LAYING, TESTING AND COMMISSIONING OF UNDERGROUND STEEL PIPELINE ALONG WITH ASSOCIATED WORKS FOR SONEPAT, MEERUT AND DEWAS (18 MONTHS ARC)

Amount

1.CARBON STEEL PIPES

PIPELINE LAYING / INSTALLATION BY OPEN CUT / HDD / MOILING (WITHOUT CASING) METHOD

"Receiving and taking over" as defined in the specifications, handling, loading, transportation and unloading of Owner supplied 3-Layer PE coated and bare linepipes from Owner's designated stack-yard to Contractor's stock yard/workshop/work-site including preliminary activities, preparation of drawings, wherever required for crossing etc. including handling, stacking, stringing on the pipeline Right-of-Use/ pipeline route alignment corridor, carrying out inspection of company supplied materials including linepipes at the time of taking over, laying/ installation of coated linepipes as per specification wherever required depending on site condition including execution of all works, "taking over", handling , including loading and unloading, transportation of Owner supplied materials other than linepipe from Owner's designated place (s) of issue to work site, arrangement of all additional lands required for Contractor's storage, fabrication, access for construction, procurement and supply of all materials (except Owner supplied materials), consumables, equipment, labour and other inputs, carrying out all temporary, ancillary, auxiliary works, ready for commissioning of pipeline as per drawings, specifications, other provisions of Contract document and instructions of Engineer-in-charge, including but not limited to carrying out the following works:

Surveying of route and detours required at the time of execution including marking the same in topographical sheet, preparation of construction drawings showing survey details, and submit same to Owner for review / approval.

Staking and installation of construction markers, clearing, fencing, grubbing, full filling all the requirements of various statutory/ environment authorities to the entire satisfaction of concerned authorities. During construction, methodology of laying of steel pipeline (i.e. open cut/ HDD/ moling without casing) shall be decided as per requirement of various Government statutory/ environmental/ local authorities and the same methodology of steel laying shall be binding to the contractor for Authority's entire satisfaction. Grading / clearing of work area and shifting of all obstruction within the ROU/ Pipeline route alignment corridor viz. electrical lines/ poles, telephone line / poles, foreign pipeline, etc.

Barricading the pipeline construction area prior to execution of the works as per drawings enclosed with tender document and to the entire satisfaction of Owner / Engineer-in-charge.

Carrying out repairs of pipe defects/ replacement in case of irreparable defects and repairs of defects of pipe coating not attributable to Owner including defects/ damages occurring during transportation / handling.

Stringing of line pipes along pipeline trench / ROU / Pipeline route alignment corridor provided on sand/soft soil bags including all supplies, manpower & machinary etc.

Checking, cleaning, aligning, bending, cutting and bevelling (as required) of pipes for welding and field adjustments including pipe fittings, welding, carrying out non-destructive testing of welds as required including 100% radiography by X-ray either by internal source or external source based on site conditions/front availability and in this regard decision of EIC shall be final and binding to the contractor [In case placement/installation of X-ray equipment is not feasible, in that case Gamma ray may be permitted as per decision of Engineer In-Charge(EIC) based on site conditions] and providing all requisite equipment, labour, supervision, materials, films, consumables, all facilities and personnel to process, develop, examine and interpret radiographs and other tests as required, carrying out repairs of weld joints found defective by Engineer-in-Charge, carrying out re-radiography and other tests as required on repaired joints.

Carrying out installation of carrier line pipe at all minor crossing viz. road, cart track, pathway, water bodies etc. (for which ROU width limit of the crossings are less than or equal to 6.0 meters) at designated depth by open cut / HDD / Moiling (except at major crossing by HDD method / Cased crossing as mentioned elsewhere in the SOR item).

Carrying out installation of carrier line pipe in the casing pipe at cased crossing (excluding installation of casing pipes which is covered separately).

Coating of field weld joints, long radius bends (R=3D), elbows, buried fittings and valves etc. including supply of coating materials etc. (i.e. heat shrinkable sleeves and high build epoxy etc.) as per PJS & Technical Specification compatible with 3 layer PE coating material of the line pipe.

Supply of LR Bend (R=3D) of material equivalent to pipe material grade (i.e API 5L Grade X-42/46/52/56/60) and of all size, all thickness, all angle etc. suitable to connect / fit with intended steel pipeline to be laid, as per specification and their complete Installation with steel pipeline network of all size & thickness as per specification wherever required depending on site condition.

Carrying out air cleaning, pigging, flushing, cleaning, Gauging (if feasible as per site condition or as per pipeline alignment & geometry, deceision of EIC in this regard shall be final & binding to the contractor) and hydrostatic testing of complete pipeline, supply of required quantity of corrosion inhibitor, if required including pre-testing of designated sections complete as per specification and approved by Engineer–in–charge to specified pressures indicated elsewhere and duration after stabilization as per specification, providing all equipment, pumps, fittings, instruments, dead weight tester, pressure recorder, thermocouples etc., and services, supervision, labour, consumables, water including supply of corrosion inhibitor, air, etc. as required, locating of leaks and rectification of defect attributable to Contractor (rectification of defects in linepipe material not attributable to contractor shall be paid separately as per other item of schedule of rate), re-testing after rectification, dewatering after successful completion of hydrotesting of entire section and as approved by Engineer-in-Charge. However payment for the Gauging shall be made as seprate items mention else where in the SOR.

Note: Leak detection, its rectification and successfully re-hydrotesting shall be carried out by Contractor with a view that completion of all activity for successful hydrotesting is not inordinately extended, which will hamper the overall project schedule. Further, no extra payment claim shall be entertained for re-hydrotesting and leak detection if defects found attributable to Contractor.

All tieing-in, including the tie-in(s) of the pipeline with the adjacent sections of pipeline including cutting of test header, rebevelling as required, radiography and other NDT examination, joint coating as per specification.

Final clean-up & restoration of ROU/ Pipeline route alignment corridor or area disturbed by contractor including obtaining NOC from respective land owner and statutory authorities during their construction activities for laying of pipeline works and disposal of debris and returning all surplus material to designated disposal areas / storage yard as and backfilling of trench/ pits/ ditches and compaction of the same as per satisfaction of Owner and / Or as directed by Engineer–in–charge. However, restoration of top disturbed surface if required, i.e Asphalt / Bituminous / Concrete / Metal / Red stone roads / Pavement / Pavor block / Tiled / Brick lined including compaction of soil, to original condition as per requirement and to the entire satisfaction of EIC and / or concerned Owners having jurisdiction and shall be paid as seprate items mention else where in the SOR.

Restoration of land, facilities and boundary wall etc. and associated facilities dismantled/ damaged by the Contractor during construction;

Installation of all burried valves with postive isolation inside the valve pit are required either to terminate the pipeline or to be kept as provision for the hook-up with the future pipeline.

Protective coating of 1000 micron thick two component (applied with the help of minimum three coats) liquid epoxy including supply of materials duly approved by Owner for all piping valves, fittings, structural steels etc. for buried installation and inside the valve pit as approved by the Engineer-in-charge.

Carrying out all temporary, ancillary, auxiliary works and all incidental works required to make the pipeline ready for pre-commissioning;

Hook-up work with existing pipelines.

Obtaining work permits/ NOC from various statutory authorities having jurisdiction, before and after execution of the work, and complying with all stipulation/ conditions/ recommendation of the said authorities;

Preparation of as-built drawings, pipe-book and other records as specified in the specifications. SOR shall be read in conjuction with job specific requirements, specifications, standards, drawings and other provision of contract document. All above works of line pipe laying and installation for buried pipeline as per following details:

For Open cut method:

Trenching to all depths and to a width to accomodate the carrier pipeline during lowering by excavation in all types of underground strata ( including soils, pebbels, cobbles, boulders, structures and all type of rockey strata) including raking up of built-up surface / Hard surface of any type including metal road/ surface, concrete road/ surface, bituminous road/ surface, asphalt road/ surface, etc. which is breakable in pieces shall be carried out either by breaking, chiselling or otherwise cutting etc manually or using pneumatic machine. Further raking up of built-up surface of any type includes tiled surface, paver block, brick lined etc.which is breakable/removable in pieces shall be carried out mannualy without using pneumatic machine. All tiles/ slabs/ paver block/ curb stones etc.removed during excavation shall be placed properly and storing excavated soil, reusable materials at designated area as directed by Engineer in charge and to a width to accommodate the pipeline as per the relevant standard/ specification etc. [The cover of pipeline shall be in between 1.0 meter to 1.5 meters depending upon site conditions and shall be measured from top of pipeline coating to the top of undisturbed surface of the soil or as per SCC/ relevant code, whichever is higher]. Dewatering of trenches if required as per site condition. Padding & Backfilling of the trench after lowering the pipeline. [However,Raking up of built-up surface / Hard surface of any type including metal road/ surface , concrete road/ surface, bituminous road/ surface, asphalt road/ surface etc. which is breakable in pieces shall be carried out either by manually or using pneumatic machine and tiled surface, paver block, brick lined etc.which is breakable/removable in pieces manually shall be carried out without using pneumatic machine and proper placement of all tiles/ slabs/ paver block/ curb stones etc. removed during excavation shall be paid as separate items mentioned else where in the SOR].

Supply of warning mat for all sizes of pipeline in multiple lot based on site condition/requirement and their installation over the entire length of the pipeline laid in open-cut trench as per specification. Warning mat for pipeline shall be supplied as per the technical specification enclosed in the bid document. The material of warning mat shall be of high density polyethylene and non-biodegradable type. It shall have non-toxic and anti-rodent properties.

Supply and installation of slope breakers, wherever required or, as directed by Onwer / Engineer–in–charge.

Crossing of all-foreign pipeline / HT line / cable / any other utilities etc. with necessary concrete / PVC protection including coordination with all agencies and obtaining NOC.

Installation of bank protection & associated works along with supply of all types of backfill materials etc. duly approved by EIC for pipeline trench and banks falls under minor water body crossing as per technical specification & Std. Drg., wherever required or, as directed by Owner / EIC.

Training and diversions of streams in steep slope area, wherever required.

For HDD method

Complete work of laying of pipeline in restricted ROU along with adjacent road/nala (if minor road/nala falling under the laying profile and not considered under separate crossing) by HDD method including "Receiving and taking over" owner supplied 3LPE coated line pipes from owner's designated place to issue/dump site(s) and transportation to contractor's stock yard/work site including all handling, loading, uploading, aligning etc. supply of all contractor supplied material including consumables, manpower, equipment, other resources to work site(s) and aquiring the required land for storage. Execution of, but not limited to, following works in accordance with specifications and instruction of engineer-in-charge and as per all provision of Contract Document.

Pre-construction survey, necessary cover required over the carrier pipeline, based on site visit, collection of data (if required) from concerned Authority including design and detail engineering and making of drawings for getting their approval from concerned Authority/Engineer-in-charge, getting work permit/NOC for utlities crossings (if any) encounterd prior to start the execution of work.

Drilling to required depth from top of ground (min 2.0 mtrs.) including maintenance of drill hole in all types of underground strata ( including soils, pebbels, cobbles, boulders, structures and all type of rockey strata , all depth to accommodate the pipeline at all conditions encountered by approved HDD methods for providing minimum cover specified in code/specification or the actual depth as decided by concerned authority, whichever is more.

Laying of the pipeline by the approved HDD method including pipeline string preparation, welding, testing, 100% radiography by X-ray, welding repair and retest, coating of field joints with special type Dirax Heat Shrink Sleeve or equivalent (including supply of coating material) and repair of pipeline coating with special PERP-80 repair patch or equivalent material (including supply of repair patch) as per specification, pre-hydrotest of complete strings made for laying etc.

Backfilling of the Pits/ Ditches/ Trench including restoration and clean-up of area, disposal of drilling fluid & waste etc. to the satisfaction of Engineer-in-charge and/or as directed by concerned Authority.

Gauging (if feasible as per site condition or as per pipeline alignment & geometry), Pigging, Cleaning for Post installation hydrotest and carrying out further Post installation hydrotest, dewatering and tie-in with pipeline at either banks or other adjusant pipeline section maintaining minimum pipeline cover 1.0 to 1.5 meter etc. all other works including pigging, Cleaning, final hydrotesting etc. alongwith mainline works(as mentioned above) required as per specifications, codes, approved drawings, calculations, methods and as directed by Engineer-in-charge and provision of contract document, getting NOC from all concerned authority of the facillities. However payment for the Gauging and Post installation hydrotest shall be made as seprate items mention else where in the SOR.

For Manual/ Machine Moiling technique (without Casing)

Survey of under ground utilities, execution of the work as per specification, including excavation of pits moling with the hole size not exceeding 20% of the pipe dia, jointing and insertion of carrier pipe, testing & commissioning and restoration of the pits to original condition, submission of As-Built Graph as per specifications and the instruction of Engineer-in-charge.

Specified dia Thk (mm) Material Coating Type Length of each pipe (mm) NB

For all types of underground strata ( including soils, pebbels, cobbles, boulders, structures and all type of rockey strata)

250 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

200 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

150 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

100 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

This item shall be applicable for the laying/ installation of underground steel grid main pipeline & branch pipeline including bends (R=3D) and associated works to complete the pipeline system. Installation of underground/ aboveground tap-off for distribution pipelines, valves of all type/size/ratings, barred tees, insulating joints, flanges & fittings, accessories etc. and including fabrication, NDT, Testing & Installation of SVs (all types), tie-in of valve assembly including radiography of tie-in joints as per Schematic Layout Drawings and technical Specification alongwith aboveground approach pipeline upto Insulating Joint (including installation of aboveground / underground insulating joint) for various stations are required to complete the pipeline system, however payment for the same shall be made through separate SOR items mentioned elsewhere in the SOR.

Supply of all valves, flanges, fittings, assorted pipes, barred tees & insulating Joints, etc. shall be paid by separate item mentioned elsewhere in SOR.

Contractor shall not perform any pipeline related activities along the ROU/ Pipeline route alignment corridor without specified barricading/ permission of EIC/ RCM as per Std. Drg. and other safety measures.

The quantities mentioned above are tentative and may increase or decrease depending upon the site conditions/requirements of Geographical Area (GA). The quantity indicated against each item are to be carried out at multiple and/or different locations within the GA and shall be decided by EIC as per requirement at site.

A large part of the proposed pipeline route is along MDR/ Asphalt Road / concrete roads (RCC/ PCC) etc. However, in case of non-availability of ROU/ Pipeline route alignment corridor along MDR/ Asphalt Road / concrete roads (RCC/ PCC) etc., the pipeline route may change and this may also require a new tap-off point at suitable location on Pipeline. This may cause increase / decrease in SOR quantities.

The above items rate shall be applicable for underground laying / installation of Coated Line Pipes either by open cut method or by HDD method or by moiling (without casing) method or in any combination depending on site conditions and laying / installation methodology shall be proposed & submitted by the contractor for approval of EIC. Further upon approval of laying / installation methodology by EIC, Contractor shall start the execution of laying / installation works of burried pipeline at site.

The above items rate shall be applicable for all locations / region/ charge area within & around the GA.

The above rate is excluding of major crossings by HDD, Boring, moiling Method mentioned under separate item.

Contractor shall ensure that no tree/ plant cutting shall be carried out during Pipe Line Laying operations.Trenching shall be carried out manually if needed, so as to ensure no damage to plant/ tree/ OFC / water pipe line / telephone line/ sewage line/ electric cable and other under ground utilities.

Contractor have to use rock cutting tool and all other accessries as required to make drill hole in case of rocky starta.

Payment for carrying out liasioning & co-odrination works for utility/ foreign pipeline crossings (if any) and obtaining permission / NOC from these authorities including assistance in ROU opening & closing and their maintainence/ management both side of the crossings shall be made by separate SOR item mentioned elsewhere in this SOR.

RAKING UP OF BUILT-UP SURFACE/ HARD SURFACE FOR LAYING / INSTALLATION OF PIPELINE

Raking up of built-up surface / Hard surface of any type including metal road/ surface , concrete road/ surface, bituminous road/ surface, asphalt road/ surface etc. which is breakable in pieces shall be carried out either by breaking, chiselling or otherwise cutting etc manually or using pneumatic machine. Further, built-up surface of any type including tiled surface, paver block, brick lined etc.which is breakable/removable in pieces manually shall be carried out without using pneumatic machine. All tiles/ slabs/ paver block/ curb stones etc.removed during excavation shall be placed properly. All other activities for pipeline laying/ installation shall be carried out as per mainline laying activities SOR item code.: A00100 including its notes and payments for the same shall be made accordingly from the quoted sub SOR items of SOR item code. A00100

250 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

200 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

150 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

100 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

REMOVAL & RESTORATION OF CONTINEOUS CONCRETE ( RCC/PCC) FOR LAYING / INSTALLATION OF PIPELINE

Removal of contrete (RCC/PCC etc) for prepration of pipeline trench (by using pneumatic machine or other approved method) including restoration of same as previous by providing the RCC/PCC...etc up to satisfaction of EIC and concern authority. Shifting & disposing of debrish material at suitable location as per direction of EIC. All other activities for pipeline laying/ installation shall be carried out as per mainline laying activities SOR item code.: A00100 including its notes and payments for the same shall be made accordingly from the quoted sub SOR items of SOR item code.: A00100

250 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

200 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

150 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

100 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

RESTORATION OF ROADS

Restoration of Asphalt / Bituminous / Concrete / Metal / Red stone roads / Pavement / Pavor block / Tiled / Bricklined including compaction of soil, to original condition as per requirement and to the entire satisfaction of EIC and / or concerned Owners having jurisdiction for following thickness :

Restoration of Asphalt / Bituminous road upto 10 cm thickness

Restoration of Asphalt / Bituminous road beyond 10 cm and upto 20 cm thickness

Restoration of Concrete / Metal road upto 10 cm thickness

Restoration of Concrete / Metal road beyond 10 cm and upto 20 cm thickness

Restoration of red stone road / pavement / pavor block / tiled / bricklined upto 4 inch thickness

Restoration of red stone road / pavement / pavor block / tiled / bricklined beyond 4 inch and upto 8 inch thickness

BORROWED LOCAL SOIL FOR BACKFILLING

Additional work over and above (Sl.no.1) for supply of specified and approved quality of borrowed local soft graded soil / sand in place of available excavated material and / or other suitable soil as per applicable standards / specifications, including backfilling of excavated trench for specified length after laying and padding of pipeline, including local transportation of such special backfill material over all distances, complete.

CONTINUOUS CONCRETE WEIGHT COATING (FOR CS PIPES)

Supply of all consumables, materials and application of 60 mm thk. continuous concrete weight coating of minimum density 2245 kg/m3 of minimum grade M-35 for 10"/8"/6"/4" NB Line Pipe and field joints thereof in all areas of work wherever required as per site condition and performing all works as per specification on the line pipe for following sizes :-

Specified OD 273.0 mm x 6.4 mm W.T.

Specified OD 219.1 mm x 6.4 mm W.T.

Specified OD 168.3 mm x 6.4 mm W.T.

Specified OD 114.3 mm x 6.4 mm W.T.

1. This item shall be operated alongwith SOR item code.: A00100 (including its notes ) above for anti-boyancy in marshy lands, small water body crosssings like nala , canal , ponds , water channel etc. as per instruction of EIC based on actual site condition. 2. Laying of Pipeline in marshy land/area and dain/nala shall be payable to contractor as per quoted sub-SOR items under SOR item code.: A00100 (ncluding its notes) & its concrete weight coating applied over the pipe shall be paid through above SOR items.

PIPING FABRICATION & INSTALLATION WORKS FOR SECTIONALISING VALVE STATION (WITH FUTURE TAP-OFF/ WITHOUT FUTURE TAP-OFF)

SECTIONALISING VALVE STATION (WITH FUTURE TAP-OFF/ WITHOUT FUTURE TAP-OFF) - UNDER GROUND

All works for installation of all piping Underground at all depth for Vent Type/ No Vent Type Sectionalising Valve Station (WITH FUTURE TAP-OFF/ WITHOUT FUTURE TAP-OFF) in Valve Chamber all type of terrains and soils including transportation and handling of all owner/contractor supplied materials i.e. full bore 10", 8", 6" & 4'' Ball valves (fully welded body & butt welded end), Plug Valves (( butt welded end)), all types of other valves of all sizes, Flow tees/Weldolet of all sizes, Insulating Joint, vent line pipes for mainline, assorted pipes and all flanges and fittings from designated places(s) of issue to work site. Supply of gaskets, studs, nuts,copper jumpers, nipples & coupling etc. Installation / Erection of instrumentation items i.e. pressure gauge, consumables, manpower, machineries, tools & tackles for carrying out all mechanical works of underground and above ground piping including fabrication, welding, nondestructive testing of welds, weld repairs/ Pretesting, cleaning/ flushing, pre-hydrotesting & hydrostatic testing, dewatering, functional testing, cutting of mainline and bevelling (if required), tie-in of valve assembly, including radiography of tie-in joints, corrosion coating (by heat shrink sleeves) for burried piping and external painting for buried fittings by high build epoxy of min. 600 micron of R-95 or equivalent as required, obtaining all statutory clearances, approvals and permissions for the works (wherever required), making of valve pit [for detail refer relevant drawings (i.e. P&ID, Plot Plan) for SV Station enclosed with tender document, pipe supports including all associated civil works ( pertaining to supports only); painting, finishing, clean-up and restoration of site; preparation of as-built drawings, documents and project records and performing all works as per drawings, specifications, other provisions of Contract document and instructions of Engineer-in-charge.

Sectionalising Valve Station ( 10" ) - With future Tap-off

Sectionalising Valve Station ( 10" ) - Without future Tap-off

Sectionalising Valve Station ( 8" ) - With future Tap-off

Sectionalising Valve Station ( 8" ) - Without future Tap-off

Sectionalising Valve Station ( 6" ) - With future Tap-off

Sectionalising Valve Station ( 6" ) - Without future Tap-off

Sectionalising Valve Station ( 4" ) - With future Tap-off

Sectionalising Valve Station ( 4" ) - Without future Tap-off

Notes: 1. This work is exclusive of all works associated with main pipeline covered at elsewhere in SOR (Sl.no.1). 2. All Civil/ structural works except for piping supports will be paid separately as per rates provided elsewhere. 3. Work is inclusive of receiving, taking over, loading & unloading of company supplied material and return of surplus material to Company's designated stockyard/store. 4. Incase of bought-out items, supply of Valves, Assorted Pipe, fittings & Flanges,IJ, instrumentation work...etc shall be paid as per item rates mentioned elsewhere in the SOR. Fabrication of SV, erection, Testing & commissioing are included in above item rates, hence contractor have to quote accordingly. 5. Valve Pit and its upper slab for under ground SV stations (with/without future Tap-off) shall be payable through separate item rates mentioned elsewhere in the SOR.

(Refer relevant drawings for Sectionalising Valve Stations (with/without future Tap-off) enclosed with tender document for ascertaining quantum of works associated with SV Station).

PIPING FABRICATION & UNDERGROUND/ ABOVEGROUND INSTALLATION WORKS OF TAP-OFF LINE AT PROPOSED LOCATION / POINT ON MAIN STEEL PIPELINE.

All works for underground/ aboveground installation of all piping and valves assembly at all depth for Tap-off in all type of terrains and soils including transportation and handling of all owner/contractor supplied materials butt welded Ball valve, all valves of all types and sizes , Barred tees of all sizes and all fittings from designated places(s) of issue to work site. Supply of assorted pipes, consumables, manpower, machineries, tools & tackles for carrying out all mechanical works of underground/aboveground piping including fabrication, welding, nondestructive testing of welds, weld repairs/ retesting, cleaning/ flushing, pre-hydrotesting & hydrostatic testing, dewatering, functional testing, cutting of mainline and bevelling (if required), tie-in of valve assembly, including radiography of tie-in joints, corrosion coating (by heat shrink sleeves) for burried piping and external painting for burried fittings by high build epoxy of min. 600 micron of R-95 or equivalent as required, obtaining all statutory clearances, approvals and permissions for the works (wherever required), excavation and filling in all types of soils including soft/ hard rock for installation of piping, painting, finishing, clean-up and restoration of site; preparation of as-built drawings, documents and project records and performing all works as per drawings, specifications, other provisions of Contract document and instructions of Engineer-in-charge.

10'' Tap-off Point

8'' Tap-off Point

6'' Tap-off Point

4'' Tap-off Point

Notes: 1. This work is exclusive of all works associated with main pipeline covered at elsewhere in SOR (Sl.no.1). 2. All others works pertaining to Tap-off (Instrumentation works) (if any) shall be as per rates indicated elsewhere in the tender document. 3. Work is inclusive of receiving, taking over, loading & unloading of company supplied material and return of surplus material to Company's designated stockyard/store. 4.Valve Pit and its upper slab for under ground Tap-off Station shall be payable through separate item rates mentioned elsewhere in the SOR. 5. Incase of bought-out items/ materials, supply of Valves, Assorted Pipe, fittings & Flanges,IJ, instrumentation work...etc shall be paid as per item rates mentioned elsewhere in the SOR. Fabrication of Tap-off point, erection, Testing & commissioing are included in above item rates, hence contractor have to quote accordingly. 6. Qty of tapp off points is tentative and may differ as per site requirement. 7. Qty for tapp-off point mentioned above is excluding quantities mentioned in SV station and for separate locations than SV station. (Refer relevant drawings for Tap-off Station enclosed with tender document for ascertaining quantum of mechanical work associated with Tap-off Station).

CROSSING (by HDD Method)

Complete work for installation of carrier pipeline (between the ROW limits as per approved drawing) by HDD method including "Receiving and taking over" owner supplied three layer PE coated line pipes from Owner's designated place to issue/ dump site(s) and transportation to Contractor's stock yard/ work shop/ work site including all handling, loading, unloading, aligning etc. supply of all Contractor supplied material including consumables, manpower, equipment, other resources to work site(s) and aquiring the required land for storage., Execution of, but not limited to, following works in accordance with specifications and instruction of Engineer-in-charge and as per all provision of Contract Document.

Complete work for installation of carrier pipeline (between the ROW limits as per approved drawing) by HDD method including "Receiving and taking over" owner supplied three layer PE coated line pipes from Owner's designated place to issue/ dump site(s) and transportation to Contractor's stock yard/ work shop/ work site including all handling, loading, unloading, aligning etc. supply of all Contractor supplied material including consumables, manpower, equipment, other resources to work site(s) and aquiring the required land for storage., Execution of, but not limited to, following works in accordance with specifications and instruction of Engineer-in-charge and as per all provision of Contract Document.

Pre-construction survey, necessary cover required over the carrier pipeline from lowest bed level of the stipulated water crossing to be obtained from concerned authority, bed strata data including design & detail engineering and making of crossing drawing for getting their approval from concerned Authority/ Engineer-in-charge, getting work permit/ NOC for water crossings as well as utility crossings (if any) encountered during water crossing prior to start the execution of work. getting work permit/ NOC for water crossings as well as utility crossings (if any) encountered during water crossing prior to start the execution of work.; obtaining historical data/ scour depth (for river) from concerned authority, if required, ascertaining under neath soil & strata, necessary cover required over the carrier pipeline from lowest bed level of the stipulated water crossing including design & calculation and detail engineering and making of crossing drawing for getting the approval from concerned Authority/ Engineer-in-charge, getting work permit/ NOC for water crossings as well as utility crossings (if any) encountered during water crossing prior to start the execution of work. For road crossings,pre-construction survey based on site visit, collection of data (if required) from concerned Authority including design and detail engineering and making of crossing drawings for getting their approval from concerned Authority/ Engineer-in-charge, getting work permit/ NOC for the crossing as well as utility crossings (if any) encountered during crossing prior to start the execution of work.

In case of Water body (i.e River/ Canal/ Distributary, etc.) / Drain / Nala Crossings Drilling to the required depth on the banks and bed including maintenance of drill hole in all types of strata (i.e. soft/hard soil, soft/hard rock including boulder, pebbels / cobbels, etc.), all depth to accommodate the pipeline at all conditions of the waterbody crossings by HDD methods for providing with minimum cover either (i) Minimum 1.5 mtr below the scour level / profile, duly approved/ accepted by concerned authority ( under whose jurisdictions the crossing lies)---- For River/ Distributary/ Canal including with Rocky bed or (ii) Minimum 2.5 mtr below the scour level / profile, duly approved/ accepted by concerned authority ( under whose jurisdictions the crossing lies)---- For River/ Distributary/ Canal without Rocky bed. or (iii) Minimum 4.5 mtr below the lowest bed level / profile (if scour level/ profile is not known), duly approved/ accepted by concerned authority ( under whose jurisdictions the crossing lies)---- For River/ Distributary/ Canal without Rocky bed. or (iv) Minimum 1.5 m below the lowest bed level / profile, duly approved/ accepted by concerned authority ( under whose jurisdictions the crossing lies)---- For Waterbodies (other than River/ Distributary/ Canal) / drain/ nala crossings. and (v) In addition to point (i), (ii) & (iii), In case of multiple combined X-ing i.e.River/ Distributary/ Canal alongwith road/ drain/ nala/ other type of water bodies, minimum cover requirement as per specification/ concerned authority for each type of crossing (x-ing) are also to be fulfilled & maintained.

In case of Road (NH/ SH/ MDR) / Rail crossing, drilling to required depth from top of road including maintenance of drill hole in all types of Strata (i.e; soft/hard soil, soft/hard rock including boulder, pebbels / cobbels etc), all depth to accommodate the pipeline at all conditions encountered during road crossing by approved HDD methods for providing minimum cover specified in code/ specification or the actual depth as decided by concerned authority, whichever is more.

Laying of the carrier pipeline (for both water body and elevated road / rail / structure crossing) by the approved HDD method across the crossing including, strings preparation of carrier , welding, testing, 100% radiography by x-ray, welding repair and retest, coating of field joints with special type Dirax Heat Shrink Sleeve or equivalent (including supply of coating material) and repair of pipeline coating with special PERP-80 repair patch or equivalent material (including supply of repair patch) as per specification, pre-hydrotest of complete strings made for crossing as per specification etc.

Backfilling of the ditch/ trench including restoration and clean-up of area, disposal of drilling fluid & waste etc. to the satisfaction of Engineer-in-charge and /or as directed by Concerned Authority.

Gauging (pre & post installation), Pigging, Cleaning for Post installation hydrotest and carrying out further Post installation hydrotest, dewatering and tie-in with pipeline at either banks or other adjusant pipeline section maintaining minimum pipeline cover 1.0 to 1.5 meter etc. all other works including pigging, Cleaning, final hydrotesting etc. alongwith mainline works(as mentioned above) required as per specifications, codes, approved drawings, calculations, methods and as directed by Engineer-in-charge and provision of contract document, getting NOC from all concerned authority of the facillities crossed. However payment for the Gauging and Post installation hydrotest shall be made as separate items mention else where in the SOR

Details of Crossings

Any type of Crossing viz. Unlined Canal / Distributary / Canal / Drain / River / Nala / NH / SH / MDR / RAIL etc. crossings for carrier pipeline of size 250 NB x 6.4mm Thk. of API 5L Grade X-42/46/52/56/60

Any type of Crossing viz. Unlined Canal / Distributary / Canal / Drain / River / Nala / NH / SH / MDR / RAIL etc. crossings for carrier pipeline of size 200 NB x 6.4mm Thk. of API 5L Grade X-42/46/52/56/60.

Any type of Crossing viz. Unlined Canal / Distributary / Canal / Drain / River / Nala/ NH / SH / MDR / RAIL etc. crossings for carrier pipeline of size 150 NB x 6.4mm Thk. of API 5L Grade X-42/46/52

Any type of Crossing viz. Crossing of Unlined Canal / Distributary / Canal / Drain / River / Nala / NH / SH / MDR / RAIL etc. crossings for carrier pipeline of size 100 NB x 6.4mm Thk. of API 5L Grade X-42/46/52

(i) Quantity against the above crossings items indicated are tentative and for multiple crossings at different locations as per requirement at site and EIC's decision in this regard shall be final and binding to the contractor.

(ii) Crossing width may vary as per site condition. Tenderer are advised to visit the site for actual assessment of extent of crossing and to access the maximum extent of cover which may have to be provided. Actual string length for HDD shall be as per design calculations so that pipe is not under stress as permitted by codes/ specifications. Final length of string shall be decided after decision of minimum cover requirement by concerned Authority/ Engineer-in-charge.

(iii).Payment for the length of final tied-in carrier pipeline string are inclusive in the above item rate and no separate payment shall be made under other item mentioned elsewhere.

(iv) The Contractor has to quote on running meter basis for X-ing. No extra payment of any type shall be made against this item.

(v) Length of the individual crossing may increase* or decrease depending upon site condition/requirement , accordingly HDD rig capacity may increase (w.r.t. rig capacity as mentined in tender document , if any ) and contractor shall deploy the same as per decision of EIC without any extra compensation. (*) - For Individual 10 " NB Pipeline crossing : Single Shot of maximum length upto 250 mtrs. - For Individual 8 " NB Pipeline crossing : Single Shot of maximum length upto 420 mtrs. - For Individual 6 " NB Pipeline crossing : Single Shot of maximum length upto 600 mtrs. - For Individual 4 " NB Pipeline crossing : Single Shot of maximum length upto 750 mtrs.

(vi).For river crossings Geo-technical investigation , bore log data ,hydrological and hydrographical survey of crossings, as required shall be carriedout by the successful bidder and submit the data/report for the same for OWNER / MECON for Approval . Contractor shall submit design calculation and all construction (profile) drawings in line with approved survey data for OWNER / MECON for approval. Work shall start only after approval of the above. However MECON/OWNER shall not be held responsible for the change of underground/ bed strata if found to be variable. Contractor may ascertain the bore hole data by taking random samples,obtain historical data/ scour depth (in case of river/ distributary) from concerned authority ascertaining under neath type of soil / rock in bed strata, necessary cover required over the carrier pipeline from lowest bed level of the stipulated water crossing if they feel the necessity.

RAIL/ NH / SH / MDR (CASED)

Crossing with Casing Pipe by Boring

Complete work of the Road [National Highway (NH) / State Highway (SH) / Major District Road (MDR)] / Rail crossing (between the limits as defined in approved drawings) excluding supply of casing pipe bare (for 10", 8'', 6" & 4" NB carrier Pipeline) including handling, loading, transportation, unloading to Contractor's own stock yard/ work site.

Pre-construction survey and making of crossing drawing based on site visit and getting their approval from concerned Authority/ Engineer-in-charge prior to start the execution of work.

Strings preparation of carrier pipes, welding, testing, 100 % radiography by X-ray, welding repair and retest, coating of field joints with Heat Shrink Sleeve or equivalent (including supply of coating material) and repair of pipeline coating with repair patch or equivalent material (including supply of repair patch) as per specification, pre-hydrotest of complete strings made for crossing etc.

Preparation of required length of carrier pipeline welded string including all other works as mentioned in item no. 1.0 above and as per specification/ drawings. Insertion of carrier pipe in casing pipe after above ground pretesting at specified test pressure including installation of casing insulators and Zn ribbon anode as per approved design calculation, specification/ drawings. Insatllation of vent and drain assembly, fixing of end seals, backfilling and restoration as original of the facilities crossed.

Installation of casing pipe by jacking boring / augur boring for cased crossings including open cut for adjacent service road, canal, minor nature of water channel, utility line crossing etc. (if any) wherever required for all depth in all type of under ground strata (including soft/hard soil and all type of rock ) and terrrain for carrier pipe insertion. All other Contractor supplied materials like casing insulators, Zinc Ribbon Anodes and casing end seals as per enclosed specification/ drawings materials for casing vents and drain assembly etc. including supply of all other materials, equipments, consumables, manpower, welding including visual inspection of all weld joints.

Preparation of required length of carrier pipeline welded string including all other works as mentioned in SOR Sl. No. 1.1 above and as per specification/ drawings. Insertion of carrier pipe in casing pipe after above ground pretesting at specified test pressure including installation of casing insulators and Zn ribbon anode as per approved design calculation, specification/ drawings.Installation of vent and drain assembly, fixing of end seals, backfilling and restoration as original of the facilities crossed.

Backfilling of the ditch/ trench including restoration and cleanup of area, disposal of debrish/ extra earth, & waste etc to the satisfaction of Engineer-in-charge and/or as directed by concerned Authority.

Gauging (pre & post installation), Pigging, Cleaning for Post installation hydrotest and carrying out further Post installation hydrotest, dewatering and tie-in with pipeline with adjusant pipeline section maintaining minimum pipeline cover 1.0 to 1.5 meter etc. all other works including pigging, Cleaning, final hydrotesting etc. alongwith mainline works(as mentioned above) required as per specifications, codes, approved drawings, calculations, methods and as directed by Engineer-in-charge and provision of contract document, getting NOC from all concerned authority of the facillities crossed. However payment for the Gauging and Post installation hydrotest shall be made as separate items mention else where in the SOR.

Tie-in with pipeline at either banks etc.

Details of X-ings

By Jacking/ Boring of Casing Pipe - 16" (406.4 mm) OD, 6.0 mm wall thk. (for 10" NB pipeline)

By Open Cut of Casing Pipe - 16" (406.4 mm) OD, 6.0 mm wall thk. (for 10" NB pipeline)

By Jacking/ Boring of Casing Pipe - 14" (355.6 mm) OD, 5.0 mm wall thk. (for 8" NB pipeline)

By Open Cut of Casing Pipe - 14" (355.6 mm) OD, 5.0 mm wall thk. (for 8" NB pipeline)

By Jacking/ Boring of Casing Pipe - 12" (323.9 mm) OD, 5.0 mm wall thk. (for 6" NB pipeline)

By Open Cut of Casing Pipe - 12" (323.9 mm) OD, 5.0 mm wall thk. (for 6" NB pipeline)

By Jacking/ Boring of Casing Pipe - 10" (273.0 mm) OD, 5.0 mm wall thk. (for 4" NB pipeline)

By Open Cut of Casing Pipe - 10" (273.0 mm) OD, 5.0 mm wall thk. (for 4" NB pipeline)

(i) Actual length & cover from top of casing pipe may vary depending upon site conditions, approved drawings, specification etc. and / or as decided by concerned Authority / Engineer-in-charge.

(ii) Payment for the length carrier pipeline string shall be bored casing pipeline length plus two meters. Payment for additional length of carrier pipeline string shall be paid under SOR item code.: A00100 (including its notes )

(iii) Quantity against SOR items for cased crossings indicated above are tentative. The quantity indicated against each SOR item are not for any single crossings. This shall be as per requirement at site for crossing at different & multiple locations. In this regard and crossing methodology, decision of EIC shall be final and binding to the contractor.

(iv) Supply of casing pipe shall be paid as per relevent SOR item.

Pipe Laying using Manual/ Machine Moiling technique (with Casing) for Carrier pipe

Survey of under ground utilities, execution of the work as per specification, including excavation of pits moling with the hole size not exceeding 20% of the pipe dia, jointing and insertion of carrier pipe with casing, testing & commissioning and restoration of the pits to original condition, submission of As-Built Graph as per specifications and the instruction of Engineer-in-charge.

Laying of 10" (273.0 mm) OD, 6.4mm wall thk of API 5L Grade X-42/46/52/56/60 carrier pipe (in Casing Pipe - 16" (406.4 mm) OD, 6.0 mm wall thk)

Laying of 8" (219.1 mm) OD, 6.4mm wall thk of API 5L Grade X-42/46/52/56/60 carrier pipe (in Casing Pipe - 14" (355.6 mm) OD, 5.0mm wall thk)

Laying of 6" (168.3 mm) OD, 6.4mm wall thk of API 5L Grade X-42/46/52 carrier pipe (in Casing Pipe - 12" (323.9 mm) OD, 5.6 mm wall thk)

Laying of 4" (114.3 mm) OD, 6.4mm wall thk of API 5L Grade X-42/46/52 carrier pipe (in Casing Pipe - 10" (273 mm) OD, 5.0 mm wall thk)

(i) Actual length & cover from top of casing pipe may vary depending upon site conditions, approved drawings, specification etc. and / or as decided by concerned Authority / Engineer-in-charge.

(ii) Payment for the length carrier pipeline string shall be moiled casing pipeline length plus two meters. Payment for additional length of carrier pipeline string shall be paid under SOR item code.: A00100 (including its notes )

(iii) Supply of casing pipe shall be paid as per relevent SOR item

(iv) Quantity against SOR items for moiling ( with casing) indicated above are tentative. The quantity indicated against each SOR item are not for any single location. This shall be as per requirement at site for moiling with casing at different & multiple locations. In this regard and moiling with casing methodology, decision of EIC shall be final and binding to the contractor.

Supply & Coating of Casing Pipe

Complete work of supply of carbon steel pipes required for crossing, including all taxes, duties, transportation and inspection charges but not limited to the following items in accordance with relevant specifications, scope of work, drawings and instructions of EIC as per all provision of contract document. Handling, loading, transportation & unloading etc. to contractor's own stock yard / worksite(s) is also included in contractor's scope.

Supply of Casing Pipe - size 16" (406.4 mm) OD, 6.0 mm wall thk. of material API 5L Gr. B / IS : 3589 or equivalent ERW Pipe (for 10" NB pipeline).

All works related to coating of Casing pipe- 16" (406.4 mm) OD, 6.0 mm wall thk. With coal tar epoxy coating of minimum 600 microns after proper cleaning) including supply of caoting material, consumables etc

Supply of Casing Pipe - size 14" (355.6 mm) OD, 5.0 mm wall thk. of material API 5L Gr. B / IS : 3589 or equivalent ERW Pipe (for 8" NB pipeline).

All works related to coating of Casing pipe- 14" (355.6 mm) OD, 5.0 mm wall thk. With coal tar epoxy coating of minimum 600 microns after proper cleaning) including supply of caoting material, consumables etc

Supply of Casing Pipe - size 12" (323.9 mm) OD, 5.6 mm wall thk. of material API 5L Gr. B / IS : 3589 or equivalent ERW Pipe (for 6" NB pipeline).

All works related to coating of Casing pipe- 12" (323.9 mm) OD, 5.6 mm wall thk. With coal tar epoxy coating of minimum 600 microns after proper cleaning) including supply of caoting material, consumables etc

Supply of Casing Pipe - size 10" (273.0 mm) OD, 5.0 mm wall thk. of material API 5L Gr. B / IS : 3589 or equivalent ERW Pipe (for 4" NB pipeline)

All works related to coating of Casing pipe- 10" (273.0 mm) OD, 5.0 mm wall thk. With coal tar epoxy coating of minimum 600 microns after proper cleaning) including supply of caoting material, consumables etc

Coating of Bare pipes supplied as free issue with Cold tape /equvivalent as approved by client /Consultant

Excavation for pipe top cover beyond 1.5m depth in case of crossing of utilities/ drain/ culverts etc. through open cut upto the following depth (including restoration of the damaged area to its original condition and satisfaction of the Engineer-in-charge / concerned authorities) .The other activities are as per SOR item code.: A00100 (including its notes).

Deeper than 1.5 m & upto 2.5 m below existing level (for 250 mm NB Pipeline)

Deeper than 2.5 m & upto 4.5 m below existing level (for 250 mm NB Pipeline)

Deeper than 1.5 m & upto 2.5 m below existing level (for 200 mm NB Pipeline)

Deeper than 2.5 m & upto 4.5 m below existing level (for 200 mm NB Pipeline)

Deeper than 1.5 m & upto 2.5 m below existing level (for 150 mm NB Pipeline)

Deeper than 2.5 m & upto 4.5 m below existing level (for 150 mm NB Pipeline)

Deeper than 1.5 m & upto 2.5 m below existing level (for 100 mm NB Pipeline)

Deeper than 2.5 m & upto 4.5 m below existing level (for 100 mm NB Pipeline)

(i) Quantities indicated above are tentative and shall be carried out at different & multiple locations.

(ii) Prior permission from EIC is required before execution of above item.

(iii) Other mainline laying activities shall be paid as per SOR item code.: A00100 (including its notes ) mentioned elsewhere in the SOR. Bidder have to quote accordingly.

REPAIR OF DEFECT IN PIPES (NOT ATTRIBUTED TO CONTRACTOR)

Repair of defects on Owner supplied linepipes of all grades and wall thickness as specified in following items, noted and recorded at the time of "receiving and taking over" by Contractor in the presence of Engineer-in-charge.

Cutting and rebevelling for dents in bevels exceeding 3 mm in depth for pipe sizes:

Specified OD, mm

Jack out of dents in bevels ranging between 1 mm and 3 mm in depth for pipe sizes:

Note : Quantity indicated above is tentative and may increase/decrease or delete as per site requirement.

REPAIR OF COATING DEFECTS (NOT ATTRIBUTED TO CONTRACTOR)

Repair of Holiday in Coating (Noted and recorded at the time of "receiving and taking over")

Supply of all coating repair materials as per requirements of specification to be compatible with line pipe coating material, supply of all consumables, utilities, equipments and all manpower required, pipe cleaning and surface preparation, repairing of coating defects (resulting in holiday) and testing including all handling, transportation, etc. for line pipes, performing all works necessary for the completion of the works stirctly in accordance with relevant specification and instructions of Engineer-In-Charge. This rate shall be applicable per sq. cm of the exposed steel area exposed steel area.

Supply, fabrication and installation of all types of permanent markers along the route including all associated civil works such as excavation in all types of soil, construction in all types of soil, construction of pedestals and grouting with concrete, clearing, supply and application of approved colour and quality of primer and paint, stencil letter cutting for numbers, direction, change etc., restoration of area to original condition and performing all works as per drawing, specification and instruction of engineer-in-charge.

Note: Qty of above markers are tentative and may increase or decrease as per site situation. Contractor have to take prior approval from EIC before fabrication or order placement.

Pipeline RCC boundary / route marker as per drawing

Pipeline warning markers with post & foundations

Pipeline direction marker with post & foundations

Pipeline KM with post & foundations

Navigable Waterway Markers

Note: Qty of above markers are tentative and may increase or decrease as per site situation. Contractor have to take prior approval from EIC before fabrication or order placement.

LEAK / BURST (ATTRIBUTABLE TO OWNER)

All works for locating leak / burst in Company's supplied material only (occurred during hydro-static testing) including necessary repairing/replacing defective pipe lengths including cutting and out and removing the defective pipe, pre-testing and welding of replacement pipe, NDT of welds, repair and retesting of defective welds, coating/painting of replacement pipe, pretesting the replacement pipe into mainline/branch line, coating/painting of welding joints, cleanup, retesting including cost of all labour materials, consumables and performing all works in accordance with the provisions of the Contract document and as directed by Owner/ Engineer-in-charge (EIC)

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

(i)This rate is applicable for manufacturing defects in Owner supplied material only.

(ii) Leak detection, its rectification and successfully re-hydrotesting shall be carried out as per approved procedure by Contractor with a view that completion of all activity for successful hydrotesting is not inordinalely extended which will hamper the overall project schedule.

PRE-COMMISSIONING & ASSISTANCE IN COMMISSIONING OF ENTIRE UNDERGROUND PIPELINE LENGTH AND STATIONS

Pre-commissioning activities and pre-commissioning checks to the specified acceptance criteria, making the entire pipeline system ready for commissioning, providing assistance during the complete duration of commissioning operations, supply of all equipment, manpower, consumables (including pigs and required quantity of nitrogen for valve operations) materials for all temporary works and performing all associated works, complete as per the relevant specifications, other provisions of Contract document and instructions of Engineer-in-Charge.

Swabbing of Pipeline section

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

Notes:- i) Above quantities for various pipelines sections at different locations within the GA.. ii) For swabbing, minimum twenty (20) runs (of combination of low density and high density Pigs) shall be carried out till acceptance of the swabbing criteria as per specification, whichever is earlier.

Complete work of carrying out DRYING of the underground pipeline section length by purging of nitrogen or by blowing of dehumidified compressed air till acceptance of Owner/PMC and make ready for Commissioning of pipeline section. This works includes supply of manpower, equipments & consumables (nitrogen reqiured for purging etc.), materials for all temporary works and performing all associated works, complete as per the relevant specifications, other provisions of Contract document and instructions of Engineer-in-Charge.

Drying by continuous purging of nitrogen / blowing of dehumidified compressed air

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

Note:The quantities mentioned above for various pipeline sections at different locations. At the time of execution except above methodology, If other methodology of drying are required as per site condition,the decision of EIC shall be final and binding to the contractor to carry out the decided drying methodology. Payment for the same shall be made to contractor as per provision of contract.

Commissioning assistance during commissioning for underground pipeline length and stations including supply of manpower, equipments, tools & tackles, required consumables (nitrogen reqiured for purging etc.), materials for all temporary works and performing all associated works, complete as per the relevant specifications, other provisions of Contract document and instructions of Engineer-in-Charge.

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

Note:-The quantities mentioned above for various pipeline sections at different locations.

IDLE TIME PRESERVATION OF PIPELINE

Preservation of pipeline sections and associated facilities (in event of delay in ROU acquisition, comissioning, other unforeseen reasons) including supply of nitrogen, all consumables, all equipment, man-power, etc. complete as per the requirements of specifications, other provisions of Contract document and instructions of Engineer-in-charge.

By filling and pressurizing with nitrogen to a pressure of 2 bar(g) for a period of one month.

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

For every additional period of one month or part thereof

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

Note:- i) The quantities mentioned above for various pipeline sections at different locations. ii) All accessrious ie;Two nos. of dished end caps and two nos tappings of 3/4 inches,PG to be considered per section and rate for the same shall be quoted by bidder under this item. iii) If month is partially complete, payment shall be made on prorata basis.

DIGITIZATION OF RADIOGRAPHY FILMS:

Carrying out digitization of all radiographic films (mainline and terminal piping) in the form of digital images (which can then be archived safely for long life and electronic retrieval) complying to all the legal local rules, codes and international standards.Submission of digital images of radiographic film along with compatible software in 6 sets of CD/DVD/Pendrive for electronic viewing /retreival.

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

VIDEOGRAPHY & PHOTOGRAPHY

Carrying out the videography & Photography of the each construction activities for all the pipeline sections.

Videography & photography of the entire route prior to construction activities i.e. pipeline route, location of various stations, Tap-off Point, all crossing like road / railways, river, etc.

Videography & photography during construction activities of Mainline Works i.e. Stringing, Welding, Radiography, Joint Coating, Lowering, Backfilling, etc. performing all works as per specification of EIC and other provision of contract document.

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

GROUND PENETRATING RADAR

Carrying out subsurface utility survey along the proposed pipeline route and/ or as specified by Engineer-In-Charge for provided corridor ( 2-5 meter) using Ground Penetrating Radar (GPR) for depth upto 5m below the existing ground level to locate and identify all existing underground utilities/buried objects including but not limited to pipelines, sewers, conduits, cables, drains, manholes, appurtenances etc in the proposed corridor along with location, DGPS coordinates, depth, shape and dimensional details of utilities. Four (4) Copies of Report and Drawings incorporating all collected datas shall be submitted as per scope of work and direction of the Engineer-in-charge. Scale of Drawing shall be Planimetry (X Axis 1:1000, Y Axis 1:100), Longitudinal Section (Z Axis 1:100) and Transverse Section at critical location.

1.Survey Agency for execution of GPR Survey Work to be engaged by the Contractor shall be submitted for approval of OWNER/MECON prior to start of work.

2. GPR Work shall be carried in presence of Contractor's Representative.

HOT TAPPING WORKS

Arranging the approved specialised agency alongwith hot tapping machine with all its accessories, cuting tool etc. for hot tapping works, obtaining all permissions/ clearances/ permits from Owner/ concerned authorities, submitting all procedures for approval & obtaining approval thereon prior to start of works, carrying out hot tapping works including installation of split tees / weldolet & full bore ball valve with support on existing pipeline, supply of all materials i.e. SPLIT TEES ,weldolet, flange, pipes, full bore ball valves as per Data sheets & Techincal specifications

Consumables for welding & testing requirements, tools, tackles, skilled and unskilled manpower, safety and fire fighting system including fire tenders (if required ) etc. hydrotesting the installed fitting, carryingout radiography & all NDT, providing valve pit at tap-off point as per drawing, carrying out all works as per the requirements of specification, other provisions of contract document and instructions of Engineer-in-charge. Final restoration of area to its original to the entire satisfaction of Engineer-in-charge.

Note:- All works associated with installation of valve pit and fencing (if required) including supply of all materials & manpower as detailed in piping drawings shall be paid as per rates covered elsewhere in the tender document and shall not be included in the lumpsum price quoted herein.

Run Pipe NB (Inches) x Branch Pipe NB (Inches)

8" x 6" (With Split Tee) (300#)

8" x 4" (With Split Tee) (300#)

6" x 4" (With Split Tee) (300#)

4" x 4" (With Split Tee) (300#)

NOTE- Quantity mentioned above is for the various locations within the GA and may increase/decrease or not to be executed based on site requirement.

HOT WORK

Complete shutdown work required for interconnection with existing underground pipelines including fabrication of piping section having the portion of run pipes of 10"/8''/6"/4" NB, Tees , Elbow, Bend etc with branch pipe of 10"/8"/6"/4"/2 NB size as instructed by EIC(total fabricated length shall not be increasing by 6 mtrs) , welding , NDT, Coating , cleaning with Air , Excavation of Pit , back filling, restoration of Pit , removal of coating from line pipes including run pipe/s , re-coating etc for hooking up of 10"/8"/6"/4"/2" NB line pipe including supply of required quantity of nitrogen for purging till acceptance of PMC/Owner and used for other activities for main line / Run pipe of 10"/8''/6"/4" NB as per instruction of Engineer In Charge . Other wokrs which are required additionally will be paid as per seperate SOR mentioned else where.

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

NOTE- 1. Quantity mentioned above is for the various locations within the GA and may increase/decrease or not to be executed based on site requirement. 2. Above item covers all work required to be complete the hot work including supply of nitrogen as per requirement.

TRIAL PITS

Excavation of trial pits on pipeline route (min Size 1.5 Mtr x 1.0 Mtr.) or any other Location as per instruction of engineer incharge in all kinds of underground strata up to existing laid pipeline without damaging pipe coating.Barricating the trial pit area including application of warning tape /warning sign around the trial pit till the necessary checking & backfilling of same as per direction of Engineer Incharge.Cleaning of excavated pipe & other underground facilities including supply of all materials (except Owner supplied materials), consumables, equipment, labour, etc. for carryout the reffered work as per directions of the Engineer-in-charge.

NOTE:- Quantity mentioned above is for the various locations within the GA and may increase/decrease or not to be executed based on site requirement.

Gauging (Applicable during carrying out main steel pipeline hydrostatic test, Pre & Post installation hydrostatic test.)

As per specification and procedure approved by Engineer–in–charge (EIC)/ RCM.

Specified dia Thk (mm) Material Coating Type Length of each pipe (mm) NB

250 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

200 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

150 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

100 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

NOTE- (i) The quantities mentioned against the above SOR items are tentative and may vary depening upon the site condition during execution stage. (ii) The total quantities mentioned against the above SOR items are applicable for main steel pipeline and multiple/various crossings at different locations. (iii) Payment for above item shall be made only for the certified executed length of pipeline by Engineer–in–charge (EIC)/ RCM. (iv) The requirement of gauging of main steel pipeline, prehydrotest & after pulling of HDD section/ crossing by open-cut (Conventional) method/ cased crossings/ moiling with casing, if feasible as per site condition/ geomatry of pipeline section shall be carried out as per MECON specification / OISD / PNGRB regulation and same shall be decided & approved by Engineer–in–charge (EIC)/ RCM.

Post Installation of Hydrostatic testing

Carrying out cleaning, gauging, pigging and post installation hydrostatic testing of complete pipeline section laid by HDD method as approved by EIC/RCM to specified pressures (i.e. 1.5 times of the design pressure) for 24 hours holding period; providing all equipment, pumps, test headers, fittings, instruments, dead weight tester, pressure recorder, tempearature recorder , pressure & temperature gauge etc., and services, supervision, labour, consumables, water including supply of corrosion inhibitor, air, etc. as required for successful completion of hydrotesting of pipeline to acceptance criteria as per specifications, codes, approved drawings, calculations, methods and as directed by Engineer-in-charge and provision of contract document. Complete dewatering and swabbing of the pipeline as per specification and to the entire satisfaction of the EIC/RCM.

As per specification and procedure approved by Engineer–in–charge (EIC)/ RCM.

250 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

200 6.4 API 5L Gr. X-42/46/52/56/60 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

150 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

100 6.4 API 5L Gr. X-42/46/52 3 Layer PE Coating Double random (Externally) (approx. 11.5 m to 12.5 m)

NOTE- (i) The quantities mentioned against the above SOR items are tentative and may vary depening upon the site condition during execution stage. (ii) The total quantities mentioned against the above SOR items are applicable for main steel pipeline laid through HDD method and for multiple/various crossings at different locations. (iii) Payment for above item shall be made only for the certified executed length of pipeline by Engineer–in–charge (EIC)/ RCM. (iv) The requirement of Post Installation of Hydrostatic testing of main steel pipeline laid through HDD method and after pulling of HDD section/ crossing by open-cut (Conventional) method/ cased crossings/ moiling with casing, if feasible as per site condition/ geomatry of pipeline section shall be carried out as per MECON specification / OISD / PNGRB regulation and same shall be decided & approved by Engineer–in–charge (EIC)/ RCM.

i) The quantities mentioned against the above SOR items are tentative and may vary depening upon the site condition during excecution stage.

ii) Payment for Gauging activity mentioned above shall be made under separate SOR item mentioned elsewhere in this SOR.

iii)Quantity indicated above against each item is tentative and for multiple crossings . It may increase/decrease as per site condition and approved survey details.

Pipeline Laying Liasioning & Co-odrination (including utility crossing) and obtaining permission / NOC from the statuatory / concerned authorities. Assistance in ROU / Pipeline Route Alignment Corridor opening & closing and their maintainence/ management.

Submitting request for (after obtaining the letter from client) permission , follow up , assisting in site inspections / route suevey / site report making/making site inspection drawings , submitting at designated offices , resubmission after correction , modification if required , soft and hard copy in nos. as required /if required in sizes , and collecting permission from the statuatory authorities including NHAI , PWD , Railways , Irrigation , Forest , Municipal Corporation, District administration, River Authority,SEZ etc. Obtaining work permits /NOC from various statutory authorities having jurisdiction before execution of the work and complying with all stipulations /conditions/recommendations of the said authorities. Only statutory fees shall be paid by the owner. Assistance in required length and width/restricted width of ROU opening & closing and their maintainence/ management both side of the crossings.

For 10" NB Line

For 8" NB Line

For 6" NB Line

For 4" NB Line

NOTE- (i) The quantities mentioned against the above SOR items are tentative and may vary depening upon the site condition during execution stage. (ii) The total quantities mentioned against the above SOR items are applicable for the works carried out as mentioned above for laid, tested & commissioned or preserved with nitrogen main steel pipeline section and quantity mentioned against each SOR item is for multiple/various crossings at different locations within the GA. (iii) 90% payment for the above item shall be made only after the certified length of executed, tested & commissioned or preserved with nitrogen main steel pipeline section by Engineer–in–charge (EIC)/ RCM. Rest 10% payment will be made after acceptance of the system by Owner/PMC and after closure of contract.

Note for all above SOR Items code Nos. A00100 to A003000 :- (i) Quantities mentioned against all above SOR items are estimated & tentative and may vary up to any extent as per site condition and/or as per instruction of EIC. (ii) If certain documents, drawings, datasheets, specifications etc. are not included in the bid, the same will be made available to the successfull bidder. While formulating the bid, bidders are requested to quote such items based on the industry practices followed by the similar nature of industries. However procurement & installation of such items will be done as per site requirement after due approval of EIC. (iii) Laying/ installation of pipeline along with associated works mentioned in above SOR items are also to be utilized and carried out for various consumer connectivities/ extension of pipeline … etc with in the Geographical Area (GA). (iv) In the above SOR items & scope of works, incase of any conflict in requirement among PJS, Technical Specification, tender documents, drawings, datasheets, latest relevant Codes & Standards, Statutory Regulation, requirement of the local authority, etc., the most stringent requirement shall govern, however decision of EIC in this regard shall be final and binding to the contractor.

TEMPORARY CATHODIC PROTECTION WORKS

Description of Item

Design, detail engineering, Manufacturing, Inspection/FAT (Factory acceptance test), supply, Packing, insurance, transportation to site, storage at site, Handling, Transportation, Loading, installation, testing & commissioning of the temporary Cathodic protection system using Mg (Min 5.0 Kg Each) galvanic anodes to protect the external surface of 10"/ 8"/6"/4" dia x 55.0 km (appox.) long 3LPE Coated pipeline against corrosion for a design life of minimum 2 year or till commissioning of existing PCP system whichever is later in the Geographical Area (GA) of Sonipat, Meerut & Dewas as per standard specification No.- MEC/S/05/E9/016A for temporary cathodic protection system, Scope of work, Data Sheets & tender drawings. Scope shall also include but not limited to the following for completion of jobs:

Soil resistivity Survey & soil/water chemical analysis

Measurement of soil resistivity along the right of way of the main pipeline (At 500mtr Interval at depth of 1.5M, 2.5M & 3.5M) & collection of additional data as per specification for corrosion survey MEC/TS/05/21/016C & applicable NACE standard including preparation of Design, detailed engineering, preparation of design document, preparation of Test station schedule & Bill of Material.

Collection of soil & water samples along ROW at depth of 1M, 2M & 3M at every 5 km interval (Min 03 sample at each location) for its chemical & microbial analysis along the pipeline route as per specification for corrosion survey MEC/TS/05/21/016C & NACE Standard TM0106-2006 for detection of SRB, ARB & Total dissolved H2S etc.

Sacrificial anodes- Pre packed Mg anodes

Prepacked Magnesium anodes for Carrier/Casing Pipe protection (Min 5.0 Kg Each) as per tender specification (1/2/3/4 Nos. of anodes). The total nos. of anodes shall be calculated as per the corrosion survey, soil chemical analysis, total weight and current requirement of the pipeline section. However, Min one anode is to be installed at every one KM with test station.

Supply, laying, termination, Glanding and ferruling TCP-Cables--The Cables shall be annealed high conductivity, stranded copper conductor, 650/1100V grade, XLPE Insulated & PVC Sheathed in new/existing test stations and junction boxes.

1c x 6 mm2 - Anode tail cable - unarmored

1 core x 6 mm2 - Potential Measurement, TLP to pipeline, armoured

1 core x 10 mm2 - current measurement cable & Pipeline to Test station- armoured

1 core x 25 mm2 -Bonding, Earthing, Surge diverter, HT line, etc.

Test Stations

New test stations Normal Size-(Weather Proof with IP-55) as per tender drawings with name plate

New test stations Big Size-(Weather Proof with IP-55) suitable for Polarisation Cells as per tender drawings with name plate

All Cable to pipe connections by Exothermic Process or Pin Brazing for all sizes (Upto 1C x 25mm2) for complete TCP system of whole pipeline.

Solid State type Polarisation cells (3.7 kA @ 30 Cycle) for HT power line crossings (66KV & above).

20 Kg Sacrificial Zinc anodes for HT line crossing, Earthing of block valves on Cathodically Protected portion of pipeline.

Cu-wire mitigator for AC Mitigation encased in low resistance backfill with corrosion inhibitors and braiding (M/s MATCOR make or equivalent) (20 Mtr wire shall be installed on each side of HT crossing, Cables running parallel etc).

Solid state Surge Diverters rating 100 kA (10/350 uS) for Insulating Joints.

HDPE sheet (Non-toxic and Rodent Resistant, 6mm thick & 5000mm wide (1200mmx5)) between the GAIL Gas pipeline and the other CP protected foreign pipelines at the crossing locations for providing electrical isolation.

Supply, installation, testing, commissioning of the complete earthing protection system, earth electrodes/ pit, earth main ring, earthing of electrical equipments, instrument panels, field instruments, process equipments and pipes/ flanges including all associated civil work with all material and labour as per specification and drawings approved by the company.

Earthing Electrodes 65mm dia x 3mtr long & 4.5 mm thick GI pipe for earthing of cathodically unprotected pipeline at consumer station/DRS station/Metering skid and earthing. Total grounding resistance shall be limited to 2-3 Ohm max.

GI Strip (50X6) mm

GI Strip (25X3) mm

Copper Strip (25X3) mm

GI Wire (8mm-Stranded), Cu- wire rope (Min 8 mm dia solid) and all balance earthing material including copper strip (50 mm x 2 mm thick) jumper for flanges etc. as per the specification for all stations.

Monitoring of the TCP system, on monthly basis, till commissioning of the permanent cathodic protection system.

Polarisation coupons (100 mmx 100mm) with Magnetic reed switch as per NACE SP 104 with permanent ref cell.

PIPING & MECHANICAL WORKS

PLANT PIPING FOR UNDERGROUND/ ABOVEGROUND INSTALLATION

Transportation including loading, unloading & handling of all piping items from Owner's and/ or Contractor's storage point to work site/ workshop as applicable, complete work of fabrication, erection, painting, testing of pipes, flanges and fittings and making ready for further Commissioning / Start-up of carbon steel piping of all sizes and ratings including supply of all consumables, equipment, manpower and other resources and execution of, but not limited to, the following works in accordance with relevant specifications & scope of work, drawings, specification and instructions of Engineer-in-charge and as per all provisions of the CONTRACT DOCUMENT.

Fabrication including cutting, edge preparation, inclusive of grinding the edges of pipes, fittings, flanges etc. to match with the matching edges of uneven/different thickness wherever required, welding, attachment of all pipe fittings like elbows, tees, reducers. Supply of nipples, couplings,caps, plugs, gasket, stud bolts, nuts, U Clamps etc. as required for completion of job.

Fixing/ Installation of weldolets, sockolets, flanges, vent and drain point connection etc., including providing stub-in connections, fabricated fittings and reinforcement pads etc., as required.

Erection including prior cleaning, lifting, placing on pipe sleepers and supports, overhead on racks, skids and at all elevations including installation and carrying out connected activities for all types of valves including supply and fixing of gaskets, studs/ bolts, nuts wherever required for all sizes, levelling, aligning, joining of flanges, blind flanges, connecting with equipment, nozzles, strainers, tie-in with existing piping/facilities, etc. tapping for inline instruments like pressure gauges, thermowells, sample connection, etc.

Preparation of final bill of material based on piping GADs.

Preparation of isometric and fabrication drawings.

Carrying out Non-destructive testing as required. NDT for 2'' & above shall be paid as per separate itmes mentioned elsewhere in the SOR.

Surface preparation before application of primer by means of sand blasting including supply of approved quality of sand, manpower, machineries, tools & tackles to achieve required roughness as per specification and as per instruction of Engineer-in-charge.

Painting of entire system (including aboveground all pipes fittings, flanges and accessories) as per specification MEC/S/05/21/07 suitable for corrosive area environment including supply of approved paints and primers, application of primer and paints, indentification lettering/ numbering, colour coding, etc. as specified including rub down & touch up of shop primer or scrapping of shop primer wherever required by COMPANY and providing scafolding for all heights etc.

Cleaning and flushing by water/ compressed air, testing of the systems including hydrostatic, pneumatic and any other type of testing as specified, draining, drying by compressed air/other methods approved by COMPANY.

Precommissioning & making operational all piping system and equipments and provide all necessary assistance in term of supply of man-power, equipment, tools and tackles required amount of nitrogen for purging of entire terminal piping system including equipments etc. to the company during commissioning activities.

Clean-up and restoration of site, preparation of as built drawings, documents and project records; transportation of surplus free issue material to Owner's designated plac(s); completing all works in all respects as per the AFC drawing, specifications, standards and other provisions of Contract and instruction of Engineer-in-charge.

Completion of all such work in all respects as per scope of work and as per drawings, specifications and instructions of the COMPANY and keeping the system ready in all respects for further commissioning and start up.

Hook-up works including making provision for hooking up and carrying out shutdown activities at terminals if necessary.

Complete Carbon Steel Piping Work with painting including all fittings, flanges and supply of all required gaskets, studs bolts & nuts etc. as described under SOR item code.: C00101 (including its notes )

API 5L Gr.B, PSL2 (For 10" NB), STD

API 5L Gr.B, PSL2 (For 8" NB), 7.9

ASTM A106, Gr. B (Charpy), Seamless, BE (For 6" NB), S40

ASTM A106, Gr. B (Charpy), Seamless, BE (For 4" NB), S40

ASTM A106, Gr. B (Charpy), Seamless, BE (For 3" NB), STD

ASTM A106, Gr. B (Charpy), Seamless, BE (For 2" NB), XS

ASTM A106, Gr. B, Seamless, PE (For 1" NB) , XS

ASTM A106, Gr. B, Seamless, PE (For¾" NB), S160

SUPPLY OF ASSORTED PIPE, FITTINGS AND FLANGES

Complete work of supply of pipes, fittings and flanges including all taxes, duties, transportation and inspection charges but not limited to, the following items in accordance with relevant specifications indicated in clause of SCC & scope of work indicated in SCC, drawings, specification and instructions of Engineer-in-charge and as per all provisions of the CONTRACT DOCUMENT.

Handling including lifting, transportation from Contractor Stores to CONTRACTOR's workshop for fabrication and/ or to work site for field fabrication and erection for all piping items supplied by Contractor.

CARBON STEEL PIPES

API 5L Gr.B, PSL2 (For 10" NB), STD

API 5L Gr.B, PSL2 (For 8" NB), 7.9

ASTM A106, Gr. B (Charpy), Seamless, BE (For 6" NB), S40

ASTM A106, Gr. B (Charpy), Seamless, BE (For 4" NB), S40

ASTM A106, Gr. B (Charpy), Seamless, BE (For 3" NB), STD

ASTM A106, Gr. B (Charpy), Seamless, BE (For 2" NB), XS

ASTM A106, Gr. B, Seamless, PE (For 1" NB) , XS

ASTM A106, Gr. B, Seamless, PE (For¾" NB), S160

FLANGES

Weld Neck (B-16.5, A105(Charpy), 125 AARH, RF) [End Thickness to match pipe thickness] , (For 10") ,300#

Weld Neck (B-16.5, A105(Charpy), 125 AARH, RF) [End Thickness to match pipe thickness] , (For 8" ), 300#

Weld Neck (B-16.5, A105(Charpy), 125 AARH, RF) [End Thickness to match pipe thickness], (For 6") ,300#

Weld Neck (B-16.5, A105(Charpy), 125 AARH, RF) [End Thickness to match pipe thickness], (For 4"),300#

Weld Neck (B-16.5, A105(Charpy), 125 AARH, RF) [End Thickness to match pipe thickness], ( For 3"),300#

Weld Neck (B-16.5, A105(Charpy), 125 AARH, RF) [End Thickness to match pipe thickness], (For 2"),300#

Socket Welded (B-16.5, A105, 125 AARH, SW end to B16.11), (For 1"), 300#

Socket Welded (B-16.5, A105, 125 AARH, SW end to B16.11), (For ¾" ), 300#

Blind Flanges (B-16.5, A105 (Charpy), 125 AARH, RF), (For 10") , 300#

Blind Flanges (B-16.5, A105 (Charpy), 125 AARH, RF), (For 8") , 300#

Blind Flanges (B-16.5, A105 (Charpy), 125 AARH, RF), (For 6") , 300#

Blind Flanges (B-16.5, A105 (Charpy), 125 AARH, RF), (For 4"), 300#

Blind Flanges (B-16.5, A105 (Charpy), 125 AARH, RF), ( For 3"), 300#

Blind Flanges (B-16.5, A105 (Charpy), 125 AARH, RF), (For 2"), 300#

Blind Flanges (B-16.5, A105, 125 AARH, RF), (For 1"), 300#

Blind Flanges (B-16.5, A105, 125 AARH, RF), (For ¾" ), 300#

ELBOW

90° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 10", STD)

90° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 8", 7.9)

90° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 6",S40)

90° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 4", S40)

90° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 2", XS)

90° Elbow (ASTM A 105, B-16.11 ) End details ( SW 3000# for 1") , (For 1",XS)

90° Elbow (ASTM A 105, B-16.11 ) End details (SW 6000# for 3/4), (For 3/4",S160)

45° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), (For 10", STD )

45° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), (For 8", 7.9)

45° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), (For 6",S40)

45° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), (For 4", S40)

45° Elbow (A234, Gr. WPB (Charpy), B-16.9, 1.5D), (For 2", XS)

Equal Tee (A234, Gr. WPB (Charpy), B-16.9), (For 10", STD)

Equal Tee (A234, Gr. WPB (Charpy), B-16.9), (For 8", 7.9)

Equal Tee (A234, Gr. WPB (Charpy), B-16.9), (For 6", S40)

Equal Tee (A234, Gr. WPB (Charpy), B-16.9), (For 4", S40)

Equal Tee (A234, Gr. WPB (Charpy), B-16.9), (For 2", XS)

Equal Tee (ASTM A105, B-16.11) (End Details SW, 3000#),(For 1",XS)

Equal Tee (ASTM A105, B-16.11) End Detail SW, 6000#,(For 3/4",S160)

Unequal Tee (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 10" x 8", STD x 7.9 )

Unequal Tee (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 8" x 6", 7.9 x S40 )

Unequal Tee (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 8" x 4", 7.9 x S40 )

Unequal Tee (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW, (For 6" x 4" S40 x S40 )

Unequal Tee (A234, Gr. WPB (Charpy), B-16.9, 1.5D), BW ,(For 4" x 2", S40 x XS )

Uequal Tee (ASTM A105, B-16.11), (For 2" x 1", XS x XS)

Uequal Tee (ASTM A105, B-16.11), (For 1"x3/4", XS x S160)

SOCKOLET

SOCKOLET (A105, B16.11, 6000#) ,4" x ¾"

SOCKOLET (A105, B16.11, 3000#/ 6000#) , 4" x 1"

SOCKOLET (A105, B16.11, 6000#) , 2" x ¾"

BARRED TEE (As per Standard Specification and Data Sheets enclosed)

BARRED TEE (As per Standard Specification and Data Sheets enclosed) , 10" x 4",6.4

BARRED TEE (As per Standard Specification and Data Sheets enclosed) ,8" x 4", 6.4

BARRED TEE (As per Standard Specification and Data Sheets enclosed) ,6" x 4", 6.4

BARRED TEE (As per Standard Specification and Data Sheets enclosed) ,4" x 4", 6.4

INSULATING JOINTS (As per Standard Specification and Data Sheets enclosed)

INSULATING JOINTS (As per Standard Specification and Data Sheets enclosed) , 10" ,300#

INSULATING JOINTS (As per Standard Specification and Data Sheets enclosed) ,8" ,300#

INSULATING JOINTS (As per Standard Specification and Data Sheets enclosed) ,6" ,300#

INSULATING JOINTS (As per Standard Specification and Data Sheets enclosed) ,4" ,300#

INSULATING JOINTS (As per Standard Specification and Data Sheets enclosed) ,2" ,300#

Reducer (A 234 Gr. WPB (Charpy), BW)

Reducer (A 234 Gr. WPB (Charpy), BW),STD x 7.9, 10"x8"

Reducer (A 234 Gr. WPB (Charpy), BW),7.9 x S40, 8"x6"

Reducer (A 234 Gr. WPB (Charpy), BW),7.9 x S40, 8"x4"

Reducer (A 234 Gr. WPB (Charpy), BW),S40 x S40,6"x4"

Reducer (A 234 Gr. WPB (Charpy), BW),S40 x XS, 4"x2"

Reducer (A 234 Gr. WPB (Charpy), BW),S40 x STD., 4"x3"

Reducer (A 234 Gr. WPB (Charpy), BW),STD. x XS, 3" x 2"

Weldolet

Weldolet (ASTM A 105 (Charpy), BW, MSSSP-97),10"x2",STD x XS

Weldolet (ASTM A 105 (Charpy), BW, MSSSP-97),8"x2", 7.9 x XS

Weldolet (ASTM A 105 (Charpy), BW, MSSSP-97),6"x2",S40 x XS

Note: i) All butt welded fittings end shall generally match with connecting pipe wall thickness however in case of misalignment Contractor shall have to do end preparation without any extra cost.

ii) All coupling, nipples etc. as required shall be supplied by contractor but no separate payments shall be made as it is covered under erection rate.

Supply of Valves

Complete work of supply of valves including all taxes,duties,transportation and inspection charges but not limited to ,the following items in accordance with relevant Specifications & relevant Data Sheets indicated in scope of work indicated in SCC, drawings, specification and instructions of EIC and as perall provisions of the CONTRACT DOCUMENT.

Plug Valves

Butt Welded End (As per PMS & Datasheet), 4",300#

Butt Welded End (As per PMS & Datasheet), 2",300#

Socket Welded End (As per PMS & Datasheet), 1",300#

Ball Valves

Fully Welded Body, Butt Welded End, Full Bore (As per PMS & Datasheet),10", 300#

Fully Welded Body, Butt Welded End, Full Bore (As per PMS & Datasheet),8", 300#

Fully Welded Body, Butt Welded End, Full Bore (As per PMS & Datasheet) ,6", 300#

Fully Welded Body, Butt Welded End, Full Bore (As per PMS & Datasheet) ,4", 300#

Fully Welded Body, Butt Welded End, Reduced Bore (As per PMS & Datasheet),4", 300#

Flanged End, Full Bore (As per PMS & Datasheet) ,2", 300#

Butt Welded End, Full Bore (As per PMS & Datasheet) ,2", 300#

Socket Welded End, Full Bore (As per PMS & Datasheet),1", 800#

Socket Welded End, Full Bore (As per PMS & Datasheet) ,¾", 800#

Socket Welded End, Full Bore (As per PMS & Datasheet), 1/2", 800#

ERECTION OF VALVES ( As per P & ID )

Handling including lifting and transportation from COMPANY's warehouse to CONTRACTOR'S Stores and/or work site and installation of all types of valves including assembly of valve accessories, (if any) by bolting, threading or welding, supply and insertion of gaskets, nuts & bolts, nipples, etc. at all elevations of pipe sleepers, supports or overhead on racks, equipments nozzle, skid & painting etc. supply of all consumables, manpower, equipment, etc. for completion of all works as per scope of work and as per drawings, specifications and instructions of Engineer-in-charge including servicing/ cleaning of valve wherever requried.

Flanged/ Welded Valves (Full Bore/ Reduced Bore)

Ball / Plug Valves, 10",300#

Ball / Plug Valves,8",300#

Ball / Plug Valves,6",300#

Ball / Plug Valves,4",300#

Ball / Plug Valves,2",300#

Sockolet Welded Valve

(Ball / Plug / Valves),1", 800#

(Ball / Plug / Valves),¾"", 800#

(Ball / Plug / Valves),1/2", 800#

RADIOGRAPHY

Performance of radiographic inspection by gamma radiation as per scope of work and as per specifications in piping of all types and thickness including providing/hiring of all necessary equipments, supply of all consumables, and whatever else even though not expressely mentioned but required to perform the work as per specifications and instructions of Engineer-in-Charge (full circle re-radiography of the repaired joint and additional radiography necessitated due to poor performance of contractor's welder shall be carried out by the Contractor at his own cost and shall not be paid extra by Company). Radiographs shall be submitted to the Engineer-in-Charge for acceptance, whose decision shall be final and binding.

Radiography by Gamma Rays,10"

Radiography by Gamma Rays,8"

Radiography by Gamma Rays,6"

Radiography by Gamma Rays,4"

Radiography by Gamma Rays,3"

Radiography by Gamma Rays,2"

ERECTION OF SKIDS & OTHER EQUIPMENTS

Handling, including lifting, transportation from Company's stores to Contractor's work-shop for fabrication or/ and to worksite for field fabrication, assembly of parts/ sub-assemblies, erection for all Metering skids/DRS/MRS/Compressors, equipments supplied by company above ground/ underground at all elevation/ depth, fixing of foundation bolts, welding wherever required, aligning, grouting, hooking-up, cleaning and flushing by water draining, drying by compressed air, providing all mountings, ancilliary, enabling works as required and completing in all respect as per drawings, specification and instruction of Engineer-in-charge. Contractor's scope shall include supply of all material and accessories including but not limited to any fixtures, clamps, gasket, nut bolts, finish coat of painting including rub down & touch up of shop primer/ paint scrapping of shop primer/ paint and further their painting after application of primer as per specification, wherever required by Company.

Details of equipment are as under

Details of Equipment

Metering Skids/ MRS/DRS/DCU-cum-DRS Compressors.. ...etc

1) Payment of above ground Piping fabrication works cover in above SOR items shall be paid under SOR item code.: C00101 (including its notes )

2) The quantity mentioned against above SOR item are for multiple equipment having different weight and weight of each eqipment shall be maximum upto 10.0 MT. The each equipment shall be installed at different location within the GA.

FIRE FIGHTING (Portable Extinguishers)

Fire Fighting Equipment

Supply, installation and commissioning of the following fire fighting equipment:

75 kg capacity DCP type (trolley mounted)

10 kg capacity DCP fire extinguisher (trolley mounted)

4.5 kg capacity CO2 fire extinguisher (portable) as per IS:2878

6 Nos. Sand Buckets with stand & canopy

NOTE: 1) The quantities given above against individual items are indicative and shall not be considered to be binding. The quantities may be increased, decreased or deleted at site at the time of actual execution. Procurement shall be done as per actual site condition, approved construction drawings and as per instruction of Engineer-in-charge. The unit rate shall be operated to work out the final payment to the contractor.

2) In each area, quantities given against individual item may be utilise/ used for other consumer in same area.

3) The rates quoted shall be applicable for all underground/ aboveground piping system and associated stations/ terminals.

Note for all above SOR Items code Nos. C00100 to C001600 :- (i) Quantities mentioned against all above SOR items are estimated & tentative and may vary up to any extent as per site condition and/or as per instruction of EIC. (ii) If certain documents, drawings, datasheets, specifications etc. are not included in the bid, the same will be made available to the successfull bidder. While formulating the bid, bidders are requested to quote such items based on the industry practices followed by the similar nature of industries. However procurement & installation of such items will be done as per site requirement after due approval of EIC. (iii) Installation of all underground/ aboveground piping system along with associated works mentioned in above SOR items are also to be utilized and carried out for various consumer connectivities/ extension of existing piping system … etc with in the Geographical Area (GA). (iv) In the above SOR items & scope of works, incase of any conflict in requirement among PJS, Technical Specification, tender documents, drawings, datasheets, latest relevant Codes & Standards, Statutory Regulation, requirement of the local authority, etc., the most stringent requirement shall govern, however decision of EIC in this regard shall be final and binding to the contractor.

CIVIL WORKS

CIV-1 EARTH WORK IN EXCAVATION/ SITE GRADING AND BACKFILLING

Earth work in excavation /site grading in all kinds of soil including soft rock in any plan dimension up to required depth including backfilling of excavated earth at any location in layers of 300mm and compacted up to 95% to its MDD at all heights and depths. Surplus and unserviceable earth shall be disposed up to any lead in all conditions. Soil to be levelled and neatly dressed complete in all respect as per scope of work, detailed construction drawings, technical specifications and direction of the Engineer-in-Charge.

CIV-2 BRICK WORK

Providing and laying brick work with brick class designation M-5.0 of IS:1077 in Cement Mortar 1:4 (1cement : 4 sand) in steps, load bearing structures, drains, or at any other location at all depths & height for all leads including providing required finishes, curing, scaffolding, etc., complete as per specifications and drawings with all bye-works as per direction of the Engineer-in-charge.

Note:- 1.Rate to include cost of all labour, tools, tackles, equipment, hire charges, supply of all materials such as minimum 43 grade cement (OPC), bricks, finishes, bitumen, other minor construction materials, shuttering, staging, masonry work, excavation, PCC M10, plastering with 15 mm thick cement plaster on exposed faces with 1:4 cement mortar( 1 cement : 4 Sand) , painting with bitumen etc. as per requirement with all bye-works and sundry works complete as per drawings. 2. To be read in conjunction with Particular Job Specification.

CIV-3 PLAIN CEMENT CONCRETE

Supplying and laying plain cement concrete of grade M 10 with stone aggregate 40mm down grade (including shuttering if required) in all types of concrete works including levelling courses below foundations, mass concrete works, chambers, cable trench, under floors and any other locations, at all levels and locations (which are not covered as part of composite items) as per drawings, specifications and directions of the Engineer-in-charge.

Note:- 1.Rate to include cost of all labour, tools, tackles, equipment, hire charges, supply of all materials, shuttering in all conditions etc. with all bye works and sundry works. 2. To be read in conjunction with Particular Job Specification.

CIV-4 REINFORCED CEMENT CONCRETE

Providing and laying Reinforced Cement Concrete of grade M-25 with 20mm and down grade crushed stone aggregate in all types of structures like foundations, beam, columns, pedestals, pedestal bases, pipe supports, sleepers, cable trench, RCC retaining wall foundation for boundary wall etc. including excavation, PCC M10 in mud mat, shuttering, construction joints, bitumen painting on surfaces in contact with soil,supplying and fixing MS inserts, finishes etc. at all depths and levels complete as per drawings, specifications and directions of the Engineer-in-charge.

1. Rate to include cost of all labour, tools, tackles, equipment, hire charges, supply of all materials such as minimum 43 grade OPC cement including sulphate resistant cement for sub-structures, inserts, bolts, conduits, bitumen, excavation, PCC M-10 in mud mat, other minor construction materials, shuttering , staging, testing of concrete, curing etc. except reinforcement steel with all bye works and sundry works complete.

2. To be read in conjunction with Particular Job Specification.

CIV-5 REINFORCEMENT STEEL

Supplying and Fabricating and Fixing in position HYSD Steel Reinforcements/ TMT Grade Fe-415/Fe 500D conforming to IS1786-2008 at all levels and positions including the Cost of transportation, Straightening, Cutting, Bending, Cranking, Binding, Welding, Provision of necessary Chairs and Spacers, Preparation of bar bending schedule, getting the same approved by EIC etc., complete as per Drawings and Specifications and including Cost of binding wire, Labour etc., all complete in all respects as per scope of work, detailed construction drawings, technical specifications and direction of Engineer-in-charge. The Chairs and Spacer Bars provided will not be measured for payment.

1. Rate to include cost of all labour, tools, tackles, equipment, hire charges, supply of all materials such as steel Reinforcement, binding wire and other minor construction materials, testing etc. all bye works and sundry works.

2. Chairs, Laps, Spacers, Wastage etc. shall be to contractor's account.

3. To be read in conjunction with Particular Job Specification.

CIV-6 CONCRETE PAVEMENT

Providing and laying reinforced cement concrete pavement 150 mm thick in M-25 grade with 20 mm and down grade crushed stone aggregate in pavement, including earthwork in excavation, preparation of base (i.e. compacted subgrade, 200 thk sand and 100 thk PCC M-10 grade), leaving pockets if necessary, making recess, projections, fixing inserts conduit pipes (GI, PVC, HDPE, etc.) laying in alternate panels, filling the gaps between the panels with bitumen sand mix filler material etc., making slopes, finishing edges, leaving bars for pedestals & sleepers including providing sand fill isolation , shuttering, providing and fixing reinforcing steel, curing, chipping and modification works etc. as specified in any shape, thickness, position and finishing the top surface smooth as per requirement etc. all complete as per drawings, specifications and directions of the Engineer-in-charge.

150mm thick in Pavements in Process Areas (Type - I)

1.Rate to include cost of all labour, tools, tackles, equipment, hire charges, supply of all materials, providing and fixing reinforcement steel, shuttering, earthwork in excavation and backfilling using serviceable earth in all conditions, preparation of base, etc. with all bye works and sundry works. Cost of works towards pipe supports & sleepers being raised from pavement is covered under respective RCC items.

2. To be read in conjunction with Particular Job Specification.

CIV-7 VALVE PIT

Construction and handing over of RCC Valve Pit as per tender drawing, technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per tender drawing.

Construction and handing over of RCC Valve Pit of approx. 1.4m x 1.0 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 3.2m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 2.4m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 2.8m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 2.0m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 2.6m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 1.8 m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 2.5 m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

Construction and handing over of RCC Valve Pit of approx. 1.6 m x 1.6 m in size (internal dimension) as per technical specification and direction of engineer-in-charge complete in all respect. Scope of work shall be as per Sketch attached with the tender.

STEEL STRUCTURAL WORKS

ST-1 Steel structure Fabrication

Supplying, Fabricating & Erecting in position steel structures including single/double leaf gate fabricated out of MS Girders, channels, Tees, angle, flats, plate, square hollow sections pipes etc. conforming to IS:2062 and/or from pipes conforming to IS:1161 for structural purpose for cascade supporting structure, loading/unloading platform, Gratings for platform, catladder,handrails, hoardings for sinages,Lcv stand, etc. of any size/dia for required design including cutting, welding, bolting, hoisting, fixing in position, including application of one coat of primer at shop and second coat of primer at site after erection and two coats of finishing paint at site .The work is to be completed in all respect as per specification ,scope of work, detailed construction drawings and directions of the Engineer-in-charge.

[ Rate to include cost of all labour, nut, bolts, tools, tackles, hire charges royalties, levies, transportation, scrap value, gas cutting, welding, other consumables, paints, compressed air, water, electric power etc. all complete.]

ST-2 Providing and fixing Fencing Structure

Supplying, fabricating & fixing steel structural fencing fabricated from pipes conforming to IS:1161 and plates conforming to IS:2062 & fixing of GI weldmesh made from 3mm GI wire @ 75 mm bothways to structural steel frame by means of welding/bolting, including applying two coats of approved quality of synthetic enamel paint over a priming coat of in approved shade including supply of all raw materials, bolts, electrodes, transportation, including making pokets & pouring with PCC (1:2:4) in of block 500x500x500 for fixing of posts etc complete as per enclosed drawing, technical specifications,scope of works and directions of the Engineer-In-Charge.

Fencing height 2.1m

Fencing height 1.5m

Total Excluding GST

GST (CGST&SGST/UTGST or IGST) in percentage (%) on Total {@18% on sl.no. 568}

Vichitra Constructions Pvt Ltd

Adorn Infra Energy Pvt. Ltd.

DS PIPELINE PROJECTS PRIVATE LIMITED

NEW EOAN ASSOCIATES

G L GOLDEN

Ario Infrastructure Private Limited

Mansi Ganga Builders and Engineers Pvt Ltd

NOPS INFRASTRUCTURE PVT. LTD.

ANERI CONSTRUCTION PRIVATE LIMITED

R S INFRASOLUTIONS PRIVATE LIMITED