AR to new Lab in Govt. Poly

Amount

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Conglomerate floor 40 mm thick cement concrete 1:2:4 on 100 mm cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.12)

Terrazzo Skirting or dado or on wall face rubbed and polished to a granolithic finish under layer 12 mm thick cement coarse sand plaster 1:3 and top layer as specified below. (a) with grey cement (i) 18 mm thick with top layer 6 mm thick with white marble Makrana / Narnaul chipping of size 1 mm to 4 mm laid in cement marble powder mix in the ratio of 3:1 (3 parts of cement and one part of marble powder) by weight in proportion of 4:7 (4 parts of cement marble powder mix : 7 parts of white marble chips) by volume complete. (HSR 14.26 a i)

Kotah stone flooring 34 mm to 40 mm thick in any pattern as specified over 12 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62)

Providing & fixing Vitrified Tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: - Tile shall be premium quality (1st quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JONHONSONS & RAK. (HSR 14.89)

12 mm thick cement plaster 1:5 (HSR 15.6)

15 mm thick cement plaster 1:5 on the rough side of single or half brick wall (HSR 15.11)

10 mm thick cement plaster 1:4 (HSR 15.52)

Cement pointing 1:2 deep variety on brick and tile work. (HSR 15.60)

Cement pointing 1:2 flush on brick and tile walls. (HSR 15.62)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5) Ist Quality

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79 (b) (Duplex , Asian, Nerolac etc.) (b) Ist Quality

Providing and applying white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./Birla make) (HSR 16.81)

Providing and fixing commercial type block board, plain lining, butt jointed, including wooden plugs (teak) placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall be payable extra) (HSR 17.49 b) 19mm thick

Factory-manufactured paneled door or glazed window, shutters of commercial hard wood, such as hillock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln-seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete fixed in position ( excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (HSR 17.90 (b)) 35 mm thick

Factory-manufactured wire gauze door and window shutters of commercial hard wood such as hillock, champ, chikrassy and chaplash, etc. (non coniferous timber other teak, conforming to I.S. specification No.1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (style and rails of windows shutter shall be 75 mm wide)- (HSR 17.92 b) 35 mm thick.

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:-(HSR 17.93 (aiii)) 35 mm thick

Supplying and fixing glass panes including special metal sash putty of approved make- (b) Glass panes 4 mm thick upto 40sq. dm area. (HSR 18.30 b)

AMAN ATTRI

Harish Kumar

DEEPAK KUMAR S/O SH. DILBAGH SINGH