Construction of Anganwadi center at Kurunji Nagar, Lawspet Constituency, Puducherry

Amount

Code No. 2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms , lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m -All kinds of soil.

Code No. 2.27 Supplying and filling in plinth with river sand under floors, including watering ,ramming consolidating and dressing complete

Code No.2.27A.1 Supplying and filling with gravel (excluding rock) in trenches , plinth, sides of foundations etc . In layers not exceeding 20 cm in depth consolidating each deposited layers by ramming and watering etc .complete Including all lead and lift.

Code No. 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No. 4.1.10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Code No. 5.1.2 Providing and laying in position specified grade of reinforced cement concrete , excluding the cost of centering , shuttering , finsishing and reinforcement - All work upto plinth level 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Code No. 5.2.2 Reinforced cement concrete work in walls (any thickness) , including attached pilasters, buttresses , plinth and sting courses , fillets , columns , pillars , piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering , finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Code No. 5.3 Reinforced cement concrete work in beams, suspended floors , roofs having slope up to 15 degree landings , balconies , shelves , chajjas , lintels , bands , plain window sills , staircases and spiral stair cases upto floor five level excluding the cost of centering ,shuttering, finishing and reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No. 5.8 Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers , facias and eaves boards upto floor five level excluding the cost of centering , shuttering , finishing and reinforcement , with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Code No. 5.9.1 Centering and shuttering including strutting , propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete

Code No. 5.9.3 Centering and shuttering including strutting , propping etc and removal of form for - Suspended floors , roofs , landings , balconies and access platform

Code No. 5.9.5 Centering and shuttering including strutting , propping etc and removal of form for - Lintels , beams , plinth beams , girders , bressumers and cantilevers

Code No. 5.9.6 Centering and shuttering including strutting , propping etc and removal of form for - Columns , Pillars , Piers , Abutments , Posts and Struts

Code No. 5.9.13 Centering and shuttering including strutting , propping etc and removal of form for - Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

Code No.5.12 Providing , hoisting and fixing upto floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No.5.22A.6 Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete above plinth level - Thermo - Mechanically Treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

Code No.5.23 Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( 1 Cement : 3 Fine Sand )

Code No. 6.1.2 (Addendum) Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Code No. 6.4.2 (Addendum) Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Code No. 6.13.2 (Addendum) Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:4 (1 cement : 4 coarse sand)

Code No. 6.15 Extra for providing and placing in position 2 nos 6mm dia M.S.bars at every third course of half brick masonry

Code No. 8.13.1 Providing and laying Polished Granite stone flooring in required design and patterns , in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc, all complete as specified - Polished Granite stone slab jet Black , Cherry Red , Elite Brown , Cat Eye or equivalent

Code No. 9.1.2P Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Padak wood

Code No. 9.6.1 Providing and fixing 35mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15 : 2001 (Part B) , including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, all complete and panelling with panels of -12mm thick plain grade -1 , medium density flat pressed three layer particle board FPT - I or graded wood particle board FPT -I, IS :3087 marked , bonded with BWP type synthetic resin adhesive as per IS : 848

Code No. 9.62.1 Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc.complte - 300 X 16 mm

Code No. 9.63.1R Providing and fixing ISI marked powder coating tower bolt black finish (Barrel type) with necessary screws etc.complete - 250 x10 mm

Code No. 9.81.1 Providing and fixing bright finished brass handles with screws etc complete - 125 mm

Code No. 9.117.1 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_1mm ), with wall thickness 2.0 mm (+-0.2mm) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 48 x 40 mm

Code No. 9.118.1 Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Code No. 9.147D.1 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50m in height dimension comprising of uPVC multi - chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile , zinc alloy (white powder coated) touch locks with hook , zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I. fastners 100 x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shyall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality , all complete as per approved drawing.(Single / double glass panes , wire mesh and silicon sealent shall be paid separately) - Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 + or - 0.2 mm and single glazing bead of appropriate dimension.(Area of window upto 1.75 sqm) - sliding window size 1.20x1.35 m

Code No. 9.165.1B Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete

Code No. 10.18 Providing and fixing circular / hexagonal cast iron or M.S. sheet box for ceiling fan clamp , of internal dia 140mm ,73mm height , top lid of 1.5 mm thick M.S.sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron / M.S.sheet box by means of 3.3 mm dia round headed screws, one lock at the corners, clamp shall be made of 12 mm dia M.S bar bent to shape as per standard drawing

Code No. 10.5.1 Providing and fixing 1mm thick M.S.sheet door with frame of 40x40x6 mm angle iron and 3mm M.S.gusset plates at the junctions and corners , all necessary fittings complete, including applying a priming coat of approved steel primer - Using M.S.angels 40x40x6mm for diagonal braces

Code No. 10.16.1 Steel work in built up tubular (round,square or rectanglar hollow tubes etc.) trusses etc., including cutting , hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - hot finished welded type tubes

Code No. 10.25.1 Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required all complete

Code No. 10.26.3 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing,staircase railing and similar works, including applying priming coat of approved steel primer - G.I.pipes

Code No. 11.22.1.1 Tile work in skirting, risers of steps and dado upto 2 m height ,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg / sqm, including pointing in white cement mixed with pigment of matching shade complete - marble tiles (polished) Raj nagar - 8mm thick

Code No. 11.37.1 Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make (Nitco / Kajaria) in colours such as white, Ivory, Grey, Fume red brown ,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete

Code No. 11.36A Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 200 x 300 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 200x300 mm

Code No. 12.41.2 Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Code No. 12.42.5.2 Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110 mm bend

Code No. 12.42.6.2 Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Code No. 12.43.2 Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

Code No. 13.8.3 12 mm cement plaster of mix 1:5 (1 cement : 5 fine sand)

Code No. 13.9.2 cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement - 20mm cement plaster

Code No. 13.9.2A 15 mm cement plaster on the rough side of single or half brick wall of mix 1:5 (1 cement : 5 fine sand)

Code No. 13.28.3 12mm thick plain cement mortar bands in cm per cement mortar 1:4 (1cement : 4 fine sand) - raised band

Code No. 13.46.1 Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

Code No. 13.50.1 Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Code No. 13.50.3 Applying priming coat - with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works

Code No. 13.53.1 Painting on G.S.sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution

Code No. 13.61.1 Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Code No. 15.7.4 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Code No. 16.70.2 Providing and fixing G.I.chain link fabric fencing of required width in mesh size 50 x 50 mm including strengthening with 2mm dia wire or nuts , bolts and washers as required complete - Made of G.I.wire of dia 4mm , PVC coated to achieve outer dia not less than 5mm in required colour and shade

Code No. 16.89 Providing wall black board with cement mortar 1:3 ( 1 cement : 3 sand) finishing with a floating coat of neat cement and black pigment mixed in the proportion 1:2 (one cement : two black pigment) and applying one coat of black board paint including 20mm thick cement plaster band 50mm wide in cement mortar 1:3 (1 cement : 3 sand)

Code No. 16.95 Supplying fixing and commisioning of Suguna / Texmo / Sharp 1 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset , pumpset fixing in position and test run etc.complete

Code No. 17.7.7 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 450x300 mm with single 15mm C.P. brass pillar tap

Code No. 17.10.2.2 Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm , including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink without drain board - 610x460 mm bowl depth 200mm

Code No. 17.13.2 Providing and fixing white vitreous china water closet squatting pan (Indian type) - Orissa pattern W.C.pan of size 580x440mm

Code No.17.14.1 Extra for using coloured W.C.pan instead of white W.C.pan - Orissa pattern W.C.pan 580x440mm

Code No.17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete

Code No.18.9.21 Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and the cost of cutting chases and making good the same including testing of joints complete (Concealed work including cutting chases and making good the walls etc.) - 20 mm nominal outer dia pipes

Code No.18.9.22 Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and the cost of cutting chases and making good the same including testing of joints complete (Concealed work including cutting chases and making good the walls etc.) - 25 mm nominal outer dia pipes

Code No.18.63 Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

Code No.18.64 Providing and fixing PTMT swivelling shower, 15mm nominal bore, weighing not less than 40 gms

Code No.18.65 Providing and fixing PTMT Soap dish holder having length of 138 mm , breadth 102 mm, height of 75mm with concealed fitting arrangements , weighing not less than 106 gms

Code No.18.17.1 Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 25mm nominal bore

Code No.18.17.1A Providing and fixing gun metal gate valve with C.I.wheel of approved quality (screwed end) - 20 mm nominal bore

Code No.18.18.2 Providing and fixing ball valve (brass) of approved quality , high or low pressure , with plastic floats complete - 20mm nominal bore

Code No.18.48A Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

Code No.18.54.1 Providing and fixing PTMT bib cock of approved quality and colour – 15mm nominal bore, 86 mm long , weighing not less than 88gms

Code No.19.30.3.1 Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I.cover with frame (light duty) 455 x 610 mm internal dimensions , total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10graded stone aggregate 40mm nominal size ), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete extra complete as per standard design - inside dimensions 600 x 850 mm and 45 cm deep for pipe line with three or more inlets - with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Code No.19.33.1 Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Code No.19.33.1A Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee with door - 110 x110x110 mm

Code No.19.33.1C Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm

Code No.19.33.2 Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter

Code No.19.33.2A Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee with door - 75x75x75mm

Code No.19.33.2C Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm

Code No. 21.3.1 Providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings ( cost of aluminium snap beading shall be paid in basic item) - with float glass panes of 4.0 mm thickness

Code No.32.19A.1.1 Providing and fixing in position precast R.C.C manhole cover and frame of reqired shape and approved quality - LD - 2.5 - rectangular shape 600 x 450 mm internal dimensions

Code No.NPSR Making carnice on wall edges to 10 cm thick to 15 cm wide using brick bats/ flat bricks in cement morter 1:2 (1 cement: 2 fine sand) as per dedailed drawing and trowel finish in two layers at an average thickness of 25 mm with cement mortor 1:4 (1 cement: 4 fine sand) including moulding of arch surface all labour charges scaffolding cost of materials etc., complete. Rate approved by OM vide no. ( T.S.No.62/DB/OM/2022-23, dt.21.11.2022)

Code No.1.17.2 Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface / recessed steel / PVC conduit as required - 2 X 1.5

Code No.1.17.11 Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface / recessed steel / PVC conduit as required -2 x 2.5 sq.mm

Code No.1.17.20 Supplying and drawing following sizes of FRLS PVC Insulated copper conductor single core cable in the existing surface / recessed steel / PVC conduit as required -2 x 4 sq.mm

Code No.1.17.20 Supplying and drawing following sizes of FRLS PVC Insulated copper conductor single core cable in the existing surface / recessed steel / PVC conduit as required -2 x 4 sq.mm

Code No.1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required - 20mm

Code No.1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required - 25mm

Code No.1.22.13 Supplying and fixing metal box of following sizes (nominal per size) on surface or inrecess with suitable size of phenoliclaminated sheet cover in front including painting etc.as required - 200 mm x 300 mm x 60 mm

Code No.1.22.15 Supplying and fixing metal box of following sizes (nominal per size) on surface or inrecess with suitable size of phenoliclaminated sheet cover in front including painting etc.as required - 250 mm x 300MM X 60 mm

Code No.1.23.1 Supplying and fixing following piano type switch / socket on the existing switch box / cover including connections etc.as required - 5/6 A switch

Code No.1.23.3 Supplying and fixing following piano type switch / socket on the existing switch box / cover including connections etc.as required - 2 way 15/16 A switch

Code No.1.23.4 Supplying and fixing following piano type switch / socket on the existing switch box / cover including connections etc.as required - 3 pin 5/6 A socket outlet, piano type ISI marked .

Code No.1.23.5 Supplying and fixing following piano type switch / socket on the existing switch box / cover including connections etc.as required - 6 pin 15/16 A socket outlet

CODE NO. 2.1.1 Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel , making connections ,etc , as required - 32 A TP&N

Code No.2.12.2 Supplying and fixing following rating , double pole , 240 V, Isolator in the existing MCB DB complete with connections ,testing and commissioning etc.as required - 63 A

Code No.2.15.3 Supplying and fixing following rating , four pole ,(three phase and neutral), 415 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections , testing and commissioning etc.as required - 63 A

Code No.5.1 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories , and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal / coke and salt) as required

Code No.8.1.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc.as required - upto 120 sq.mm

Code No.1211 Providing and Fixing 60W LED street Light Fittings ( Orbit )

SI/CODE No . 55/1217 Supplying and Fixing 20mm PVC junction Box, Two Way

SI/CODE No . 66/1229 Providing and Fixing 20mm PVC Bends – medium class – As per IS : 9537 (Part 3)

SI/CODE No . 67/1230 Providing and Fixing 25mm PVC Bends – medium class – As per IS : 9537 (Part 3)

SI/CODE No . 1096/3127-O Providing and Fixing 1200mm Sweep double ball bearing ceiling fan - make almonard / usha

CODE NO. NPSR Providing and Fixing 20 W LED Tube Light Fittings. Make: Philips / Bajaj ( or ) Equivalent.

CODE NO.NPSR Supplying of 4 core X 25 sqmm armoured aluminium U.G cable with I.IS marks (Make - finolex/Polycab)

Code No.NPSR Supplying of 4 core X 25 sqmm armoured aluminium U.G cable with I.IS marks (Make - finolex/Polycab)

Code No.NPSR Providing and Fixing 9W LED Bulb Philips / Bajaji ( or ) Equivalent.

Santhanam K

Balaraman