Construction of Academic Block of Transit Campus of IIM at Tech City, Bongora, Guwahati including Balance Works of CFC building of Amtron

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead All kinds of soil.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered) : Depth not exceeding 1.5 m

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu?ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Cold twisted bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood: 35 mm thick shutter

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 9.74.1 250x10 mm

Providing and fixing bright finished brass handles with screws etc.complete: 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.1 300x16 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 26.86.1 Frame size 45 x 70 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,complete. Size of Tile : 600 X 600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 600x600

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).- Common Area

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 12.59.1 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

12 mm cement plaster: 1:4 (1 cement : 4 fine sand)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With water thinnable cement primer on wall surface having VOC content less than 50 grams/litr

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour Two coats

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 14.28.2 25 mm diameter.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded polyethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Installation of HIT -V(8.8)-M20 bolt with total anchor length of 250mm with Hilti RE 500 V4 at any height including scaffolding cutting etc. as per direction of engineer incharge.(Payment of bolt to be made separately)

Supplying fitting and fixing Satin finish Grab Bar of approved brand as directed and specified.

Providing and fixing Holding bolts including nuts and washers complete as per direction of engineer Incharge

Providing ,fabrication & fixing of DGU glazing(6mm reflective glass + 12mm air gap & 6mm clear tempered insulated glass of approved shade) made out of anodised aluminum outer frame J-S5013 of wt-0.774kg/m, shutter J-S5019 of wt 1.357kg/m, transom J35983 of wt-1.875 kg/m & sash frame J-35837 wt-0.756kg/m including necessary mullion, weather silicon with backer rod, structural silicon with double side tape, required screw, nut, Bolt, rivets,cleat,EPDM gasket,clamps & approved multiple locking handle system for openable glazing etc. as per approved shop drawing & as per direction of engineer in incharge.

Providing and fixing of FRAMELESS GLASS INTERNAL PARTITIONS at all locations with 12mm clear tempered glass or as per elevation drawings enclosed with approved make of 316 grade patch connector S.S. fittings of DORMA/Ozone or equivalent make , fixed with S.S. screws or with fixing clips including necessary filling up gaps at junction, at top, bottom u channel make jindal and sides with required weather silicon with backer rod shall be inserted between alluminium section channel and glass as well as both inside and outside around the periphery of the glass to make the glazing water tight and air tight as shown in enclosed drawings and directions of Engineer-in-charge. Glasswork including making suitable holes in the glass before tempering process of glass, for installation complete as per design drawings. The periphery shall have to be sealed both from inside and outside with silicon weather sealant to make the glazing water and air tight.The sealing of glass to patch connector hardwares with stainless steel fixtures as detailed in drawings. Silicon sealant grade shall be "Dow corning - USA" or " "WACKER - Germany" or approved equivalent as per the design requirement. The partition shall be aligned for the entire height and for the entire length by laser beam equipment to ensure 100 percent X-axis and Y-axis alignment. The glass joints must be properly sealed with weather silicon to make the joint water tight and air tight as well as per design complete at all levels and as directed.

Supplying and fitting and fixing 12mm toughned spider glass in front canopy & Atrium of Open Sky as per direction of Engineer Incharge.

Supplying, Fixing and Fitting of not less than 75 mm thick partition wall with 08 mm thk Calcium Silicate "Hilux Boards" make fixed over Gyp steel flanged studs fixed vertically on floor and ceiling at interval of 600mm c/c. The 12 mm thick calcium Silicate board of approved brand to be fixed on the both sides with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm) made of GI steel with joints staggerred, to be complete in all levels as per design and as directed by the department.

Preparing the surface by cleaning & chipping the surface for removing loose, laitance etc., cutting all the constructional joints in a “V” groove shape and applying Nitobond SBR latex followed by polymer modified mortar to fill the same. Applying two coats of Nitocote CM210 over the prepared surface. UGR

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Construction of Security Shed of Size 5.08 m x 2.25 m with height of shed 3 m with 0.9 m parapet wall above it and 0.75 m height plinth including all floor fittings, UPVC Window, WPC Frame and Flush Door Shutter including inside internal connections and wiring and including painting inside and outside.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Filling the gap in between aluminium/ stone/ wood frame and adjacentRCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540- F & ISO 11600 21.19.2 Upto 10 mm depth and 10 mm width

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. (a) Continental (Cat.No.ACN-1135N) (with glass bottle) Jaquar Make

Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (ii) Bottle trap (with internal partition) 32mm size with 300mm long wall connection pipe (Cat.No. ALD-769B) Jaquar Make

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc.complete at all levels including below G.L. as directed and specified. i)50 mm dia (Medium) Using Tata make Exposed on Walls

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (ii)15mm dia( Angular stop cock ) Jaquar Make Continental/ Clarion

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed.

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) i) Sink cock with swinging casted spout

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. a) 50mm dia

b) 40 mm dia.

c) 25 mm dia.

d) 2O mm dia.

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed A) G.I. pipe with GI fittings-TATA / SAIL/ITC /NEZONE /Bansal/Jindal (Medium) i) 15mm diameter

ii)20mm diameter

iii) 25mm diameter

vi) 50mm diameter

viii) 80mm diameter

ix) 100mm diameter

Supplying fitting and fixing check valve (non return valve) including thread to pipes. vi) 80mm diameter

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of DOLPHIN make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (A) With Zoloto fittings (III) 5000 liters capacity (a) 4 mm thick Vessel

Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of TARUS make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs (B) Chemical Dosing system- Electronic dosing units provide sustained chemical dosing (Chlorine, Alum. Soda Ash) in water either in tank or to pipelines. We also have non-electric dozers of FRP or Ms body wherever required Complete set with Pentair make, PVDF, Material, Ceramic balls, suction tube, strainers, nrv, 100 litres tank.

(E) Water SOFTNER Converts hard water to soft water using cation resins, brine regeneration. Complete set with FRP vessels, Multiport valves, pipe & fittings. Tank capacity upto- (II) 5000 liters capacity

Loading , unloading , placing to place, installation , fixing , testing commissioning of Health faucet with 1 m long C.P. brass flexible pipe of approved quality :

Fitting and fixing approved brand CP on brass connector flexible with both ends coupling with heavy brass over C.P. nut 15 mm dia.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 Rectangular shape 1500x450 mm

Providing and fixing white vitreous china urinal partitions

Providing, fixing, testing and commissioning of hand drier with nuts and washer of approved brand including cutting and making good the walls wherever required as directed by Engineering Incharge.

Supply, fixing, testing and commissioning of tissue paper holder of approved brand with relevant eccessories including cutting and making good the walls wherever required as directed by engineering Incharge.

Laying, jointing and testing DWC HDPE PIPE SN-8 as per IS-16098 laid to correct levels below ground in trenches upto required depth including excavation in all kind of soil including (hard rocks) dewatering, refilling, watering, ramming and removing the surplus excavated material and shifting within the site limit as directed by site incharge and making good the same complete as required. Concrete bad / brick soling etc as per shown in the detail drawings. 150DIA

(a) Constructing Inspection pit for Sewerage systems of inside measurement and depth as described below with 250 mm thick 1st class brickwork in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and outside walls upto G.L. and 20 mm thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick RCC slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia RCC manhole cover with required frame of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit, with earth and removing spoils after work complete in all respects with all costs of labour and materials. (NOTE: CHAMBER RATE SHALL BE EXCEPT MANHOLE COVER). 600x600 SEWERAGE PIT UPTO (-750)

750x750 SEWERAGE PIT ABOVE (-750 TO -1000)

Supplying, fitting and fixing in position 35 MT load bearing capacity (for placing on the road area) Reinforced cement polymer concrete/PFRC 560 mm round manhole cover with frame for Inspection Manhole provided with two lifter hooks fitted with matching frame of size 600 mm round

Supplying, fitting and fixing in position 15 MT load bearing capacity (For placing at other than road area) Reinforced cement polymer concrete/PFRC 560 mm round manhole cover with frame for Inspection Manhole provided with two lifter hooks fitted with matching frame of size 600 mm round

(a) Constructing manhole pit of inside measurement DEPTH AS DESCRIBED BELOW with 250 mm thick 1st class brickwork in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and outside walls upto G.L. and 20 mm thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick RCC slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia RCC manhole cover of approved make fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit, with earth and removing spoils after work complete in all respects with all costs of labour and materials. (NOTE: Chamber rate shall be except manhole cover) 600x600 STORM PIT UPTO (-750)

750x750 STORM PIT ABOVE (-750 TO -1000)

Providing fitting and fixing wash basin complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. A) Kohler Make

Providing M.S. foot rests WITH RUBBER COATED including fixing (wherever required as per the instruction of site Engineer as a special case) with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design. (a) With 20x20 mm square bar.

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified. (Note: Ball valve and union will be charged extra and does not comes under Accessories) (i) In internal wall - exposed on wall 65 mm od

WATER TREATMENT PLANT Supply, installation, testing & commissioning of vertical MSEP filter with adequate dirt holding capacity (suitable for 3 Kg/Sqcm working pressure). Fabricated from MS sheet as per manufacturer's specifications complete with intitial charge filter media including painting inside with two coats of non toxic epoxy and with one coat of zinc chromate two coats of synthetic enamel paint outside. Including concrete foudation with cement plaster complete as required. The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (heavy) and butterfly valves designed on 1.50 m / sec velocity. a. Dual Media Filter for Domestic Water services. FLOW Rate 5 CUM/HR, Working pressure 3Kg/Sq.cm Flow rate 3 LPS Considering eight hours operation

b. Activated Carbon Filter -FLOW Rate 5 CUM/HR, Working pressure: 3Kg/Sq.cm Flow rate 3 LPS, Considering eight hours operation

Supplying, installing, testing and commissioning of dosing system (for domestic water treatment plant) consisting of one HDPE tank of 200 litres capacity with a positive displacement diphragm dosing pump having variable flowrate of 0-6 lph. The motor shall be suitable for operation at 240 V/single phase/50 Hz. Supply. The pump shall be supplied complete with necessary polypropylene piping, valves, strainers, low level switch and injection fittings. The pump shall be speed & stroke control Asia LMI / equivalent make.

Supply, installation, testing and commissioning KIRLOSKAR / BE / GRUNDFOSS / WILO / DP make Pump motor set (located in semi-underground Pump house) for lifting / forcing water from a chamber of U.G. Reservoir to WTP to Domestic water chamber of the same Reservoir of required drive (Motor HP), having discharge capacity and pumping head as described below with support clamp/lifting device separate or common base frame with all electrical accessories, with over load protection relay power cable and control cable from MCC to respective motors, earthing including other accessories (recommended by manufacturer) etc., such as 100 mm dia. pressure gauge (range 0-15 Kg./Sq.cm.) with control cock fitted on delivery line, coupling of required size on suction and flexible removable type (Flanged) coupling on delivery end of pump, required M.S. galvanised supporting frame complete operational. (a) Lift Pump : (Filter Feed Pump) (i) A set of two nos of Mano Block feed Pump Motor set (1 operating, 1 standby) : Duty Condition of each pump 5 Kl./Hr. @ of 30 m Pumping head.

Supply, installation, testing and commissioning KIRLOSKAR / GRUNDFOSS / WILO make Pump motor set (located in underground Pump house) for lifting / forcing water from a chamber of U.G. Reservoir to Centralise Over Head Reservoir, or to Irrigation network at ground level or to Elevated Storage Tank placed on building roof, of required drive (Motor HP), having discharge capacity and pumping head as described below with support clamp/lifting device separate or common base frame with all electrical accessories, with over load protection relay power cable and control cable from MCC to respective motors, earthing including other accessories (recommended by manufacturer) etc., such as 100 mm dia. pressure gauge (range 0-15 Kg./Sq.cm.) with control cock fitted on delivery line, coupling of required size on suction and flexible removable type (Flanged) coupling on delivery end of pump, required M.S. galvanised supporting frame complete operational. (a) Lift Pump : (For Domestic) (i) A set of three nos of Centrufugal manablock transfer (End Suction & Top Discharge) Pump Motor set (2 operating, 1 combined standby) : Duty Condition of each pump 9 Kl./Hr. @ of 35 m Pumping head from (UGR to OHR of Block - 1 & 2

(b) Lift Pump : (FOR FLUSHING) (i) A set of two nos of Centrufugal manablock transfer (End Suction & Top Discharge) Pump Motor set (1 operating, 1 standby) : Duty Condition of each pump 9 Kl./Hr. @ of 35 m Pumping head from of Block - 1 & 2

IRRIGATION PUMPING SET Sump pumps (Non-clogging type) in Basement : Supply, installation, testing and commissioning KIRLOSKAR /GRUNDFOSS / WILO make Submersible type non-clogging Pump motor set (2 nos. of Pumps located in each sump in semi-underground pump house) of required drive (Motor HP), having discharge capacity and pumping head as described below with all electrical accessories viz.main switch and starter, auto on/off system with float arm (with fixed or flexible arm), over load protection relay, power cable and control cable from main switch and starter with auto on-off with dry running protection to respective motors, earthing having required M.S. galvanised supporting stay/ clamp etc. complete operational. A set of two nos Sump pumps (Non-clogging type) having discharge capacity of each pump approx.7.5 cum/hr at 15 m. pumping head (1 working, 1 standby) Suction from sumps in underground pump house, delivery to surface drain at ground level. Including MCC and allied works (PUMP ROOM)

Supply, installation, testing and commissioning KIRLOSKAR / GRUNDFOSS / WILO make Submersible type non-clogging Pump motor set (2 nos. of Pumps located in each sump in semi-underground pump house) of required drive (Motor HP), having discharge capacity and pumping head as described below with all electrical accessories viz.main switch and starter, auto on/off system with float arm (with fixed or flexible arm), over load protection relay, power cable and control cable from main switch and starter with auto on-off with dry running protection to respective motors, earthing having required M.S. galvanised supporting stay/ clamp etc. complete operational. i) A set of two nos Sump pumps (Non-clogging type) having discharge capacity of each pump approx.7.5 cum/hr at 15 m. pumping head (1 working, 1 standby) Suction from sumps in STP underground pump house, delivery to surface drain at ground level. Including MCC and allied works (

ii) A set of two nos Sump pumps (Non-clogging type) having discharge capacity of each pump approx. 3.6 cum/hr at 15 m. pumping head (1 working, 1 standby) Suction from sumps in underground HARVESTING TANK, delivery to surface drain at ground level. Including MCC and allied works (FOR HARVESTING STORAGE TANK)

Supply, Fixing, jointing, testing and commissioning of uPVC pipe confirming to ASTMD 1785 SCEDULE-80 cut to required lengths including all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door). Fixing at wall / ceiling level supported by G.I. clamps, hangers, angle support etc. for basement sump drainage out let to external drainage chamber. (b) 40 mm dia

(c) 50 mm dia.

(d) 65 mm dia

(e) 80 mm dia

Providing and fixing cast iron"Y" strainer with flange ends with pressure rating of PN-1.0 of approved quality as per IS (a) 100 mm dia

(b) 80 mm dia

Providing and fixing cast iron non-return valve with flange ends with pressure rating of PN-1.0 of approved quality as per IS: 5312 (a) 32 mm dia.

(b) 40 mm dia.

(c) 50 mm dia.

(d) 65 mm dia

(e) 80 mm dia

Supplying, fitting and fixing Suitable Ball valve having all cast iron components as per I.S. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 MT per sq.cm. spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to I.S. 780/71, painted black all over with asphalt base paint tested to 21 kg (Hydraulic pressure) per sq.cm. valve opening to anticlockwise direction, supplied, fitted and fixed complete. (a) 32 mm dia.

(b) 40 mm dia.

Supplying & Fixing,cast iron body Butterfly Valves with matching flanges, rubber insertion, nuts, bolts and washer etc (IS:13095) of following size complete as reqd. (a) 50 mm dia.

(b) 65 mm dia.

(c) 80 mm dia.

(d) 100 mm dia.

Providing & fixing dial type Pressure gauge of (0-16kg/cm2) range with gun metal shut off cock etc. duly calibrated before installation in MKS and FPS units and fixing the same where required as directed including all fittings, short piece, nipples, elbows testing the joints etc.all complete. (Quantity of this item will be payable only where it has not been included in the relevant composite items).

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately). 32mm dia

Supplying, fitting and fixing in RCC walls or floors etc. Puddle collar assembly/sleeves consisting of MS pipes(Heavy type) conforming to IS : 1239 and IS : 3589 having required shell thickness, both ends flanged drilled to IS specification and one end matching blank flange(welded to pipe) with nuts, bolts, washers etc.and MS collar of minimum 6 mm thickness of specified size welded all round the pipe complete including three coats of bituminous paint on concealed portion and a coat of zinc oxide primer and two coats of synthetic enamel paint of approved shade on the exposed portion of the puddle collars as per direction of Engineer-in-charge. f) 50 mm Puddle Flange

g) 25 mm Puddle Flange

Providing and fixing Water Level Monitor (Water Gauge) for installing on the side wall of Water Reservoir consisting of calibrated bore transparent tube with back ground board, floating indicator, drainout valve etc.complete operational.(Water level difference upto 4 m.) - For Under ground Reservoir.

TUBE WELL 25 KL/HOUR DISCHARGE CAPACITY 2 Nos. Tube well BOQ Labour for boring through any type of soil for sinking tube well of required dia. with top enlargement by rig boring system (either by reserve circulation or by direct rotary method) including hire charges and labour for rig machine, tools and plants, staging, force pumping set and making arrangement for water required for boring etc. complete and lowering of pipes, strainers, blind pipes etc. complete. (b) For depth upto 350 metre for Casing of 200 x 150 mm dia. Tube well with top enlargement of 200 mm dia.(upto 50 metre). (i) First 50 metre

(ii) Next 50 metre

(iii) Next 50 metre

(iv) Rest 100 metre

(iv) Rest 100 metre

Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with 'V' notch including hire and labour charges for all tools and plants and scaffolding as required.

Surging of existing tube well with chemical treatment and bucket wash (prior to use of compressor machine) and developing the tube well with compressor machine at least 3 (three) days at 8 (eight) hours per day till the yield is obtained at least by 75% of the total specified yield of the tube well (measured by 'V' notch tank) and draw down is within the permissible limit of 10% variation and water so obtained after such washing and developing will be free from sand and bacteria for which test report from the Public Analyst is to be obtained. (The rate is inclusive of all labour and materials including hire charges of tools and plants and cost of materials.) (a) For tube well size bigger than 100mm with top enlarged to have yield 25000 ltrs per hour. N.B. This item is to be executed with the special approval of the Engineer-in-charge.

Labour for making arrangement for showing verticality test including the cost for hire charges of tools and plants, scafolding, labour etc. all complete.

Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction.

Packing the annular space between the outside of the tube well pipes & strainers and the bore with pea size washed gravel of approved quality having size from 2 mm to 5 mm or the size approved by the Engineer-in- charge including cost of all materials labour and equipment complete.

Note: Initial 6 m. of Annular space between the housing pipe and the bore should not be shrouded with Pea size gravel to avoid contamination with surface water. Packing annular space between the outside of the housing pipe and the bore with puddled clay balls of approved size as per direction of the Engineer-in-charge with cost of all materials and labour complete.

Providing and fixing bell plug as required upto 200 mm (internal) dia. ERWMS pipe including cost of materials and labour complete.

Geophysical investigation of the acquifer by electrologging system with all tools and plants as necessary including supply of necessary report.

Supply & Installation of G.I. Class `B' column pipe with flanges at 3m intervals including all fittings, flanges, clamps as required. 80 mm dia

Supplying,fitting and fixing Gun Metal Wheel valve (horizontal) G.M. tested to 21 kg per sq. cm. (i) 80 mm dia

Supplying PVC strainer of approved make with adapter conforming to I.S.12818 specifications. 150 MM DIA

Supplying and lowering uPVC Casing Pipe (Heavy Duty) as per IS: 12818 - 1995 200 mm dia

150 mm dia

Supply,testing commissioning and lowering of submersible pumps set(enclosed in Cage) by using GI `B' class column pipes (pipes including in seperate cloumn of schedule) upto approximate depth of 30 mts including binding submersible cable, alongwith column pipes with suitable size of clamps. The submersible pump set with direct coupled motor rated for 3 phase, 50 cycle 415 ± 10% volts A/c supply with the following duty along with suitale rated panel. Total head - 50 mts. Approx. Flow rate - 25000 ltr/ hr. (Considering four hour operation per day)

Supplying,fitting and fixing check valve (horizontal) G.M. tested to 21 kg per sq. cm. (i) 80 mm dia

Supplying, fitting and fixing 250 mm M.S. housing clamp of approved quality.

Supplying, fitting and fixing G.I. cap at top 200mm dia. well cap.

Supplying, fitting and fixing heavy type bell mouth reducing socket. (v) 150 mm X 200 mm

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

Supplying fiting and fixing PVC double ‘Y’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

Supplying fiting and fixing PVC double ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

Supplying fiting and fixing PVC cross ‘T’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm x110mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm x110mm

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 110 mm x 90 mm

Supplying fiting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110 mm x 90 mm

Supplying fiting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. 110 mm x 75mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (a) 110 mm

Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (b) 110 mm

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (ii) 110mm dia. PVC cowel of ISI make

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. 75mm dia. PVC cowel of ISI make

Providing fitting and fixing C.P. Grating (ii) 110mm dia

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified. (Note: Ball valve and union will be charged extra and does not comes under Accessories) (i) In internal wall - exposed on wall (f) 50 mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified. (Note: Ball valve and union will be charged extra and does not comes under Accessories)(ii) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages (a) 15 mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified. (Note: Ball valve and union will be charged extra and does not comes under Accessories)(ii) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages (b) 20 mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified. (Note: Ball valve and union will be charged extra and does not comes under Accessories)(ii) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages(c) 25 mm OD

Providing , fitting and fixing PVC flush pipe cutting and making good to the floors and walls where necessary.

Providing , fitting and fixing CI/MS brackets for wash basin and sink complete as directed and specified.

Providing fitting and fixing PATIO URINAL SENSOR of category V Sensor (Code-24199IN-C01-CP) including necessary accessories etc. as per the direction of engineer incharge A) Kohler Make

Providing fitting and fixing vitreous china Wall Hang water closet (European type W.C pan with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, if required. (Flushing Cistern to be paid separately) A) Kohler Make

Supplying fitting and fixing chrome finish Basin Tap 1/2 with 200mm Extension Body of approved brand (Code-OPP-CHR-15021PM)) as directed and specified. (G.I. & C.P pipes will be measured and paid separately)

PVC CONDUIT WIRING Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2X 1.5sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

PVC Conduit (Surface) Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required 20 mm

Metal Boxes Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100 mm x 100 mm x 60 mm deep (Nominal size

150 mm x 150 mm x 60 mm deep (Nominal size

200 mm x 250 mm x 60 mm deep (Nominal size

200 mm x 300 mm x 60 mm deep (Nominal size

250 mm x 300 mm x 60 mm deep (Nominal size

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell Push

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mm X 75 mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module

8 Module

12 Module

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 6 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door

12 way , Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, iclusive of 200 A tinned copper bus bar, common neutral link, earth bar,din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Double pole

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 26 mm X 5 mm G.1. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. lades, 0 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

SWITCH & SOCKETS Supplying with fitting fixing of 6/10 amp two way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of electronic modular fan speed controller 2 - module type MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department. 120 watt electronic modular 5 step speed control 2 - module

Supplying with fitting and fixing of RJ-11 Telephone jack , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including fitting and fixing of TV co-axial outlet MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module including making necessary connection complete as per direction of department.

Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying of wall mounting combination fuse switch unit (HRC) with steel enclosure TPN fuse switch unit, 415 volt A.C complete with HRC fuses and all accessories etc. as required 630A

Moulded Case Circuit Breaker (MCCB) "Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved by the Deptt. as specified and directed by the deptt." 63A

Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 125A

Isolator "Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt." 40A

Supply of loadkontak isolator triple pole, 415 volt A.C complete with all accessories suitable to fix on a din-bar etc. as required 40A

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. 35.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

70.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

95.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

120.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

150.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

185.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

240.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

35.00 Sq. mm.4 Core armoured U.G. cable

50.00 Sq. mm.4 Core armoured U.G. cable

70.00 Sq. mm.4 Core armoured U.G. cable

4.00 Sq.mm 3 Core armoured U.G. cable

C o m p r e s s i o n G l a n d "SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) SINGLE compression BRASS GLAND HEAVY DUTY" SINGLE compression BRASS GLAND HEAVY DUTY Size: 3/4"

SINGLE compression BRASS GLAND HEAVY DUTY Size: 3 - 1/2"

TELEPHONE WIRES & CABLES "Provide and draw petroleum Jelly filled Telecommunication cables polythene insulated & sheathed copper conductor 0.5mm dia armoured in existing surface/ recessed conduit wiring system complete as required" Supplying ,installation, testing & commissioning of 20 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

EARTHING SYSTEM "Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid Copper tube having 85 mm dia. single prong at top and 3 mm thick base plate at bottom complete with fitting & fixing with Brass nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt." LIGHTNING ARRESTER

1C 50SQMM CU UNARMOURED GREEN COLOUR CABLE in 25mm HMS PVC Conduit

1C 70SQMM CU UNARMOURED GREEN COLOUR CABLE in 25mm HMS PVC Conduit (FOR LA)

EPABX SYSTEM Supply, installation and commisioning of EPABX system as specified and directed by the deptt.

1C 35SQMM CU UNARMOURED GREEN COLOUR CABLE in 20mm HMS PVC Conduit

1C 6SQMM CU UNARMOURED GREEN COLOUR CABLE in 20mm HMS PVC Conduit

Supply,installation,testing and commissioning of 50x10mm Cu equipotential bar of 300mm length in 450x450x300 mm PVC junction box to conect earthing strips from earth pit as well as cable going for equipment earthing

Supply,installation,testing and commissioning of 50x10 mm GI equipotential bar of 300 mm length in 450x450x300 mm PVC junction box to conect earthing strips from earth pit as well as cable going for equipment earthing

Supply and Installation of - LV. PANEL BOARDS Indoor Type complete with Manpower, Loading/Un-loading, Equipments, Tools and consummables as per the drawings, Specifications & the standareds as designated below, Including Testing & Commissioning. DP HVAC

INDOOR LUMINIARIES (Note: Bad lights,chandilier and other decorative light not considered) All light fixtures are with electronics ballast with THD value of less than 10%. The rate shall include the cost of lamps, poles, foundation for street lights and other accessories required for installation Indoor Luminiaries (supply and installation) PHILIPS//WIPRO/CROMPTON/JAQUAR NOTE : LIGHT BOQ OF PHILIPS - EQUIVALENT PRODUCT OF BRAND AS MENTIONED ABOVE CAN BE USED LED 36S-6500 PSU OD WH PIR

BBS170 1xDLED -5000 PSU WH

DN190B LED3S-6500 PSU WH

SP310X LED 22S-6500 PSU OD WH

DN311B LED6S-4000 PSU MB WH

BBS175 1xDLED -5000 PSU WH

RC380B LED32S-6500 L120W30 PSU OD

SM200C LED16S 6500 PSU OD WH

WT202W LED6S NW PSU S2 PC

Supplying and Fixing following rating, double pole,(Sigle phase and neutral), 240 V , residual current circuit breaker (RCCB),having a sesitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25A

Supplying and Fixing following rating, four pole,(Three phase and neutral), 415 V , residual current circuit breaker (RCCB),having a sesitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A

Suplying and Fixing CAT -6 Internet Cablen for LED display in Passanger lift including conduit pipe with connections, testing and commissioning etc. as required and as per direction of engineer incharge.

Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS- 694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push Zencelo make. GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover, ceiling rose Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Pole Type BOP or equivalent-7030 Height 7m The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO , Base Plate Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts:- 6.8 Gr. As per IS 1367, Pole Sections :- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening :- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. (A/ 70mm Bottom Dia. (A/ 130mm , Sheet Thickness 3mm , Base Plate dimensions :- (L x B x 220 x 220 x 12, Foundation Bolt , Bolt Size :- (no. x dia.) 4 x 20 Dia, Pitch Circle Dia. (PC 205 Bolt Length 750, Projected Bolt Length 100mm, Anchor plate thickness:- 4 mm , Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation:- The foundation shall be done with ( Earth work:- 2.04 cubic Meters.RCC :- 1:1.5 : 3 proportion 0.65 cubic metres. Steel :- 22.43 Kg. Shuttering :- 4.32 square metres. = 22.43 Kg.

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make)Stiffener plate from arm of the following types : Single arm bracket 1500mm long for 3m to 10 metre. Poles.

Item :- Supplying, installation testing and commissioning of pressure die cast powder coated aluminium alloy housing frosted PC diffuser, IP 65/IP66 protection of the 90 W LED street light including connection cable with 2.5 sqmm 3 core PVC insulated round copper conductor as required and as directed by the department (Crompton or equivalent Make)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

15/16 A switch

6 pin 15/16 A socket outlet

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required 125 A,36KA,FPMCCB

250 A,36KA,FPMCCB

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fitting fixing of crompton Capacitor Type propeller type ac ventilating fan-exhaust including necessary connection etc. as required complete and as directed by the Department.

Supplying and fitting fixing of Philips 18W HL Yes 5 Star 1250 for 18W HL with 6500 K G-13 including necessary connection etc. as required complete and as directed by the Department.

Supplying with installation testing and commissioning of ‘G’ Frame Panel Boards ,250 A “AA” Frame MCCB, Outgoing 6 ways (IHVGF2500600) as approved and directed by the Deptt. Note(This item is not available in GEM portal)

Supplying, installation,testing and commissioning of crompton 36W Led Recessed Luminaire complete with all accessories etc. including necessary connection as required complete and as directed by the Department.

Supplying including drawing of Philips 18W Led Recessed Luminaire (DN296) complete with all accessories including necessary connection as required complete and as directed by the Department

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Supplying including erection testing and charging of 3 phase 33 KV H.T. O.H. line on G.I. steel tubular pole 14.5 m SP-76 using ACSR Wolf conductor with channel cross arm, (average span 60 m) (4 Structure-2 nos, DP-1No

3 Phase 4W combined CT/PT Accuracy class 0.2, 400/5A, STC 25kA for 1 Sec

0.5 Class 1Ph outdoor CT with GI mounting structure & marshaling box (set comprising of three units) 600-300/1-1A, 5 kA for 3 sec

33KV/11V 1Ph outdoor PT with GI mounting structure & marshaling box (set comprising of three units)

Battery charger 110V suitable for charging 100AH, 100V battery bank, dual mode double circuitry SCRvaiac float & boostcharger.

33KV VCB 1250A WITH GI Mounting structure.

33KV RMU (21kA, 63A 3way non extensible)

Load Security

Ground Floor Reception 3 seater sofa

Reception Table

Mid Back Revolving chair

Center table

Medical Room Fowler Bed

6 seater Table

Mid Back revolving chair

General Area 6 seater Table

Mid Back revolving chair

Publication Room Plain Almirah

Table 1200*600 with pedastral

Mid Back revolving chair

Meeting Room 6 seater Table

Mid back chair

Program chair cabin Main desk with ERU 1650*700*743 Main Desk 1000*450*743 ERU

High back chair

Visitor chair

Program Office Table 1200*600 with pedastral

Table 1200*600 with pedastral

Mid back chair

Waiting area 3 seater sofa

Library 6 seater Table

Glass 4 door bookcase

Relax sledge based with arms

Enterprise table 1500W with CPU hanger

Mid back chair

Computer Room Middle main desk with ERU 1650*700*743 Main Desk 1000*450*743 ERU

High back chair

Up. Back To Back 4 seater WOrkstation Module

Mid back chair

Conference room 10 seater Table

Mid back chair

Middle main desk with ERU 1650*700*743 Main Desk 1000*450*743 ERU

High back Chair

center table

2 seater sofa

3 seater sofa

Chairman room Main table with ERU attached pedastral 1800*2100*750

High back chair

Visitor Chair

GD room 10 seater Table

Mid back chair

1st Floor Waiting area 3 seater sofa

Center table

Class room 1,2 & 3 Finesse table -4020 1200*600

Mid back chair

Two Seater SM6 Desc Cum Bench

Seminar room (2 rooms) Relax Full Desklet with Wiretray

Finesse table -5630 1650*900

Mid back chair

3rd Floor Waiting Lobby 3 seater sofa

Center table

Work Station Wish Recta 1200*600 with pedastral

Mid back chair

10 seater Table

mid back revolving chair LC(1 room 8 chairs)

Admin support office (6Rooms) Finesse table -5026 ERU 3616 with Pedestal 1500*750*740 Main desk 1050*450*705 ERU

High Back LC Chair

Visitor Chair

Plain Almirah

Faculty Room (18 Rooms) Finesse table -5026 ERU 3616 with Pedestal 1500*750*740 Main desk 1050*450*705 ERU

High Back LC Chair

Visitor Chair

Plain Almirah

Insight Table 1665W 1665*900*740

Fourth floor Waiting Lobby 3 seater sofa

. center table

Faculty Room (18 Rooms) Finesse table -5026 ERU 3616 with Pedestal 1500*750*740 Main desk 1050*450*705 ERU

. High Back LC Chair

. Visitor Chair

Plain Almirah

Insight Table 1665W 1665*900*740

Board room 30 seater conference table

. High back chair

. mid back chair

. 3 seater sofa

. center table

Dean's Room Cignus main table with ERU attached pedestal 2350*2350*750

Back unit 2350*500*1800

High back chairs

visitor chair

4 door bookcase

3 seater sofa

Dean's Office . 3 seater sofa

. 2 seater sofa

Aristo main table with ERU attached pedastral 1800*2100*750

. High back chair

Thrill full back mesh chair

4 door bookcase

Wish Recta 1200*600

Common room White Black Board(9.8 x 3.9 ft)

Curtain Set of 2 ( 9 ft x 4.3 ft)

Self Adhesive Acrylic Information Signage of Size: 1.5 ft x 0.5 ft

Supply, fitting and commissioning of 1. HP 200 Pro G4 54.6 cm (21.5) All-in-One Desktop PC having specifications 12th Generation Intel® Core™ i3 processor FreeDOS Intel® UHD Graphics 4 GB DDR4 RAM 1 TB SSD Solid State Drive 1 HDMI-out 1.4, 1 headphone/microphone combo, 1 power connector, 1 RJ-45,2 USB 2.0, 2 USB 3.2 Gen 1

Supply, fitting and commissioning of HP Laserjet Tank MFP 1005W,Wireless,Print,Copy,Scan,Specifications: Hi-Speed USB 2.0,Bluetooth Monochrome Laser Printers Le,Up to 22 Ppm,150-Sheet Input Tray,100-Sheet Output Tray,1-Year Warranty,Black&White,381U4A

Supply, fitting and commissioning of ZEBRONICS U1205 Microcontroller Based UPS with Up-to 1000VA | 600W, Specification: Double Boost, Automatic Voltage Regulation, Overload Protection, Auto Restart, Generator Compatible, for Office Computers |

WATER PURIFIER Providing and placing of Aquaguard Reverse OsmosisWater Treatment System 50 LPH Aquaguard (50 LPH STORAGE)as approved by Architect & the Department.

CLASSROOM 73 SEATER Providing, Installation, Commissioning, Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges setup with 1. 4600 Lumens Laser Projector of Make - EPSON (or similar) and Model-EB-L260SW 2. MOUNTING KIT of make NT(or Similar) with 2ft + 2ft decent 3. MOTORIZED SCREEN 137",16:10 with S/R of make Milan(or Similar) 4. HDMI transmitter receiver of make Lindy(or Similar) , Model- 38208 5. 1 mtrs. HDMI Cable of make Lindy(or Similar) , Model- 36961 6. Wooden Podium with HDMI & XLR port of make Universo(or Similar) , Model-UN108 7. HDMI faceplate 8. Goosneck Mic for Digital Podium of Make Earthpot(or Similar) , Model- VI518GN 9. Audio DSP of Make Earthpot(or Similar) , Model- Keyer 442 10. Channel Amplifier of make Sonodyne(or Similar) , Model- SLA3003 11. Column Speaker with clamp of Make Sonodyne(or Similar) , Make - CA410 + A400WB 12. Audio Cable of Make Belden(or Similar) , Model- 1813A 13. Speaker Cable of make Belden(or Similar) , Model- 8473 14. Lan Cable of Make Dlink(or Similar) , Model- CAT6 15. Connectors, Model and Make Branded

Seminar Hall 48 Seaters Providing, Installation, Commissioning, Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges setup with 1. 3700 Lumens LCD WXGA Projector of Make Epson(or Similar) , Model- EB-W06 2. MOUNTING KIT of make NT(or Similar) with 2ft + 2ft decent 3. MOTORIZED SCREEN 137",16:10 with S/R of make Milan (or Similar) 4. HDMI transmitter receiver of make Lindy(or Similar) , Model- 38208 5. 1 mtrs. HDMI Cable of make Lindy(or Similar) , Model- 36961 6. Goosneck Mic for Digital Podium of Make Earthpot(or Similar) , Model- VI518GN 7. Audio DSP of Make Earthpot(or Similar) , Model- Keyer 442 8. Channel Amplifier of make Sonodyne(or Similar) , Model- SLA3003 9. Column Speaker with clamp of Make Sonodyne(or Similar) , Make - CA410 + A400WB 10. Audio Cable of Make Belden(or Similar) , Model- 1813A 11.Speaker Cable of make Belden(or Similar) , Model- 8473 12. Lan Cable of Make Dlink(or Similar) , Model- CAT69U Rack of Make WQ 13. Connectors, Model and Make Branded

Meeting Room Providing, Installation, Commissioning, Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges setup with 1. 65" Interactive Display of Make Samsung(or Similar), Model- BE65D 2. Faceplate on table (with HDMI only) of Make Branded and Model Branded 3. 5 mtrs. HDMI cable of Make Lindy(or Similar) and Model -36965

Conference Room Providing, Installation, Commissioning, Design and Consultancy , User Training, Site Survey,Drawings – (conduiting layouts, schematics etc. )and documentation charges setup with following requirements- 1. Audio Cable of Make Belden(or Similar) and Model-1813A 2. Control Cable of Make Belden(or Similar) and Model- 8723 3. LAN Cable of Make Dlink(or Similar) and Model- CAT6 4. Connectors (XLR, Sheilded RJ45) of Branded Make and Model 5. 17 U Rack of Make WQ (or Similar)and Model-17U 6. Control System of Make Extron(or Similar) and Model-IPCP Pro 250 xi 7.License for Control System of Make Extron Control(or Similar) and Model-Extron control 8. i-Pad for Controlling all the equipment of Make Apple and Model Ipad 10.2" 64GB, Wifi Silver/Grey 9. 16 Port Network Switch of D-Link (or Similar)and Model DGS-F1018P-E 10. Wireless access point of Make TP Link (or Similar)and Model- EAP660 11. Docking station for i-Pad of Make- Iport-Connect and Model-IPORT - CONNECT PRO - Case for iPad(or Similar) 12. Base Station for i-Pad of Make- Iport-Connect and Model-IPORT - CONNECT PRO - BaseStation(or Similar) 13. Delegate Unit of Make Erthpot(or Similar) and Model-NCS 5DF + NGM516 14. Chairman Unit of Make Erthpot(or Similar) and Model-NCS 5DF + NGM516 15. Contol Unit for Chairman Delegate of Make Erthpot(or Similar) and Model-NCS-110CU 16. Gooseneck Mic for Podium of Make Erthpot(or Similar) and Make- VI518GN 17. Audio Signal Processor of Make Erthpot(or Similar) and Model- Keyer 444 18. Channel Amplifier of Make WorkPro(or Similar) and Model- PA1254 19 Column Speaker with clamp of Make Workpro(or Similar) and Model-NEO 5 20. PTZ Camera with 12x zoom of Make Lumens(or Similar) and Model- VC-R31 21. HDMI transmitter receiver of make Lindy(or Similar) and Model-38208 22. 1 mtrs. HDMI Cable of make Purelink (or Similar)and Model-36962 23. HDMI to USB Scaller of make Innogenni (or Similar)and Model-4KUSB3 24. 5200 Lumens Laser Projector of Make Epson(or Similar), Model- EBL-570U 25. MOUNTING KIT of make NT with 2ft + 2ft decent(or Similar) 26. MOTORIZED SCREEN 169",16:10 with S/R of make Milan(or Similar) and Model- MOTORIZED SCREEN 169",16:10 with S/R 27. 43" Display for Chairman of Make Samsung(or Similar) and Model 43BU800 28. Faceplate on table (with HDMI, USB & Power only) of Make Branded and Model- Branded 29.HDMI switcher with wireless presenation of Make Altona(or Similar) and Model- MS52W 30. HDMI transmitter receiver of Make Lindy(or Similar) and Model-38208 31 Wooden Podium with HDMI & XLR port of Make Universo(or Similar) and Model-UN108 32. 10 mtrs HDMI Cable of Make Lindy (or Similar)and Model- 36967 33. 1 mtrs. HDMI Cable of Make Lindy(or Similar) and Model- 36962

Supplying and drawing of UTP 4 Pair CAT 6 LAN Cable in the existing surface/recessed steel/PVC Conduit as required 1 run of cable

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required 20 mm

D-Link 16 Port Gigabit Ethemet ports for fast network speeds and backwards compatibility

D-Link 24 Port Networking Switch 48 Gbps Switching Capacity.

D-Link 4 U wall mount enclosures

D-Link I/O Box

D-Link Rj 45 connectors

D-Link Keystone

pvc box

patch cord (3 Meter)

Supplying, installation,testing and commissioning of IMPULSE 3MP IP DOME CAMERA complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of Matrix 5MP IP BULLET CAMERA complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of TISHA 4000 GB SATA HD Hard disk drive complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of Q-100 Port Fast Ethernet PoE Switch with 2 Gigabit Uplink, 8 10/100Mbps PoE RJ45 port (port 1~port 8) complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of NUMAX Online UPS of Rating 1.0 KVA With Battery Of Backup Time 30 Minutes complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of finolex Control cable for CCTV complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of CP PLUS 32 Channels NVR with 12 MP (4000 X 3000) complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of LG Smart Television Tv 50 Inch LED Backlit LCD complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of Round PVC Passive Networking Flexible Pipe (DURABLE FELXIBLE PVC PIPE ROLL 1") complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

Supplying, installation,testing and commissioning of WQ India 19U Rack Enclosures Networking/Server Rack complete with all accessories including necessary connection and earthing etc. as required complete and as directed by the Department.

YARD HYDRANT (EXTERNAL FIRE) WORKS Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (For Above Ground) 80 mm dia

150 mm dia

Supply, installation, testing & commissioning of MS Heavy duty pipe (IS:1239/IS:3589) heavy class including cutting, screwing, welding etc. complete with fitting viz. tees elbow, bends, flanges, reducers etc. including providing anti-corrosive treatment (coating and wrapping) with 4 mm thick tape and holiday test check as per IS:10221, 50mm sand filling around the pipe complete as required. All sub soil piping shall be treated as per IS code & shall only be carried out after inspection and permission of the Engineer-in- Charge. FOR UNDER GROUND PIPING. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 150 mm dia

80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

100 mm dia

150 mm dia

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Weather proof hose cabinets for internal hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 750mm x 600mm x 300mm).

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

PUMP HOUSE WORKS Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 65mm dia

80mm dia

200mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 200mm dia

Providing & Fixing of C.I. Foot Valve of following sizes and complete in all respect with all labour, tools & plants, transportation, taxes, levies etc. and as per specification, drawing and direction of Engineer-in-charge. 100mm NB

Providing and installation of GM Ball Valve, IS-318 LTB-2 SS Stem AISI 410, Ball SS 304/CF8, teflon gland packing, screwed female threads to IS-554, a) 25 NB

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing dial type (100 mm dia) pressure gauge with isolation ball valve suitable for working pressure of 250 PSI. Cost shall be inclusive of providing any short pieces, nipples, elbows etc as required. (For Ground and Terrace floor). Non schedule item

Control and expander moudules. Dress Plate. Battery dress plate. Chassis low profile. Dress Panel blanck covers. Cost of fault isolator complete with base

Cost of intelligent addressable smoke detector

Cost of control module for talk back system

Cost of manual call point

Cost of Horn cum strobe

Cost of fire fighter telephone handset

Cost of fire fighter phone jack

Cost of wall mounted loud speaker, 3/1.5 Watt in ABS enclosure

Cost of Fire alarm armoured FRLS cable 2 x 1.5 sqmm

Speaker cable of following pairs ,cores and size of PVC insulated FRLS copper conductor cable with LHC in the existing surface / recessed steel conduit / PVC casing and capping including connections etc. PVC CONDUIT 20 MM DIA

Cost of single pair 2-core 48/0.2 mm, speaker cable

Supply, instalation, testing & commissionig of Addressable monitoring module to connect NO/NC contacts such as pressure switch, flow switches, fire pump contacts (provided by Fire fighting contractor). Panel shall be located at Security room and reception area.Approved Make:VIGNARTA (APOLLO) / RAVEL/NOTIFIRE

PA SYSTEM (TALK BACK SYSTEM) Supplying, installing, testing and commissioning solid state Amplifier of 250 W RMS out put in rack, including necessary control wires, jocks etc. complete.

Supplying, installing, testing and commissioning of P.A. Console 8 zone with priority module micro processor based, mixing amplifier, power supply unit & goose neck micro phone etc.

Supplying, installing, testing and commissioning of P.A. Call station of 8 zones with priority module micro processor based & goose neck micro phone etc shall be located in the reception / security for the announcement necessary communication cable/CAT 6 shall be considered form PA controller to call station .

Supplying, installing, testing and commissioning of P.A ceiling speakers

SIGNAGES Supply and installation in position the "FIRE EXIT" Sign with luminicent colour having size 300 x 100 mm

Supply and fixing in position the signages " FIRE ORDER" contain the following matter on 3 mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyle painted foam board of size 1200 x 1000 mm.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and of required shade complete as required : (Maximum of 350 meter pipe can be used including all dia) 80 mm dia

150 mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 80mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150mm dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supply installation of Air release valve complete with 25 mm dia brass air valve with nipple, tees, elbow, pipe and all accessories as required.

Supply installation of brass ball valve complete with 25 mm with nipple, tees, elbow, pipe and all accessories as required.

MS Union for fixing Ball Valve for drain line connection

Supply, Installation of Structural steel (Angle & Channel) for supporting purpose for pipe dia 100 mm dia and above.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supply, Providing & fixing 150 mm dial type Pressure gauge of (0-16kg/cm2) range with gun metal shut off cock etc. duly calibrated before installation in MKS and FPS units and fixing the same where required as directed including all fittings, short piece, nipples, elbows testing the joints etc.all complete. (Quantity of this item will be payable only where it has not been included in the relevant composite items).

Providing & fixing Water based Carbon-di-oxide 9 ltrs. fire extinguishers as per IS specification consisting of welded MS cylindrical body ,squeeze lever discharge valve fitted with internal discharge tube ,30 cm long high pressure discharge hose ,discharge nozzle,suspension brackets,finished exteranally with red enemel paint and fixed to wall with brackets with rawl plug/dash fastners complete with initial charging.

Providing & fixing ABC type (Dry powder type ) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Weather proof hose cabinets for internal hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 750mm x 600mm x 300mm).

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80mm dia

150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700mm length

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

CORE CUTTING 200 MM DIA FOR 150 MM PIPE

100 MM DIA FOR 80 MM DIA PIPE

HIGH SIDE WATER CHILLING UNIT Installation, testing and commissioning of Screw-type Chiller with actual capacity not less than 250 TR, suitable for ambient conditions, with AHRI certification all as specified hereinafter.(2 working and 1 Standby) [i] Installation, testing and commissioning of floor-mounted compact screw-type chiller machine complete with semi-hermatic twin screw type compressors with independent circuits, water-cooled S/T type condenser, S/T horizontal flooded type evaporator with carbon steel shell and seamless copper tubes with 19 mm nitrile rubber insulation, common base frame, interconnected copper refrigerant piping and wiring, vibration isolators, gauge panel, automatic safety controls, flow switch at evaporator and condenser and ozone friendly CFC-free refrigerant gas R-134a/407C. The refrigerant flow control shall use an electronic expansion valve. The chiller shall be designed for a working pressure of 150 psig and hydraulically tested at 225 psig. A number of properly spaced baffles shall be provided for maintaining optimum water velocity and heat transfer and the tubes shall be adequately supported. [ii]Chillers shall be factory AHRI tested at design conditions at 100%, 75%, 50% and 25% load respectively; test certificates shall be produced for all chillers. The chiller shall be BMS compatible and shall have RS485/RS232 serial communication protocol; the motor shall be suitable for 3- Phase, 415 V ± 10%, 50 Hz AC electric supply; electric panel shall have an IP 54 rating, as per specification and drawings. The chiller shall be as per the approved particular technical specifications and shall meet the following design criteria: Chiller Chilled water in : 54o F Chilled water out : 44o F Chilled water flow rate: 840 USGPM Fouling Factor : 0.0005 (FPS) Condenser Condenser water in : 90o F-88 F Condenser water out : 97.5o F-95.5o F Condenser water flow rate: 1680 USGPM Fouling Factor : 0.001 (FPS) NOTE : Necessary civil work viz. PCC foundation for placement of chillers shall be covered in the scope of work

PUMPS Supply, Installation, Testing and Commissioning of Horizontal axially split casing/ End suction pumps complete with motor , base frame, vibration isolators and other accessories (except suction and discharge shut off valves, suction strainer,discharge check valves and drain piping which are covered under separate items.) Pumps shall have mechanical seal and Bronze Impeller. The pump motor shall be suitable for 415 ± 10%, 50 cycles, 3 phase power supply, squirrel cage induction 1450 RPM TEFC motor. The quoted price shall include cost of thermal insulation and cladding for chilled water pumps,(earthing,control wiring and main cable for electrical panel to unit with cable tray with necessary accessories, are covered under separate items) M.S. base frame for mounting both pump and motor, as per required civil foundation with viberation isolators. Pumps shall be complete as per specifications and shall have operating parameters as given below : NOTE : Necessary civil work viz. PCC foundation for placement of pump, mounting of star/delta starter panel and pump accessories shall be covered in the scope of work. The pump shall be as per the approved particular technical specifications and drawings. Primary Chilled water pumps Water flow rate : 600 USGPM Head : 12M Motor HP : 10 HP(suggested) (1 No. standby pump included in above quantity)

Condenser water pumps Water flow rate : 1200 USGPM Head : 12M Motor HP : 15 HP(suggested) (1 No. standby pump included in above quantity)

Secondary chilled water pumps Water flow rate : 600 USGPM Head : 40M Motor HP : 15 HP(suggested) (1 No. standby pump included in above quantity)

Microprocessor based BMS compatible, variable frequency speed controller complete with necessary fittings and wiring

Expansion Tank Providing and installation of expansion tank, fabricated out of 6 mm thick M.S. plate construction, duly insulated as per the specifications and shall be complete with 50mm dia outlets for system connection and overflow, make up connection, overflow connection, drain connection, drain valve, vent connections, valves and fittings as required. Expansion tank shall be complete with insulation as per specifications and drawings. SIZE : 1000 mm X 1000 mm X 1000 mm (high)

LOW SIDE Air Handling Unit Supply, installation, testing and commissioning of double skin modular construction, draw through Ceiling Suspended (CS) / Floor Mounted Horizontal type (FM) Air Handling Units of 0.6 mm thick Plain GSS Sheet from inside & 0.6 mm thick Preplasticized GSS Sheet from Outside. AHU Shall be complete with DIDW Centrifugal fan, Squirrel cage induction motor, cooling coil (Copper tubes and Aluminium fins), pre-filter (Washable Synthetic fibre of efficiency 90% down to 20 micron), drain pan, V belt drive, fireproof double canvass connection and other accessories as per specifications (except water shut off valves, drain piping, Thermometer and pressure gauges which are covered under separate item). Motor shall be suitable for 415 ± 10% volts, 50 cycle, 3 Phase AC supply as indicated below. 3400 CFM / 8.5 TR CS AHU, 40MM SP

4400 CFM / 11.0 TR CS AHU, 40MM SP

3600 CFM /9.0 TR CS AHU, 40MM SP

3200 CFM /8.0 TR CS AHU, 40MM SP

3000 CFM /7.5 TR CS AHU, 35MM SP

2800 CFM /7.0 TR CS AHU, 35MM SP

2400 CFM /6.0 TR CS AHU, 35MM SP

2000 CFM /5.0 TR CS AHU, 35MM SP

1800 CFM /4.5 TR CS AHU, 35MM SP

Fan Coil Unit 1.0 TR / 1.5 TR

3.0 TR High Static

3.0 TR Normal

Chilled Water Cassette Unit 1.0 / 1.5 TR, CH.W. Cassette Unit

2.0 / 2.5 TR, CH.W. Cassette Unit

1.8 TR, Standard DX Hi-wall Unit for Server Room.

Inline Fans Supply, installation, testing and commissioning of inline ducted Fans as shown in drawings. Fan motor shall be suitable for single phase, 50 Hz AC supply. The capacity of the fan given as under:- Duty : Toilet Exhaust Air Quantity 400 CFM Static Pressure : 20mm Motor Rating : 250 Watt.

Fan Section Supply, Installation, Testing and commissioning of Single skin Fan Section as shown in drawing and as per specifications. Each unit shall be complete with casing (16G) DIDW centrifugal fan, belt drive, motor, louvers etc. The quoted price shall include cost of starter, wiring and cabling from electrical panel to unit with conduit/ cable tray. Fan motor shall be suitable for 3 Phase, 415 ± 10% V, 50 Hz AC supply. Duty :Lift Pressurization (Fan At Terrace) Air Quantity : 8800 CFM Static Pressure : 40 mm wg Motor Rating :5.5 KW

Duty :Staircase Pressurization (Fan At Terrace) Air Quantity : 6000 CFM Static Pressure : 40 mm wg Motor Rating : 3.7 KW

Duty :Common corridor smoke exhaust (Fan At 4th Floor) Air Quantity : 5000 CFM Static Pressure : 40 mm wg Motor Rating : 3.7 KW

Duty :Common corridor smoke exhaust (Fan At 1st to 3rd) Air Quantity : 4000 CFM Static Pressure : 40 mm wg Motor Rating : 3.7 KW

Supply, installation, testing and commissioning of cooling thermostats for various Air Handling Units and Fan Coil Units as per specifications including all accessaries ,mountings,wiring between thermostat & unit, terminations etc. Proportional thermostats for Air Handling Units

Drain Piping Providing and fixing in position the following PVC pipe cut to required length including necessary fittings (bends, tees, unions, sockets etc) as per specifications & complete with nitrate foam 9 mm thick insulation sleeves on horizontal lines only as required as under - 80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Supply and instalation of M.S. Steel structure of c sections/ I girder/ Squre pipe/ m. S. plate/ M. S. angle/ M. S. Chequre plate as reduired for plateform for possioning of equipments complete with Anchoring of chemical fasteners as required.

Supply & fixing of sintex storage tank with float valve, makeup and quick fill ball valve and drain valve and over flow connections complete with capacity 5000 litre for Cooling Towers.

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. "Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above." 250mm dia.(75 mm thick insulation)

200mm dia.(75 mm thick insulation)

150mm dia.(75 mm thick insulation)

125mm dia.(75 mm thick insulation)

100mm dia.(75 mm thick insulation)

80mm dia.(75 mm thick insulation)

65mm dia.(75 mm thick insulation)

50mm dia.((50mm thick insulation)

40mm dia.((50mm thick insulation)

32mm dia.((50mm thick insulation)

25mm dia.((50mm thick insulation)

INSULATED VALVES "Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications." BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot water circulation as specified 250 mm Dia

200 mm Dia

150 mm Dia

100 mm Dia

80 mm Dia

65 mm Dia

50 mm Dia

Ball Valve 50 mm Dia

40 mm dia

32 mm dia

25 mm dia

15 mm dia

Providing and fixing in position the following Ball Valves with strainer duly insulated as per specifications and drawings 25 mm dia

40 mm dia

32 mm dia

25 mm dia

20 mm dia

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 200 mm Dia

150 mm Dia

80 mm Dia

65 mm Dia

50 mm Dia

40 mm Dia

32 mm Dia

Y-STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 200 mm Dia

150 mm Dia

65 mm Dia

50 mm Dia

40 mm Dia

32 mm Dia

Motorised Butterfly Valves Supply, installation, testing and commissioning of motorised on / off butterfly valves with modulating motor in return chilled water line of each chiller & Hot Water Generator operated through BMS & of following sizes. Valves shall be insulated as per pipe insulation material & thickness given above. 250 mm Dia

200 mm Dia

150 mm Dia

Rubber / Flexible bellow 200 mm Dia

150 mm Dia

CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. And from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 300 mm Dia

250 mm Dia

200 mm Dia

150 mm Dia

100 mm Dia

Flow Swich

25 mm dia auto air vent valve

19 mm dia auto air vent valve

15 mm dia auto air vent valve

Pressure Gauges Supply, installation, testing and commissioning of pressure guage of approved make of dia 150 mm conforming to tender specifications.

Thermometer Providing & fixing in position the mercury in glass industrial type thermometers.

1/4" Test Point

DUCTING, GRILLS, DIFFUSER AND INSULATION Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following required. Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying & fixing of powder coated extruded aluminium Grills without aluminium volume control dampers as per specifications.

Supplying & fixing of aluminium collar dampers complete as required.

Supplying, fixing testing commissioning of powder coated aluminium louver with bird screen.

Supplying, fixing testing commissioning of motorised fire damper.

Supplying, fixing testing commissioning of actuator & electrical wiring for motorised fire damper.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Supply and fixing of acoustic lining of supply air duct and plenum with 15 mm thick open cell nitrile rubber sheet, complete as required and as per specifications.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm

Main AC Panel a) Water Cooled Screw Chiller, 250 TR, 270HP approx (2W+1S), Each b) CHW Pr. Pump for Chiller, 10 HP Each, (2W+1S) c) CDW Pump for Chiller, 50.0 HP Each, (2W+1S) d) Phase I - CHW Sr. Pump - 25.0 HP Each, (2W+1S) e) Cooling Tower Fan Motor, 03 x 25 HP (2W+1S) Supply, installation, testing and commissioning of Cubical type sectinalised floor standing switch board by CPRI apprved firms of 31 MVA fault capacity at 415 V complete with 4 strip, 600 A capacity Aluminium Bus - Bar Electrolytic grade E-91, cable alley, switchgears suitable for AC-23 duty & of following capacity & as per specification and drawing

AHU's Starter Panels Supply, installation, testing and commissioning of electrical panel of required raitings for AHU complete with on/off the air handling unit with incomer MCB, DOL starter with contactor & overload relay, single phase preventer, on/off push botton, on/off indication light, ammeter, sheet steel encloser & compatible for BMS as required for different AHU motors rating from 1.0 HP to 5.0 HP.

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. 3.5C × 185 sq.mm. AL. XLPE Armored CABLE

3.5C ×35 sq.mm. AL. XLPE Armored CABLE

3C × 25 sq.mm. AL. XLPE Armored CABLE

4C × 10 sq.mm. AL. XLPE Armored CABLE

3C / 4C × 6 sq.mm. AL. XLPE Armored CABLE

3C x 2.5 sq.mm. CU. PVC, Armored CABLE

Supply, fixing, connection, testing and commissioning of double compression brass cable glands and crimping type lugs / sockets with necessary tools and equipments as specified in specifications and IS. The glands and lugs / sockets shall be suitable for cable size and type mentioned above. The job also includes, if necessary, supply and fixing of extension busbar of same material on circuit breaker / FSU or panel board terminal / connector to connect more than one no. of parallel cables or to connect higher size cable to lower size unit. The job also includes earthing the glands and armour of the cable with common earth bar or flexible copper mesh. 3.5C × 240 sq.mm. AL. XLPE Armored CABLE

3.5C × 185 sq.mm. AL. XLPE Armored CABLE

3.5C ×35 sq.mm. AL. XLPE Armored CABLE

3C × 25 sq.mm. AL. XLPE Armored CABLE

3C × 16 sq.mm. AL. XLPE Armored CABLE

4C × 10 sq.mm. AL. XLPE Armored CABLE

CABLE TRAY Supply, Installation, laying and connection of G.I. perforated type cable tray for the entire HVAC workwith necessary bands, tees and clamps/couplers for fixing. All material shall be Hot dip galvanized as per Specifications. Standard length shall be 2.5 meters. 750 mm. wide. - vertical member-100mm x 2 mm thick, rungs-40x25 mm @300 mm,

600 mm. wide. - vertical member-100mm x 2 mm thick, rungs-35x15 mm @300 mm,

450 mm. wide. - vertical member-100mm x 2 mm thick, rungs-35x15 mm @300 mm,

300 mm. wide. - vertical member-100mm x 1.5 mm thick, rungs-35x15 mm @300 mm,

150 mm. wide. - vertical member-100mm x 1.5 mm thick, rungs-35x15 mm @300 mm,

Supply and Laying of suitable GI strip Earthings for entire HVAC system / package 25mm x 3 mm GI strip

50mm x 5mm GI strip

8 / 6 SWG GI wire

Supply, installation, testing and commissioning of synthetic fill pad type double skin air washer at 500 FPM velocity across pads, DIDW Class-I forward curved centrifugal fan with TEFC weather proof motor of IP:55 protection suitable for 415 +10% Volts, 3 phase, 50 cycles power supply, mounted on a common base with metallistik vibration isolators, multi sheave pullies for fan and fan motor. The fan capacity shall be based on outlet velocity not exceeding 2000 FPM. The cooler shall be complete with 8" thick celdek fill, 3mm thick FRP steel reinforced tank, water pump 2 Nos. (1+1), cover pipe, distribution pipe, distribution pan, filters at air inlet, water piping, make up water with ball valve, drain and overflow connection, all housed in 16 G GSS casing mounted on vibration isolators complete in all respects as per specifications and drawings. Capacity of coolers as under; Necessary starter panels are includeed. 9000 cfm capacity for kitchen

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold setting adhesive (CPR X compound complete as per specifications and as required. - 25 mm thick

Supply, Fabrication and Erection of Fire retardant Flexible canvas connection for AHU / FCU / TFA / FAN, etc.

HTE INFRA LLP (BID ID -291579)