MP FUND 2023-2024

Amount

Earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting but inclusive of shoring, strutting and baling out water wherver necessary as per SS 20 B etc., complete complying with standard specifications.

Plain Cement Concrete 1:4:8 (one cement,four sand and eight aggregate) mix using 40mm gauge hand broken hard granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm well rammed etc., complete complying with standard specifications.

Supplying and erecting Centering for sides and soffits including supports and strutting upto 3.29 m high for plane surfaces such as RCC slabs, Rectanular beams, Lintels and Stair case waist slabs conopy etc., in all floors with all cross bracings using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over country wood joists of size 10cm x 6.50cm spaced at about 90cm centre to centre and supported by Casuarian props of 10cm to 13cm dia spaced at 75cm centre to centre etc., complete and as directed by departmental Engineers. A. Plinth Beams

B. Beams and slab Ground floor

C. Columns

Supplying, fabricating and placing in position mild steel/Ribbed for steel roads for all RCC works including cost of steel and binding wire also in all floors, complete complying with standard specifications.

Reinforced Cement Concrete 1: 1 1/2: 3 ( one cement, one and half sand and three aggregate) mix using machine crushed / hand broken 20mm gauge hard broken granite stone jelly for all reinforced cement concrete works connected to this work excluding centering, shuttering and cost of reinforcement grills placed in position, but including laying, vibrating, curing and finishing, fixing fan clamps in the RCC floor and roof slab works wherver necessary and bearing surfaces of the wall at the sides and bottom of the slab, beams shall be finished smooth with cement mortar 1:3 and kraft paper laid without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers. Up to basement

Ground Floor

First Floor

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand ) using new best Chamber Bricks of size 8 ¾” x 4 ¼” x 2 ¾” from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications. A.for foundation and basement

B. For Ground Floor

C.First Floor

Special Ceiling Plastering and finishing all the RCC exposed surfaces such as RCC slabs, sunshades, conopies, staircase steps , etc., with cement mortar 1:3 (one cement three sand) mix to 10mm thick and including hacking the surfaces and providing necessary cement mortar nosing beading as per size, specification wherever necessary using the same mix as directed by the departmental officers etc., complete complying with standard specifications.

Plasteringwith cement mortar 1:5 (one cement three sand) mix to 12mm thick and including hacking the surfaces and providing necessary cement mortar nosing beading as per size, specification wherever necessary using the same mix as directed by the departmental officers etc., complete complying with standard specifications.

Dadooing of walls with glazed tiles of size 15 cm x15cm x 6mm finished thickness with c.m 1:2- and polished with same color cement including all cost and convene of all materials etc.,complete

Paving the floor with descrgned coloured vitrified tiles of size 600 x 600 x 8mm of best quality and approved variety complying / confirming ISI specification land over cement mortar 1:3 (one cement and three sand) 20mm thick and pomted with same coloured cement neatly etc., complete.

Supplying and fixing in position best white glazed earthenware Indian water Closet of approved quality of size 580mm x 440mm. with 'P' or 'S' trap and embedding the closet with trap to shape in position with 40mm brick jelly concrete 1:2:5( one lime ,two sand and five brick jelly) and finishing the top to the required slope and including giving connection to the C.I. soil stracks by dismantling the masonry floor or RCC works and redoing the same to the original condition without anyleakage etc., complete as directed by the departmental officers, ( The water closet should be got approved by the Department Officers before use on work).

Fabricating, supplying and fixing in positon of SOLID PVC DOORS with frames of different sizes as per the specifications given below: PVC door frames made out of best quality PVC extruded section of 40mm * 58 mm * 2.50 mm +/- 0.3 mm thick, having multichamber cross section and duly reinforced with steel to be mitre cut at the corners and welded including providing tie rod at the bottom and necessary weather seal etc., and PVC door shutters made out of extruded plastic section of 60 mm * 24 mm size in the configruation of an "A" section for shutter frames and multi-chamber hollow plastic section of 200 mm *200 mm*1 mm (average thickness) with tongue and groove section for panels etc., with necessary holdfasts, rubber beedings, furniture fittings, locking arrangements etc., complete including dimantling the masnery, making chippings, holes in the RCC column, beam etc., wherever necessary with power drill to the extent required and redoing the same to the original condition after fixing etc., complete as per specifications and as directed by the departmental officers.

LOUVERED VENTILATOR Supplying fabricating and fixing in position of Aluminium anodized natural colour matt finished LOUVERED VENTILATOR using outer frame of size 62 x 38 x 2mm @1.17kg/m and the louvers with moving arrangements will be made with Aluminium channel of size 60 x 30 x 4 mm @ 1.27kg/m with necessary glass panels for louvers 4mm thick Aluminium clips , including all materials,labour,power consumption charges required for fabrication if necessary chipping dismantling making necessary holes in RCC coloumns, Beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as drected by the departmental officers The Aluminium surfaces should be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868/1962 of Anodic thickness of not less than 15 microns (fifteen) complete. All the materials should be got approved by the Engineer incharge before fixing as directed .

Supplying and fixing in position of M.S grills using for windows and ventilators in position including labour charges for fixing furniture fittings for windows & ventilators with standard drawings , etc., complete complying with standard specifications. Grill work For Door

Truss

Supplying and fixing Galvalium Sheet roof using necessary trusses, purlins and ''U" or "J" bolts, nuts, screws, nails and bitumen washers including cost of labour and materials etc., complete complyingg with standard specification as directed by the departmental officers.(0.47 mm Thickness)

Provding and finishing over slopped RCC roof or Sunshade with one course of Ornamental tiles of size 23 x 15 x1.2cm for front elevation laid with c.m 1:3 (one cement three sand 20mm thick and pointed with same mortar mixed with red oxide and WPC at the rate of 2% by weight of cement including neatly finishing etc., complete as per standard specification (The colour and make of the tiles should be approved before execution from the deparmental officers)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheetcover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVCconcealed light / fan Point (for electronic regulator) (5 points per coil).(SD.NO:25)

Supply and fixing of 5A / 15A 3 pin combined flush type wall socket with 15A flush type switch on suitable TW box. Plug point( SD 136 )

Wiring with 2 x 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flushtypeswitch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion withsuitable colour for concealed power plug point ( S.D.NO:40)

Supply and run of 2 of 1.5 sq.mm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour. ( S.D. 54 )

Supply and run of 4 x 6 sqmm (56/0.3) PVC insulated SC unsheathed Cu,conductor of 1100V grade in 32mm dia GI pipe ( class "B") suitably bent at both ends with necessary angle iron up right and end supports for mains. (S.D.73)

Supply and run of 2 x 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 7/20 GI bearer wire for service connection mains. (S.D.65)

Supply and fixing of single box type 4"40W flu fittiing complete with copper choke and condensor with TW round blocks on wall or ceiling with PVC unshealthed copper leads from terminals to the fitting. (S.D.88)

Supply and fixing of WT bulk head fitting with guard (phillips/Bajaj/Crompton/K.Life) suitable for lamp with 11 W CFL bulb.(SD .83)

Supply and fixing of 1400 mm (56") /sweep AC ceiling fan complete with stepped 300W regulator, with the existing down rod on the existing clamps.(SD 108)

Supply and fixing of 16A D P switch with metal clad of 500V with fuse and neutral (sidehandle) on suitable Twbox PWD earthing SD 141

Earthing as per PWD standard with an earth electrode of 2metre Class 'B' Gipipe of dia not less than 32mm complete with necessary masonry work SD 234

Supply and fixing of horizontal type 4way triplepole neutral MCB distribution board in sheet steel enclosure doubledoor (metal) with 40A 4pole MCB isolateras incoming and 12Nos.6A to 32ASPMCB as out going in flush with wall and making good of the concealed portion with earth connection.The MCB DB and MCB' s should be with the ISI mark (like standard make) SD 179

Painting iron works for doors, windows and ventilators, iron bars, weldmesh, wiremesh screen, steel bars , flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors it inclusive of cost of materials and labour, brushes and scaffolding etc., complete complying with standard specifications.

Emulsion paint two coats using best approved colour and quality cement paint in all floors including cost of lime and other materials, brushes, scafolding charges etc., complete complying with standard specifications and as directed by departmental officers.

Providing paverblock 83 mm thick of best quality with base cushion of 150 mm thick including cost and conveyance of all other labour and material charges to site etc., complete complying with standard specifications.

Supply and fixing of 1000 litre HDPE water Tank

Supply and fixing PVC and GI Special 6"PVC PIPE

4"PVC PIPE

4"PVC BEND

4"PVC TEE

1.5"PVC PIPE

1.5"PVC BEND

1.5"PVC TEE

INBANIDHI CONSTRUCTIONS