SPECIAL REPAIR TO BLDG NO. 07 SOLTAM OF 506 ARMY BASE WORKSHOP UNDER GE (EAST) JABALPUR

Amount

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debrise to out side MD land complete all as specified & directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400Sqm and depth exc 50mm but not exc 100mm by using mechanical scarifier including racking over and grading the broken-up surfaces to the proper camber or removing to a distance not exc 50M from the starting point and stacking complete all as directed.

Hard core of stone (granite/ basalt/ trap) boulders or broken stone of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement forming joints 10 mm wide to full depth at every 3M intervals and at every change of direction and filing with bitumen sand mixture 1:3 by weight complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base / mass concrete finished even and smooth without using extra cement complete all as specified and directed.

M&L for 80 mm thick rubber mould reflective surface PU coated, factory made, coloured, pre-cast PCC interlocking paver blocks/ tiles conforming to IS 15658-2006, M-40 designation of section as approved by GE in hard standing, laid dry over & including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L for providing and laying at or near ground level factory made Pre cast kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & directed.

Dismantling brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

S&F steel rolling shutters, gear operated type with gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple, Safety lever locks mild steel with 4 levers and one shop coat of primer, erected in position as indicated for 1.25 mm thickness of lath complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in bed block for hold fast, plinth courses, copings, bed plates etc and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L rendering 15mm thick in cement plaster 1:6 on surfaces fair faces of brick work and surface finished even and fair without using extra cement all as specified and directed.

Dismantling structural steel work including doors, gates, ladder and framed work of watch tower etc complete all as specified and directed.

Dismantling of AC (corrugated or semi corrugated etc.) sheets including ridges in roof coverings complete all as specified & directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering and ridge complete all as specified and as directed.

M&L for mild steel work conforming to Fe-290 Gde -165 as in hand rail, half round or other steel section or core for wooden hand rail strait portion, drilled and countersunk for balusters running bars for doors, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

Supply and fix rolled mild steel sections conforming to Fe- 410-W (Gde E-250) quality-A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates etc complete all as specified & directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified & directed.

M&L for mild steel work of sections conforming to Fe.290.Gde-E-165 as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings exclusive of steel sheeting, running rails & guides and hanging, fastening & fixing complete all as specified & directed.

M&L 1.6 mm thick mild steel, plain, black sheet in hearth, covering to door shutters, chowkhat(frames), chullah hoods, water tanks, water troughs, ducts, urinal troughs and funnels etc., cut to size, edges beaded if directed, holes punched including round headed screw, clout nails or rivets and fixed to wood or steel members etc with plain 40 mm lap joint or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets etc. as required complete all as specified and directed.

M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W Gde- E-250 quality-A complete all as specified and directed.

S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed. Note : 1. The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. 2. Truss design shall be got done by the contractor from Government Engineering College/NIT/IIT and submit the same to GE, duly vetted by Government Engineering College/NIT/IIT. Expenses incurred thereto in designing and vetting of truss is deemed to be included in the unit rate quoted by the Contractor against this item.

Supply and fix pre-painted galvalume aluminium zinc coating GI based 0.50mm thick (AZ-150) corrugated steel sheet of any colour having minimum tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts as complete all as specified & directed.

S&F plain, galvanised , mild steel sheeting with grade of zinc coating 275, 1.00 mm thick, of any colour, as in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) complete all as specified & directed. ( Note : The height of building where the work will be carried out, is upto 18.00 metre )

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed with tinned tacks or wire staples complete all as specified and as directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of aluminium paint of colour as approved by GE over and including a coat of aluminium paint red-oxide zinc chrome primer complete all as specified & directed.

M&L for preparation of new surfaces of iron/ steel of any description not exceeding 10 cm width or girth and applying two coat of aluminium paint of colour as approved by GE over and including a coat of aluminium paint red-oxide zinc chrome primer complete all as specified & directed.

M&L for preparation of old painted surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of aluminium paint of colour as approved by GE over and including a coat of aluminium paint red-oxide zinc chrome primer complete all as specified & directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M&L for prepration of new plastered surfaces of walls and applying two coats of cement base paint over & including a coat of cement primer complete all as specified & directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description and applying two coats of cement base paint complete all as specified & directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified & directed.

M&L for suspended false ceiling system using chicago metallic (E-grid) exposed suspended system, grid size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length), Cross Tee of dimensions 29mm X24mmX0.8mm thick ( thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of Tee 0.195 kg for 600 mm length) and wall angle of dimension 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length) with and including 6mm thick HPSC(High Pressure Steam Cured) pre-primed , self embossed, textured designer board, water, termite and fire resistant for insulation and acoustic purpose to be placed in the grid system, duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip), hold down clips (Wt-0.0035 Kg/clip) with provision of light fixture complete all as specified and directed.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc including removal of debrise to out side MD land complete all as specified & directed.

M&L for PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in filling undulation of roof , chajjas/beam etc including necessary form work if required complete all as specified and directed.

M&L for 10mm thick rendering over roof surfaces in CM 1:4 with using water proofing compound @ 2% by wt of cement or as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum over lap of 100mm and over lap shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer's as specified for polymeric water proofing membrane.

Taking down loose plaster over rusted reinforcement and then cleaning rusted reinforcement and exposed concrete surface by sandblasting using mechanical devices or any other established methods and treating the reinforcement in following stages complete:- (a) Application of two coats of mineral based polymer modified corrosion inhibiting primer colusal MK + Colusal 25. (b) Application of two component polymer based bond coat Zentrifix HB + Nafufill BB2 or mortar low permeability or guniting with guniting aid . (c) Application of carbonation resistant polymer modified ready to use fine mortar, nafuquick+nafufill BB2 or Zen-trifix F82 + Nafufill BB2 over the whole surface. (Note : The above application shall be carried out by the authorised Applicator of M/s MC-Bauchemie (India) Pvt Ltd or any other Manufacturer as approved by GE.)

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debrise to out side MD land complete all as specified & directed.

M&L for heavy duty vitrified tiles, Durastone floor tiles of Somany/Sandex series of Endura Johnson/ Equivalent tiles as approved by GE, size 600 x 600 x 10 mm thick, jointed and pointed with neat cement slurry as in floors including 15 mm thick screed bed in Cement Mortar (1:6) complete all as specified & directed.

M&L for glazed ceramic coloured tiles 350x250x7mm or 450x300x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for non-skid coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

Supply only liquid water proofing compound, ISI Marked, complete all as specified and as directed..

M&L for 15mm thick rendering in two layers, first layer 10mm thick in CM 1:6 and other finishing layer 5mm thick in CM 1:4 with and including water proofing compound @ 2% by wt of cement or as per manufacturer's instructions on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall and apply two coats of oil emulsion distemper over 2mm thick of Birla/ JK wall care putty over a coat of cement primer for smooth finish of wall complete all as specified and directed.

M&L bands, straps, supports or stays for rainwater (stack clamp), ventilating pipes, including bolts, if required, hooks (stays), heavy for large gates, hooks and pintle hinges, large hasps and staples, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts two way and three ways straps, plate washers and similar articles conforming to Fe-290(Gde-E-165) complete all as specified and directed.

M&L for PCC( 1:2:4) type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.50M clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates , kerb etc and the like including weathering, slightly rounded/ chamfered angles and throating, complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete all as specified and directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Supply & fix factory made solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in frame complete all as specified & directed.

M&L for 19 mm thick high density PVC solid fibre board, duly laminated, 2 mm thick prelaminated PVC sheet on front face(ISI marked), in any position, on cupboard complete all as specified & directed.

Supplying & fixing hasp and staple of size 100mm , safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

Supplying & fixing 100mm size butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized, type C-22 complete all as specified & directed.

M&L for IInd class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

M&L for cutting chases in brick wall, pinning in and making good in cement mortar (1:3) to match with existing surface for Cutting exc 10 cm but not exc 20cm girth complete all as specified and as directed.

Supply and fix 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply & fix 300mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Supply and fix aluminium handles 150 mm size, cast type, anodised complete all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat synthetic enamel paint of colour as approved by GE over and including a coat of pink primer complete all as specified & directed.

Supply and fix factory made steel window flush welded with side hung shutters including box type hinges with steel handle, steel peg stay 250mm long with suitable lugs and with glazing bars dovetailed or welded complete all as specified & directed.

Supply and fix factory made steel window flush welded with side hung shutters including box type hinges with steel handle, steel peg stay 250mm long with suitable lugs but without glazing bars complete all as specified & directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed with tinned tacks or wire staples complete all as specified and as directed.

S&F sheet glass, ordinary quality 3.0mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ metal frames fixed with beads or glazed with putty complete all as specified & directed.

S&F figured glass, pin head type 4.0mm thick and glazing with and including rubber gasket neoprene pad and aluminium cleat as in aluminium shutter, in squares n. exc 0.5sqm in each pane complete all as specified & directed. ( Note : Aluminium cleat shall be measured and paid for separately alongwith aluminium shutter )

S&F 6.4 mm thick rough cast wired glass fixed with MS flat and screw, in square n. exc 0.5 sqm in each pane complete all as specified and as directed. (Note :- MS flat shall be measured and paid for separately under relevant item of this BoQ)

Fixing only 6.4 mm thick rough cast wired glass and MS flat , in square, n. exc 0.5 sqm in each pane except rough cast wired glass complete all as specified and as directed. (Note :- MS flat shall be measured and paid for separately under relevant item of this BoQ)

Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia 150mm, set in cement mortar complete all as specified and directed.

M&L concrete bed to pipes in PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for 300 mm bore sewer pipe line complete all as specified and directed.

M&L Reinforced cement concrete pipes 300 mm bore class NP-2 laid and jointed, with collars complete all as specified and directed.

Supplying & fixing 150mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including fitting, necessary clamps of requird size etc complete all as specifed & directed.

Supply & fixed in repairs, 150mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply & fixed in repairs, 110mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply & fixed in repairs, 75mm bore PVC (SWR) bends of any radius complete all as specified & directed.

Supply & fixed in repairs, PVC (SWR) junction single (single T), equal or unequal, 110mm bore complete all as specified & directed.

Supply & fixed in repairs, 110mm bore PVC (SWR) vent cowl complete all as specified & directed.

Supply & fix in repairs vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed.

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but plastic water closet seat, black/ white, closed pattern with recessed bottom, and including seat cover and mild steel chromium plated or aluminium hinging device, complete all as specified & directed.

Supply & fix in repairs vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F in repairs, 15mm dia bib cock,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed.

S&F in repairs 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed.

Supply and fix in repairs, pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm dia complete complete all as specified & directed.

Supply and fix in repairs, 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 20mm bore of pipe complete all as specified and as directed.

Supply & fix 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & fix 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Refixing old steel water tubing 15mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Refixing old steel water tubing 20mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Dismantling of water tank of any description of capacity exc. 250 litres but not exc. 500 litres, removing to store or from the site complete all as specified and as directed.

Dismantling of water tank of any description of capacity exc. 500 litres but not exc. 1000 litres, removing to store or from the site complete all as specified and as directed.

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Supply & fix, 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed. (Note-Min weight should not be less than 210 gms)

Supply & fix in repairs kitchen sink with drainage board made of stainless steel 1.0mm thick with plug, washers with and including 32 mm dia PVC rigid waste pipes and C.P coupling including fixing cantilever brackets of suitable shape & size as required at site and connecting unions to pipe, overall size 915 mm x 460mm, bowl size 410 mm x 330 mm x 160mm and necessary cutting to slab complete all as specified & directed.

Taking down steel sliding door shutter, area exc. 10 sqm but n.exc. 15 sqm , repairing and overhauling of sliding shutters and greasing/oiling of members of shutters and fixed in old position with and including change of mild steel pulley of dia n.exc 150mm , 02 nos in each panel and change of brass supporter/guides in bottom, 02 nos in each panel with and including preparation of old painted iron and steel surfaces by scrapping & rubbing down with sand paper, removing dents and scratches, if any, and filling the same with paste filler and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Taking down of old steel door gate of any description and repair the wheels, rails etc of door and overhauling, refixing the same in position complete all as specified and as directed. Note:- Area of Each steel door not exceeding 50 Sqm.

M&L for anodized aluminium door with frame side hung type in single or double leaf of 2mm thick aluminium sections including 5.00mm thick tinted glass fixed with & including anodized aluminium snap beading, glazing clips, joining clips, screws, standard rubber gasket and disc type handles two nos. for each shutter, aluminium anodized tower bolts 200mm long two nos. for each shutter and one no godrej pattern mortice lock device complete with double keys for each door, one hydraulic door closer aluminium (die cast) body designation No. 3, universal type, made up of minimum 1.25 mm thick aluminium alloy sheet foundation box for each shutter complete all as specified and directed with following specifications :- (a) Aluminium section for door frame =101.50x44.45x2mm (b) Aluminium section for styles and top rails of shutter = 83.5 x 44.45x2mm (c) Aluminium section for middle and bottom rails of shutter = 114.50 x 44.45x2mm (d) Aluminium door frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed. (i) Make of aluminium sections :- M/S JINDAL or M/S HINDALCO or M/S INDAL as approved by GE. (ii) Make of floor spring :- Kelwyn or Amar as approved by GE. Note:- Aluminium door frame, as the door is side hung and 5 mm thick tinted glass will be measured and paid separately.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/metre including necessary jointing cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed. Make of aluminium sections:- M/S JINDAL or M/S HINDALCO or M/S INDAL as approved by GE. (Note:- Glazing shall be measured and paid for separately. )

Supply & fix 5 mm thick tinted glass ordinary quality glazing with and including necessary rubber gasket and aluminium beads with cleats as in aluminium door/ window shutters complete all as specified and directed.

S&F in repair 18 mm thick PVC sheet one side prelaminated of approved texture as in cucupboard including necessary fitting & fixture as per manufacturer instructions complete all as specified and directed.

S&F aluminium grill stain finish fix to window with F channel Complete all as specified and as directed. Make :- Deco Grill Cat No. DG 102, DG-103, DG 104 & DG - 117.

Supply and fix 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply & fix 250mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

S&F in Door closer hydraulically regulated aluminium (die cast) body , designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

Supplying & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified & directed.

M&L for forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed. ( Joint will be made in concrete after setting of flooring and cutting the joint by diamond cutter or suitable mechanical cutter )

M&L for forming construction joints 30 mm deep x 10 mm wide filled with sealing compound grade 'A' complete all as specified and directed. ( Joint will be made in concrete after setting of flooring and cutting the joint by diamond cutter or suitable mechanical cutter )

M&L forming expansion joints 12 mm thick, filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing with sealing compound grade 'A' complete all as specified and directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one light/fan point complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including stove enamelled steel conduit conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one light/fan point complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including stove enamelled steel conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 5 pin, 5/6 Amps controlled by one no. one way 5/6 Amp piano type switch on the independent board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 2.5 sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 2.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including stove enamelled steel conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the switch socket combination of 5 pin 15 Amp on independent board complete all as specified & directed.

M&L for point wiring concealed type with 4.00 sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 4.00 sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the switch socket combination of 5 pin 15 Amp on independent board complete all as specified & directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 2.5 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 2.5 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 2.5 sqmm cable & one run of 2.5 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4.0sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 2.5 sqmm drawn in and including rigid steel conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 2.5 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 2.5 sqmm cable & one run of 2.5 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid steel conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4.0sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

Supply & fix switch piano, flush type single pole, one way 5/6 Amps, 240 volts complete all as specified & directed.

Supply & fix socket outlet 2 in 1, 2 pin 5/6 Amps and 3 pin 5/6 Amps, flush universal type complete all as specified & directed.

Supply & fix switch socket combination 2 in 1, 3 pins 5/6 Amps and 3 pins 15/16 Amps flush universal type controlled by one switch complete all as specified & directed.

Supply & fix switch socket combination 2 in 1, 3 pins 15/16 Amps flush universal type controlled by one switch complete all as specified & directed.

Supply & fix in repairs, rotory stepped type electronic fan regulator mini flush type 120/ 280 Volts complete all as specified & directed.

Supply & fix ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply and fix in repairs, angle type lamp holder insulated with polycarbonate body and back plate housed with porcelain base suitable for 8Watt LED with and including 8Watt retrofit type LED complete all as specified and directed.

Supply and fix in repairs, Decorative ultra slim square profile LED lighting fixture of 10 watt with extruded polycarbonate, environmental friendly, energy efficient and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply and fix in repairs, Decorative ultra slim square profile LED lighting fixture of 18 watt with extruded polycarbonate, environmental friendly, energy efficient and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

S&F 36 watt LED luminaire precisely designed decorative PMMA diffuser 2x2 panel light that unites a creative design with state-ofthe-art LED technology. The concept of protruded decorative diffusers achieves a great sense of novelty and flexibility with multiple diffuser designs while offering perfect illumination and greater uniformity. This design stands out stunningly among the boring old modular ceiling patterns including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply and fix in repairs, 100 watt Next generation, energy saving, environment friendly & robust highbay LED with PDC housing suitable for ceiling (Surface/Suspended) mounting with system efficacy upto 150 lm/W & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply and fix in repairs, 45 watt new generation energy saving and environmental friendly long life LED security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP65 protection and impact resistance of IK07 on bldg wall with and including pipe bracket made out of G.I tubing 32/40 mm dia bore medium grade ISI marked 1.20m long bent to shape & providing clamps 2 Nos made out of 50 x 6mm Flat iron/ MS clamps & 12mm dia bolts, nuts & washers etcand two coat painting of approved colour on brackets completely with and including synthetic enamel paint and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Taking down of existing exhaust/ ceiling fan of any size/ sweep for keeping the safe cosdoy and re-fixing/ re-hanging the same after repair work or as directed and connecting up the same with & including twin twisted copper flexible wire from ceiling rose to exhaust/ ceiling fan complete all as specified & directed.

Supply and fix Distribution Board of MCCB made out of CRCA sheet, powder load line coated, vertical type, double door, 4 way including taking down old unserviceable any type MCCB DB, after cutting chases and making good the surface by necessary patch work and surface finish including making connections complete all as specified and directed.

Supply & fix in replacement, single pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB SP of capacity 20 Amps 240 volts complete all as specified & directed.

Supply & fix in replacement, double pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB DP of capacity 20 Amps 240 volts complete all as specified & directed.

Supply & fix in replacement, teipple pole and neutral sheet metal enclosure (AC box) with a three pin & earth plug and socket with one no. MCB TP of capacity 63 Amps 415 volts complete all as specified & directed.

Supply and fix SPN DB 8 way sheet metal enclosure, IP 43-IK 09 with metal door, 240/ 415 volts with copper bus bar of 100A and neutral bar, earth bar and cable ties for cable management all enclosed on standard steel sheet flush or surface mouting type factory fabricated complete all as specified and directed.

Supply & fix MCB SPN, 40 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix MCB SP, 6 to 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

S&F MCCB 4 pole, 415 V ,with thermal megnetic release, adjustable type 100 Amp with breaking capacity 16 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

S&F MCCB 4 pole, 415 V ,with thermal megnetic release, adjustable type 160 Amp with breaking capacity 36 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

S&F MCCB 4 pole, 415 V ,with thermal megnetic release, adjustable type 200 Amp with breaking capacity 36 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

S&F MCCB 4 pole, 415 V ,with thermal megnetic release, adjustable type 250 Amp with breaking capacity 36 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

S&F MCCB 4 pole, 415 V ,with thermal megnetic release, adjustable type 400 Amp with breaking capacity 36 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 50 sqmm, 3.5 core including jointing materials such as cable glands & lugs etc after taking out the old unserviceable cable and testing on completion complete all as directed.

S&F single pointed air termination aluminium rod. 12 mm dia, 300 mm long with necessary fixing arrangements as per site requirements complete all as specified and directed.

S&F aluminium strip 25 mm x 3.15 mm complete with saddles and fixing screws as roof conductor complete all as specified and as directed.

S&F GI strip 32 mm x 6 mm buried in ground complete all as specified and as directed.

M&L Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. , 8mm dia. , 25 mm long hex. head screw complete all as specified and as directed.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to GI earth strip of size 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Schedule of credit amount of Rs 3,93,968.00 to be deducted during AOC

Tiki Water proofing Co