Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹28.9 LAccepted-AOC | L1 | Accepted-AOC Accepted being lowest quoting | |
| 2 | L2₹31.8 L+₹2.3 L (7.96%)Rejected-AOC 1542 URBAN ESTATE II HISAR 125 005 HARYANA | HISAR | HARYANA | 125005 | L2 | Rejected-AOC Rejected being higher quoting | |
| 3 | L3₹33.1 L+₹3.6 L (12.4%)Rejected-AOC | L3 | Rejected-AOC Rejected being higher quoting | |
| 4 | L4₹34.1 L+₹4.6 L (15.7%)Rejected-AOC H NO 920 SEC 16 17 HISAR HARYANA 125005 | HISAR | HISAR | HARYANA | 125005 | L4 | Rejected-AOC Rejected being higher quoting |
Tender Value
₹35 L
EMD Value
₹70,000
Closing Date
22 Sept 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Hisar
Garrison Engineer Hisar Military Station Hisar 125006
CA No GE(H)-17/2022-23 REPAIR / REPLACEMENT TO FLOOR / WALL FINISHES AND ALLIED WORKS OF OTM ACCN ZONE C IN THE AOR OF AGE B/R I UNDER GE HISAR AT HISAR MIL STN
2022_MES_535952_2
CA No GE(H)-17/2022-23
Open Tender
Civil Works
Item Rate
240 days
Hisar Mil Stn
As per Tender documents
6 documents required · 6 mandatory
₹500
GE Hisar
₹70,000
Yes
11 Oct 2022
1 Sept 2022
24 Sept 2022
1 Sept 2022
22 Sept 2022
9 Sept 2022
Amount
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.
Demolition of stone slab and tiles of any description or thickness in floors, apron etc laid bedded and pointed in any mortor etc complete all as specified and directed.
Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets complete all as specified
Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.
Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.
Taking down shutters of any description, exc 1sq.m and n.exc 2 sq.m each and removal from site etc complete all as specified and directed.
Taking down chowkat or frame with shutters area not exc 1.5 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.
Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good complete all as specified.
M&L for PCC 1:3:6 type C1, using 20mm graded crushed stone aggregate as in filling up chowkat hollows and similar works as directed, complete, all as specified.
M&L precast cement concrete (1:2:4 type B0 using 12.5mm graded stone aggregate) louvers and jallies, 25mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 all as specified & as directed.
M&L for precast cement concrete (1:2:4 type B1, using 20mm graded crushed stone aggregate) as in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match, set in CM 1:6 all as specified & as directed.
M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.
All as per serial item No 12.00 here-in-before but except bricks. Note : Old serviceable bricks retrieved from serial item No. 4.00 here-in-before shall be used under this item.
M&L brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.
S & F factory made 30mm thick flush shutter, solid core construction, with block board core and both sides cladding of 2mm thick Plain colour PVC sheet fixed or laid on to flush doors by using rubber based adhesive, supplying & fixing all as specified and directed.
S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.
S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications etc complete all as specified and directed.
S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour sheets for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.
S&F butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.
S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.
S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified.
S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.
S&F 150mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed.
S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.
S&F in repairs 25mm bore & 1.00mm wall thickness stainless steel fancy type decorative curtain rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed.
S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.
S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.
S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.
S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) including shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including powder coated 'D' type handle of suitable size, tower bolt of suitable size, suitable size hinges heavy grade complete all as specified & as directed. Note :- Mortice lock, Door closer & Glass panes/wire cloth shall be measured & paid seperately under relevant item of BoQ.
S&F anodized aluminium grill thickness of wave wire 6.25mm dia and gauge size 60x70mm gapping of required design and shape, fixed in aluminium window with and including cutting, screwing, aluminium beading / cleats complete all as specified & as directed.
S&F Door closer aluminium (extruded section body), hydraulically regulated, designation No. 1 universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.
S&F mortice lock brass 4 lever vertical type size 75mm and fix in aluminium door shutter etc complete all as specified and as directed.
S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.
S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.
S&F 5mm thick hollow PVC wall lining, single side prelaminated with flat or fancy patterned on laminated side, PVC sheet inclusive of fixing with screws or with solvent cement required at site on walls including necessary corner angles, filltes, locking system etc required at site complete all as specified and directed.
S&F Anodised aluminium snap grid size 605 x 605mm frame work for false ceiling including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long with & including 4mm thick HPSC pre-primer non asbestos fibre cement building board (E-Classic) with decorative finish, factory made, 600mm x 600mm in size and complete all as specified & as directed
M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in levelling course 25mm thick finished fair & even complete all as specified & as directed.
M&L for premium polished glazed vitrified body tiles (PGVT), 10mm thick of size 800mm x 800mm, coloured (light shade as approved), as in floors laid with 3mm spacer and pointed with two component exposy resin based tintable grout to match the shade of tiles, set and jointed in neat cement slurry laid over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed. Note :- Contractor should get material as per latest catalogue of approved make.
M&L for premium glazed vitrified body tiles (GVT), 10mm thick of size 1200mm x 600mm, of any coloured / pattern, matt finish, as in floors laid with 3mm spacer and pointed with two component exposy resin based tintable grout to match the shade of tiles, set and jointed in neat cement slurry laid over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed. Note :- Contractor should get material as per latest catalogue of approved make.
M&L for non skid premium vitrified body tiles, 7 to 8mm thick, light shade polished shade of size 400mm x 400mm, as in floors laid with 3mm spacer and pointed with two component exposy resin based tintable grout to match the shade of tiles, set and jointed in neat cement slurry laid over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed. Note :- Contractor should get material as per latest catalogue of approved make.
M&L for vitrified heavy duty paving tiles (Exterior), 12 to 15mm thick (Delta Ivory / Delta Terracota), Matt finished, size 300mm x 300mm, as in floors laid with 3mm spacer and pointed with two component exposy resin based tintable grout to match the shade of tiles, set and jointed in neat cement slurry laid over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed. Note :- Contractor should get material as per latest catalogue of approved make.
M&L for premium glossy ceramic coloured tiles 7mm thick & of size 300mm x 600mm, polished shade, as as on vertical surfaces such as dado, skirting etc. laid with 3mm spacer and pointed with two component exposy resin based tintable grout to match the shade of tiles, set and jointed in neat cement slurry laid over & including 10mm thick rendering in cement & sand mortar 1:4, complete all as specified & as directed. Note :- Contractor should get material as per latest catalogue of approved make.
M&L for premium glossy ceramic coloured tiles 7mm thick & of size 400mm x 800mm, polished shade, as as on vertical surfaces such as dado, skirting etc. laid with 3mm spacer and pointed with two component exposy resin based tintable grout to match the shade of tiles, set and jointed in neat cement slurry laid over & including 10mm thick rendering in cement & sand mortar 1:4, complete all as specified & as directed. Note :- Contractor should get material as per latest catalogue of approved make.
M&L for 20mm thick granite (of any type) work table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc laid over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.
M&L for 12mm thick wall lining of Granite tiling of approved shade/design, set over & including 15mm thick cement mortar backing in CM (1:4) and pointing with white cement (1:2) with pigment to match with shade of granite tile complete all as specified and as directed.
M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.
M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.
M&L for factory made chequered cement concrete tiles, vibrate type, designer type, glossy finish, 40cm x 40cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, over & including 20mm thick screed bed in cement & sand mortar 1:6, complete, all as specified & as directed.
M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified. Note : - Kota stone shall be of size 550mm x 550mm (minimum) when brought at site.
M&L for machine cut Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar, laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.
M&L for Continuous brick edging using sub-class 'B' bricks, with width equal to the width of the brick, laid dry on end vertically complete all as specified.
M&L for grinding, rubbing and mirror finish polishing to existing kota stone/mosaic floors/vertical surafces etc complete by mechanically by using different grits all as specified and directed.
M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls over & including 2mm thick wall care putty all as specified & as directed.
M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant primer of same make all as specified & as directed.
S&F in repairs 2.8mm thick acrylic transparent sheet, in square/rectangular not exc 0.5 sqm in each pane fixed / lock with window frame by using PVC snap beading with necessary self tapping reviting / screwing and suitable method with and including hacking out old broken glass (any thickness, size, quality or description) from any type of window / door glazed with putty or fixed with beads complete all as specified and directed.
S&F 5.5mm thick dark coloured sheet glass in glazing to aluminium door, window & partition including pad/gasket all as specified and directed.
M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.
M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified.
M&L for preparation of new steel surfaces (already applied with coat of primer) of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint of approved tint on existing primer complete all as specified.
m/s krishna engineers1
M/S KAVITA CONSTRUCTION
SHRI HARI BUILDERS
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.PDF
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .