SPL REPAIR TO BLDG NO 154/09 TO 16 (OR MD ACCN) AND REWIRING IN BLDG NO P-798 TO P-804 (SINGLE JCO LIVING) AT ITARANA CANTT, ALWAR

Amount

Taking down cement or cement lime plaster, of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete rubbish materials complete all as specified and directed.

Demolition of cement concrete (reinforced) in landing slab, chullah hoods, manhole covers, roofs, floors, beams, stair case, landing, chajja and similar suspended work complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars & precast concrete masonry etc complete all as specified and directed.

Demolition of existing lime concrete/PCC padding, roof treatment of any thickness laid over RCC roof/Chajjas etc removing complete layer of bitumen under cocnrete/PCC padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment all as directed and specified.

Taking down chowkats or frames with shutters (without taking off shutters frome the frames) n exc 1.5 but each complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters frome the frames) exc 1.5 but n exc 4 sqm each complete all as specified & directed.

Taking down of shutter and refixing exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc,laid, bedded and pointed in any mortar all as specified & directed.

Cutting holes into stone wall built in cement mortar or cement lime mortar for inserting hold fast and making good dismental portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n exc one brick as required complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 12.5mm graded aggregate) as in levelling coarse of floors and roof complete all as specified and directed.

M&L 75mm thick PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of roof/floor/pavings/path etc complete all as specified and directed.

M&L providing cement concrete type B-0, 1:2:4 (using 12.50 graded stone aggregate) as in padding and levelling course on roof and floor complete all as specified & directed.

M&L cement cocnrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection 75mm thick and surface to be finished even and smooth without using extra cement complete all as specified and directed.

M&L PCC 1:2:4 type B-1 using 20mm graded aggregate as in cills, coping steps, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and alike including weathering, slightly rounded or chemfered angle and throating as directed.

M&L PCC (1:4:8) type D-2 (Using 40mm stone aggregate) as in foundation concrete all as specified and directed.

M&L PCC 1:5:10 type E2 for sunken filling, foundations, filling and mass-concrete complete all as specified and directed.

M&L providing precast cement concrete 1:2:4 type B-1 as in landing, cover slabs (for manholes etc) Chajjas, water troughs, managers, shelves and similar article with plain faces complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B0 in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 including WPC @ 3% by weight of cement on stone/brick masonry finished even and smooth without using extra cement complete all as specified and directed. Note : quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipments reqd to execute the work.

Supply only liquid water profing compound as per IS-2645.

M&L 15mm thick cement plaster in CM 1:6 on fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 10mm thick screed bed on fair faces of concrete/brick surfaces in CM 1:4 with water proofing compound @ 3 % of wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified and directed. (Polymeric membrane and WPC shall be meausred and paid seperately here-in-after)

M&L rendering 5mm thick in CM 1:3 as in ceiling and finish the surface even and smooth without using extra cement complete all as specified and directed.

M&L glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick over 10mm rendering in CM 1:3 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid over 10 mm screed bed or bedding layer in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L vitrified tiles 8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L vitrified tiles 8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L machine cut Green marble flooring 18 to 20mm thick as in floor,cooking platform, treads etc .laid over 20 mm screed bed or bedding layer in CM 1:3 set and jointed in neat cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing by machine and including grinding complete all as specified and directed.

M&L machine cut green marble 18-20 mm thick as in riser of steps, skirting, dado and pillar set over 10 mm rendering in CM 1:3 and jointed with grey cement slurry mixed with pigments to match the shade including rubbing and polishing complete all as specified and directed.

M&L 20-25 mm thick granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 15mm screed bed or bedding layer in CM 1:3 complete all as specified and directed.

M&L machine cut 25 to 30 mm thick kota stone in single piece as in shelves and similar works laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including ball nosing of exposed edges and including dismantling old stone slabs complete all as specified and directed.

S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, both face covered with deco rative face veneer with lipping/frame to match commercial type on both sides with self closing circular knob for locking arrangement all as specified and directed.

M&L factory made 2nd class glazed and skelton door shutter made out of stiles & rails of 35mm thick 2nd class hard wood, klin seasoned and chemically pressure treated & open reabted and prepared to receive glass/gauge etc (without sash bars), edges of framing plain,chamfered of rounded, fitted with and mitred beads for securing glass etc compelte, the size of members of shutter shall be as per IS-1003. The shutter shall be fitted to the chowkhats complete all as specified and directed.

M&L 30mm thick factory made moulded PVC door (Wood free) consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 20mm x 40mm for stiles as well as top, bottom & lock rail. M.S. frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20mm thick multi-chamber hollow PVC section of 1mm wall thickness, bonded using solvent cement / cynoacrylate adhesive with 5 mm (+0.25) thick moulded PVC sheet of density 600 kg/cbm with 2, 4, 6 raised panel deign in plain / prelam colours after routing the moulded design on one side of the inside panel. 5 mm (+0.25) plain / prelam PVC sheet to be pasted using solvent cement / cynoacrylate adhesive on other side of the hollow PVC section. All the four edge of the panel to be sealed with lipping of 10 mm thick & 20 mm wide PVC sheet baton made by sticking 2 nos. foam PVC sheets of 5 mm (+0.25) thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of Plain/Prelam moulded PVC sheet of door 20 mm thick (5 mm x 4 nos.) thick PVC sheet to be given for lock provison at lock height. Door to be fixed with frame with 3 nos. stainless steel butt hinges of size 100mm x 25mm x 2mm and 50 mm long steel screws drilled suitable to pass through both the walls of the M.S. tube other hardware should be fixed with 25mm x 8mm size steel screws etc, complete as per manufacturer’s specification and drawing.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections all as per CEJZ drawing No TD/2004/34(R) sheet No 1/2 to 2/2,, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2 Nos), suitable handle (1 No) complete all as specified & as directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed.

S&F powder coated of any colour as approved anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

S&F sheet glass, ordinary quality 5.5 mm thick fixed with rubber beading and clips size of glass n.exc 2 sqm in each pane complete all as specified and directed.

S&F in repair vitreous china squatting pan of Orrisa pattern size 580mm x 440mm white with integral foot rest (excluding flushing cistern and flush pipe complete incluidng provision of lime concrete bedding fixed complete all as specified and directed.

S&F PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked complete all as specified and directed.

S&F in repair 15mm dia bib tap cast coper alloy chromium plated fancy type crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm dia stop valve/angle valve of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed complete all as specified and directed.

S&F in repair swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 15mm dia concealed stop valve/angle valve of copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union fixed complete all as specified and directed.

S&F WHB angle back of Size 400 x 400 mm excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets and making good any type of surface complete all as specified and directed.

S&F in repair 32 mm dia PVC flexible waste pipe for WHB/Sink 600 mm long with PVC coupling all as directed fixed complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 20mm dia.

S&F 20mm bore tubes medium grade 'galvanised' with and including all fitting and fixed to walls and ceiling or laid in floors complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15mm bore pipe.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 15mm dia.

S&F 15mm bore tubes medium grade 'galvanised' with and including all fitting and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, including taking down old unserviceable sink complete all as specified & directed.

S&F stop valves 20mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

Dismantling of water tanks of capacity exc 250 but n exc 500 ltrs & removing to stores complete all as specified & directed.

S&F 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top)vhoilsted and fixed in position all as specified in SSR Part-I complete all as specified & directed.

S&F in repair ball valve brass high pressure with polythene float and fly nut screwed on iron pipe ad fixed 20 mm bore of pipe complete all as specified & directed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified & directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified & directed.

S&F in repair SS Floor Drainer with Collar and Cockroach Trap/Jali with or without waste hole complete all as specified & directed.

S&F in repair brass chromium plated soap dish complete all as specified.

S&F in repair brass chromium plated towel ring incl a pair of CP brass bracket complete all as specified & directed.

S&F in repair 15mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F UPVC (SWR) pipes of 75mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors including taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F UPVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors including taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F UPVC (SWR) pipes of 75 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F UPVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified & directed.

S&F UPVC (SWR) floor trap, plain with grating including joining with solvent cement 75 mm dia complete all as specified & directed.

S&F UPVC (SWR) bend 75mm bore of any radius complete all as specified & directed.

S&F UPVC (SWR) bend 75mm bore of any radius with access door complete all as specified & directed.

S&F UPVC (SWR) bend 110 mm bore of any radius complete all as specified & directed.

S&F UPVC (SWR) bend 110 mm bore of any radius with access door complete all as specified & directed.

S&F UPVC (SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 110 mm bore with access door complete all as specified & directed.

S&F UPVC (SWR) branch piece single PVC (SWR) (Double T) equal or unequal of 110 mm bore with access door complete all as specified & directed.

S&F UPVC (SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 75 mm bore with access door complete all as specified & directed.

S&F UPVC (SWR) vent cowl 110 mm complete all as specified & directed.

S&F in repair 100mm stack clamp out of 50mm x 5mm flat iron and 16 mm dia round iron stays incl bolts and nuts and securing ends of stays to walls or roof etc, complete all as specified and directed.

S&F in repair 75mm stack clamp out of 50mm x 5mm flat iron and 16mm dia round iron stays incl bolts and nuts and securing ends of stays to walls or roof etc complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, AC, or Reinforced concrete) or 100mm dia set in cement mortar including PCC bed to drain pipe, packing under & haunching against the sides of drain pipes complete all as specified & directed.

S&F 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed.

M&L cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as bed to drain pipe including in packing under and haunching against sides of pipes after they are laid and tested in complete all as specified for 100mm dia pipes.

M&L cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B1 smooth finished and reforming benching as required for 100mm bore pipe.

S&F mild steel butt hinges medium weight colod rolled of size 100mm, ISI marked complete all as specified and directed.

S&F exctruted aluminum alloy with galavanisied mild steel hing pin Butt hinges 100mm long complete all as specified & directed.

S&F aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed all as specified.

S&F aluminum anodised, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified & directed.

S&F extruded aluminium alloy handles 125mm size fabricated type anodized ISI marked complete all as specified & directed.

S&F MS barrel tower bolt 200mm long stove enamelled black with bright bolt & fixed complete all as specified & directed.

S&F MS pressed bow handle of 150mm size oval type stove enamelled black complete all as specified & directed.

S&F MS retractable hinge fixed to wooden or steel frames with Screws/welding as required at site complete all as specified & directed.

S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, with vulcanised rubber piece, fixed in floor complete all as specified & directed.

S&F in repair stainless steel plate rack out of 1.00 mm thick sheet of size 900 x 750 mm and depth of shelves 230 mm with partition for small /large plates made out of stainless steel 24 gauge all as per sample to be hanged on wall by the help of steel screws grouted in walls with rawl plug design as approved by GE complete all as specified & directed.

M&L pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet,12mmdia MS rod for locking, two nos chromium plated handle and one mortise pattern lock inclu two coats of spary painting over a coat of shop primer complete all as shown on drg no TD/2004/29 sheet no 1/3 to 3/3.

S&F in repair harrison rails, mild steel, chromium platd curtain rod with fixing bracket, stops, rollers etc complete all as specified and directed.

S&F in repair stainless steel drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including matching finials at both ends and pair of SS brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm c/c all as specified and directed.

M&L 50mm thick sand stone slab in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other SIde and set and pointed in CM 1:4 complete all as specified & directed.

M&L TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia all as specified.

All as per item No 103.00 above but 6mm to 8mm dia TMT bars.

Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqmm on plan area and getting out in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n exc 25 cm thick in soft/loose soil.

Removing excavated soil to a distance exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in 1:4 as in half brick thick wall complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mean radius, built in CM 1:6 complete all as specified & directed.

S&F frame work such as grills,gratring etc,with ends of bars shouldered &/or riveted or forged into spikes,framed guard bars, barred iron door ladder,frame balusters,walk ways, railing,frame work or water tanks & SImilar work conforming to Fe-290 Gde E-165 complete all as specified & directed.

M&L flat iron as in hold fast welded to angle iron door/window frames complete all as specified & directed.

M&L framed work as in doors or gates or tank cage, angle or other covering door etc to be prepared for handing or sliding with including either hooks and hinges or steel hanging door fittings and including all necessary nuts and bolts and welding reqd and hanging also fastening and fixing complete conforming to FE-290 Gde E-165.

M&L welded mild steel wire mesh of mesh size 30mm x 30mm and wire size 1.40mm including all necessary nuts and bolts/welding clamps reqd for fixing into angle iron frame complete all as specified & directed.

M&L precast cement concrete blocks as in kneelers, apex stones, bed plates, bed blocks, kerb stone in PCC (1:2:4) type B-1 mix using 20 mm graded stone aggregate and set in cement mortar 1:6 all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment over and including 25 to 30mm thick sand cushioning layer complete all as specified & directed.

M&L water proofing treatement to RCC roof slab/chajjas including parapet comprising of following course of treatement/specified from bottom to top (a) Applying Bituminous primer @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b) Applying bitumen layer @ 1.2 kg/sqm including parapets. Note : Bituminous primer shall be 'TANK MASTIC' manufactured by M/S STP Ltd or 'EMW FLATE' M/S Texas India Ltd (c) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm reinforced with non woven polyester fabric weight not less than 150 gms per sqm polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flushing. (d) Applying Heat Resisting Paint over APP membrane as per manufacturer's instructions all as specified and as directed. Note:- Only horizontal roof/chajja area shall be measured for payment purpose.

M&L water proofing treatment in sunken floors described as under :- (i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement. (ii) Preaparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed. Note: (i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level. (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Horizontal floor area shall be measured for payment purpose.

M&L preparation of old painted surfaces of steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, described.

S&F preparation of new steel surface/old untreated of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer described all as specified and directed.

M&L preparation of newly wooden surfaces/old untreated of any description over 10 cm width or girth and applying two coats of synthetic enamel paint (of approved shade) over a coat of pink primer all as specified and directed.

M&L preparation of old wooden surface of any description over 10 cm width or girth and applying one coats of synthetic enamel paint (of approved shade) complete all as specified & directed.

M&L preparing newly plastered surfaces & applying two coats of oil emulsion distempering(OBD) over and including a coat of white wall care putty 2 mm thick over a coat of primer on walls

M&L complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efforsecent salt, trading oil grees spots etc using grinding machine on wall surfaces and preparation of old plastered wall surfaces and applying two coats of oil emulsion distemper (OBD) of approved shed/tint over and including a coat of white wall care putty 2mm thick complete over a coat of primer.

M&L complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efforsecent salt, trading oil grees spots etc on wall surfaces and preparation of old plastered wall surfaces and applying two coats of oil emulsion distemper (OBD) of approved shed/tint over a coat of 2mm thick wall care putty.

M&L preparing newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified & directed.

M&L preparation of old surrfaces and applying two coats of white wash on ceiling complete all as specified & directed.

M&L preparation of old surfaces of wall and applying two coats of white wash on wall complete all as specified & directed.

M&L preparing newly plastered surfaces & applying three coats of white wash on walls complete all as specified & directed.

M&L preparation of previously treated surfaces/old surface of wall and applying one coat cement base paint on old surface of wall complete all as specified & directed.

M&L preparation of old decorated plastered/unplastered surfaces of ceilings & applying one coats of oil bound distemper (OBD) complete all as specified & directed.

M&L preparing newly plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of 2mm thick exterior wall care putty on walls all as specified & as directed. Note:- Wall care putty shall be paid for separately under respective item.

M&L preparing newly pastered surfaces of walls, plastered and applying 2mm thick exterior wall care putty on walls to prepare the surface even and smooth all as specified and as directed.

M&L form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed.

M&L form work to sides for slabs and sides of RCC/PCC bands in walls, horizontal or sloping and SImilar work exc 10 cm but n exc 20cm wide for fair finished concrete surface complete all as specified and directed.

M&L RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in roof, floor, slabs supported on walls complete all as specified & directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed.

Cutting chases exe 10 cm but n exc 20cm in girth in brick/stone wall for fixing of PVC Pipe/GI pipe of 15 & 20 mm bore (concealed in wall) including makink good surface in CM (1:6) & to match with the existing surfaces complete all as specified & directed.

S&F in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

S&F in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density manufactured by an ISO 9000 certified company using for shutter celluca ply 18 mm thick cut in desired size of shutter and fixed with frame of kitchen accesory/cubboard at all four edges of shutter using 13/6 size self tapping steel screws, below cooking platform. The thickness of the shutter is edfe painted by matching colour of PVC ink of plain colour of PVC sheet using complete all as specified and directed by Engineer-in-Charge and manufacturers specification. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

S&F 15mm bore CP brass mixer for WHB/Sink/Wall hot & cold water for screwed down for iron pipe and fixed bore complete all as specified & directed.

Taking down carefully copper/aluminium point wiring for one light /socket/power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings complete all as specified.

M&L point wiring for one light point controlled by one, one way switch with 1.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS and including wooden boxes fixed on wall with and including 3mm thick phenolic laminated sheet top cover for mounting switches, sockets, fan regulators etc complete all as specified.

All as per serial item No 142.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No 142.00 here-in-before but for one exhaust fan point controlled by one switch and regulator.

All as per serial item No 142.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 142.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 142.00 here-in-before but for one bell/buzzer point controlled by one bell push.

All as per serial item No 142.00 here-in-before but for one light point controlled by two, two way switches.

All as per serial item No 142.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, two way, 5 Amp, 230 Volts complete all as specified and directed.

S&F bell push flush type, single pole, 5 Amp, 240 Volts complete all as specified and directed.

S&F bell buzzer AC 230 volts, single pole, complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type and connecting up ISI marked 240 volts complete all as specified & directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make :- Havells Cat Part No LHEXBHP71NW018 or equivalent of Philips/ Crompton Greaves /Bajaj/Wipro.

S&F LED type street DRACO SERIES light luminaire 20 Watt, 230 Volts, 50 Hz including all necessary fitting accessories and LED complete all as directed. Make : C&S Cat Part LTESS20WLED or equivalent of Crompton Greaves/Wipro

S&F lamp holder PVC/Polycarbonatetype with back plate suitable forbatten fittings complete all as specified.

S&F LED bulb energy saving 10/11 watt complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB TPN with 200 Amps rated bus bar, 4 way, 415 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F MCB 63 Amps, three pole & neutral, 415 Volts complete all as specified and directed.

S&F MCB 32/40 Amps, single pole & neutral, 240 Volts complete all as specified and directed.

S&F MCB 6-40 Amps, single pole, 240 Volts 'C' curve, 10KA ISI marked as per IS/IEC 60898-1 2002 complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug(4 Nos) complete all as specified and directed.

S&F in repair cubical metallic box of size 1.00m x 0.90m x 0.30m depth made out of 2mm thick mild steel sheet, front openable, double door with locking arrangement with & including 3mm thick plain sheet clear glass of suitable size fixed to facilitate meter reading, all internal & external steel surfaces painted with two coats of synthetic enamel paint over a coat of red oxide primer, internal wiring with PVC insulated single core multistranded copper conductor FRLS cables IS-694 marked of adequate size but not less than 6 sqmm with proper ferrule & cable gland, box shall be fixed on wall with ‘Anchor’ type /fastener type bolts & nuts (Set of 6 bolts of 12mm dia 200mm long with nuts & washers) grouted into the wall properly to hold the box, writing MES No/Qtr No for each energy meter with thick white synthetic enamel paint, Neoprene rubber gasket shall be provided for proper sealing, box shall have arrangement for fixing electric energy meters – 06 Nos, MCB DB SPN 2 way – 06 Nos, MCB DB SPN 4 way -01 No complete all as directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 16 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M in depth for foundation and getting out in soft/loose soil all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm deep as in soft/loose soil copletete all as specified.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

M&L brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10mm over UG cable for protection complete all as specified & directed.

M&L dry sand (tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L 40mm grade GI pipe (light grade) for protection of LT cable fixed to wall /pole /road crossing including clamps complete all as directed.

M&L sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cables, drawn through & including suitable size of heavy duty PVC conduit ISI marked not less than 32mm dia (external) with wall thickness not less than 1.8mm & conduit fittings/accessories, fixed on surfaces of wall/ceiling complete all as specified and directed. Note:- 02 runs of 6 sqmm size, 01 run of 6 sqmm size cable & conduit with accessories shall be measured as one run length for payment purpose.

Disconnecting from elect connection and taking down carefully the existing electric energy meter of any capacity, any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same inside the old meter inside box carefully including necessary electric connections complete all as directed.

Disconnecting from elect connection and taking down carefully the existing ceiling fan/exhaust fan/geyser of any capacity any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same ceiling fan/exhaust fan/geyser carefully including necessary electric connections complete all as directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

M/S JINDAL ENTERPRISES