Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹30.2 LAccepted-AOC MEHEM ROAD NEAR TVS BIKE AGENCY GOHANA SONIPAT HARYANA 131301 ON MEHAM ROAD NEAR TVS BIKE AGENCY GOHANA 131301 | SONIPAT | HARYANA | 131301 | L1 | Accepted-AOC accepted |
Tender Value
₹24.0 L
EMD Value
₹48,080
Closing Date
2 Nov 2021, 5:00 pmClosed
Executive Engineer
Electrical Division PWD BnR Br. Rohtak
Construction of Primary Health Centre (PHC) including Residence at Lijwana Kalan (Jind) (Pdg. E.I. and Street Light only).
2021_HRY_192676_1
PWD/Electrical/176445
Open Tender
Electrical Works
Item-rate/Agreement basic
60 days
Jind
Please refer to tender documents as per DNIT conditions.
3 documents required · 3 mandatory
₹1,000
₹48,080
Yes
17 Oct 2022
18 Oct 2021
3 Nov 2021
18 Oct 2021
2 Nov 2021
18 Oct 2021
Amount
HSR Items
E.I. Work
Ceiling Fan / Exhaust Fan
20.71 Supply, Erection, Testing of Ceiling Fan IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-Charge
20.72 Supply, Erection, Testing of Exhaust Fan IS marked (as per IS code 374)having a capacity of 45 cubic meter per minute complete with suitable GI sheet ducting in structure confirming to latest IS specifications complete in all respects complete to satisfaction of Engineer-in-Charge
23.1 Copper Wiring in MS Conduit (Surface/Recess)
23.1.1 Wiring for Light/Fan/Call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick conduit pipe.
23.1.1.1 Group A
23.1.1.2 Group B
23.1.2 Wiring for Twin control light point with 2 Nos. 2 way, 5 amp. switch in 1.5 Sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick MS conduit pipe.
23.1.2.1 Group A
23.1.2.2 Group B
23.1.4 Wiring in MS conduit system for 3 pin 5 amp. plug point by using 2 no. 1.5 sqmm FRLS copper wire and 1 No. 1.5 Sqmm FRLS copper wire, including providing 2 no. 5/6 Amp 3/5 pin socket and 1 no. 5/6 Amp switch required MS Box etc complete as required
23.1.4.1 Group A
23.1.4.2 Group B
23.1.5 Wiring in MS conduit system for 3 pin 15 amp. plug point by using 2 no. 4 sqmm FRLS copper wire and 1 No. 4 Sqmm FRLS copper wire foe earthing, including providing 2 no. 15/16 Amp 3/6 pin socket and 1 no. 15/16 Amp switch required MS Box etc complete as required
23.1.5.1 Group A
23.1.5.2 Group B
23.1.6 Wiring main sub mains and circuit wiring in Two single core for phase and neutral wire and one single core for each wire PVC insulated copper conductor cable 1100 volts grade in MS conduit etc complete as required
23.1.6.1 1 run of size 1.50 Sqmm (1/1.40 mm)
23.1.6.3 1 run of size 4 Sqmm (1/2.24 mm)
23.1.6.4 1 run of size 6 Sqmm (1/2.80 mm)
23.1.6.5 1 run of size 10 Sqmm (1/3.50 mm)
23.6.6 Supply and Erection of MS conduit pipe 1.6 mm thick, ISI marked surface / recessed in slab / wall / ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work
23.6.6.1 M S Pipe of 20 mm dia
23.6.6.2 M S Pipe of 25 mm dia
23.8 Fittings and Accessories.
23.8.1 Providing and fixing Paino type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connection, complete in all respect
23.8.1.6 Call bell 220/230 volts musical type
23.8.1.8 Bell push with 4 metres 2-core, 0.50 sqmm (16/0.20) PVC flexible wire
23.8.1.12 Bakelite angle / straight button holder large size.
23.8.1.13 Socket size rotary step type Electronic regulator for AC ceiling fan
23.8.1.14 Telephone Socket
23.8.4 Supply and erection of 10.5 cm dia MS Fan box including 8 mm dia 30 cm long MS road made into suitable suspension hook and erected in RCC slab for the erection of fan complete with all labour and material required to complete the job
23.9 Erection of Exhaust fan in existing opening, complete with necessary earthing of Fan including carriage from PWD store to the site of work
23.10 Erection of Cabin fan complete with necessary earthing including carriage from PWD store to the site of work.
23.11 Making suitable hole in the wall suitable for exhaust fan upto 450 mm sweep including finishing the same and fixing of stainless steel wire mesh 2 mm thick having about 50 meshes per inch at exhaust side complete as required.
23.22 MCCB, Distribution Boards, MCB's, RCCB's, Change Over etc.
23.22.1 Supply and erection of modular case circuit breaker single pole / 4 pole on existing wall / pedestal / panel including bounding to earth and making necessary connections required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work.
23.22.1.1 Double Pole MCCB 16 to 63 Amp., 25 Ka
23.22.1.3 Triple Pole MCCB 16 to 100 Amp., 25 KA
23.22.1.11 4 Pole MCCB 200 to 250 Amp., 25 KA
23.22.2 MCCB enclosure made of sheet steel suitable for mounting MCCB of following ratings
23.22.2.1 MCCB upto 125 A FP
23.22.4 Supply and erection of double door sheet steel enclosure distribution boards suitable for MCB's & ELCB's recessed in wall including bonding to earth complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work.
23.22.4.2 SPN DB Double Door 8 way (2 incoming and 6 outgoing)
23.22.4.5 TPN DB Horizontal type Double Door 4 way (8 incoming and 3 phase * 4 outgoing)
23.22.4.7 TPN DB Horizontal type Double Door 8 way (8 incoming and 3 phase * 8 outgoing)
23.22.4.8 TPN DB Horizontal type Double Door 12 way (8 incoming and 3 phase * 12 outgoing)
23.22.5 Supply and erection of miniature circuit breaker 240/ 415 V in the existing distribution board including making necessary connections
23.22.5.1 6 Amp. to 32 Amp. Single Pole
23.24.4.2 Load Bank 8 way 250 Amp.
24.1 Earthing and Lightening Arrestor
24.1.1 Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. (but without charcoal or coke and salt) as required
24.1.2 Extra for using salt and charcoal/coke for earth electrode as required
24.1.3 Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt ) complete as required
24.1.5 Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode
24.1.7 Supplying and Laying 25mm x 3mm G.I. Strip in 40mm dia GI pipe as/from earth electrode including soldering etc. as required.
24.1.11 Providing and laying earth connections from earth electrode with 4.00 mm dia GI wire in 15 mm dia GI pipe from earth electrode as required.
24.5.2 S/E of mark double walled corrugated (DWC) HDPE pipe10 Kg./Cm2 laid 0.75 mtr. below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-incharge of the work
24.5.2.3 DWC/HDPE pipe 63/50 mm outer dia / inner dia
24.5.2.4 DWC/HDPE pipe 90/75 mm outer dia / inner dia
Street Light
23.5 Coppper Wiring in existing PVC / MS Conduit Pipe Surface / Recessed
23.5.6 Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated copper conductor cable 1100 volts grade in existing MS / PVC conduit etc. as required
23.5.6.1 1 Run of Size 1.50 sqmm (1/1.40mm).
23.22 MCCB, Distribution Boards, MCB's, RCCB's, Change Over etc.
23.22.1 Supply and erection of moulded case circuit breakers single pole / 4 pole on existing wall /pedestal/Panel including bonding to earth and making necessary connections required to complete the job in all respect upto the entire satisfation of the Engineer-in-Charge of the work.
23.22.1.3 Triple Pole MCCB 16 Amp. to 100 Amp., 25 Ka
23.22.2 Mmccb Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings
23.22.2.1 MCCB up to 125 A FP
23.22.4 Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.
23.22.4.5 TPN DB Horizontal type Double Door 4 way (8 incoming and 3 phase * 4 outgoing)
23.22.5 Supply and erection of miniature circuit breaker 240/415 V in the existing distribution board including making necessary connections.
23.22.5.1 6 Amp. to 32 Amp. Single Pole
23.27 Supply and erection of Godrej Almirah typeM.S. pedestal mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with made of 50 mm x 50 mm x 6 suitable hinges and locking arrangement with Godrej type handle including round bars The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of Suitable size on the sides, at top and bottom, each set containing four Nos, holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof. The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer in-charge of the work
23.27.1 M.S. pedestal of size 600 mm wide 750 mm high 300 mm deep and bottom totally open, duly embeded in 1:24 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level, having a base of size 900 mm x 600 mm x 250 mm below ground level
24.1 Earthing and Lightening Arrestor
24.1.1 Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. (but without charcoal or coke and salt) as required
24.1.2 Extra for using salt and charcoal / coke for pipe earth electrode as required
24.1.12 Supplying and laying of 6 S.W.G. G.I. wire at 0.50 meter below ground level from earth electrode including thimbles, soldering etc. as required.
24.5 Miscellaneous Items
24.5.2 Supply and erection of mark double walled corrugated (DWC) HDPE pipe 10 Kg./Cm2, laid 0.75 Mtr. below ground level including diging and refilling of earth including cost of sutiable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.
24.5.2.3 DWC /HDPE pipe 63/50 mm outer dia / inner dia.
24.4 Street Light
24.4.8 Supply & Erection of Hot Dip Galvanized octagonal pole of 3 mm thickness, with base plate including cost of nut and bolts, earthing studs, Integral Cable termination arrangement 5 mm thick bakelite base plate on suitable welded MS/GI bracket 32A four way connector 2 No. 10 A Sp MCB, end cover and all accessories as supplied by the manufacturer including providing RCC foundation of M 25 grade (1 Cement:1Stone aggregate:2Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 80 Kg./Cum of concrete contents, concrete cover 50 mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per follwoing specification complete in all respects and as per directions of Engineer-in-Charge Make: VIPIN ST/GE/PHILLIPS
24.4.8.5 7 Mtr. Long pole with top dia 75 mm and botom dia 150 mm with base plate of size 300 x 300 x 20mm.
24.4.15 B.S.E.N. 10025 High Masts
24.4.15.2 Supply, installation, testing and commissioning of 16 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer -in-Charge Thickness of Top and Bottom Section = 3 mm & 4mm (minimum) Top Dia = 150 mm and Bottom Dia = 410mm Thickness of Galvanization - Top = 65 micron (minimum) and Bottom=85 micron (minimum) Make: VIPIN ST/GE/PHILLIPS
24.4.16 Supply and erection of weather proof M.S. box of size 20 cm x 15 cm x 10 cm. covered with 3.00 mm thick M.S. sheet hinged cover, locking arrangement, housed in wall, including the cost of 1 no. 16 amp. 415 volts SP MCB and 2 nos. 63 amp. 415 volts neutral links fixed on hard wood board/10 mm Bakellite sheet in the M.S. box including painting and necessary connections
MR Items
E.I. Work
NS-1 Supply & erection of M.S. Box made of 16 Gauge of size d 8" x 10" x 4" covered with3 mm thick bakelite sheet white colour of ISI Mark fixed by means of 4 Nos. brass screws with cost of 1 No. 15 Amp. multi socket of ISI Mark and 15 Amp. switch and 3 Nos. 5 Amp. multi-socket with 5 Amp. switches of ISI Mark including fixing the M.S. Box in wall with cost of cement sand mixture including painting of M.S. Box and to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of the work.
NS-2 S/E of underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfation of Engineer-in-Charge of the work.
i) 25 Sqmm 3.5 Core Cable (Armd.)
ii) 120 Sqmm 3.5 Core Cable (Armd.)
Street Light
N.S - 3 Supply and Erection of LED street light lumanaries of Havells make Endura CITYLINER NEOSL 70W LED or its equivalent model and specifications of Crompton/C&S Electric/Phillips/Surya make with die cast housing, toughened glass IP66 with all acessories as supplied by the manufacturer with all labour and material required to complete the job in all respect upto the Entire Satisfaction of the Engineer-in-Charge of the work.
N.S - 4 Supply & Erection of Single/double arm bracket made of 40mm dia G l pipe B class lSl 1.25mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.
i) Single Arm Bracket
N.S - 5 Supply & Erection of LED flood light fitting of Havels make JETA IRI SFL 100W LED or its equivalent make of Crompton/C&S Electric/Phillips/Surya make with pressure die cast alluminium housing, reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer complete in all respect upto the entire satisfaction of Engineer-in-Charge of the work.
N.S - 6 Supply and Erection of LED flood light Luminaire 250W of Makes: Havells make JETAVALOUR FL 240 W LED 757 MODWBLTG or its equivalent model of Philips /C&S Electric/Crompton /Bjaj with lense with high power LED flood light in aluminium PDC housing, toughened glass cover with IP 66 protection and accessories required to complete the job in all repect including erection an making connection with other petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.
N.S - 7 S/E of underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfation of Engineer-in-Charge of the work.
i) 16 Sqmm 4 Core Cable (Armd.)
ii) 25 Sqmm 3.5 Core Cable (Armd.)
N.S - 8 Supply and erection of MS Saddle and clamps duly galvanised , on wall / RCC parapit for fixing underground cable at a distance of 0.60 metre center to center fixed by means of rawl plug including the cost of all labour and material required to complete the job in all respect and upto entire satisfaction of the Engineer-in-charge of work. (Based on Old HSR 31.48)
N.S - 9 Supply and erection of MS stand made of 50mmx50mmx6mm angle iron frame and 150cm long, 30cm wide with MS sheet covering size 30cmx30cm 3.15mm thick fixed on the top of board & legs duly embedded in 1:2:4 cement concrete block 30cm below ground level including the cost of cement sand, welding, painting & fabrication charges etc. up to the entire satisfaction of Engineer - in - charge of the work. (Based on Old HSR 31.51)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .