... (Item No. 41.44, Second Floor)

Providing and fixing screw down for 50mm dia. wheeled stop tap of brass including necessary sockets/union nut complete. (Item No. 41.48)

Providing and fixing orissa type colour glazed earthenware 625 x 450mm. w.c. pan including trap, C.I. soil and vent pipe upto the out side face of wall including 100mm. dia. C.I. plug, bend, 15mm. thick 10 litre PVC flushing cistern with all necessary pipe connection etc. complete. (Item No. 42.35)

... (Item No. 42.35, First Floor)

... (Item No. 42.35, Second Floor)

Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32mm size of approved make including soil pipe, vent pipe up to outside face of wall, 100mm dia. G.I. plug bend inlet pipe all fittings, cuttingand making good walls, floors etc. complete. (Item No. 42.86)

... (Item No. 42.86, First Floor)

... (Item No. 42.86, Second Floor)

Providing and fixing 100mm dia. chromium plated brass showers rose to 15mm dia. supply pipe including necessary bend and socket complete. (Item No. 41.51)

Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. (Item No. 41.63)

Providing and fixing 15cm rigid PVC Nahani trap including PVC grating, bend, connectingpiece of UPVC pipe up to the outside face of wall, making the good damaged surface and testing etc. complete(Prior approval of sample and brand by Ex. Engr. is necessary before use) (Item No. 43.18)

... (Item No. 43.18, First Floor)

... (Item No. 43.18, First Floor)

Providing, constructing and fixing 450mm dia. Inspection chamber made up of Polypropylene/polyethylene material of thickness 3.5mm and height of 388mm with 160 or 200mm main inlet(s) outlet and 110 and/or 160mm branch inlets, with 450mm dia. Ultra shaft pipe of HDPE material having height of 460mm, having R.C.C. cover and frame fixing in 150mm thick in c.c.1:2:4, having crushed sand bed of 150mm thick of size 750mm dia. Including excavation and refilling the sides of chamber by sand crushed cushioning 150mm thickness, connecting all required UPVC fittings with rubber lubricant etc. complete. (Item No. 43.28)

Providing, constructing and fixing 600mm dia. Inspection chamber made up of Polypropylene/polyethylene material Having 315mm diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160mm and 200mm pipes having thickness of 5mm and 600mm in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5mm having R.C.C. cover and frame fixing in 150mm thick in c.c.1:2:4, having crushed sand bed of 150mm thick of size 750mm dia. Including excavation and refilling the sides of chamber by ?sand crushed cushioning 150mm thickness, connecting all required UPVC fittings with rubber lubricant etc.complete. (Item No. 43.29)

Providing, constructing and fixing 250mm dia. Inspection chamber made up of UPVC material of thickness 3.5mm and height of 259mm with inlet and outlet of 110mm dia. with 75mm dia. U Trap, Ultra shaft pipe of Upvc material having height of 470mm and fixing Ultra 250mm dia. UPVC cover and frame in 150mm thick in c.c.1:2:4, having crushed sand bed of 100mm thick of size 550mm dia. Including excavation and refilling the sides of chamber by crushed sand cushioning 150mm thickness, connecting all required UPVC fittings with rubber lubricant etc. complete. (Item No. 43.27)

Providing and fixing chromium plated towel rod 16mm dia and 75cm. in length including all accessories complete. (Item No. 42.31)

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. (Item No. 42.20)

Providing and fixing 45cm wide mild steel ladder of 40mm x 6mm mild steel flat stringers and steps of 18mm dia. mild steel bar for water tank including fixing it in(1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete.(Anti Corossive Paint) (Item No. 41.56)

Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.) With fine aggregate(Crushed sand VSI Grade) (Item No. 24.16)

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25mm, , cement content not to be less than 150kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor/by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.13)

Providing and laying in situ cement concrete M-30 with tremix treatment for 200mm thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen(excluding reinforcement) with coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.22a)

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift upto 1.5m.) By Mechanical Means (Item No. 21.02)

Providing and laying in situ/ready mix M-25 controlled reinforced cement concrete of trap metal for raft slab including "V" haunches, formwork, scaffolding, compaction by vibrating, finishing curing etc. complete. concrete batch mix plant/pan mixer with fine agreegates of required specifications(VSI sand finely washed etc) etc. complete.(excluding reinforcement). a) RCC Grade with reversible drum type mixer/concrete batch mix plant(pan mixer) . (Item No. 17.33)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.19)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.72)

Providing and fixing in position TMT-FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (Item No. 26.33)

Providing & Fixing in position, Acoustical Panelling made from Fabric wrapped Compressed polyester fibre nonwoven 9mm panels on, 50 x 50mm sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 gsm synthetic wool 50mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings/finishing-items/paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour, finishing etc complete (Item No. 51.01)

Providing and fixing white glazed earthenware lipped flat back/corner type Urinal with PVC 5 liters flushing cistern with fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32mm diameter P.V.C. flush pipe with fitting including lead soil pipe, lead trap and soil pipe connection up to the outside face of wall. (Item No. 41.60)

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift upto 1.5m.) By Mechanical Means (Item No. 21.02)

Providing dry/trap/granite/quartzite/gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete. (Item No. 21.38)

Providing and laying in situ/ready mix/ready mix M10 cement concrete of trap/granite/quartzite/gneiss metal in foundation including necessary centering, formwork, bailing out water, compacting and curing etc. complete.(with fully automatic micro processor based PLC with SCADA enabled with reversible drum type mixer/concrete batch mix plant(pan mixer) with natural/artifical sand) (Item No. 12.25)

Providing cast in situ/ready mix M20 grade cement concrete for head walls of CD work/retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete.(with reversible drum type mixer/concrete batch mix plant(pan mixer) with SCADA (Item No. 11.29)

Providing and laying of filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2 of MoRTH specifications to a thickness of not less than 600mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition as per drawing and technical specifications etc. complete. (Item No. 12.72)

Back filling behind abutment, wing wall and return wall as per drawings and technical specifications etc. complete.(by granular material) (Item No. 12.70)

Providing and laying weep holes of 100mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete. (Item No. 17.37)

Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete (Item No. 27.05)

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. (Item No. 32.32)

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete. (Item No. 35.24)

Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete(Material obtained from Other sources) (Item No. 2.28)

Providing dry/trap/granite/quartzite/gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete. (Item No. 21.38)

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25mm, , cement content not to be less than 150kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor/by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.13)

Providing and laying in situ cement concrete M-30 with tremix treatment for 200mm thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4mm wide and 20mm deep with necessary refilling with polysuphide sealent(Pouring grade) confirming to BS : 5212-1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter(excluding reinforcement) with coarsen and fine aggregate Using V.S.I.Quality Artifitial Sand etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.22b)

Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/colour of 2.5mm thick including 1.5 Refractive index reflectorizing glass beads @ 250gm/sqm .Thickness of 2.5mm is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/sqm/lux measured in the initial 7 days and sustained reflectivity RL of 100 mcd/sqm/lux and Qd of 100 mcd/sqm/lux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015). (Item No. 6.12a)

Supplying and Fixing of Molded Shank Raised Pavement Markers/Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50mm, 100mm and 102 +/-2mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/-2mm and height not less than 30+/-2mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer. (Item No. 6.09)

Providing and fixing road junction/information sign boards of size 1.80 x 0.90 Meter Prepared 16 guageM.S.sheet on frame of M.S.angle of size 35 x 35 x 5mm with cross bracing of size 35x35x5mm including painting with one coat of zinc cromate stoving primer and two coats each of green/white back ground and back side gray stove enamelled, bonded with red retro reflective sheet Engineering grade, border/letters/numeral/arrows, coated with non pealable crystal clear protective transperent coat retaining 100% reflection including two angle iron post of size 65 x 65 x 6mm of 3.65m. long inflated at bottom, drilled on top and painted in white and black bands of 30cm. with 4 Nos. high strength G.I. bolts and nuts of size 10mm dia. and 20mm long. Sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60cm x 60cm x 75cm size as directed by Engineer-in-charge etc. complete. Mild Steel Board with Engineering Grade. (Item No. 6.41)

Road Delineators: Supplying and installation of delineators(Roadway Indicators, Hazard markers, Object markers) 80 to 100cm high above ground level, painted black and white in 15cm wide strips, fitted with 80x100mm rectangular or 75mm dia. Circular reflectorised panels at the top, buried or pressed into the ground and confirming to I.R.C. 79 and the drawings (Item No. 6.15)

Metal Beam Crash Barrier -- Type-A, W : Metal Beam Crash Barrier(Providing and erecting a W metal beam crash barrier comprising of 3mm thick corrugated sheet metal beam rail, 70cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5mm spaced 2m centre to centre, 1.8m high, 1.1m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5mm, 330mm long complete as per clause 810)" (Item No. 7.30)

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift upto 1.5m.) By Mechanical Means (Item No. 21.02)

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/murum watering, ramming etc. complete.(Lift upto 1.5 m). By Mechanical Means (Item No. 21.20)

Providing and laying in situ/ready mix M-25 controlled reinforced cement concrete of trap metal for raft slab including "V" haunches, formwork, scaffolding, compaction by vibrating, finishing curing etc. complete. concrete batch mix plant/pan mixer with fine agreegates of required specifications(VSI sand finely washed etc) etc. complete.(excluding reinforcement). a) RCC Grade with reversible drum type mixer/concrete batch mix plant(pan mixer) . (Item No. 17.33)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.19)

Providing and laying in situ/ready mix M-25 controlled cement concrete of trap/granite/quartzite/gneiss metal for RCC work in solid/deck slab etc. including ramming, vibrating, curing, formwork, centering and finishing in cement plaster excluding reinforcement etc. complete.(with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant/pan mixer and fine agreegates of required specifications(VSI sand finely washed etc) i) Height up to 5 m, normal rate. ii) Height 5 to 7.50 m, add 5 percent extra over basic rate. iii) Height 7.50 to 10 m, 7.50 percent extra. iv) Over 10m Height, add 10 percent extra for every 2.50m rise. (Item No. 14.15)

Providing, cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete. (Item No. 14.01)

Electrical Work Portion Est. No. RAESD/OW/ 128 /2024-25 (Sub work -1) Sub-Work No -1 Providing Internal & External EI at Central Administrative Building Mahad, Dist-Raigad Supplying and erecting 25 MeterMeter dia. corrugated flexible polypropylene conduit

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 MeterMeter with accessories on wall/ceiling as per specification No: WG-METERA/CON.

Supplying and laying HMETERS PVC conduit FRLS grade 25 MeterMeter dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-METERA/CC.

Supplying and erecting HMETERS PVC conduit FRLS grade 25 MeterMeter dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-METERA/CC.

Supplying and erecting HMETERS PVC conduit FRLS grade 32 MeterMeter dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-METERA/CC.

Supplying and erecting PVC slotted box trunking of size 100x100 MeterMeter. with accessories on wall/ceiling as per specification No: WG-METERA/SLBOX.

Supplying and erecting Meterains with 2x1.5 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-METERA/BW

Supplying and erecting Meterains with 1x1.5 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-METERA/BW

Supplying and erecting Meterains with 2x2.5 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-METERA/BW

Supplying and erecting Meterains with 1x2.5 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-METERA/BW

Supplying and erecting Meterains with 2x4 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-METERA/BW (extra for lead wire)

Supplying and erecting Meterains with 4x4 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-METERA/BW

Supplying and erecting Meterains with 1x4 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-METERA/BW

Supplying 16 aMeterp. 3 pin plug Top bakelite type of 230 V. A.C. supply.

Supplying and erecting Meterodular type switch 6A / 10A duly erected on provided plate and box with wiring connections coMeterplete.

Supplying and erecting Meterodular type switch one way 16 / 20 A, duly erected on provided plate and box with wiring connections coMeterplete with neon indicator.

Supplying and erecting Meterodular type 3 pin 6A Meterulti socket with safety shutter, duly erected on provided plate and box with wiring connections coMeterplete.

Supplying and erecting Meterodular type 3 pin 6 / 16A Meterulti socket with safety shutter, duly erected on provided plate and box with wiring connections coMeterplete.

Supplying and erecting Meterodular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections coMeterplete.

Supplying and erecting Meterodular type coMeterputer Jack RJ45 with safety shutter, duly erected on provided plate and box with wiring connections coMeterplete.

Supplying and erecting Meterodular type (two Meterodule) electronic step regulator for fan, duly erected on provided plate and box with wiring connections coMeterplete.

Supplying and erecting unbreakable concealed type Meterodular switch box with double Meterounting plate for 1 Meterodule duly erected flush to wall with required chiselling and finishing with ceMeterent Meterortar / POP as per required to Meteratch the background.

Supplying and erecting unbreakable concealed type Meterodular switch box with double Meterounting plate for 2 Meterodule duly erected flush to wall with required chiselling and finishing with ceMeterent Meterortar / POP as per required to Meteratch the background.

Supplying and erecting unbreakable concealed type Meterodular switch box with double Meterounting plate for 3 Meterodule duly erected flush to wall with required chiselling and finishing with ceMeterent Meterortar / POP as per required to Meteratch the background.

Supplying and erecting unbreakable concealed type Meterodular switch box with double Meterounting plate for 6 Meterodule duly erected flush to wall with required chiselling and finishing with ceMeterent Meterortar / POP as per required to Meteratch the background.

Supplying and erecting unbreakable concealed type Meterodular switch box with double Meterounting plate for 12 Meterodule duly erected flush to wall with required chiselling and finishing with ceMeterent Meterortar / POP as per required to Meteratch the background.

Supplying and erecting 16 to 32 A, 10kA, DPMETERCB suitable to fix in 2 Meterodule of Meterodular switch in provided box coMeterplete & duly concealed with necessary Meteraterial and connected.

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.MeterMeter (2+1E) FRLSH grade copper wire, Meterodular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for light/bell concealed type in Meterin 20 MeterMeter FRLS grade HMETERS PVC conduit with 1.5 sq.MeterMeter. (2+1E) FRLSH grade copper wires, Meterodular type switch, earthing and required accessories as per specification No: WG-PW/CW

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in Meterin 20 MeterMeter PVC conduit / casing n capping with 1.5 sq.MeterMeter. (2+1E) FRLSH grade copper wires, Meterodular type switch, earthing and required accessories as per specification No: WG-PW/HW

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in Meterin 20 MeterMeter PVC conduit / casing n capping with 1.5 sq.MeterMeter. (2+1E) FRLSH grade copper wires, Meterodular type switch, earthing and required accessories as per specification No: WG-PW/HW

Point wiring for ceiling fan concealed type in Meterin 20 MeterMeter FRLS grade HMETERS PVC conduit with 1.5 sq.MeterMeter. (2+1E) FRLSH grade copper wires, Meterodular type switch, earthing and required accessories as per specification No: WG-PW/CW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with Meterodular accessories as per specification No: WG-PW/CW

Supplying & erecting 2 pair telephone copper cable 0.5 MeterMeter dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforMetering to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 10 pair telephone copper cable 0.5 MeterMeter dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforMetering to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 0.5 MeterMeter dia, copper juMeterper wire as per specification No. WG-TW

Supplying, erecting & coMeterMeterissioning 10 pairs FR junction box with Meteroulded plastic enclosure as per specification no. WG-TW

Supplying and installing cat-6 STP cable suitable for networking coMeterplete as per specification.

Supplying and fixing 3 Meter UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet Meteranaged switch with web view/CLI, 6KV surge protection on ethernet port and console port for MeteranageMeterent in provided rack as per specification no. WG-NWC/GBS

Supplying, fixing, and configuring 8-ports Meteranaged gigabit, Layer-2 switch, 10/100/1000 base-T, POE sMeterart switch plus 2 SFP erected in provided rack coMeterplete.

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided Meterodular box as per specification no. WG-NAS/IO

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack coMeterplete as per specification no. WG-NAS/PP

Supplying and fixing 6U wall Meterount rack (DiMeterension-DxWxH – 500x600x367 MeterMeter) as per specification No. WG-NAS/RAK

Supplying and erecting LED Panel Light(600MeterMeter X 600MeterMeter) METERax. 30 W having CRCA powder coated housing, polystyrene diffuser having systeMeter luMeterens output of METERin. 3600 LuMeterens, Meterin. efficacy of 120 luMeteren/W, CRI>80, CCT upto 6500K, BeaMeter Angle of 120 deg., Meterax. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having Meterounting arrangeMeterent with board for surface type or spring loaded Meterounting clips coMeterplete with 3 years warranty.

Supplying and erecting LED Panel Light(600MeterMeter X 600MeterMeter) METERax. 35 W having CRCA powder coated housing, polystyrene diffuser having systeMeter luMeterens output of METERin 4200 LuMeterens, Meterin. efficacy of 120 luMeteren/W, CRI>80, CCT upto 6500K, BeaMeter Angle of 120 deg., Meterax. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having Meterounting arrangeMeterent with board for surface type or spring loaded Meterounting clips coMeterplete with 3 years warranty.

METERaking suitable size of recess in any type of false ceiling for erection of flush type LED panel light 600MeterMeter x 600MeterMeter/1200x300MeterMeter and finishing the background to Meteratch the original ceiling surface.

Supplying and erecting anodized aluMeteriniuMeter corridor / passage / Meterirror light LED fitting (2 feet) METERax. 12W with high transitivity diffuser with Meterin. systeMeter luMeterens output of 1200 luMeterens, Meterin. efficacy of 100 luMeteren/W, CRI>80, CCT upto 6000K, BeaMeter Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting anodized aluMeteriniuMeter corridor / passage light LED fitting (4 feet) METERax. 22W with high transitivity diffuser with systeMeter luMeterens output of METERin.2200 luMeterens , Meterin. efficacy of 100 luMeteren/W, CRI>80, CCT upto 6000K, BeaMeter Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting luMeterinous / Meterodular type call bell indicator with plastic body, heavy duty coil and indicator laMeterp working on 230V A.C. supply with resetting arrangeMeterent coMeterplete erected on double wooden/ sunMeterica board.

Supplying & erecting 5W-7W, 230V integral type LED LaMeterp suitable for B-22 / E-27 base.

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 MeterMeter coMeterplete erected in position as per specification no. FG-FN/CF

Supplying and erecting ‘B’ class G.I .pipe / METER.S. pipe down rod duly painted for fan coMeterplete erected with PVC three core flexible cable 1 sq. MeterMeter copper PVC wire.

Supplying and erecting fresh air cuMeter exhaust fan of light duty 250 V A.C. 50 cycles 225MeterMeter. 1400 RPMETER rust proof body & blades, wire Meteresh, duly erected, coMeterplete.

Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 450 MeterMeter. 1400 RPMETER coMeterplete erected in position as per specification no. FG-FN/EXF

Supplying and erecting Meteridget type 3.0 litres instant type water heater of rustproof & shockproof ABS plastic body, high grade SS inner tank & 3kW heating eleMeterent with corrosion & hard water protection, with MeteriniMeteruMeter 3 safety protections (i.e. therMeterostat & therMeteral cut-out, function valve) coMeterplete with 6.5 bar pressure withstanding capacity 230/250V, 50Hz, A.C. supply with inlet and outlet, with 3 core PVC flexible copper wire leads duly tested and Meterarking sr. no. and date of erection coMeterplete.

Providing fiber reinforced PVC flexible pipe upto 1Meter length with brass locking nuts and washers and clips at both ends suitable for hot water and cold water both (1 set of 2 nos.) coMeterplete.

Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV gerMetericidal tube of 8W capacity choke Meterade of copper wire and two indicator laMeterps with output of purified water MeteriniMeteruMeter 0.33 litre/Meterin with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication systeMeter .(for TDS Meterore than 200)

Supplying, erecting, testing and coMeterMeterissioning self contained water cooler 230/250V 50Hz noMeterinal cooling capacity of 40 litres per hour and storage capacity 80 litres with partially stainless steel body As per specification no. APWCR/ WC

Supplying and erecting 16/20 MeterMeter (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 2.0 MeterMeter conforMetering to IS 15778 (CTS Series) with necessary CPVC fittings and solvent ceMeterent for Solar Water Heater SysteMeter as per specification No. ESD-HWP/CPVC

Supplying and erecting 25 MeterMeter dia. gun Meteretal sluice valve at position with necessary Meteraterials coMeterplete.

Supplying, installing, testing and coMeterMeterissioning of single phase, 230V, 50 Hz, 1400 to 1600VA digital pure sine wave inverter with backup tiMetere of 1.5 hrs. based on Insulated Gate Bipolar Transistor (IGBT) technology coMeterplete as per specification no. AP-INV

Supplying, installing, testing and coMeterMeterissioning of single phase, 230V, 50 Hz, 2500 VA digital pure sine wave inverter with backup tiMetere of 1.5 hrs. based on Insulated Gate Bipolar Transistor (IGBT) technology coMeterplete as per specification no. AP-INV

Supplying and erecting 12V/150Ah tubular battery with battery terMeterinal wire, duly charged with 36 Meteronths warranty coMeterplete.

Supplying, erecting, testing and coMeterMeterissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS, with backup tiMetere of 1 hrs. PWMETER & IGBT based, with 0.8 to unity output pf coMeterplete with all protections as per specification no. AP-UPS

Supplying, erecting, testing and coMeterMeterissioning of 2kVA capacity online pure sine wave, with backup tiMetere of 1 hrs. PWMETER & IGBT based UPS with 0.8 to unity output pf, single phase input & 1 phase output coMeterplete with all protections as per specification no. AP-UPS

Supplying and erecting 12V/42Ah SMETERF battery with battery terMeterinal wire, duly charged with 24 Meteronths warranty coMeterplete

Supplying, erecting & Meterarking SPMETERCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB

Supplying, erecting & Meterarking SPMETERCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB

Supplying, erecting & Meterarking TPMETERCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB

Supplying, erecting & Meterarking TPMETERCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB

Supplying, erecting & Meterarking FPMETERCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoMetering and 2 ways (2 poles) for outgoing SP METERCBs, with door, 1.2MeterMeter thickness surface / flush Meterounted, IP 43 Protection on iron / GI fraMetere as per specification no. SW-SWR/METERCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoMetering and 6 ways (6 poles) for outgoing SP METERCBs, with door, 1.2MeterMeter thickness surface / flush Meterounted, IP 43 Protection on iron / GI fraMetere as per specification no. SW-SWR/METERCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMETERCB of 4 ways/phase (12 poles), with door, 1.2MeterMeter thickness, surface/flush Meterounted, IP 43 protection on iron/GI fraMetere (horizontal busbar type) as per specification no. SW-SWR/METERCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP METERCBs total 8 ways /24 poles, with door, 1.2MeterMeter thickness surface/flush Meterounted, IP 43 Protection on iron/GI fraMetere (vertical busbar type) as per specification no. SW-SWR/METERCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole METERCCB as incoMeterer & outgoing SP METERCB (36 poles) or TP METERCB of 12 ways (36 poles), with door, 1.2MeterMeter thickness, surface/flush Meterounted, on iron/GI fraMetere (vertical busbar type) as per specification no. SW-SWR/METERCBDB1

Supplying, erecting & coMeterMeterissioning 2 pole RCCB 16/25A, electroMeteragnetic type with 30/100/300 MeterA sensitivity with earth leakage trip indication coMeterplete as per specification no. SW-RCCB/RCCB

Supplying, erecting & coMeterMeterissioning 2 pole RCCB 40A, electroMeteragnetic type with 30/100/300 MeterA sensitivity with earth leakage trip indication coMeterplete as per specification no. SW-RCCB/RCCB

Supplying, erecting & coMeterMeterissioning 2 pole RCCB 63A, electroMeteragnetic type with 30/100/300 MeterA sensitivity with earth leakage trip indication coMeterplete as per specification no. SW-RCCB/RCCB

Providing, erecting & coMeterMeterissioning 4 pole RCCB 40A, with added iMeterMeterunity to avoid DC pulse tripping with 30/100/300 MeterA sensitivity coMeterplete as per specification no. SW-RCCB/RCCB

Providing, erecting & coMeterMeterissioning 4 pole RCCB 100A, with added iMeterMeterunity to avoid DC pulse tripping with 30/100/300 MeterA sensitivity coMeterplete as per specification no. SW-RCCB/RCCB

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V, 2 core 4 sq MeterMeter copper conductor coMeterplete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V, 2 core 6 sq. MeterMeter. copper conductor coMeterplete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V, 4 core 10 sq. MeterMeter. copper conductor coMeterplete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V, 4 core 35 sq. MeterMeter. copper conductor coMeterplete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cMeter coMeterplete with all Meteraterials, testing & recording the results as per specification no. EA-EP

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.MeterMeter (30 no. x 0.25 MeterMeter dia.) 3 core flexible Meterulti stranded copper Industrial cable for voltage grade up to 1.1 kV

Providing & erecting 6 Meter high (clear height) galvanised octagonal pole with foundation bolts having bottoMeter of 130 MeterMeter A/F, top 70 MeterMeter A/F on provided foundation as per specification no. OH-PL/OPL

METERaking METER- 20 grade reinforced ceMeterent concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.Meter at 1.5 Meter depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of teMeterplate, duly plastered as per design coMeterplete (for 6Meter to 8Meter high octagonal /conical GI pole).

Supplying and erecting integrated LED street light fitting 26 to 30W IP65 & IK08 class having single piece pressure die-cast aluMeteriniuMeter housing , having systeMeter luMeterens output of METERin. 2600 LuMeterens, Meterin. efficacy of 100 luMeteren/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver coMeterplete with 3 Years warranty as per specification No FG-ODF/FLS2.

Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluMeteriniuMeter housing, having systeMeter luMeterens output of METERin. 6600 LuMeterens, Meterin. efficacy of 110 luMeteren/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver coMeterplete with 3 Years warranty as per specification No FG-ODF/FLS2.

Supplying & erecting FRP box of size 150MeterMeter x 125MeterMeter x 100 MeterMeter, 2.7 MeterMeter thick coMeterplete on pole/wall as per specification No. CB-SB

Supplying, erecting & Meterarking SPMETERCB 0.5A to 5A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V 2 core 4 sq. MeterMeter. aluMeteriniuMeter conductor coMeterplete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V, 4 core 4 sq. MeterMeter. aluMeteriniuMeter conductor coMeterplete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and erecting Street light bracket for erection of Single fitting Meterade froMeter 40 MeterMeter. dia ‘B’ class G.I. pipe 1.0 Meter. in length along with pole cap of 300 MeterMeter length 100 MeterMeter dia duly welded as per specification no. FG-BKT/BPC

Supplying and erecting street light Wall bracket Meterade froMeter 25 MeterMeter. dia ‘ G.I. pipe 1.2 Meter. in total length coMeterplete as per specification no. FG-BKT/WB

Supplying & erecting G.I. pipe ‘A’ class 25 MeterMeter dia. erected for enclosing XLPE arMeteroured cable on wall/pole as per specification no. CB-CE

METERaking trench in Hard MeteruruMeter/Tar road having 0.75 Meter depth and MeteriniMeteruMeter 0.3Metertr width as per IS for laying provided cables up to voltage level 1.1Kv cable coMeterplete as per specification No. CW-EXN-CTR

Supplying and laying (including excavation of suitable width & depth up to 90 cMeter) 50 MeterMeter outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth coMeterplete.

Supplying and erecting four pole power contactor 430 V, 16 A for tiMetere switch coMeterplete erected on provided wooden block/ box, with necessary Meteraterials.

Supplying and erecting prograMeterMeterable digital alMeteranac tiMeterer Metericrocontroller based with real tiMetere clock to operate on derived switching “ON” and switching “OFF” street light as per daily sunset and sunrise respectively autoMeteratically having 4 digit LED continuous tiMetere display, relay output 230 V / 10A with 10 hrs. battery backup and Meteranual over drive facility capable to drive different capacity contactors tiMeterer erected in provided METER.S. box.

Supplying and erecting bus bar chaMeterber triple pole with neutral with four aluMeteriniuMeter bars, 500V 300A having 40MeterMeter (Width) X 5 MeterMeter (Thickness), with 99.9 % aluMeteriniuMeter purity as per E91E Grade & Current Density 0.8 A per sq. MeterMeter. coMeterpliance to IS 5082 and enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable nuMeterber of ways and with SMETERC/DMETERC Insulators and accessories of suitable rating coMeterplete as per specification no. CP-BB

Supplying, erecting & terMeterinating FR XLPE insulated, galvanised steel forMetered wire arMeteroured (strip) cable 1100 V, 3½ core 185 sq. MeterMeter. aluMeteriniuMeter conductor coMeterplete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cMeter) 120 MeterMeter outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth coMeterplete.

Supplying and erecting Meterains with 2x6 sq.MeterMeter FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-METERA/BW (lead Wire)

Supplying, erecting & Meterarking DPMETERCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB (METEReter + st light)

Supplying, erecting & Meterarking DPMETERCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/METERCB (EV charger Metereter)

Supplying & erecting CRCA sheet Meteretal one way enclosures of 1.2MeterMeter thickness suitable for DP METERCB /TP METERCB/FP METERCB/RCCB/RCBO coMeterplete erected on angle iron/GI fraMetere.

Supplying and erecting switch disconnector fuse (SDF) switch 415V, 300-320A, open execution, four pole and neutral link AC23 A rated with terMeterinal shrouds on both sides and phase barriers along with telescopic shaft for depth adjustMeterents and door interlock and padlock coMeterplying to IS/IEC 60947-3 Part-1/3 HRC - DIN type fuse, insulation voltage 1000 V for enclosing in panel with rotary handle for ON / OFF operation (without HRC fuse).

Supplying & erecting HRC fuse cartridge 415V, 300A

Providing & erecting prewired Metereter Meterodule suitable for METERCCB panel board with CTs and eMeterfs VIF Metereter.

Providing & erecting floor/wall Meterounting, METERCCB panel board, with door, suitable for four pole incoMetering 250A, 4 ways four pole outgoing, up to 100 A METERCCBs on iron fraMetere, as per specification no SW-SWR/METERCCBPB. (Excluding METERCCBs)

Providing & erecting 4 Pole METERCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable therMeteral (overload) setting and fixed Meteragnetic setting with provided leads, provision for installation of shunt/UV/trip alarMeter contact. METERCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/METERCCB

Providing & erecting 4 Pole METERCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable therMeteral (overload) setting and adjustable Meteragnetic setting with provided leads, provision for installation of shunt/UV/trip alarMeter contact and METERCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/METERCCB

Providing & erecting incoMetering and outgoing cable alleys suitable for METERCCB panel board with door, 250A incoMetering and 4 way outgoing or 400A incoMetering and 2 way outgoing Meterade froMeter CRCA sheet 1.6 MeterMeter thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB.

Supplying and erecting plywood 12 MeterMeter thick fixed to wall or on provided panel board with necessary Meteraterials such as screws, wall fasteners supports, nuts bolts etc. coMeterplete. (Panel +Inveter Batt)

Supplying and erecting PVC slotted box trunking of size 45x30 MeterMeter. with accessories on wall/ceiling as per specification No: WG-METERA/SLBOX.

Supplying, installing, testing & coMeterMeterissioning 3 phase, 22/0.433 kV, 50 Hz., 200 kVA, METERineral oil iMeterMeterersed and naturally cooled outdoor type, Copper wound Non-sealed transforMeterer delta/star connected with additional neutral brought out on load side, teMeterperature rise should not exceed 40℃ by therMeteroMetereter in oil and 45℃ by the resistance Meterethod in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +2.5 to -5 in steps of 2.5%, having 4 nuMeterber of tap positions, with standard accessories coMeterplete with test certificate with losses below 819 Watts at 50% load, 2415 Watts at 100% load as per IS:1180 (part 1) : 2014 with necessary perMeterissions of Electrical Inspector, as per specification no SS- TR-NSL.

Supplying and erecting rolled steel joist (girder) pole 100 x 116 MeterMeter (23 kg/Meter) with base plate in provided foundation as per specification no. OH-PL/RSJ(11MetertrX(2)Nos=22METERtr)

Supplying & erecting 100 x 50 x 6 MeterMeter with 4.7 MeterMeter thick web and 7.5 MeterMeter thick flange channel iron cross arMeter of suitable length for 2.4 Meter wide DP structure and erecting on DP with 50x6MeterMeter claMeterp coMeterplete as per specification no. OH-PL/BKT

Supplying and erecting iron work, sheet Meteretal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, METERS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding coMeterplete erected at the position with necessary Meteraterials duly painted with one coat of red oxide and two coats of enaMeterel paint to Meteratch the switchgears or as per directions by the authority.1) DB Box Support-Equal angle size.50x50x5Meter wt/Metertr Length (2.4Meterx2)+(3Meterx2)=10.8Meter wt=10.8Metertrx3.8 =41.04 kg 2)for DP structure 75x40x4.4MeterMeter wt/Metertr=6.8kg/Meter Length =2.4Meter x5Nos=12Meter Total weight=12 Metertrx6.8 kg =81.6 kg.Total Wt= 41.04+81.6=122.64Kg + 16 kg for panel = 138.64)

Supplying and erecting porcelain pin type insulator suitable for 22kV line with GI pin, coMeterplete as per specification no. OH-INS/PN

Supplying and erecting GI sheet 1.25 MeterMeter (18 SWG) having zinc coating of 350 Metericrons with galvanization process coMeterpliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enaMeterel paint.1)for Distribution box.size 1.2 x 1x0.4Meter. Total size=(1.2x1)x2+(1.2x0.4)x2+(1x0.45)x2= 4.16 sqMeter 2) For DTC METEReter size of Box.1Meterx 0.3x0.4Meter Total size=(1x0.3)x2+(0.3x0.4)x2(1x0.4)x2=1.64 sqMeter. Total=4.16+1.64=5.8 sqMeter.

Supplying and erecting distribution class, 22 kV thyrite type lightening arrester with nut bolts, on provided METERS channel as per specification no. OH-INS/LA

Supplying and erecting G.I. stay set for poles, including loop insulators at inaccessible height with anchor plate 300x300x6 MeterMeter., straining screws, G.l. stay wire 7/8 SWG, G.l. stay rod 20MeterMeterx1.8Meter length and pole claMeterps duly erected in provided ceMeterent concrete foundation coMeterplete.

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cMeter with funnel with a wire Meteresh for watering and brick Meterasonry block C.l. cover coMeterplete with all Meteraterials, testing & recording the results as per specification no. EA-EP(1 LA, 2 Tr Body,1 DB box, 1 Meterccb panel)

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI claMeterps fixed on wall painted with bituMeterinous paint with joints required. As per specification no EA-EP. (25*3 MeterMeter, 0.529 kg/Meter * (15+10+5+5+5+ 15 (Panel))=29.1)

Providing earthing with copper earth plate size 30 x 30 x 0.315 cMeter coMeterplete with all Meteraterials, testing & recording the results as per specification no. EA-EP (2 Tr. Neutral)

Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper claMeterps fixed on wall painted with bituMeterinous paint with joints required. As per specification no. EA-EP.(25*3 MeterMeter, 0.67 kg/Metertr * (5+5)= 6.7kg)

Providing pipe type earthing with 40MeterMeter. dia. G.I. pipe or 20 MeterMeter dia. G.I. Rod coMeterplete with all Meteraterials testing and recording the results as per specification no. EA-EP (2 RSJ Pole + 16 st lt pole)

Supplying and erecting, 22 kV outdoor type drop out fuse with insulator coMeterplete with fuse holders, fuse barrel with Meteretal fitting, fuse eleMeterent Meterounted on METER.S. channel with working current of 15A capacity coMeterplete erected on provided cross arMeter.

Supplying and erecting 22 kV outdoor type gang operated air break, triple pole switch 200 A capacity with 3 post pin type insulator per phase, Meterounted in horizontal or vertical position with necessary channels on provided cross arMeter with adequate length of "C" class G.l. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height froMeter ground level with necessary claMeterp.

Supplying heavy duty operating rod, outer dia 25 MeterMeter & inner dia 20 MeterMeter suitable for 22/33 kV with brass couplings etc. for reMeteroving drop out fuses at 6 Meter length, 4 pieces each with rain shade with hand grip including earthling chain 1.5Meter coMeterplete.

Supplying and erecting GI sheet 1.6 MeterMeter (16 SWG) caution board of size 200 x 150 MeterMeter duly painted with red oxide and enaMeterel paint in METERarathi, Hindi and English erected at position for MeterediuMeter voltage (415 Volt) installation with coMeterpliance to IS 2551-1982

Supplying & erecting barbed wire two ply with 12 SWG ply and 12 SWG barb with a gap between two bars of 75 MeterMeter. firMeterly fixed on provided angle supports with necessary Meteraterials coMeterplete. (6.044 Metereters/kg * 1METERTR *2NOS)

METERaking ceMeterent concrete foundation including excavation (60 x 60 x 150) cMeter deep in 1:3:6 ceMeterent concrete, (20 to 25) MeterMeter stone Meteretal with necessary curing and finishing coMeterplete.(for stay).

METERaking ceMeterent concrete foundation including excavation (60 x 60) cMeter x deep 1/6 of pole length in 1:3:6 ceMeterent concrete 20 x 25 MeterMeter stone Meteretal, 45 cMeter x 45 cMeter x 45 cMeter /45 cMeter dia. x 45 cMeter. height plinth duly plastered, with necessary curing and finishing coMeterplete. (for above 9 Meter poles)

Supplying , erecting & terMeterinating XLPE insulated galvanised steel forMetered wire arMeteroured (strip) cable 22 kV(E), 3 x 95 sq. MeterMeter. aluMeteriniuMeter conductor laid in provided trench / pipe as per specification no. CB-HT ( 2 run)

Providing and erecting Heat shrinkable out door terMeterination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x up to 95 sq. MeterMeter. with necessary Meteraterial as per specification no. CB-JT/HT

Supplying & laying (including excavation) half round reinforced ceMeterent concrete pipe of IS 458:2003 NP-2 class of 150 MeterMeter internal diaMetereter in proper line, level and slope including providing and fixing collars in ceMeterent Meterortar 1:2 and curing etc. coMeterplete.

Supplying and erecting triple pole Meterini feeder pillar with 500V, 300A FPMETERCCB as incoMeterer and 3 outgoing circuits with HRC fuse base and cartridge of 100A with aluMeteriniuMeter bus bar erected in 14 SWG CRCA sheet box with supporting angles, self locks, gasket having IP54,IK10 protection and slanting top to be erected on provided foundation as per specification no. SW-SWR/METERFP

Supply, Installation, Testing and CoMeterMeterissioning 7.2 kW AC Electric Vehicle charger (suitable for 4 wheeler) having MeteriniMeteruMeter IK08 & IP54 protection suitable for single phase, 230V AC, 50Hz, incoMetering and 1 nos. output having capacity of output current of 32A at 230V with Type two connector as per IEC 62196-2 , Interlocking arrangeMeterent & MeteriniMeteruMeter 5 Metereter charging cable length, 3.5" TFT screen for huMeteran interface & LED light for status indication and Meteretering for MetereasureMeterent of consuMetered energy having Meteretering accuracy +/-1%, one hour battery backup for server coMeterMeterunication, eMeterergency push stop button, with user interface by Meterobile application/QR Code/RIFD Card/Password Login and having short circuit, over & under voltage, overload, earth leakage ,Over teMeterperature, surge protection and enclosure Meterade of MeteriniMeteruMeter 1.5MeterMeter duly RAL7035 coated METER.S, erected on iron/GI fraMetere on provided ceMeterent concrete foundation coMeterplete with one year on site warranty, confirMetering to IS 17017 Series as per specification

Est. No. RAESD/OW/ 128 /2024-25 (Sub work -2) Sub-Work No -2 Providing Fire alarm system & Fire Fighting System at Central Administrative Building Mahad, Dist-Raigad Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supplying, erecting testing and commissioning optical type smoke detector on suitable back box with necessary connections complete as per specification no. FF-FAS/SD

Supplying, erecting testing and commissioning heat detector with combination "ROR and Fixed Temp." complete as per specification no. FF-FAS/HD

Supplying, erecting, testing and commissioning manual call point (Pill box) with break glass push button and flip abort switch or agent release switch in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying, erecting, testing and commissioning hooters having high (100dB @ 1m) and low (94dB @ 1m) volume setting, group addressing facility allowing multiple sounders to be activated with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, installing, testing and commissioning of 12 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories , 16x2 Character LCD Display, provision for zone wise contact and beep sound alarm, suitable to operate on 120-220 V AC, 0 - 49 Deg C, 93 ± 2 Percentage RH (non- condensing) at 32 ± 2 Deg C complete as per specification no. FF-FAAS/FACP

Supplying, erecting, testing and commissioning 120 W amplifier suitable to operate on 230 Volts A.C. / 12 Volts D.C. supply complete as per specification no. FF-PA/AFR

Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC

Supplying, erecting, testing and commissioning stand mounted/handheld type wired microphone having 2 mV/Pa sensitivity, impedance level limit 300 ohms and 50 - 16000 Hz suitable to operate in -10 deg C to +55 deg C with min. 7 metre shielded cable and 3 Pin Professional XLR Connector, stereo jack complete as per specification no. FF-PA/MIC

Supplying, erecting, testing and commissioning of 2 core shielded cable complete as per specification no. FF-PA/MCC

Supplying, erecting, testing and commissioning of 1.0 sq. mm speaker wire complete.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 25 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 160 mm outside dia, double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Supplying, installing and testing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all accessories of copper materials & recording the results as per specification no. EA-EP

Supplying and erecting annealed bare copper earth conductor of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete.

Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 1600 to 1800 LPM at 70 to 55 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 30kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP

Supplying, installation, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 70 to 50 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP

Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 450 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP

Supplying, installation, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 1600 to 1800 LPM at 70 to 50 m head driven by 45 HP or suitable HP capacity diesel engine at required working speed suitable for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts DC electric starting equipment with battery of required AH capacity with necessary charger suitable to work on 230v, 50Hz AC supply, diesel tank of minimum 150ltr capacity with first filling of diesel up to 100% level with necessary piping with valves up to engine, exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications etc. as required. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with engine assembly and accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/DP

For addition of capacity of main electric motor driven fire pump MFP (1 working) for hydrant system is more than 22kW, add as follows in the basic cost of Item no 13-5-1 towards increased capacity switchgears and motor starters for main & jockey pumps along with necessary accessories for main & jockey fire pumps MFP=(1working), JP = (1working + 1standby, alternate run per start in auto mode)For main electric motor driven fire hydrant system pump of 30kW capacity & relevant capacity jockey pump add Rs….

For addition of fire sprinkler system to basic fire hydrant system control panel(FCP) which includes one main electric motor driven fire pump MFP (1working) having __kW capacity & relevant capacity jockey pumps, add as follows in the basic cost of Item no 13-5-1 towards increased capacity switchgears busbar and additional motor starters for main & jockey pumps along with necessary accessories with software & hardware for main & jockey fire pumps additional Sprinkler system MFP=(1working)@22kW, JP = (1working+1standby, alternate run per start in auto mode) @relevant capacity For main electric motor driven fire sprinkler system pump of 30kW capacity (1Working) & relevant capacity jockey pumps (1working+1standby, alternate run per start in auto mode, add Rs….

For addition of booster pump for fire hydrant/sprinkler, add as follows in the basic cost of item no 13-5-1 towards necessary accessories, indicators etc. with necessary interlocking and updation of control logic, add Rs....... for 5.5/ 7.5 kW centrifugal type booster pump 1no(1working) , add Rs…....

Supplying & erecting Fully Automatic Star/delta starter suitable for 12.5 H.P to 15 H.P. for 3 phase squirrel cage motor totally enclosed with overload and no volt relay complete erected on provided angle iron frame.

Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings complete as per specification no. FF-PP

Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system.

Supplying and erecting 100 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 150 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Supplying and erecting 20 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT

Providing and fixing high-density polyethylene (HDPE) container one piece moulded triple layer water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres. (5000* 2 nos)

Supply installation testing zincaluminite firewater storage tank having capacity 50KL having structure above ground which gives positive suction to fire pumps. The tank shall include all civil workn including site preparation excavation PCC which can load of tank including of 100% water

Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV

Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting 19 mm dia high pressure poly propylene hose pipe complete as per specification no. FF-FFA/HOP

Supplying and erecting gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ

Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC

Supplying and erecting fire brigade header ( Siamese connection )of 150 mm dia, for supplying water in fire tank complete as per specification no. FF-FA/FMC

Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Supplying and erecting brass orifice plate having 6 mm. thickness, 160 mm outer dia with required diameter of inner hole at every double outlet hydrant valve as per specification no. FF-FFA/OP

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve, hose pipe, hose reel and branch pipe (size 1000 x 736 x 736 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supplying, erecting, testing and commissioning vane type water flow detector 75/80 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes.

Supplying, erecting, testing and commissioning of quartzoid bulb sprinkler, 15 mm (½") dia. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR.

Supplying, erecting, testing and commissioning vane type water flow detector 100 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes.

SUPPLYING ANS ERECTING FIRE EXIT & EXTINGUISHER SIGNAGE INDICATING THE FLOOR NUMBER IN WORDS & SYSTEM(FIRE EXTINGUISHER& ACCESSORIES)

Supplying and erecting fire resistant mortar (20 kg) with fire resistance class S90 as per National Electrical Code (NEC) SP30-2011 suitable to seal the openings of all kinds of cables, pipes and cable support system in steel, aluminium and plastic profiles ( except hollow core conductors). The residual openings shall be closed with filler, as per specification no FF-FRM.

Est. No. RAESD/OW/ 128 /2024-25 (Sub work -3) Sub-Work No -3 Providing AC units at Central Administrative Building Mahad, Dist-Raigad Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. APAC/ WAC (OT)

Supplying, installing, testing & commissioning cassette type room Air conditioning unit 4TR to 4.4TR capacity with refrigerant R32/410A 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, minimum dust filter, noise level maximum 50dBA at position as per specification no. APAC/ WAC

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete.

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 22mm complete.

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 32mm complete.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 22 mm for solar water heater/AC system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 32 mm for solar water heater/AC system.

Supplying and erecting HMS PVC conduit FRLS grade 20 mm dia. with PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.(0.5 *2=1, 0.5*2=1, 0.6*2=1.2, For 1 OU= 1+1+1.2=3.2m, for 24 OU= 24*3.2*3kg/m= 230.4kg)

Supplying 16 amp. 3 pin plug Top bakelite type of 230 V. A.C. supply.

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supplying and erecting PVC insulated PVC round sheathed 4 sq.mm (56 no. x 0.30 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Est. No. RAESD/OW/ 128 /2024-25 (Sub work -4) Sub-Work No -4 Providing 82.5kVA Generator, water pump & CCTV system at Central Administrative Building Mahad, Dist-Raigad Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, fixing and commissioning MCB type change over switch 4 pole, 25A with 3 positions (I-O-II) with centre off position as per specification no. SW-SWR / MCBCOS

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying and erecting minimum Three & above star rated submersible pump set suitable for erection on open well of 2.25 KW/3 HP with 415 V 50 c/s. A.C. supply, having delivery head from 27 to 9 m and discharge from 300 to 660 litres. per minute & pipe of Suction 65mm /Delivery 50 mm diameter erected with necessary H type clamps as per specification No. WP-OSP

Supplying and erecting high density polythene pipe ISI mark 50 mm. dia. suitable for pressure of 6 kg. / cm2 connected to jet/submersible pump with required material complete.

Supplying and erecting non return valve 50 mm dia in position made of gun metal complete.

Supplying and erecting 50 mm dia. gun metal sluice valve at position with necessary materials complete.

Supplying & erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.C. Submersible/centrifugal pump set up to 20 HP consisting of Star Delta starter having relay range 13-21 Amp, S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc.

Supplying and erecting minimum Three & above star rated submersible pump set of 2.25 KW/3 HP with 415 V, 50 c/s AC supply suitable for 150 mm dia. borewell suitable for 120 to 390 LPM discharge at 55 to 11 m head & discharge & delivery Pipe of Size-50mm diameter with a necessary H type clamps as per specification No. WP-SMP

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying & erecting FRP box of size 250mm x 200mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 82.5 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 14.0 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 145 Ltr etc. on provided M20 Grade CC Foundation as per specification no. GEN-DG

Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 62.5 kVA up to 82.5 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Providing & erecting 4 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and erecting SS enclosure for MCCB suitable for 125A to 200A MCCB.

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP (body )

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP (neutral)

Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.(25*3 mm, 0.67 kg/mtr *(5+5)=6.7 kg)

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.(25*3mm, 0.59kg/m* (5+5) = 5.9 kg)

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. 1)(50X50X5mm= Wt /Mtr3.8= Total Length28= Mtr, Total Wt=(3.8*28Mt=106.4Kg) 2)(25X25X5mm= Wt /Mtr1.8= Total Length=17 Mtr, Total Wt= 1.8*17 Mtr= 30.6Kg) Total wt=137Kg (For Shed)

Supplying and erecting GI sheet 1.6 mm (16 SWG) having zinc coating of 350 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. (8*3=24Sq.Mtr ) (For Shed)

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose). (4*2.5*0.3=3)

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. with PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting 20mm dia. corrugated flexible polypropylene conduit

Supplying and erecting 5m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Supplying, fixing, and configuring 24 ports, POE switch in provided rack as per specification No. WG-NWC/ENS

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x600x367 mm) as per specification No. WG-NAS/RAK

Supplying, erecting, testing and commissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS, with backup time of 1 hrs. PWM & IGBT based, with 0.8 to unity output pf complete with all protections as per specification no. AP-UPS

Supplying and erecting 12V/42Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete

Supplying & erecting of High definition 2 Megapixel IP IR Bullet Camera with following features : Image Sensor : minimum 1/2.8" Progressive Scan CMOS, Video Resolution : minimum 1920 x 1080 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 30m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 30m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.

Supplying & erecting of High definition 2 Megapixel IP IR Dome Camera with following features Image Sensor : minimum 1/2.8" Progressive Scan CMOS, Video Resolution : minimum 1920 x 1080 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 30m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 30m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation.

Supplying, installing, testing & commissioning of 64/80 Ch Network Video Recorder (NVR), suitable connect Min. 64 IP Cameras, up to 5 Megapixel Resolution, with HDMI 1/VGA 1 and HDMI 2/VGA 2 outputs provided, Atleast one HDMI output of 4K resolution, atleast one VGA output with output up to 1920 × 1080, Support H.265 or higher, H.264, MJPEG, Supports Redundant Dual Power, Incoming Bandwidth 320 Mbps with minimum 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps self-adaptive Ethernet interface, support multi brand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specificationss no. CCTV-NVR

Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR

Supplying & erecting 55" professional LED display with 1920 *1080 ( Full HD) Display, suitable for 32/64 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

Royalty Charges Supply of Rubble, METERuruMeter, Soil, 60MeterMeter./40MeterMeter. Meteretal(Hand broken), royalty charges are not included in the rates.Any revision in Royalty charges and surcharge shall be included in the rate analysis of the respective iteMeter. If there is variation in these rates the difference shall be paid extra over the iteMeters to the contractor and shall be recovered if these rates are reduced by Govt. i.e. Revenue departMeterent. The GovernMeterent of METERaharashtra, Revenue and Forest DepartMeterents Gazette No.146 Dt. 04 June 2021 States that the Royalty charges of Rs. 216.18/cuMeter. are to be considered. The surcharge levied on Royalty shall also be payable to the contractor.

Laboratory testing Charges required for Meteraterial testing on the basis of testing frequency and charges fixed by Vigilance and quality control circle, Pune for the year 2021-22, as per Superinending Engineer, Vigilance and quality control Circle, Pune, Letter No.