Balance work of Mediation Center at State Consumer Dispute Redressel Commission at Distt. Jhansi.

Providing & Laying of 8 to10mm thick ivory of light shade vitrified tiles of 600x600mm size of flooring of skirting laid with 1:3 cement mortar (1cement:3coarse sand) finished with cement slurry & with pigment grouting & polishing complete i/c supply of all material, labour T&P required for proper completion of the work. (In Flooring)

Providing & Laying of 8to10mm thick ivory of light shade vitrified tiles of 600x600mm size of flooring of skirting laid with 1:3 cement mortar (1cement:3coarse sand) finished with cement slurry & with pigment grouting & polishing complete i/c supply of all material, labour T&P required for proper completion of the work. (In Skiritn)

kota stone slab20mm thick in riser of steps , skirting laid on 12mm thick with 1:3 cement mortar (1cement:3coarse sand) finished with grey cement slurry mixed with pigment to match the sgade of the slab including rubbing & polishing complete.

Supply and fixing of 6mm thick China white glazed tile in flooring or in skirting or dado laid with 1:3 cement & approved coarse sand mortar finished with white cement slurry, jointing and polishing complete including supply of all materials, labour and tools and plants.

Supply and fixing of 6mm thick China white glazed tile in flooring or in skirting or dado laid with 1:3 cement & approved coarse sand mortar finished with white cement slurry, jointing and polishing complete including supply of all materials, labour and tools and plants.

Providing & fixing ISI marked flush door shutters conforming IS: 2202 decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters (a) 35mm thick including ISI marked stainless steel butt hinges with necessary screw WITH HIGH PRESSURE DECORATIVE LAMINATED SHEET COMPLETE.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.67 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 0.9LTR / 10 sqm).

Distempering (Two coat) with 1st quality acrylic distemper having voc content less than 50 gram/ltr of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger, J & N, Shalimar, Asian paints after thoroughly .

Distempering (Two coat) with 1st quality acrylic distemper having voc content less than 50 gram/ltr of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger, J & N, Shalimar, Asian paints after thoroughly .

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

appling priming coats with primer of approved brand and manufacture having voc content less than 50 gram/ltr of required shade on wood work & including a priming coat with cement primer of approved brand & manufacture such as Berger, J & N, Shalimar, Asian paints after thoroughly .

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm .

Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete 250 mm x 10mm

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete.

Providing flat iron brackets 50x3mm size with necessary bolts,nuts and washers etc for g.s. sheets & gutters with purlins.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and drawing following pair 0.5 sqmm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required.2pair

supply and fixing of 25 mm dia heavy duty PVC conduit partly concealed in wall,cutting the wall complete.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required Telephone socket outlet.

Supply fixing of stepped type electronic fan regulator (Modular) 120-280 V. ISI marked, on the existing switch board including making connetion, required material, labour T/P etc for proper completion of work to the satisfaction of Engineer in charge of work.

Supplying and fixing modular blanking plate on the existing modular plate & switch box complete.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including as required.1 or 2 module (75mmx75mm).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation ,Testing, Commissioning of pewired ,flourescent fitting / compact fluorescent fitting of all type complete with all accessories including connections etc. as required.

Installation ,Testing, Commissioning of ceiling fan for room height upto with G.I. down rod with standered duly painted, complete in all respects.

Installation ,Testing, Commissioning of exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. Up to 450mm sweep

Extra for fixing the louvers /shutters complete with frame for exhust fans of all size.

Supply & fixing hexagonal/Round cast iron or m.s. sheet Fan box of approved make made up of 1.5 mm thick ISI marked m.s.. Sheet spot mm for pipe entry of the box. Holes should be semi-shuttered type with 1.5mm. Sheet made upper & lower cover duly screwed zink coated M.S. Bar x 12mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material labour, T & P etc required for proper completion of the work.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 1200 mm sweep ceiling fan

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 4 way (4 + 12), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing single pole blanking plate on the existing MCB DB complete.

Supplying and fixing rateing four pole 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40amp

Supplying and fixing cable end box loose wire box suitable for following triple pole and neutral sheet steel,mcb db 415 volts on surface/recess complete with connections, testing and commissioning etc.

Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required.

Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

laying of one number pvc sheathed /xlpe power cable 1.1kv grade of following size direct in ground including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. up to 35sqmm

Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4x10sqmm (25mm).

providing ,laying and fixing following dia g.i.pipe medium class in ground complete.80 mm dia

Supplying and fixing following size of 1.1 kv grade multicore aluminium conductor pvc sheathed armoured cable as per is:1554.(10sqmmx4 core)

Supply and Fixing of 1x17 w mirror Light complete in all respect.

Supply and Fixing of 12 W LED BULB complete in all respect.

Supply and Fixing of LED Tube Light with batten suitable for up to 1X20 watt LED tube light fitting complete including tube on surface complete in all respect.

Supply & fixing ofrecess/Surface/Pendent mounting round 10 to 15 watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set complete in all respects.

Supply of AC 230/250 Volts, 50 Hz 55 w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: HAVELLS.300MM SWEEP

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110MM

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110MM

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110MM BEND

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing & fixing white vitereous china water closet squatting pan ISI marked (Indian type W.C. pan) with 100mm sand cast iron P or S trap, 10/12.5 litrs PVC low level flushing cistern with fittings & brackets 40mm dia C.P. flush pipe with fitting & clamps, 20mm over flow pipe with specials and mosquito proof coupling of approved municipal design, painting wherever required including cutting & making good the walls & floors where required.Orissa Pattern W.C. pan of size 580x 440m with integral type foot rests flush pipe and over flow arrangement.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked black solid plastic seat and lid

Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15mm brass pillar taps, brass chain with rubber plug, 32mm brass waste of standard pattern including cutting & making good the walls wherever required.a)White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.32 mm dia (for wash basin)

Providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with C.P. brass screws and washers.

Providing & fixing PTMT towelrail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw 450mm. Long with total length of 495mm, width 78mm and effective height of 88mm. A 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing unplasticised PVC connection pipe with brass unions 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 (a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

75 mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm

75 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 110 mm

Bend 87.5°110 mm bend

75 mm bend

Shoe plain110 mm bend

75 mm bend

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.20 mm dia nominal outer dia

Providing & fixing G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc.Exposed on wall. (internal work) 15mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality. 15mm dia nominal bore.

20mm dia nominal bore.

25mm dia nominal bore.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :15mm dia nominal bore.

20mm dia nominal bore.

25mm dia nominal bore.

Providing and fixing gun metal gate valve with wheel of approved quality. 25mm dia nominal bore

Providing and fixing brass stop cock of approved quality :20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.a) Pipes 80mm to 300mm diameter.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :a) 150mm diameter

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.a) 150mm diameter

P & fixing square mouth S.W. Gully trap grade 'A' comp. with C.I. grating brick masonry chamber with F.P.S. bricks of class designation 75 & water tight C.I. cover with frame of 300 x 300mm. size (inside) the weight of cover to be not less than 4.50 Kg & frame to be not less than 2.70 Kg as per standard design.a) 150 x 100 mm. size P type

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:nside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

GST Extra as per Applicable

Please Enable Macros to View BoQ information